Add support for 128-bit shared mailboxes found on Tegra234 chips.
Signed-off-by: Kartik <kkartik@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The list iterator is always non-NULL so it doesn't need to be checked.
Thus just remove the unnecessary NULL check.
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Smatch reports this issue
imx-mailbox.c:887:10: warning: Initializer entry defined twice
imx-mailbox.c:889:10: also defined here
.rxdb = imx_mu_generic_rxdb,
Is listed twice, so remove one.
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
During the system suspend path we must set all queues to operate in
polled mode as it is possible for any protocol built using this mailbox,
such as TISCI, to require communication during the no irq phase of suspend,
and we cannot rely on interrupts there.
Polled mode is implemented by allowing the mailbox user to define an
RX channel as part of the message that is sent which is what gets polled
for a response. If polled mode is enabled, this will immediately be
polled for a response at the end of the mailbox send_data op before
returning success for the data send or timing out if no response is
received.
Finally, to ensure polled mode is always enabled during system suspend,
iterate through all queues to set RX queues to polled mode during system
suspend and disable polled mode for all in the resume handler.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Refactor the portion of code that actually reads received messages from
a queue into its own function, ti_msgmgr_queue_rx_data, that is called
by the interrupt handler instead of reading directly from the handler.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX93 S401 MU support two interrupts: tx empty and rx full.
- Introduce a new flag IMX_MU_V2_IRQ for the dual interrupt case
- Update Copyright
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
To i.MX93 S401 MU, there are two interrupts: rx full and tx empty.
So extend irq to an array to prepare i.MX93 S401 MU support.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX8/8X SECO firmware IPC is an implementation of passing messages.
But current imx-mailbox driver only support one word message,
i.MX8/8X linux side firmware has to request four TX, four RX and a
TXDB to support IPC to SECO firmware. This is low efficent and
more interrupts triggered compared with one TX and one RX.
To make SECO MU work,
- parse the size of msg.
- Only enable TR0/RR0 interrupt for transmit/receive message.
- For TX/RX, only support one TX channel and one RX channel
- For RX, support receive msg of any size, limited by hardcoded value
of 30.
Signed-off-by: Franck LENORMAND <franck.lenormand@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add a rxdb callback to prepare for i.MX8 SECO MU rxdb which has a
different logic.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Mailbox driver needs to wait and read all the words in response to a
SCFW API call, else the protocol gets messed up and results in kernel hang.
When the responses are longer than 3 words its possible that SCFW will
take some time to fill up the rest of the words in the MU, a timeout of
100us is arbritrary and too short. While waiting for Linux to consume the
first 3 words of the response SCFW can be busy doing other stuff and hence
Linux needs to wait for the rest of the words.
Similar restriction applies when writing messages that are longer than
3 words.
This patch increases the timeout to 5secs while waiting for response
or writing long messages to SCFW.
Signed-off-by: Ranjani Vaidyanathan <ranjani.vaidyanathan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
check 'priv->clk' before 'imx_mu_read()' otherwise crash happens on
i.mx8ulp, since clock not enabled.
Fixes: 4f0b776ef5 ("mailbox: imx-mailbox: support i.MX8ULP MU")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Since IRQF_NO_SUSPEND used for imx mailbox driver, that means this irq
can't be used for wakeup source so that can't wakeup from freeze mode.
Add pm_system_wakeup() to wakeup from freeze mode.
Fixes: b7b2796b9b31e("mailbox: imx: ONLY IPC MU needs IRQF_NO_SUSPEND flag")
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch is to for MediaTek ADSP IPC mailbox controller driver
It is used to send short messages between processors with adsp
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Reviewed-by: YC Hung <yc.hung@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
MSM8976 APCS block is similar to one found in MSM8994.
Signed-off-by: Adam Skladowski <a39.skl@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The txdone can re-fill the mailbox. Keep polling the mailbox during the
flush until all the messages have been delivered.
This fixes an issue with the Tegra Combined UART (TCU) where output can
get truncated under high traffic load.
Signed-off-by: Pekka Pessi <ppessi@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Fixes: 91b1b1c3da ("mailbox: tegra-hsp: Add support for shared mailboxes")
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Treewide cleanup and consolidation of MSI interrupt handling in
preparation for further changes in this area which are necessary to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space
-----BEGIN PGP SIGNATURE-----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=vKzd
-----END PGP SIGNATURE-----
Merge tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull MSI irq updates from Thomas Gleixner:
"Rework of the MSI interrupt infrastructure.
This is a treewide cleanup and consolidation of MSI interrupt handling
in preparation for further changes in this area which are necessary
to:
- address existing shortcomings in the VFIO area
- support the upcoming Interrupt Message Store functionality which
decouples the message store from the PCI config/MMIO space"
* tag 'irq-msi-2022-01-13' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (94 commits)
genirq/msi: Populate sysfs entry only once
PCI/MSI: Unbreak pci_irq_get_affinity()
genirq/msi: Convert storage to xarray
genirq/msi: Simplify sysfs handling
genirq/msi: Add abuse prevention comment to msi header
genirq/msi: Mop up old interfaces
genirq/msi: Convert to new functions
genirq/msi: Make interrupt allocation less convoluted
platform-msi: Simplify platform device MSI code
platform-msi: Let core code handle MSI descriptors
bus: fsl-mc-msi: Simplify MSI descriptor handling
soc: ti: ti_sci_inta_msi: Remove ti_sci_inta_msi_domain_free_irqs()
soc: ti: ti_sci_inta_msi: Rework MSI descriptor allocation
NTB/msi: Convert to msi_on_each_desc()
PCI: hv: Rework MSI handling
powerpc/mpic_u3msi: Use msi_for_each-desc()
powerpc/fsl_msi: Use msi_for_each_desc()
powerpc/pasemi/msi: Convert to msi_on_each_dec()
powerpc/cell/axon_msi: Convert to msi_on_each_desc()
powerpc/4xx/hsta: Rework MSI handling
...
Use IRQF_NO_SUSPEND flag instead of enable_irq_wake to
support interrupt wake up from suspend.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Since hardware is supporting multiple IPCC instance,
use ipcc_%d instead of ipcc as the irq name to support
in driver.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Dynamic alloc for channel arrangement instead of static alloced
array, it is more flexible and can reduce memory usage.
Signed-off-by: Huang Yiwei <quic_hyiwei@quicinc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The Polarfire SoC is currently using two different compatible string
prefixes. Fix this by changing "polarfire-soc-*" strings to "mpfs-*" in
its system controller in order to match the compatible string used in
the soc binding and device tree.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Smatch static checker warns:
| drivers/mailbox/pcc.c:292 pcc_mbox_request_channel()
| error: uninitialized symbol 'dev'.
Fix the same by using pr_err instead of dev_err as the variable 'dev'
is uninitialized at that stage.
Fixes: ce028702dd ("mailbox: pcc: Move bulk of PCCT parsing into pcc_mbox_probe")
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix following coccicheck warning:
WARNING: Function "for_each_child_of_node"
should have of_node_put() before return.
Early exits from for_each_child_of_node should decrement the
node reference counter.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix following coccicheck warning:
WARNING: Function "for_each_available_child_of_node"
should have of_node_put() before return.
Early exits from for_each_available_child_of_node should decrement the
node reference counter.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The devm_kzalloc() function does not return error pointers, it returns
NULL on failure.
