79b42babba fixed identifying ATA devices
reporting 3c/c3 signature which belongs to SEMB devices now. However,
suspending the machine with such device (WDC WD2500AAJS-6 01.0) fails
with the following:
hda: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hda: UDMA/100 mode selected
hdb: host max PIO4 wanted PIO255(auto-tune) selected PIO4
hdb: UDMA/66 mode selected
sd 1:0:0:0: [sda] Starting disk
ata5: SATA link down (SStatus 0 SControl 300)
ata1: SATA link down (SStatus 0 SControl 300)
ata3: SATA link down (SStatus 0 SControl 300)
ata6: SATA link down (SStatus 0 SControl 300)
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata4: softreset failed (device not ready)
ata4: failed due to HW bug, retry pmp=0
ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2: limiting SATA link speed to 1.5 Gbps
ata4.00: configured for UDMA/133
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
ata2.00: class mismatch 1 != 7
ata2.00: revalidation failed (errno=-19)
ata2.00: disabled
sd 1:0:0:0: rejecting I/O to offline device
sd 1:0:0:0: [sda] START_STOP FAILED
sd 1:0:0:0: [sda] Result: hostbyte=0x01 driverbyte=0x00
PM: Device 1:0:0:0 failed to thaw: error 65536
sd 3:0:0:0: [sdb] Starting disk
due to a class mismatch in ata_dev_revalidate(). Fix it by adding the
ATA_DEV_SEMB device class to the check.
CC: Tejun Heo <htejun@gmail.com>
Signed-off-by: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Error timestamps are in jiffies which doesn't run while suspended and
PHY events during resume isn't too uncommon. When the two are
combined, it can lead to unnecessary speed downs if the machine is
suspended and resumed repeatedly. Clear error history on resume.
This was reported and verified in bnc#486803 by Vladimir Botka.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Vladimir Botka <vbotka@novell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The original driver doesn't use 66 MHz clock for UDMA33.
[ The alternative solution would be to adjust UDMA33 timings
for 66 MHz clock but I think that it is safer to stick with
old & tested behavior for now. ]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Marvell's new SoC (65 nano) needs different settings for its SATA
PHY registers.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
New device attach path in ata_eh_revalidate_and_attach() is divided
into two separate loops because ATA requires IDENTIFY to be issued to
slave first while the user expects to see device probe messages from
the master device. new_mask is used to track which devices are the
new ones between the first loop and the second.
This usually works well but if an error occurs during configuration
stage, ata_dev_revalidate_and_attach() returns with error code and
forgets new_mask. On the retry run, dev->class is set and new_mask
for the device is clear, so the device just gets revalidated and thus
ends up skipping post-configuration procedure including scheduling of
SCSI_HOTPLUG for the device. When this occurs, ATA part of probing
works fine but SCSI probing usually doesn't happen and makes the
device unreachable.
The behavior has been around for a very long time but it has been
uncovered with the recent addition of 1_5_GBPS horkage which uses
-EAGAIN return value from ata_dev_configure() to restart the probing
sequence after forcing cable speed.
This can be fixed by making sure dev->class is permanently set only
after all configurations are successfully complete. Fix it.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Tim Connors <tconnors+linuxkml@astro.swin.edu.au>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging-2.6:
Staging: comedi: David doesn't want to get comedi patches
Staging: rtl8187se: Fix compilation warnings and procfs directory leak
Staging: rt2870: new device id
Staging: w35und: unregister device from the ieee80211 stack upon ->disconnect()
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
usb-serial: ftdi_sio: fix reference counting of ftdi_private
USB: unusual_devs: extend nokia 6288 bcd range
USB: Gadget: fix UTF conversion in the usbstring library
USB: Fix makefile so that CONFIG_WDM and CONFIG_TMC work.
