Note:
* At High Symbol Rates we do not have enouph machine cycles to handle the
incoming symbols and hence might run into problems at the very end of the
specified definition
* Most of the equations have been calculated for a master clock of 99 MHz,
running at 90MHz, raises lot of issues such as the need to recalculate
all of them , which is eventually very painful.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several chips may be turned off when the device is not used, like audio,
video and dvb demods. This patch adds a gpio callback at the core
structs to allow turning off such devices.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
A previous changeset moved gpio from em28xx struct into em28xx_board.
However, the driver were not updated to properly honor those gpio's.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before this patch, several devices without tuner were kept the value 0
for tuner_type. However, this means TUNER_TEMIC_PAL. Replace those
entries for the proper TUNER_ABSENT value.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Instead of a large, ugly switch specifying the gpio tables for each
device, let's move it into the boards struct. This also helps to see
what boards have already the gpio's for DVB.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Replaces all occurrences of em28xx_write_regs_req() and em28xx_write_reg()
used to setup register names by em28xx_write_reg().
Also, documents the register names that are known.
This patch were generated by this small perl script:
my %reg_map = (
# Register table - the same as defined on parse_em28xx.pl script
);
while (<>) {
if (m/(.*)em28xx_write_regs_req\(dev\,\s*0x00\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
my $reg = $2;
my $val = $3;
$val =~ tr/A-f/a-f/;
$reg = $reg_map{$reg} if defined($reg_map{$reg});
printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
} elsif (m/(.*)em28xx_write_regs\(dev\,\s*(.*)\,\s*\"\\x(..)\",\s*1\)\;(.*)/) {
my $reg = $2;
my $val = $3;
$val =~ tr/A-f/a-f/;
$reg = $reg_map{$reg} if defined($reg_map{$reg});
printf "$1em28xx_write_reg(dev, %s, 0x%s);$4\n", $reg, $val;
} else {
print $_;
}
}
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now, the first message states board names. Also, removed printing the alternate
settings by default. I2C messages are now clearer.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Since saa7115 has saa711x chip auto-detection, there's no need on differenciating
it at cards table. Just use the generic name for all boards that use a philips
saa711x decoder.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Several fields are duplicated on both structs. Let's just copy em28xx_board instead.
A later cleanup could just copy the fields that are changed, in order to keep em28xx_board
const.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove unused em28xx_board.vchannels and em28xx.video_channels.
Also, .is_em2800 = 0 is not needed, as all data is zeroed by kernel loader.
The table also included a notice that svideo weren't test on Hauppauge
USB2. Remove this notice, since this input also works properly.
Also, it does some whitespace cleanups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The previous patches removed XCLK and I2C magic. Now, we finally know
what those registers do. Also, only a very few cards need different
setups for those.
Instead of keeping the setups for those values inside the per-device
hack magic switch, move the uncommon values to the board-specific
struct, and have a common setup for all other boards.
So, almost 100 lines of hacking magic were removed.
A co-lateral effect of this patch is that it also fixes a bug at em28xx-core, where xclk
were set, without taking any care about not overriding a previous xclk setup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cleanup the calls to set the GPIOs and GPOs for various devices,
replacing the register number with the #define from em28xx-reg.h and
converting over to using em28xx_write_reg()
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert over to setting the XCLK register usage with the new em28xx_write_reg()
function.
Thanks to Ray Lu from Empia for providing the em2860/2880 datasheet.
Signed-off-by: Devin Heitmueller <devin.heitmueller@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch provides USB suspend and hibernation support
for Siano's SMS chipset based USB device
Signed-off-by: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Enable power LED while the frontend is in use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On some em28xx devices, there's an unused interface. This is printed on
the logs as an error. We can just ignore that interface.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The OmniVision OV534 is the USB bridge chip used in Sony Playstation EYE,
it is found also in other webcams like Hercules Blog Webcam and
Hercules Dualpix HD.
This driver is the port to gspca of a prototype driver by Mark Ferrell
based on vivi. The original code to initialize the camera and start the
capture is from Jim Paris on ps2dev.org, here integrated with the analysis
of the USB communications taken by the windows driver.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The sn9c105 and sn9c120 bridges must be differently programmed for the ov7660.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The msi gx7xx range of computers seem to be a strange lot with lots of different sys vendor names and differently oriented sensors. This commit adds another quirk for a range of them.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The gspca conversion deprecated a number of defines. Remove them.
Signed-off-by: Erik Andrén <erik.andren@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The bridge takes some time to update after a write, so apps doing a quick
write/read can get the old value back.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Currently the spca501 driver only works the first time used, then the cam needs
to be unplugged or the driver reloaded, this is because currently the data
which should be send each time the stream is started is send only once.
Likewise currently the data to initialize the cam is send from the probe
function, and thus will not get send after a suspend/resume.
This patch fixes this by sending both at the right time.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some webcams with image transfer by bulk messages accept one or many
permanent bulk read.
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The new exchanges are adapted from MS-win traces and the webcams work better.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The driver sn9c102 has no code for the ov7648 sensor.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
It is much more readable to swap the byteorder in the switch rather
than in each case statement.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