Fixes: 97961f78e8 ("mailbox: imx: support i.MX8ULP S4 MU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Convert hi3660 struct comments to kernel-doc notation and fix
other kernel-doc warnings:
drivers/mailbox/hi3660-mailbox.c:47: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Hi3660 mailbox channel information
drivers/mailbox/hi3660-mailbox.c:62: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* Hi3660 mailbox controller data
hi3660-mailbox.c:53: warning: contents before sections
hi3660-mailbox.c:67: warning: contents before sections
Fixes: 41c0e939d7 ("mailbox: Add support for Hi3660 mailbox")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Ruyi Wang <wangruyi@huawei.com>
Cc: Kaihua Zhong <zhongkaihua@huawei.com>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
To make sure the GCE request signal to SPM is not trigger by
other HW modules and cause suspend premature wake.
Set 0x7 (the bit 0~2 as 1) to GCE_GCTL_VALUE, to configure the
request signal control by SW and release the request to SPM.
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Silent the error if it's EPROBE_DEFER for clks.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Because mt8192 only have 1 gce, the gce_num should be 1.
Fixes: 85dfdbfc13 ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
As with other blocks, we intend to have drivers bind to generic
compatibles as long as there are no SoC-specific quirks. This allows
forward-compatibility with future SoCs.
No upstream DTs instantiate this yet, so it's still safe to make this
breaking change.
Signed-off-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
No point in retrieving the MSI descriptors. Just query the Linux interrupt
number.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211210221815.148331680@linutronix.de
Use the common msi_index member and get rid of the pointless wrapper struct.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20211210221814.413638645@linutronix.de
The driver uses irq_set_affinity_hint() to:
- Set the affinity_hint which is consumed by the userspace for
distributing the interrupts
- Enforce affinity
As per commit 6ac17fe8c1 ("mailbox: bcm-flexrm-mailbox: Set IRQ affinity
hint for FlexRM ring IRQs") the latter is done to ensure that the FlexRM
ring interrupts are evenly spread across all available CPUs. However, since
commit a0c9259dc4 ("irq/matrix: Spread interrupts on allocation") the
spreading of interrupts is dynamically performed at the time of allocation.
Hence, there is no need for the drivers to enforce their own affinity for
the spreading of interrupts.
Also, irq_set_affinity_hint() applying the provided cpumask as an affinity
for the interrupt is an undocumented side effect. To remove this side
effect irq_set_affinity_hint() has been marked as deprecated and new
interfaces have been introduced. Hence, replace the irq_set_affinity_hint()
with the new interface irq_update_affinity_hint() that only sets the
affinity_hint pointer.
Signed-off-by: Nitesh Narayan Lal <nitesh@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Link: https://lore.kernel.org/r/20210903152430.244937-11-nitesh@redhat.com
Like i.MX8 SCU, i.MX8ULP S4 also has vendor specific protocol.
- bind SCU/S4 MU part to share one tx/rx/init API to make code simple.
- S4 msg max size is very large, so alloc the space at driver probe,
not use local on stack variable.
- S4 MU has 8 TR and 4 RR which is different with i.MX8 MU, so adapt
code to reflect this.
Tested on i.MX8MP, i.MX8ULP
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Move the PCCT subspace parsing and allocation into pcc_mbox_probe so
that we can get rid of global PCC channel and mailbox controller data.
It also helps to make use of devm_* APIs for all the allocations.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
With all the plumbing in place to avoid accessing PCCT type and other
fields directly from the PCCT table all the time, let us now add the
support for extended PCC subspaces(type 3 and 4).
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
pcc_chan_reg_init now checks if the register bit width is within the
list [8, 16, 32, 64] and flags error if that is not the case. Therefore
there is no need to handling invalid bit-width in both read_register
and write_register. We can drop that along with the return values for
these 2 functions.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Now that the con_priv is availvale solely for PCC mailbox controller
driver, let us use the same to save the channel specific information
in it so that we can it whenever required instead of parsing the PCCT
table entries every time in both pcc_send_data and pcc_mbox_irq.
We can now use the newly introduces PCC register bundle to simplify both
saving of channel specific information and accessing them without repeated
checks for the subspace type.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Extended PCC subspaces introduces more registers into the PCCT. In order
to consolidate access to these registers and to keep all the details
contained in one place, let us introduce PCC register bundle that holds
the ACPI Generic Address Structure as well as the virtual address for
the same if it is mapped in the OS.
It also contains the various masks used to access the register and
the associated read, write and read-modify-write accessors.
We can also clean up the initialisations by having a helper function
for the same.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The specification refers this register and associated bitmask as platform
interrupt acknowledge register. Let us rename it so that it is easier to
map and understand.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Now that we have all the shared memory region information populated in
the pcc_mbox_chan, let us propagate the pointer to the same as the
return value to pcc_mbox_request channel.
This eliminates the need for the individual users of PCC mailbox to
parse the PCCT subspace entries and fetch the shmem information. This
also eliminates the need for PCC mailbox controller to set con_priv to
PCCT subspace entries. This is required as con_priv is private to the
controller driver to attach private data associated with the channel and
not meant to be used by the mailbox client/users.
Let us convert all the users of pcc_mbox_{request,free}_channel to use
new interface.
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Currently PCC mailbox controller sets con_priv in each channel to hold
the pointer to pcct subspace entry it corresponds to. The mailbox user
will then fetch this pointer from the channel descriptor they get when
they request for the channel. Using that pointer they then parse the
pcct entry again to fetch all the information about shared memory region.
In order to remove individual users of PCC mailbox parsing the PCCT
subspace entries to fetch same information, let us consolidate the same
in pcc mailbox controller by parsing all the shared memory region
information into a structure that can also hold the mbox_chan pointer it
represent.
This can then be used as main PCC mailbox channel pointer that we can
return as part of pcc_mbox_request_channel instead of standard mailbox
channel pointer.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Extended PCC subspaces(Type 3 and 4) differ from generic(Type 0) and
HW-Reduced Communication(Type 1 and 2) subspace structures. However some
fields share same offsets and same type of structure can be use to
extract the fields. In order to simplify that, let us move all the doorbell
register parsing into pcc_parse_subspace_db_reg and consolidate there.
It will be easier to extend it if required within the same.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Extended PCC subspaces(Type 3 and 4) differ from generic(Type 0) and
HW-Reduced Communication(Type 1 and 2) subspace structures. However some
fields share same offsets and same type of structure can be use to extract
the fields. In order to simplify that, let us move all the IRQ related
information parsing into pcc_parse_subspace_irq and consolidate there.
It will be easier to extend it if required within the same.
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Currently all the PCC channel specific information are stored/maintained
in global individual arrays for each of those information. It is not
scalable and not clean if we have to stash more channel specific
information. Couple of reasons to stash more information are to extend
the support to Type 3/4 PCCT subspace and also to avoid accessing the
PCCT table entries themselves each time we need the information.