USB: ftdi_sio: add vendor/product id for the Marvell SheevaPlug
USB: cxacru: Fix negative dB output
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
Revert driver core: move platform_data into platform_device
Revert driver core: fix passing platform_data
Remove old PRINTK_DEBUG config item
Doc/sysfs-rules: Swap the order of the words so the sentence makes more sense
Driver core: platform: fix kernel-doc warnings
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6: (22 commits)
Fix the race between capifs remount and node creation
Fix races around the access to ->s_options
switch ufs directories to ufs_sync_file()
Switch open_exec() and sys_uselib() to do_open_filp()
Make open_exec() and sys_uselib() use may_open(), instead of duplicating its parts
Reduce path_lookup() abuses
Make checkpatch.pl shut up on fs/inode.c
NULL noise in fs/super.c:kill_bdev_super()
romfs: cleanup romfs_fs.h
ROMFS: romfs_dev_read() error ignored
fs: dcache fix LRU ordering
ocfs2: Use nd_set_link().
Fix deadlock in ipathfs ->get_sb()
Fix a leak in failure exit in 9p ->get_sb()
Convert obvious places to deactivate_locked_super()
New helper: deactivate_locked_super()
reiserfs: remove privroot hiding in lookup
reiserfs: dont associate security.* with xattr files
reiserfs: fixup xattr_root caching
Always lookup priv_root on reiserfs mount and keep it
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Fix line-in on Mac Mini Core2 Duo
ALSA: Release v1.0.20
sound: via82xx: fix DXS volume range
sound: serial-u16550: fix buffer overflow
ASoC: Fix errors in WM8990
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
bonding: fix panic if initialization fails
IXP4xx: complete Ethernet netdev setup before calling register_netdev().
IXP4xx: use "ENODEV" instead of "ENOSYS" in module initialization.
ipvs: Fix IPv4 FWMARK virtual services
ipv4: Make INET_LRO a bool instead of tristate.
net: remove stale reference to fastroute from Kconfig help text
net: update skb_recycle_check() for hardware timestamping changes
bnx2: Fix panic in bnx2_poll_work().
net-sched: fix bfifo default limit
igb: resolve panic on shutdown when SR-IOV is enabled
wimax: oops: wimax_dev_add() is the only one that can initialize the state
wimax: fix oops if netlink fails to add attribute
Bluetooth: Move dev_set_name() to a context that can sleep
netfilter: ctnetlink: fix wrong message type in user updates
netfilter: xt_cluster: fix use of cluster match with 32 nodes
netfilter: ip6t_ipv6header: fix match on packets ending with NEXTHDR_NONE
netfilter: add missing linux/types.h include to xt_LED.h
mac80211: pid, fix memory corruption
mac80211: minstrel, fix memory corruption
cfg80211: fix comment on regulatory hint processing
...
/home/v4l/master/v4l/cafe_ccic.c: In function 'cafe_cam_init':
/home/v4l/master/v4l/cafe_ccic.c:778: warning: statement with no effect
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: saeed bishara <saeed.bishara@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Due to an uninitialized chip.ident field the chip identification failed.
Thanks-to: Saeed Bishara <saeed.bishara@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
V4L2_TUNER_MODE_ was used in a few places where V4L2_TUNER_SUB_ should have
been used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Found the coccinelle tool.
Thanks-to: Julia Lawall <julia@diku.dk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The 2.6.30 kernel generates this warning:
uvc_driver.c:1729: warning: 'ret' may be used uninitialized in this function
I guess some new warning flag must have been turned on since this warning
didn't appear with older kernels (gcc version 4.3.1). It's also a bogus
warning, but since this code didn't comply to the coding standard anyway
I've modified it to 1) remove the warning and 2) conform to the coding
standard.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The boards control struct wasn't updated when (presumably) all of the
other drivers migrated from using scode_table to specifying the demod.
Signed-off-by: Steven Toth <stoth@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Some ioctls have structs that are a different size depending on what type
of buffer is being used. If the buffer type leaves a field unused or has
padding space at the end, this space should be zeroed out.
