generic__raw_read_trylock() was broken, fix up the __raw_read_trylock()
implementation for something sensible. Taken from m32r, which has the
same use cases.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Move the call to ib_register_device() later, since a device should not
be registered until it is completely read to be used. This fixes
crashes that occur if an upper-layer driver such as IPoIB is loaded
before the ehca module.
Signed-off-by: Hoang-Nam Nguyen <hnguyen@de.ibm.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The PSN used to generate the request following a RDMA read was
incorrect and some state booking wasn't maintained correctly. This
patch fixes that.
Signed-off-by: Ralph Campbell <ralph.campbell@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Reorganize code relating to cma_get_net_info() and rdam_create_id() to
optimize error case handling (no need to alloc memory/etc. as part of
rdma_create_id() if input parameters are wrong).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eliminate remove_list by using list_del_init() instead during device
removal handling.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On reporting a route error, also include the status for the error,
rather than indicating a status of 0 when an error has occurred.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The race is as follows:
A process : cma_process_remove() calls cma_remove_id_dev(),
which sets id state to CMA_DEVICE_REMOVAL and
calls wait_event(dev_remove).
B process : cma_req_handler() had incremented dev_remove,
and calls cma_acquire_ib_dev() and on failure
calls cma_release_remove(), which does a
wake_up of cma_process_remove(). Then
cma_req_handler() calls rdma_destroy_id();
A Process : cma_remove_id_dev() gets woken and checks the
state of id, and since it is still (wrongly)
CMA_DEVICE_REMOVAL, it calls notify_user(id)
and if that fails, the caller - cma_process_remove()
calls rdma_destroy_id(id). Two processes can
call rdma_destroy_id(), resulting in one
de-referencing kfreed id_priv.
Fix is for process B to set CMA_DESTROYING in cma_req_handler()
so that process A will return instead of doing a rdma_destroy_id().
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cma_connect_ib() and cma_connect_iw() leak cm_id's in failure cases.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
On a machine with no machzwd, loading the module prints out..
machzwd: MachZ ZF-Logic Watchdog driver initializing.
0xffff
machzwd: Watchdog using action = RESET
- the 0xffff printk is unnecessary
- 0xffff seems to be 'hardware not present'
- fix CodingStyle. (This driver could use some more work here)
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Return ENOTTY instead of ENOIOCTLCMD in user-visible ioctl() results
The watchdog drivers used to return ENOIOCTLCMD for bad ioctl() commands.
ENOIOCTLCMD should not be visible by the user, so use ENOTTY instead.
Signed-off-by: Samuel Tardieu <sam@rfc1149.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
If the driver is not configured for `no way out`,
then the open method should not automatically allow
the setting of allow_close to CLOSE_STATE_ALLOW.
The setting of allow_close nullifies the use of
the magic close via the write path. It means that
in the default state, the watchdog will shut-down
even if the magic close has not been issued.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Add io spinlocks to prevent possible race
conditions between start and stop operations
that are issued from different child processes
where the master process opened /dev/watchdog.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Duh. I screwed up editing David Howells patch in commit
3f2e05e90e, and the actual declaration for
the sigset_from_compat() function went missing. My bad.
Olaf Hering saved the day and noticed that I'm a moron.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change remove code so that we first detach
the driver from userspace, then clean up the
clock and then clean up the memory we allocated.
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Add watchdog support for Philips PNX4008 ARM board inlined.
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Use refcounting for pci device obtaining.
Use PCI_DEVICE macro.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Cc: Andrew Morton <akpm@osdl.org>
Convert pci_find_device to pci_get_device + pci_dev_put
in alim watchdog cards' drivers (refcounting).
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Andrew Morton <akpm@osdl.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (37 commits)
[netdrvr] hp100: encapsulate all non-module code
drivers/net/wireless/{airo,ipw2100}: fix error handling bugs
[netdrvr] phy: Fix bugs in error handling
[PATCH] spidernet: Use pci_dma_mapping_error()
[PATCH] sky2: version 1.9
[PATCH] sky2: fragmented receive for large MTU
[PATCH] sky2: use netif_tx_lock instead of LLTX
[PATCH] sky2: incremental transmit completion
[PATCH] sky2: name irq after eth for irqbalance
[PATCH] sky2: workarounds for some 88e806x chips
[PATCH] sky2: use standard pci register capabilties for error register
[PATCH] sky2: gigabit full duplex negotiation
e100, e1000, ixgb: increment version numbers
ixgb: convert to netdev_priv(netdev)
ixgb: combine more rx descriptors to improve performance
e1000: possible memory leak in e1000_set_ringparam
e1000: Janitor: Use #defined values for literals
e1000: don't strip vlan ID if 8021q claims it
e1000: rework polarity, NVM, eeprom code and fixes.
e1000: driver state fixes (race fix)
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6:
JFS: White space cleanup
[PATCH] JFS: return correct error when i-node allocation failed
JFS: Remove shadow variable from fs/jfs/jfs_txnmgr.c:xtLog()
* git://git.infradead.org/mtd-2.6:
[MTD] Cleanup of 'ioremap balanced with iounmap for drivers/mtd subsystem'
[MTD] fix nftl_write warning
[MTD] fix printk warning
[MTD ONENAND] Check OneNAND lock scheme & all block unlock command support
[MTD ONENAND] Remove unused MTD_ONENAND_SYNC_READ configuration
[MTD ONENAND] Fix OneNAND probe
[MTD NAND] Provide prototype for newly-exported nand_wait_ready()
[MTD] Remove #ifndef __KERNEL__ hack in <mtd/mtd-abi.h>
[MTD NAND] Allow override of page read and write functions.