This patch moves all those PCC channel specific information into a
separate structure pcc_chan_info.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Kernel doc validation script is unhappy and complains with the below set
of warnings.
| drivers/mailbox/pcc.c:179: warning: Function parameter or member 'irq'
| not described in 'pcc_mbox_irq'
| drivers/mailbox/pcc.c:179: warning: Function parameter or member 'p'
| not described in 'pcc_mbox_irq'
| drivers/mailbox/pcc.c:378: warning: expecting prototype for
| parse_pcc_subspaces(). Prototype was for parse_pcc_subspace() instead
Fix it.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Apple SoCs such as the M1 come with various co-processors. Mailboxes
are used to communicate with those. This driver adds support for
two variants of those mailboxes.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In the probe function, the clock IDs were pointed to local variables
which should only be used in the same code block, and any access to them
after the probing stage becomes an use-after-free case.
Since there are only limited variants of the gce clock names so far, we
can just declare them as static constants to fix the issue.
Fixes: 85dfdbfc13 ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
of_alias_get_id() may return -ENODEV which leads to illegal access to
the cmdq->clocks array.
Adding a check over alias_id to prevent the unexpected behavior.
Fixes: 85dfdbfc13 ("mailbox: cmdq: add multi-gce clocks support for mt8195")
Signed-off-by: Fei Shao <fshao@chromium.org>
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Because mtk_drm_crtc_update_config is not using cmdq_pkt_flush_async,
it won't have pkt->async_cb.cb anymore.
So remove the WARN_ON check of pkt->async_cb.cb at cmdq_exec_done.
Fixes: 1b6b0ce224 ("mailbox: mtk-cmdq: Use mailbox rx_callback")
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Enable QCM2290 APCS IPC support by adding the compatible. It reuses
msm8994_apcs_data.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The msm8994 type of apcs_data is defined multiple times with different
SoC name encoded. Consolidate them on msm8994 and remove the data
duplication.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the devm_platform_ioremap_resource() helper instead of
calling platform_get_resource() and devm_ioremap_resource()
separately
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
For the design of GCE hardware event signal transportation,
evnet rx will send the event signal to all GCE event merges
after receiving the event signal from the other hardware.
Because GCE event merges need to response to event rx, their
clocks must be enabled at that time.
To make sure all the gce clock is enabled while receiving the
hardware event, each cmdq mailbox should enable or disable
the others gce clk at the same time.
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add mt8195 compatible name in the driver data of cmdq mailbox driver.
Signed-off-by: jason-jh.lin <jason-jh.lin@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
MSM8953 has an APCS block similar to MSM8916 but with different clocks
which are spread over 2MB IO region next to it.
Signed-off-by: Vladimir Lypak <junak.pub@gmail.com>
Signed-off-by: Sireesh Kodali <sireeshkodali@protonmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Qcom SM4250/6115, have APCS mailbox setup similar to msm8998 and
msm8916.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch enables the qcom_ipcc driver to be loaded as a
module. IPCC is fairly core to system, so as such it should
never be unloaded. It registers as a mailbox + irq controller
and the irq controller drivers in kernel are not supposed to
be unloaded as they don't have the visibility over the clients
consuming the irqs. Hence adding supress_bind_attrs to disable
bind/unbind via sysfs.
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use kernel-doc struct notation for the mailbox structs to prevent
these kernel-doc warnings:
drivers/mailbox/mailbox-sti.c:39: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* STi Mailbox device data
drivers/mailbox/mailbox-sti.c:63: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* STi Mailbox platform specific configuration
drivers/mailbox/mailbox-sti.c:74: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* STi Mailbox allocated channel information
Also move the field descriptions ahead of the function description as
is expected in kernel-doc. This prevents another kernel-doc warning.
Fixes: 9ef4546cbd ("mailbox: Add support for ST's Mailbox IP")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Cc: Aditya Srivastava <yashsri421@gmail.com>
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This driver adds support for the single mailbox channel of the MSS
system controller on the Microchip PolarFire SoC.
Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Clang warns:
drivers/mailbox/imx-mailbox.c:284:2: warning: variable 'val' is used
uninitialized whenever switch default is taken
[-Wsometimes-uninitialized]
default:
^~~~~~~
drivers/mailbox/imx-mailbox.c:288:7: note: uninitialized use occurs here
if (!val)
^~~
drivers/mailbox/imx-mailbox.c:263:9: note: initialize the variable 'val'
to silence this warning
u32 val, ctrl;
^
= 0
1 warning generated.
Prior to commit 91c8c1fbe498 ("mailbox: imx: add xSR/xCR register
array"), val was always initialized in imx_mu_isr() but now, it is not
initialized in the default case. Return IRQ_NONE like the statement
below does and add a message that there is an unhandled type for this
switch statement so that it can be updated.
Fixes: 91c8c1fbe498 ("mailbox: imx: add xSR/xCR register array")
Link: https://github.com/ClangBuiltLinux/linux/issues/1404
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Enable MSM8939 APCS support by adding the compatible. It reuses
msm8916_apcs_data.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In adding APCS clock support for MSM8939, the second clock registration
fails due to duplicate device name like below.
[ 0.519657] sysfs: cannot create duplicate filename '/bus/platform/devices/qcom-apcs-msm8916-clk'
...
[ 0.661158] qcom_apcs_ipc b111000.mailbox: failed to register APCS clk
This is because MSM8939 has 3 APCS instances for Cluster0 (little cores),
Cluster1 (big cores) and CCI (Cache Coherent Interconnect). Although
only APCS of Cluster0 and Cluster1 have IPC bits, each of 3 APCS has
A53PLL clock control bits. That said, 3 'qcom-apcs-msm8916-clk' devices
need to be registered to instantiate all 3 clocks. Use PLATFORM_DEVID_AUTO
rather than PLATFORM_DEVID_NONE for platform_device_register_data() call
to fix the issue above.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This commit adds compatible for the SM6125 SoC
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The "cb" pointer needs to be initialized before can assign
"data.data = cb->data;".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix IPCC (Inter-Processor Communication Controller) channel exhaustion by
setting the channel private data to NULL on mbox shutdown.
Err Logs:
remoteproc: MBA booted without debug policy, loading mpss
remoteproc: glink-edge: failed to acquire IPC channel
remoteproc: failed to probe subdevices for remoteproc: -16
Fixes: fa74a0257f ("mailbox: Add support for Qualcomm IPCC")
Signed-off-by: Sibi Sankar <sibis@codeaurora.org>
Cc: stable@vger.kernel.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Current client use 'struct cmdq_pkt' as callback data, so
change 'void *data' to 'struct cmdq_pkt *pkt'. Keep data
until client use pkt instead of data.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
rx_callback is a standard mailbox callback mechanism and could cover the
function of proprietary cmdq_task_cb, so use the standard one instead of
the proprietary one. But the client driver has already used cmdq_task_cb,
so keep cmdq_task_cb until all client driver use rx_callback instead of
cmdq_task_cb.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
cmdq_cb_status is an error status. Use the standard error number
instead of cmdq_cb_status to prevent status duplication.
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Reviewed-by: Yongqiang Niu <yongqiang.niu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX8ULP MU has different register layout and bit layout compared
with i.MX6SX/7ULP/8.
So add enum imx_mu_type to show it is IMX_MU_V2 or IMX_MU_V1.
For IMX_MU_V2 mu hardware, check it when calculating bit offset to get
the correct offset.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
We are going to add a new platform which has 4 status registers(SR, TSR,
RSR, GSR) and 4 control registers(CR, TCR, RCR, GCR), so extend xSR
and xCR to register array and adapt code to use it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The xTR/xRR registers are using 4 bytes stride and continuous.