The problems with S_FMT and REQBUFS were original identified and patched by
Marton Nemeth <nm127@freemail.hu>.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
For a number of different ioctls, the v4l2-ioctl code checks that the
passed buffer type is supported by the driver. It did this by checking
that the driver defined a method for the try_fmt handler for that buffer
type. However, try_fmt is optional and a driver might not provide it even
though it does support that type. So use g_fmt instead, since that isn't
optional.
This should fix a problem with VBI capture with saa7146.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If someone requests a format at fmt->index == (unsigned)-1 and the first
format in the array doesn't have the requested type then num will still be
-1 when it's compared to fmt->index and there will appear to be a match.
Restructure the loop so this can't happen. It's simpler this way too. The
unnecessary check for (unsigned)fmt->index < 0 found by Roel Kluin
<roel.kluin@gmail.com> is removed this way too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Now urb buffers is not freed before suspend, so uvc_alloc_urb_buffers should
return packet counts allocated originally during uvc resume, instead of zero.
This version uses round down to return packet counts on Linus' suggestions,
or else may lead to buffer destructed if packet size is changed before
calling uvc_alloc_urb_buffers() in this kind of case.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@skynet.be>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If module initialisation failed (e.g. because the bonding sysfs entry
cannot be created), kernel panics:
IP: [<ffffffff8024910a>] destroy_workqueue+0x2d/0x146
Call Trace:
[<ffffffff808268c4>] bond_destructor+0x28/0x78
[<ffffffff80b64471>] netdev_run_todo+0x231/0x25a
[<ffffffff80b6dbcd>] rtnl_unlock+0x9/0xb
[<ffffffff81567907>] bonding_init+0x83e/0x84a
Remove the calls to bond_work_cancel_all() and destroy_workqueue();
both are also called/scheduled via bond_free_all().
bond_destroy_sysfs is unecessary because the sysfs entry has
not been created in the error case.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put generic_show_options read access to s_options under rcu_read_lock,
split save_mount_options() into "we are setting it the first time"
(uses in foo_fill_super()) and "we are relacing and freeing the old one",
synchronize_rcu() before kfree() in the latter.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Code Quality According To Mingo(tm) has been vastly improved,
no code has been damaged^Wchanged^Wdamaged.
[commit message rewritten -- AV]
Signed-off-by: Manish Katiyar <mkatiyar@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
There's no kernel-only content in it anymore, so move it to header-y
and remove the superflous #ifdef __KERNEL__.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
romfs_dev_read() may return -EIO, but ret is unsigned, so the errorpath
isn't taken.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Fix ordering of LRU when moving referenced dentries to the head of the list
(they should go to the head of the list in the same order as they were found
from the tail, rather than reverse order).
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
ocfs2 was hand-calling vfs_follow_link(), but there's no point to that.
Let's use page_follow_link_light() and nd_set_link().
Signed-off-by: Joel Becker <joel.becker@oracle.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Does equivalent of up_write(&s->s_umount); deactivate_super(s);
However, it does not does not unlock it until it's all over.
As the result, it's safe to use to dispose of new superblock on ->get_sb()
failure exits - nobody will see the sucker until it's all over.
Equivalent using up_write/deactivate_super is safe for that purpose
if superblock is either safe to use or has NULL ->s_root when we unlock.
Normally filesystems take the required precautions, but
a) we do have bugs in that area in some of them.
b) up_write/deactivate_super sequence is extremely common,
so the helper makes sense anyway.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
With Al Viro's patch to move privroot lookup to fs mount, there's no need
to have special code to hide the privroot in reiserfs_lookup.
I've also cleaned up the privroot hiding in reiserfs_readdir_dentry and
removed the last user of reiserfs_xattrs().
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The security.* xattrs are ignored for xattr files, so don't create them.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The xattr_root caching was broken from my previous patch set. It wouldn't
cause corruption, but could cause decreased performance due to allocating
a larger chunk of the journal (~ 27 blocks) than it would actually use.
This patch loads the xattr root dentry at xattr initialization and creates
it on-demand. Since we're using the cached dentry, there's no point
in keeping lookup_or_create_dir around, so that's removed.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
