When read valid tx/rx chains from EEPROM, there is a bug to use the
tx chain value for both tx and rx, the result of this cause low
receive throughput on 1x2 devices becuase rx will only utilize single
chain instead of two chains
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k_reset must be called with sc->lock. Since the tx queue
watchdog runs in a workqueue and accesses sc, it's appropriate
to just take the lock over the whole function.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power detector adc offset calibration has to be done
on 4 minutes interval (longcal * pa_skip_count). But the commit
"ath9k_hw: fix a noise floor calibration related race condition"
makes the PA calibration executed more frequently beased on
nfcal_pending value. Running PAOffset calibration lesser than
longcal interval doesn't help anything and the worse part is that
it causes NF load timeouts and RX deaf conditions.
In a very noisy environment, where the distance b/w AP & station
is ~10 meter and running a downlink udp traffic with frequent
background scan causes "Timeout while waiting for nf to load:
AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state.
This issue was originaly reported in Android platform where
the network-manager application does bgscan more frequently
on AR9271 chips. (AR9285 family usb device).
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is an interoperability with AR9382/AR9380 in L1 state with a
few root complexes which can cause a hang. This is fixed by
setting some work around bits on the PCIE PHY. We fix by using
a new ini array to modify these bits when the radio is idle.
Cc: stable@kernel.org
Cc: Jack Lee <jack.lee@atheros.com>
Cc: Carl Huang <carl.huang@atheros.com>
Cc: David Quan <david.quan@atheros.com>
Cc: Nael Atallah <nael.atallah@atheros.com>
Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In case of single tx and rx queues, three MSI-x vectors are allocated instead
of two. This patch fixes that.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Access to cmd register is racey, especially in smp environments. Protect
it using a spinlock.
Signed-off-by: Matthieu Bucchianeri <matthieu@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a small possibility of a race where the suspend routine gets
called, while a napi callback is still pending and when that comes up,
it enables interrupts which just got disabled in the suspend routine.
This change adds napi disable call in suspend and enable in resume to
avoid race.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Show per-queue stats in ethtool -S output for vmxnet3 interface. Register dump
of ethtool should dump registers for all tx and rx queues.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a performance enhancement fix. vmxnet3 device performs better when
provided with at least 54 bytes (ethernet 14 + IP 20+ TCP 20) in the first SG
buffer. For UDP packets driver provides lesser than that in first sg. This
change fixes the same. Also avoid the redundant pskb_may_pull() call.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make hw vlan tag stripping as enabled by default. Thereby remove
the code to conditionally enable it later.
Signed-off-by: Guolin Yang <gyang@vmware.com>
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While activating the device get it's MAC address from netdev. This will allow
the MAC address configured using ifconfig to persist through the reset.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug while changing ring size when MTU is changed.
Signed-off-by: Shreyas N Bhatewara <sbhatewara@vmware.com>
Acked-by: Dmitry Torokhov <dtor@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the original code we check if (servl == NULL) twice. The first time
should print the message that cfmuxl_remove_uplayer() failed and set
"ret" correctly, but instead it just returns success. The second check
should be checking the value of "ret" instead of "servl".
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes the CAN socket code conform to the manpage of sendmsg.
Signed-off-by: Kurt Van Dijck <kurt.van.dijck@eia.be>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some OSA level have a bug in the hw tx csum logic. We can circumvent
this bug by turning on IP hw csum also.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The open function of qeth is not executed if the qeth device is in
state DOWN or HARDSETUP. A recovery switches from state SOFTSETUP to
HARDSETUP to DOWN to HARDSETUP and back to SOFTSETUP. If open and
recover are running concurrently, open fails if it hits the states
HARDSETUP or DOWN. This patch inserts waiting for recovery finish
in the qeth open functions to enable successful qeth device opening
in spite of a running recovery.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Linux 2.6.21 defines different macros for __attribute__ which are also
used inside batman-adv. The next version of checkpatch.pl warns about
the usage of __attribute__((packed))).