Considering we will support more TR and RR registers, use base + idx * 4
method to calculate register address, not hardcoding in driver.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
s/Hisilicon/HiSilicon/.
It should use capital S, according to
https://www.hisilicon.com/en.
Signed-off-by: Hao Fang <fanghao11@huawei.com>
Reviewed-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
When devm_ioremap_resource() fails, a clear enough error message will be
printed by its subfunction __devm_ioremap_resource(). The error
information contains the device name, failure cause, and possibly resource
information.
Therefore, remove the error printing here to simplify code and reduce the
binary size.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Qiheng Lin <linqiheng@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some sensors connected to Unisoc mailbox will send data very frequently.
This makes channel 0 very busy and the messages from other remote cores
not able to be handled as soon as possible.
It's a trick (un-documented) from Unisoc ASIC designers to resolve this
special requirement that an inbox assigned to one of the remote cores
before was modified to be exposed to host cpu core.
Then from host side, a supplementary inbox is added for transferring mass
but not emergency messages from the remote cores, such as step counting
sensor, with an independent FIFO and interrupt which is as same as channel
0. Meanwihle, inbox part of this channel is still kept for original remote
core to use.
Signed-off-by: Orson Zhai <orson.zhai@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Unisoc mailbox has no way to be enabled/disabled for any single channel.
They can only be set to startup or shutdown as a whole device at same time.
Add a variable to count references to avoid mailbox FIFO being reset
unexpectedly when clients are requesting or freeing channels.
Also add a lock to dismiss possible conflicts from register r/w in
different startup or shutdown threads. And fix the crash problem when early
interrupts come from channel which has not been requested by client yet.
Fixes: ca27fc26cd ("mailbox: sprd: Add Spreadtrum mailbox driver")
Signed-off-by: Orson Zhai <orson.zhai@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
./drivers/mailbox/pcc.c:580:3-8: No need to set .owner here. The core
will do it.
Remove .owner field if calls are used which set it automatically
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Change my e-mail address to kabel@kernel.org, and fix my name in
non-code parts (add diacritical mark).
Link: https://lkml.kernel.org/r/20210325171123.28093-2-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It is possible that 'data' passed to kfree() is set to a error value
instead of allocated space. Make sure it doesn't get called with invalid
pointer.
Fixes: 5a6338cce9 ("mailbox: arm_mhuv2: Add driver")
Cc: v5.11 <stable@vger.kernel.org> # v5.11
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
On Tegra194, due to both BPMP and TCU using mailboxes, we get a
lockdep spew at boot. Both are using different instances of HSP,
so this is harmless. As such give each HSP instance a different
lockdep class.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
According to the specification, bit[2] represents SPRD_OUTBOX_FIFO_FULL,
not bit[0], so correct it.
Fixes: ca27fc26cd ("mailbox: sprd: Add Spreadtrum mailbox driver")
Signed-off-by: Magnum Shan <magnum.shan@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Baolin Wang <baolin.wang7@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
My build tests failed to catch that amba driver that would have needed
adaption in commit 3fd269e74f ("amba: Make the remove callback return
void"). Change the remove function to make the driver build again.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 3fd269e74f ("amba: Make the remove callback return void")
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In SDX55, the IPC bits are located in the APCS GCC block. Also, this block
can provide clock functionality. Hence, add support for IPC with correct
offset and name of the clock provider.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The AM64x SoC contains a Mailbox IP instance with multiple clusters
in the MAIN domain, and is a variant of the IP on current AM65x and
J721E SoCs. The AM64x SoC has only 8 clusters with no interrupts
routed to the A53 core on the first 2 clusters. The interrupt outputs
from the IP do not go through any Interrupt Routers and are hard-wired
to each processor, with only couple of interrupts from each cluster
reaching the A53 core. The IP is also not built with the K3 safety
feature in hardware.
Add the support for this IP through a new compatible.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The Qualcomm SC8180X platform has a APSS block exposing the usual IPC
bits, add a compatible for this.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This adds driver for the ARM MHUv2 (Message Handling Unit) mailbox
controller.
This is based on the accepted DT bindings of the controller and supports
combination of both transport protocols, i.e. doorbell and data-transfer.
Transmitting and receiving data through the mailbox framework is done
through struct arm_mhuv2_mbox_msg.
Based on the initial work done by Morten Borup Petersen from ARM.
Co-developed-by: Tushar Khandelwal <tushar.khandelwal@arm.com>
Signed-off-by: Tushar Khandelwal <tushar.khandelwal@arm.com>
Tested-by: Usama Arif <usama.arif@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Now that the driver can be enabled by COMPILE_TEST, we see warnings on
64bit platforms when void pointers are cast to unsigned int (and
vice versa).
warning: cast to smaller integer type 'unsigned int' from 'void *'
unsigned int chan = (unsigned int)link->con_priv;
...
warning: cast to 'void *' from smaller integer type 'unsigned int'
ipcc->controller.chans[i].con_priv = (void *)i;
Update these casts to use unsigned long variables, which are the same
size as pointers on all platforms.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
platform_get_irq_byname already prints an error message if the requested
irq was not found. Don't print another message in the driver.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This allows compiling the driver on architectures where the hardware is not
available. Most other mailbox drivers support this as well.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The mhu_db_channel info is allocated per channel using devm_kzalloc from
mhu_db_mbox_xlate which gets called from mbox_request_channel. However
we are releasing the allocated mhu_db_channel info using plain kfree from
mhu_db_shutdown which is called from mbox_free_channel.
This leads to random crashes when the channel is freed like below one:
Unable to handle kernel paging request at virtual address 0080000400000008
[0080000400000008] address between user and kernel address ranges
Internal error: Oops: 96000044 [#1] PREEMPT SMP
Modules linked in: scmi_module(-)
CPU: 1 PID: 2212 Comm: rmmod Not tainted 5.10.0-rc5 #31
Hardware name: ARM LTD ARM Juno Development Platform/ARM Juno
Development Platform, BIOS EDK II Nov 19 2020
pstate: 20000085 (nzCv daIf -PAN -UAO -TCO BTYPE=--)
pc : release_nodes+0x74/0x230
lr : devres_release_all+0x40/0x68
Call trace:
release_nodes+0x74/0x230
devres_release_all+0x40/0x68
device_release_driver_internal+0x12c/0x1f8
driver_detach+0x58/0xe8
bus_remove_driver+0x64/0xe0
driver_unregister+0x38/0x68
platform_driver_unregister+0x1c/0x28
scmi_driver_exit+0x38/0x44 [scmi_module]
__arm64_sys_delete_module+0x188/0x260
el0_svc_common.constprop.0+0x80/0x1a8
do_el0_svc+0x2c/0x98
el0_sync_handler+0x160/0x168
el0_sync+0x174/0x180
Code: 1400000d eb07009f 54000460 f9400486 (f90004a6)
---[ end trace c55ffd306c140233 ]---
Fix it by replacing kfree with devm_kfree as required.
Fixes: 7002ca237b ("mailbox: arm_mhu: Add ARM MHU doorbell driver")
Reported-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Cristian Marussi <cristian.marussi@arm.com>
Reviewed-by: Cristian Marussi <cristian.marussi@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Various driver updates for platforms. A bulk of this is smaller fixes or
cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs
and platforms.