[MTD NAND] Allocate chip->buffers separately to allow it to be overridden
[MTD NAND] Split nand_scan() into two parts; allow board driver to intervene
[MTD NAND] Export nand_wait_ready() for use by board drivers
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (35 commits)
Input: wistron - add support for Acer TravelMate 2424NWXCi
Input: wistron - fix setting up special buttons
Input: add KEY_BLUETOOTH and KEY_WLAN definitions
Input: add new BUS_VIRTUAL bus type
Input: add driver for stowaway serial keyboards
Input: make input_register_handler() return error codes
Input: remove cruft that was needed for transition to sysfs
Input: fix input module refcounting
Input: constify input core
Input: libps2 - rearrange exports
Input: atkbd - support Microsoft Natural Elite Pro keyboards
Input: i8042 - disable MUX mode on Toshiba Equium A110
Input: i8042 - get rid of polling timer
Input: send key up events at disconnect
Input: constify psmouse driver
Input: i8042 - add Amoi to the MUX blacklist
Input: logips2pp - add sugnature 56 (Cordless MouseMan Wheel), cleanup
Input: add driver for Touchwin serial touchscreens
Input: add driver for Touchright serial touchscreens
Input: add driver for Penmount serial touchscreens
...
Revert Andrew Morton's patch to temporarily hack around the lack of a
declaration of sigset_t in linux/compat.h to make the block-disablement
patches build on IA64. This got accidentally pushed to Linus and should
be fixed in a different manner.
Also make linux/compat.h #include asm/signal.h to gain a definition of
sigset_t so that it can externally declare sigset_from_compat().
This has been compile-tested for i386, x86_64, ia64, mips, mips64, frv, ppc and
ppc64 and run-tested on frv.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are a few places in the kernel where the init task is signaled. The
ctrl+alt+del sequence is one them. It kills a task, usually init, using a
cached pid (cad_pid).
This patch replaces the pid_t by a struct pid to avoid pid wrap around
problem. The struct pid is initialized at boot time in init() and can be
modified through systctl with
/proc/sys/kernel/cad_pid
[ I haven't found any distro using it ? ]
It also introduces a small helper routine kill_cad_pid() which is used
where it seemed ok to use cad_pid instead of pid 1.
[akpm@osdl.org: cleanups, build fix]
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
proc_pid_make_inode:
ei->pid = get_pid(task_pid(task));
I think this is not safe. get_pid() can be preempted after checking "pid
!= NULL". Then the task exits, does detach_pid(), and RCU frees the pid.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was pointed out that since I am taking ARRAY_SIZE anyway the trailing empty
entry is silly and just wastes space.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The value doesn't change but this ensures I will have the proper value when
other files are added to proc_base_stuff.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
task_state() needs tasklist_lock to protect ->parent/->real_parent. However
task->parent points to nowhere only when the actions below happen in order
1) release_task(task)
2) release_task(task->parent)
3) a grace period passed
But 3) implies that the memory ops from 1) should be finished, so pid_alive()
can't be true in such a case.
Otherwise, we don't care if ->parent/->real_parent changes under us.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Drop tasklist_lock. ->siglock protects almost all interesting data
(including sub-threads traversal) except:
->signal->tty
protected by tty_mutex
->real_parent
the task can't be unhashed while we are holding
->siglock, so ->real_parent can change from under us
but we can safely dereference it under rcu_read_lock()
->pgrp/->session
we can get inconsistent numbers if the task does
sys_setsid/daemonize at the same time. I hope this
is acceptable.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
lock_task_sighand() can take ->siglock without holding tasklist_lock.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The implementation is exactly the same and there is currently nothing to
distinguish proc_tid_attr, and proc_tgid_attr. So it is pointless to have two
separate implementations.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The hard coded inode numbers in proc currently limit its maintainability,
its flexibility, and what can be done with the rest of system. /proc limits
pid-max to 32768 on 32 bit systems it limits fd-max to 32768 on all systems,
and placing the pid in the inode number really gets in the way of implementing
subdirectories of per process information.
Ever since people started adding to the middle of the file type enumeration we
haven't been maintaing the historical inode numbers, all we have really
succeeded in doing is keeping the pid in the proc inode number. The pid is
already available in the directory name so no information is lost removing it
from the inode number.
So if something in user space cares if we remove the inode number from the
/proc inode it is almost certainly broken.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
To remove the hard coded proc inode numbers it is necessary to be able to
create the proc inodes during readdir. The instantiate methods are the subset
of lookup that is needed to accomplish that.
This first step just splits the lookup methods into 2 functions.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch generalizes the concept of files in /proc that are related to
processes but live in the root directory of /proc
Ideally this would reuse infrastructure from the rest of the process specific
parts of proc but unfortunately security_task_to_inode must not be called on
files that are not strictly per process. security_task_to_inode really needs
to be reexamined as the security label can change in important places that we
are not currently catching, but I'm not certain that simplifies this problem.
By at least matching the structure of the rest of proc we get more idiom reuse
and it becomes easier to spot problems in the way things are put together.
Later things like /proc/mounts are likely to be moved into proc_base as well.
If union mounts are ever supported we may be able to make /proc a union mount,
and properly split it into 2 filesystems.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move execve() into arch/avr32/kernel/sys_avr32.c, rename it to
kernel_execve() and return the syscall return value directly without
setting errno.
This also gets rid of the __KERNEL_SYSCALLS__ stuff from unistd.h and
expands #ifdef __KERNEL__ to cover everything in unistd.h except the
__NR_foo definitions.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The last in-kernel user of errno is gone, so we should remove the definition
and everything referring to it. This also removes the now-unused lib/execve.c
file that was introduced earlier.
Also remove every trace of __KERNEL_SYSCALLS__ that still remained in the
kernel.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