Linux 2.6.33 defines an extra macro __always_unused which is used to
assist source code analyzers and can be used to removed the last
existing __attribute__ inside the source code.
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Fixes the following:
1. POLL should not enable IRQ when work is not completed
2. No locking between TX descriptor cleaning and XMIT descriptor handling
3. No locking between RX POLL and XMIT modifying control register
4. Since TX cleaning (called from POLL) is running in parallel with XMIT
unnecessary locking is needed.
5. IRQ handler looks at RX frame status solely, this is wrong when IRQ is
temporarily disabled (in POLL), and when IRQ is shared.
6. IRQ handler clears IRQ status, which is unnecessary
7. TX queue was stopped in preventing cause when not MAX_SKB_FRAGS+1
descriptors were available after a SKB been scheduled by XMIT. Instead
the TX queue is stopped first when not enough descriptors are available
upon entering XMIT.
It was hard to split up this patch in smaller pieces since all are tied
together somehow.
Note the RX flag used in the interrupt handler does not signal that
interrupt was asserted, but that a frame was received. Same goes for TX.
Also, IRQ is not asserted when the RX flag is set before enabling IRQ
enable until a new frame is received. So extra care must be taken to
avoid enabling IRQ and all descriptors are already used, hence dead lock
will upon us. See new POLL implementation that enableds IRQ then look at
the RX flag to determine if one or more IRQs may have been missed. TX/RX
flags are cleared before handling previously enabled descriptors, this
ensures that the RX/TX flags are valid when determining if IRQ should be
turned on again.
By moving TX cleaning from POLL to XMIT in the standard case, removes some
locking trouble. Enabling TX cleaning from poll only when not enough TX
descriptors are available is safe because the TX queue is at the same time
stopped, thus XMIT will not be called. The TX queue is woken up again when
enough descriptrs are available.
TX Frames are always enabled with IRQ, however the TX IRQ Enable flag will
not be enabled until XMIT must wait for free descriptors.
Locking RX and XMIT parts of the driver from each other is needed because
the RX/TX enable bits share the same register.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frame error interrupts must also be handled since the RX flag only indicates
successful reception, it is unlikely but the old code may lead to dead lock
if 128 error frames are recieved in a row.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A new SKB buffer should not be allocated when the old SKB is reused.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is safe to enable all fragments before enabling the first descriptor,
this way all descriptors don't have to be processed twice, added extra
memory barrier.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When NAPI is disabled there is no point in having IRQs enabled, TX/RX
should be off before clearing the TX/RX descriptor rings.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Unfortunately, not all CONFIG_OF platforms provide
pci_device_to_OF_node().
Change the test to CONFIG_SPARC for now to deal with
the build regressions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor comment errors and whitespace issues discovered while looking
into this are also addressed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
If hardware asserted an interrupt and driver is down,
then there is nothing to do so return IRQ_HANDLED
instead of IRQ_NONE. Returning IRQ_NONE in above
situation causes screaming IRQ on virtual machines.
CC: Andy Gospodarek <gospo@redhat.com>
Signed-off-by: Tushar Dave <tushar.n.dave@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The firmware agent is not available during resume. Loading the firmware
during open() (see eee3a96c63) is not
enough.
close() is run during resume through rtl8169_reset_task(), whence the
mildly natural release of firmware in the driver removal method instead.
It will help with http://bugs.debian.org/609538. It will not avoid
the 60 seconds delay when:
- there is no firmware
- the driver is loaded and the device is not up before a suspend/resume
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Tested-by: Jarek Kamiński <jarek@vilo.eu.org>
Cc: Hayes <hayeswang@realtek.com>
Cc: Ben Hutchings <benh@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use is_unicast_ether_addr from linux/etherdevice.h instead of custom
macros.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
From a check for !is_multicast_ether_addr it is not always obvious that
we're checking for a unicast address. So add this helper function to
make those code paths easier to read.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is completely untested as I don't have an ARM build environment.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ethtool operations can only be implemented for the WAN port, and
not all such operations are allowed to return an error code such as
-EOPNOTSUPP. Therefore, define two separate ethtool_ops structures
for WAN and non-WAN ports; simplify and rename the WAN-only functions.