-----BEGIN PGP SIGNATURE-----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=tfPb
-----END PGP SIGNATURE-----
Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms. A bulk of this is smaller fixes
or cleanups, but some of the new material this time around is:
- Support for Nvidia Tegra234 SoC
- Ring accelerator support for TI AM65x
- PRUSS driver for TI platforms
- Renesas support for R-Car V3U SoC
- Reset support for Cortex-M4 processor on i.MX8MQ
There are also new socinfo entries for a handful of different SoCs and
platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (131 commits)
drm/mediatek: reduce clear event
soc: mediatek: cmdq: add clear option in cmdq_pkt_wfe api
soc: mediatek: cmdq: add jump function
soc: mediatek: cmdq: add write_s_mask value function
soc: mediatek: cmdq: add write_s value function
soc: mediatek: cmdq: add read_s function
soc: mediatek: cmdq: add write_s_mask function
soc: mediatek: cmdq: add write_s function
soc: mediatek: cmdq: add address shift in jump
soc: mediatek: mtk-infracfg: Fix kerneldoc
soc: amlogic: pm-domains: use always-on flag
reset: sti: reset-syscfg: fix struct description warnings
reset: imx7: add the cm4 reset for i.MX8MQ
dt-bindings: reset: imx8mq: add m4 reset
reset: Fix and extend kerneldoc
reset: reset-zynqmp: Added support for Versal platform
dt-bindings: reset: Updated binding for Versal reset driver
reset: imx7: Support module build
soc: fsl: qe: Remove unnessesary check in ucc_set_tdm_rxtx_clk
soc: fsl: qman: convert to use be32_add_cpu()
...
If the txdone is done by polling, it is possible for msg_submit() to start
the timer while txdone_hrtimer() callback is running. If the timer needs
recheduling, it could already be enqueued by the time hrtimer_forward_now()
is called, leading hrtimer to loudly complain.
WARNING: CPU: 3 PID: 74 at kernel/time/hrtimer.c:932 hrtimer_forward+0xc4/0x110
CPU: 3 PID: 74 Comm: kworker/u8:1 Not tainted 5.9.0-rc2-00236-gd3520067d01c-dirty #5
Hardware name: Libre Computer AML-S805X-AC (DT)
Workqueue: events_freezable_power_ thermal_zone_device_check
pstate: 20000085 (nzCv daIf -PAN -UAO BTYPE=--)
pc : hrtimer_forward+0xc4/0x110
lr : txdone_hrtimer+0xf8/0x118
[...]
This can be fixed by not starting the timer from the callback path. Which
requires the timer reloading as long as any message is queued on the
channel, and not just when current tx is not done yet.
Fixes: 0cc67945ea ("mailbox: switch to hrtimer for tx_complete polling")
Reported-by: Da Xue <da@libre.computer>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Tested-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Tested-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
platform_get_irq() returns -ERRNO on error. In such case casting to u32
and comparing to 0 would pass the check.
Fixes: 623a6143a8 ("mailbox: mediatek: Add Mediatek CMDQ driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The MHU drives the signal using a 32-bit register, with all 32 bits
logically ORed together. The MHU provides a set of registers to enable
software to set, clear, and check the status of each of the bits of this
register independently. The use of 32 bits for each interrupt line
enables software to provide more information about the source of the
interrupt. For example, each bit of the register can be associated with
a type of event that can contribute to raising the interrupt.
This patch adds a separate the MHU controller driver for doorbel mode
of operation using the extended DT binding to add support the same.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Since we will be soon adding a separate driver based on this ARM MHU
driver to support doorbell mode, let us add explicit check to match
the default compatible for this driver. This is needed as the probe
and match reuses the AMBA device ids currently and don't have any
explicit compatible check.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Enable support for the BPMP on Tegra234 to avoid relying on Tegra194
being enabled to pull in the needed OF device ID table entry.
On simulation platforms the BPMP hasn't booted up yet by the time we
probe the BPMP driver and the BPMP hasn't had a chance to mark the
doorbell as ringable by the CCPLEX. This corresponding check in the
BPMP driver will therefore fail. Work around this by disabling the
check on simulation platforms.
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Patch series "iomap: Constify ioreadX() iomem argument", v3.
The ioread8/16/32() and others have inconsistent interface among the
architectures: some taking address as const, some not.
It seems there is nothing really stopping all of them to take pointer to
const.
This patch (of 4):
The ioreadX() and ioreadX_rep() helpers have inconsistent interface. On
some architectures void *__iomem address argument is a pointer to const,
on some not.
Implementations of ioreadX() do not modify the memory under the address so
they can be converted to a "const" version for const-safety and
consistency among architectures.
[krzk@kernel.org: sh: clk: fix assignment from incompatible pointer type for ioreadX()]
Link: http://lkml.kernel.org/r/20200723082017.24053-1-krzk@kernel.org
[akpm@linux-foundation.org: fix drivers/mailbox/bcm-pdc-mailbox.c]
Link: http://lkml.kernel.org/r/202007132209.Rxmv4QyS%25lkp@intel.com
Suggested-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Rich Felker <dalias@libc.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Allen Hubbe <allenbh@gmail.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Link: http://lkml.kernel.org/r/20200709072837.5869-1-krzk@kernel.org
Link: http://lkml.kernel.org/r/20200709072837.5869-2-krzk@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Do success callback in channel when shutdown. For those task not finish,
callback with error code thus client has chance to cleanup or reset.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add gce v4 hardware support with different thread number and shift.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some gce hardware shift pc and end address in register to support
large dram addressing.
Implement gce address shift when write or read pc and end register.
And add shift bit in platform definition.
Signed-off-by: Dennis YC Hsieh <dennis-yc.hsieh@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
MSM8994 has an APCS block similar to 8916, but
with a different clock driver due to the former
one having 2 clusters.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The Qualcomm SDM660 platform has a APCS HMSS GLOBAL block, add the
compatible for this.
Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
When CONFIG_PM and CONFIG_PM_SLEEP are unset, the following warnings
occur:
drivers/mailbox/imx-mailbox.c:638:12: warning: 'imx_mu_runtime_resume'
defined but not used [-Wunused-function]
638 | static int imx_mu_runtime_resume(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~
drivers/mailbox/imx-mailbox.c:629:12: warning: 'imx_mu_runtime_suspend'
defined but not used [-Wunused-function]
629 | static int imx_mu_runtime_suspend(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~~~
drivers/mailbox/imx-mailbox.c:611:12: warning: 'imx_mu_resume_noirq'
defined but not used [-Wunused-function]
611 | static int imx_mu_resume_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~
drivers/mailbox/imx-mailbox.c:601:12: warning: 'imx_mu_suspend_noirq'
defined but not used [-Wunused-function]
601 | static int imx_mu_suspend_noirq(struct device *dev)
| ^~~~~~~~~~~~~~~~~~~~
Mark these functions as __maybe_unused, which is the standard procedure
for PM functions.
Fixes: bb2b2624db ("mailbox: imx: Add runtime PM callback to handle MU clocks")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The acpi_get_table() should be coupled with acpi_put_table() if
the mapped table is not used at runtime to release the table
mapping.
In acpi_pcc_probe(), the PCCT table entries will be used as private
data for communication chan at runtime, but the table should be put
for error path.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The Qualcomm ipq6018 has apcs block, add compatible for the same. Also,
the ipq6018 apcs provides a clock functionality similar to msm8916 but
the clock driver is different.
Create a child device based on the apcs compatible for the clock
controller functionality.
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some apcs mailbox devices supports a clock driver, the compatible
strings of devices supporting clock driver along with the clock driver
name are maintained in a separate structure within the mailbox driver.
And the clock driver is added based on device match.
With increase in number of devices supporting the clock feature move the
clock driver name inside the driver data. so that we can use a single
API to get the register offset of mailbox driver and clock driver name
together, and the clock driver will be added based on the driver data.
Signed-off-by: Sivaprakash Murugesan <sivaprak@codeaurora.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
IPC MU has no power domain assigned and there could be IPC during
noirq suspend phase, so IRQF_NO_SUSPEND flag is needed for IPC MU.
However, for other MUs, they have power domain assigned and their
power will be turned off during noirq suspend phase, but with
IRQF_NO_SUSPEND set, their interrupts are NOT disabled even after
their power turned off, it will cause system crash when mailbox
driver trys to handle pending interrupts but the MU power is already
turned off.
So, IRQF_NO_SUSPEND flag should ONLY be added to IPC MU which has
power domain managed by SCU, then all other MUs' pending interrupts
after noirq suspend phase will be handled after system resume.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some of i.MX8M SoCs have MU clock, they need to be managed in runtime
to make sure the MU clock can be off in runtime, add runtime PM callback
to handle MU clock.
And on i.MX8MP, the MU clock is combined with power domain and runtime
PM is enabled for the clock driver, during noirq suspend/resume phase,
runtime PM is disabled by device suspend, but the MU context save/restore
needs to enable MU clock for register access, calling clock prepare/enable
will trigger runtime resume failure and lead to system suspend failed.
Actually, the MU context save/restore is ONLY necessary for SCU IPC MU,
other MUs especially on i.MX8MP platforms which have MU clock assigned,
they need to runtime request/free mailbox channel in the consumer driver,
so no need to save/restore MU context for them, hence it can avoid this
issue, so the MU context save/restore is ONLY applied to i.MX platforms
MU instance without clock present.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
For "mem" mode suspend on i.MX8 SoCs, MU settings could be
lost because its power is off, so save/restore is needed
for MU settings during suspend/resume. However, the restore
can ONLY be done when MU settings are actually lost, for the
scenario of settings NOT lost in "freeze" mode suspend, since
there could be still IPC going on multiple CPUs, restoring the
MU settings could overwrite the TIE by mistake and cause system
freeze, so need to make sure ONLY restore the MU settings when
it is powered off, Anson fixes this by checking whether restore
is actually needed when resume.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add support for the Inter-Processor Communication Controller (IPCC)
block from Qualcomm that coordinates the interrupts (inbound & outbound)
for Multiprocessor (MPROC), COMPUTE-Level0 (COMPUTE-L0) & COMPUTE-Level1
(COMPUTE-L1) protocols for the Application Processor Subsystem (APSS).
This driver is modeled as an irqchip+mailbox driver. The irqchip part
helps in receiving the interrupts from the IPCC clients such as modems,
DSPs, PCI-E etc... and forwards them to respective entities in APSS.
On the other hand, the mailbox part is used to send interrupts to the IPCC
clients from the entities of APSS.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Raghavendra Rao Ananta <rananta@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[mani: moved to mailbox, added static mbox channels and cleanups]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). So we should check whether the return value of devm_ioremap()
is NULL instead of IS_ERR.
Fixes: 4981b82ba2 ("mailbox: ZynqMP IPI mailbox controller")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The i.MX8 SCU message header size is the number of "u32" elements,
not "u8", so fix the check.
Reported-by: coverity-bot <keescook+coverity-bot@chromium.org>
Addresses-Coverity-ID: 1461658 ("Memory - corruptions")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The Spreadtrum mailbox controller supports 8 channels to communicate
with MCUs, and it contains 2 different parts: inbox and outbox, which
are used to send and receive messages by IRQ mode.
Signed-off-by: Baolin Wang <baolin.wang@unisoc.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The function platform_get_irq can log an error already.
Thus omit a redundant message for the exception handling in the
calling function.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
devm_mbox_controller_register() may fail, and in the case of failure the
priv->clk clock that was previously enabled, should be disabled.
Fixes: 2bb7005696 ("mailbox: Add support for i.MX messaging unit")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
[Jassi: fixed merge/am conflict]
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This called from mbox_request_channel(). The caller is expecting error
pointers and not NULL so this "return NULL;" will lead to an Oops.
Fixes: 0a67003b19 ("mailbox: imx: add SCU MU support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Some power hungry sub-systems like VPU has its own MUs which also
use mailbox driver, current mailbox driver uses platform driver
model and MU's power will be ON after driver probed and left ON
there, it may cause the whole sub-system can NOT enter lower power
mode, take VPU driver for example, it has runtime PM support, but
due to its MU always ON, the VPU sub-system will be always ON and
consume many power during kernel idle.
To save power in kernel idle, mailbox driver needs to support
runtime PM in order to power off MU when it is unused. However,
the runtime suspend/resume can ONLY be implemented in mailbox's
.shutdown/.startup callback, so its consumer needs to call
mbox_request_channel()/mbox_free_channel() in consumer driver's
runtime PM callback, then the MU's power will be ON/OFF along with
consumer's runtime PM status.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Fix the following sparse warning:
drivers/mailbox/pcc.c:571:24: warning: symbol 'pcc_mbox_driver' was not
declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
i.MX8/8X SCU MU is dedicated for communication between SCU and Cortex-A
cores from hardware design, and could not be reused for other purpose.
Per i.MX8/8X Reference mannual, Chapter "12.9.2.3.2 Messaging Examples",
Passing short messages: Transmit register(s) can be used to pass
short messages from one to four words in length. For example, when
a four-word message is desired, only one of the registers needs to
have its corresponding interrupt enable bit set at the receiver side;
the message’s first three words are written to the registers whose
interrupt is masked, and the fourth word is written to the other
register (which triggers an interrupt at the receiver side).
i.MX8/8X SCU firmware IPC is an implementation of passing short
messages. But current imx-mailbox driver only support one word
message, i.MX8/8X linux side firmware has to request four TX
and four RX to support IPC to SCU firmware. This is low efficent
and more interrupts triggered compared with one TX and
one RX.
To make SCU MU work,
- parse the size of msg.
- Only enable TR0/RR0 interrupt for transmit/receive message.
- For TX/RX, only support one TX channel and one RX channel
- For RX, support receive msg larger than 4 u32 words.
- Support 6 channels, TX0/RX0/RXDB[0-3], not support TXDB.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add imx_mu_generic_tx for data send and imx_mu_generic_rx for interrupt
data receive.
Pack original mu chans related code into imx_mu_init_generic
Add tx/rx/init hooks into imx_mu_dcfg
With these, it will be a bit easy to introduce i.MX8/8X SCU type
MU dedicated to communicate with SCU.
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
After implement flush, client can flush the executing
command buffer or abort the still waiting for event
command buffer, so controller do not need to implement
atomic_exe feature. remove it.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
For client driver which need to reorganize the command buffer, it could
use this function to flush the send command buffer.