This is completely untested as I don't have an ARM build environment.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_clone() dynamically allocates memory and may fail. If it does it
returns NULL. This means we'll dereference a NULL pointer in
drivers/net/usb/cdc_ncm.c::cdc_ncm_rx_fixup().
As far as I can tell, the proper way to deal with this is simply to goto
the error label.
Furthermore gcc complains that 'skb' may be used uninitialized:
drivers/net/usb/cdc_ncm.c: In function ‘cdc_ncm_rx_fixup’:
drivers/net/usb/cdc_ncm.c:922:18: warning: ‘skb’ may be used uninitialized in this function
and I believe it is right. On the line where we
pr_debug("invalid frame detected (ignored)" ...
we are using the local variable 'skb' but nothing has ever been assigned
to that variable yet. I believe the correct fix for that is to use
'skb_in' instead.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Regardless of whether the firmware update being performed by
vxge_fw_upgrade() is a success or not we must still remember to always
release_firmware() before returning.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Acked-by: Ram Vepa <ram.vepa@exar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
icv_truncbits is set to 256 for sha512, so update
MAX_AH_AUTH_LEN to 64.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent changes, (percpu stats on vlan/tunnels...), we dont need
anymore per struct netdev_queue tx_bytes/tx_packets/tx_dropped counters.
Only remaining users are ixgbe, sch_teql, gianfar & macvlan :
1) ixgbe can be converted to use existing tx_ring counters.
2) macvlan incremented txq->tx_dropped, it can use the
dev->stats.tx_dropped counter.
3) sch_teql : almost revert ab35cd4b8f (Use net_device internal stats)
Now we have ndo_get_stats64(), use it, even for "unsigned long"
fields (No need to bring back a struct net_device_stats)
4) gianfar adds a stats structure per tx queue to hold
tx_bytes/tx_packets
This removes a lockdep warning (and possible lockup) in rndis gadget,
calling dev_get_stats() from hard IRQ context.
Ref: http://www.spinics.net/lists/netdev/msg149202.html
Reported-by: Neil Jones <neiljay@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jarek Poplawski <jarkao2@gmail.com>
CC: Alexander Duyck <alexander.h.duyck@intel.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Sandeep Gopalpet <sandeep.kumar@freescale.com>
CC: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a problem in net/batman-adv/unicast.c::frag_send_skb().
dev_alloc_skb() allocates memory and may fail, thus returning NULL. If
this happens we'll pass a NULL pointer on to skb_split() which in turn
hands it to skb_split_inside_header() from where it gets passed to
skb_put() that lets skb_tail_pointer() play with it and that function
dereferences it. And thus the bat dies.
While I was at it I also moved the call to dev_alloc_skb() above the
assignment to 'unicast_packet' since there's no reason to do that
assignment if the memory allocation fails.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Sven Eckelmann <sven@narfation.org>
When the buffer size is set to zero in the block ack parameter set
field, we should use the maximum supported number of subframes. The
existing code was bogus and was doing some unnecessary calculations
that lead to wrong values.
Thanks Johannes for helping me figure this one out.
Cc: stable@kernel.org
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the introduction of the fixes for the
reorder timer, mac80211 will cause lockdep
warnings because lockdep confuses
local->skb_queue and local->rx_skb_queue
and treats their lock as the same.
However, their locks are different, and are
valid in different contexts (the former is
used in IRQ context, the latter in BH only)
and the only thing to be done is mark the
former as a different lock class so that
lockdep can tell the difference.
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Sujith <m.sujith@gmail.com>
Reported-by: Miles Lane <miles.lane@gmail.com>
Tested-by: Sujith <m.sujith@gmail.com>
Tested-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is defined in include/linux/ieee80211.h. As per IEEE spec.
bit6 to bit15 in block ack parameter represents buffer size.
So the bitmask should be 0xFFC0.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Cc: stable@kernel.org
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