If the channel doesn't be started (usually in waiting for event), this
function will abort it directly.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Allwinner sun6i, sun8i, sun9i, and sun50i SoCs contain a hardware
message box used for communication between the ARM CPUs and the ARISC
management coprocessor. This mailbox contains 8 unidirectional
4-message FIFOs.
Add a driver for it, so it can be used with the Linux mailbox framework.
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Since snprintf() returns the would-be-output size instead of the
actual output size, the succeeding calls may go beyond the given
buffer limit. Fix it by replacing with scnprintf().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
In this function,we don't need dev_err() message because when something
goes wrong,platform_get_irq() and devm_platform_ioremap_resource() have
print an error message itself, so we should remove duplicate dev_err().
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use devm_platform_ioremap_resource() to simplify code.
Signed-off-by: Yangtao Li <tiny.windzz@gmail.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
- omap : misc - catch error returned from pm_runtime_put_sync
- hisi : misc - drop .owner from platform_driver
- stm : change how wakeup is handled
- imx : fix - bailout on error and nuke correct irq
- imx : add support for imx7ulp platform
-----BEGIN PGP SIGNATURE-----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=KJ0/
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v5.5' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- omap : misc - catch error returned from pm_runtime_put_sync
- hisi : misc - drop .owner from platform_driver
- stm : change how wakeup is handled
- imx : fix - bailout on error and nuke correct irq
- imx : add support for imx7ulp platform
* tag 'mailbox-v5.5' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: imx: add support for imx v1 mu
dt-bindings: mailbox: imx-mu: add imx7ulp MU support
mailbox: imx: Clear the right interrupts at shutdown
mailbox: imx: Fix Tx doorbell shutdown path
mailbox: stm32-ipcc: Update wakeup management
mailbox: no need to set .owner platform_driver_register
mailbox/omap: Handle if CONFIG_PM is disabled
There is a version 1.0 MU on i.MX7ULP platform.
One new version ID register is added, and it's offset is 0.
TRn registers are defined at the offset 0x20 ~ 0x2C.
RRn registers are defined at the offset 0x40 ~ 0x4C.
SR/CR registers are defined at 0x60/0x64.
Extend this driver to support it.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Make sure to only clear enabled interrupts keeping count
of the connection type.
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The wakeup specific IRQ management is no more needed to wake up the
stm32 platform. A relationship has been established between the EXTI and
the RX IRQ, just need to declare the EXTI interrupt instead of the
IPCC RX IRQ.
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
the platform_driver_register will set the .owner to THIS_MODULE
Signed-off-by: Tian Tao <tiantao6@huawei.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Commit 7723f4c5ec ("driver core: platform: Add an error message to
platform_get_irq*()") added an error message to avoid drivers having
to print an error message when IRQ lookup fails. However, there are
some cases where IRQs are optional and so new optional versions of
the platform_get_irq*() APIs have been added for these cases.
The IRQs for Tegra HSP module are optional because not all instances
of the module have the doorbell and all of the shared interrupts.
Hence, since the above commit was applied the following error messages
are now seen on Tegra194 ...
ERR KERN tegra-hsp c150000.hsp: IRQ doorbell not found
ERR KERN tegra-hsp c150000.hsp: IRQ shared0 not found
The Tegra HSP driver deliberately does not fail if these are not found
and so fix the above errors by updating the Tegra HSP driver to use
the platform_get_irq_byname_optional() API.
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20191011083459.11551-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mailbox length is 0x1000 hence the max_register value is 0xFFC.
Fixes: c6a8b171ca ("mailbox: qcom: Convert APCS IPC driver to use
regmap")
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add support of IPQ8074 with IPC register offset as 8.
Signed-off-by: Gokul Sriram Palanisamy <gokulsri@codeaurora.org>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
There is clock controller functionality in the APCS hardware block of
qcs404 devices similar to msm8916.
Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
GCE hardware stored event information in own internal sysram,
if the initial value in those sysram is not zero value
it will cause a situation that gce can wait the event immediately
after client ask gce to wait event but not really trigger the
corresponding hardware.
In order to make sure that the wait event function is
exactly correct, we need to clear the sysram value in
cmdq initial flow.
Fixes: 623a6143a8 ("mailbox: mediatek: Add Mediatek CMDQ driver")
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
add mt8183 compatible name for supporting gce function
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The interrupt mask and thread number has positive correlation,
so we move the CMDQ_IRQ_MASK into cmdq driver data and calculate
it by thread number.
Signed-off-by: Bibby Hsieh <bibby.hsieh@mediatek.com>
Reviewed-by: CK Hu <ck.hu@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use devm_mbox_controller_register to get rid of
redundant remove function.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups. Because of this, there is going
to be some merge issues with your tree at the moment, I'll follow up
with the expected resolutions to make it easier for you.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups (will cause build warnings
with s390 and coresight drivers in your tree)
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse
easier due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of merge
issues that Stephen has been patient with me for. Other than the merge
issues, functionality is working properly in linux-next :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXSgpnQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykcwgCfS30OR4JmwZydWGJ7zK/cHqk+KjsAnjOxjC1K
LpRyb3zX29oChFaZkc5a
=XrEZ
-----END PGP SIGNATURE-----
Merge tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core and debugfs updates from Greg KH:
"Here is the "big" driver core and debugfs changes for 5.3-rc1
It's a lot of different patches, all across the tree due to some api
changes and lots of debugfs cleanups.
Other than the debugfs cleanups, in this set of changes we have:
- bus iteration function cleanups
- scripts/get_abi.pl tool to display and parse Documentation/ABI
entries in a simple way
- cleanups to Documenatation/ABI/ entries to make them parse easier
due to typos and other minor things
- default_attrs use for some ktype users
- driver model documentation file conversions to .rst
- compressed firmware file loading
- deferred probe fixes
All of these have been in linux-next for a while, with a bunch of
merge issues that Stephen has been patient with me for"
* tag 'driver-core-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (102 commits)
debugfs: make error message a bit more verbose
orangefs: fix build warning from debugfs cleanup patch
ubifs: fix build warning after debugfs cleanup patch
driver: core: Allow subsystems to continue deferring probe
drivers: base: cacheinfo: Ensure cpu hotplug work is done before Intel RDT
arch_topology: Remove error messages on out-of-memory conditions
lib: notifier-error-inject: no need to check return value of debugfs_create functions
swiotlb: no need to check return value of debugfs_create functions
ceph: no need to check return value of debugfs_create functions
sunrpc: no need to check return value of debugfs_create functions
ubifs: no need to check return value of debugfs_create functions
orangefs: no need to check return value of debugfs_create functions
nfsd: no need to check return value of debugfs_create functions
lib: 842: no need to check return value of debugfs_create functions
debugfs: provide pr_fmt() macro
debugfs: log errors when something goes wrong
drivers: s390/cio: Fix compilation warning about const qualifiers
drivers: Add generic helper to match by of_node
driver_find_device: Unify the match function with class_find_device()
bus_find_device: Unify the match callback with class_find_device
...
Previously, if mbox_request_channel_byname was used with a name
which did not exist in the "mbox-names" property of a mailbox
client, the mailbox corresponding to the last entry in the
"mbox-names" list would be incorrectly selected.
With this patch, -EINVAL is returned if the named mailbox is
not found.
Signed-off-by: Morten Borup Petersen <morten_bp@live.dk>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
If Tegra HSP device tree does not have 'shared irqs',
mailboxes pointer is NULL. Add non-NULL HSP mailboxes
check in resume callback before tegra_hsp_mailbox_startup()
call and prevent NULL pointer exception.
Signed-off-by: Bitan Biswas <bbiswas@nvidia.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Several drivers cast a struct device pointer to a struct
platform_device pointer only to then call platform_get_drvdata().
To improve readability, these constructs can be simplified
by using dev_get_drvdata() directly.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
GIEn is enabled at startup for RX doorbell mailboxes so
we need to clear the bit at shutdown in order to avoid
leaving the interrupt line enabled.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
The TI K3 AM65x and J721E family of SoCs have a new Mailbox IP that
is based on the existing Mailbox IP present in OMAP architecture based
SoCs. Each instance of the legacy OMAP Mailbox IP is now a single cluster
within the newer Mailbox IP instance on K3 architecture based SoCs. A
single K3 Mailbox IP instance has multiple clusters with each cluster
providing the same functionality as the existing OMAP Mailbox IP.
Reuse the existing OMAP Mailbox driver to extend the support for this
newer IP present within the Main NavSS block on K3 SoCs. The K3 family
of SoCs use 64-bit ARMv8 processors for running Linux, so the driver is
also enhanced to deal with the differences between the 32-bit message
payloads and the 64-bit pointers used by the client drivers.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch just re-orders some of the headers includes and also drop
the ones that are unnecessary.
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Add spinlock protection on IPCC register update to avoid race condition.
Without this fix, stm32_ipcc_set_bits and stm32_ipcc_clr_bits can be
called in parallel for different channels. This results in register
corruptions.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Reviewed-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation the gpl this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
version 2 gplv2 for more details you should have received a copy of
the gnu general public license version 2 gplv2 along with this
source code
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 16 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081201.771169395@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation version 2 of the license this program
is distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 100 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.918357685@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 and
only version 2 as published by the free software foundation this
program is distributed in the hope that it will be useful but
without any warranty without even the implied warranty of
merchantability or fitness for a particular purpose see the gnu
general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 294 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141900.825281744@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details you should have received a copy of the gnu general
public license along with this program if not see http www gnu org
licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 228 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528171438.107155473@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 3 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not see http www gnu org licenses
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details [based]
[from] [clk] [highbank] [c] you should have received a copy of the
gnu general public license along with this program if not see http
www gnu org licenses
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 355 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Jilayne Lovejoy <opensource@jilayne.com>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190519154041.837383322@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include when we had clk_readl() and clk_writel(), but those are gone now
so this patch pushes the dependency out to the users of clk-provider.h.
-----BEGIN PGP SIGNATURE-----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=JjQo
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull more clk framework updates from Stephen Boyd:
"One more patch to remove io.h from clk-provider.h.
We used to need this include when we had clk_readl() and clk_writel(),
but those are gone now so this patch pushes the dependency out to the
users of clk-provider.h"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Remove io.h from clk-provider.h
- Misc: Use devm_ api for imx and platform_get_irq for stm32
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEE6EwehDt/SOnwFyTyf9lkf8eYP5UFAlzTv38ACgkQf9lkf8eY
P5VOQQ//d2rKhGB1GjVZQlezRa+AOLWr69cbN4mcxUvXp+PJmrcnqn1Ld7QzPXCl
/Xc/2+KxtZ5WX7vtmGu45eSFiCqf2apXfDaQf89ZrtCbUKT1GBJRUvvBeCmFv4pZ
bnA0PTCsHkpdvttmM2W++ZHFmgVxKOTQmtTZFsmwohJNfALkoQaw9NgKUuBKzPdI
DutmXNBLXm+EkEjuIjvsKdgE63g49BTio9BRzX85+PKYmRohOa5xb05pW4KLOvOW
WJ4KeUDHdWinIoedBg+FGlgWjACP3at6h3sKVqDsv76NmsCZHWjh3OV2pqQSp1ta
n7HD/xPoGKNRDb+8r1CL3YLgwY4Hdvkq73koX8BGJ1jkB7LmikofGz0tnigcjrY/
D4QIPu+nIsi7hZs4S2nSMvvLWcdhUkDFa1F0hf3shYV+tPqUAFMYeG5MwMEQ4zqW
KMUieCPRA4n5jiwQ3CBZgfcB+tCNJnsEkDtLoJydKNvgawpTanff7IJO2vALN64K
PnIcPkHzFlbQj8lOLffCTFqqnOabkwaxeyV5r9oiT0OAg0paRBXrAo3VyVONzwqK
vMAhNSygqeKudQ8EQcQS+0ymyjfSCJXa1M93lVG679VKcyVVrs0uEhjvub1abv3v
Co08qKk18lsqYc55E8BzZ4T+F/mifzmEIPblM6EA9DnooSSrE/o=
=rUxA
-----END PGP SIGNATURE-----
Merge tag 'mailbox-v5.2' of git://git.linaro.org/landing-teams/working/fujitsu/integration
Pull mailbox updates from Jassi Brar:
- New driver: Armada 37xx mailbox controller
- Misc: Use devm_ api for imx and platform_get_irq for stm32
* tag 'mailbox-v5.2' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Add support for Armada 37xx rWTM mailbox
dt-bindings: mailbox: Document armada-3700-rwtm-mailbox binding
mailbox: stm32-ipcc: check invalid irq
mailbox: imx: use devm_platform_ioremap_resource() to simplify code
This adds support for the mailbox via which the kernel can communicate
with the firmware running on the secure processor of the Armada 37xx
SOC.
The rWTM secure processor has access to internal eFuses and
cryptographic circuits, such as the Entropy Bit Generator to generate
true random numbers.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
On failure of_irq_get() returns a negative value or zero, which is
not handled as an error in the existing implementation.
Instead of using this API, use platform_get_irq() that returns
exclusively a negative value on failure.
Also, do not output an error log in case of defer probe error.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Use the new helper devm_platform_ioremap_resource() which wraps the
platform_get_resource() and devm_ioremap_resource() together, to
simplify the code.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Parsing entries in an ACPI table had assumed a generic header
structure. There is no standard ACPI header, though, so less common
layouts with different field sizes required custom parsers to go through
their subtable entry list.
Create the infrastructure for adding different table types so parsing
the entries array may be more reused for all ACPI system tables and
the common code doesn't need to be duplicated.
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Tested-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Brice Goglin <Brice.Goglin@inria.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
During noirq suspend phase, mailbox MU irq will be masked
but many drivers still need to communicate with system
controller firmware via mailbox, if MU irq is masked, it
will cause RPC timeout as below:
[ 23.372103] imx-scu scu: RPC send msg timeout
Setting MU irq to be wakeup source is NOT working as GIC
driver does NOT have .irq_set_wake implemented, so to
support suspend/resume, just make imx mailbox driver NOT
suspend, since MU is always a wakeup source on i.MX platforms
with system controller inside, and its power/clock is
maintained by system controller, mailbox driver no need
to manage them.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
This patch is to introduce ZynqMP IPI mailbox controller driver
to use the ZynqMP IPI block as mailboxes.
Signed-off-by: Wendy Liang <wendy.liang@xilinx.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
