This patch fixes rounding bug in emulation for double float operating on PowerPC platform.
When pack double float operand, it need to truncate the tail due to the limited precision.
If the truncated part is not zero, the last bit of work bit (totally 3 bits) need to '|' 1.
This patch is completed in _FP_FRAC_SRS_2(X,N,sz) (arch/powerpc/math-emu/op-2.h).
Originally the code leftwards rotates the operand to just keep the truncated part,
then check whether it is zero. However, the number it rotates is not correct when
N is not smaller than _FP_W_TYPE_SIZE, and it will cause the work bit '|' 1 in the improper case.
This patch fixes this issue.
Signed-off-by: Liu Yu <b13201@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This was recently made configurable, and needs to be set for these boards.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Remove exports of __res and cpm_install_handler/cpm_free_handler. Remove
cpm_install_handler/cpm_free_handler from the commproc.h as well. Both
were used for ARCH=ppc and aren't defined for ARCH=powerpc.
CC arch/powerpc/kernel/ppc_ksyms.o
arch/powerpc/kernel/ppc_ksyms.c:180: error: '__res' undeclared here (not in a function)
arch/powerpc/kernel/ppc_ksyms.c:180: warning: type defaults to 'int' in declaration of '__res'
make[1]: *** [arch/powerpc/kernel/ppc_ksyms.o] Error 1
make: *** [arch/powerpc/kernel] Error 2
LD .tmp_vmlinux1
arch/powerpc/kernel/built-in.o:(__ksymtab+0x198): undefined reference to `cpm_free_handler'
arch/powerpc/kernel/built-in.o:(__ksymtab+0x1a0): undefined reference to `cpm_install_handler'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
fpi->cp_command should be overwritten only if CONFIG_PPC_CPM_NEW_BINDING
is NOT set. Otherwise it is already set from the device tree.
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need to mask out the proper bits when testing the dispatch status
register else we can see unrelated NACK bits from previous cross call
sends.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch against 2.6.23 sparc-2.6.git contains a number of minor
cleanups of the sparc serial drivers. Initially I fixed this build
warning:
WARNING: vmlinux.o(.text+0x107a2c): Section mismatch: reference to .init.text:add_preferred_console (between 'sunserial_console_match' and 'sunserial_console_termios')
which is done by declaring sunserial_console_match() as __init. This
resulted in build warnings on sunserial_current_minor. To resolve
these the variable was changed so it is no longer global, and to hide
operations on it inside 2 new functions. These functions handle the
UART minor handling code that is common to all sparc serial drivers.
These changes allowed to clean up the uart counters in all the sparc
serial drivers, and the administration of minor device numbers.
Lastly, sunserial_console_termios() does not need to be exported since
it is only called from non-modular code.
Sadly, the following build warning still exists:
WARNING: vmlinux.o(__ksymtab+0x2910): Section mismatch: reference to .init.text:sunserial_console_match (between '__ksymtab_sunserial_console_match' and '__ksymtab_sunserial_unregister_minors')
This could be resolved by not exporting sunserial_console_match(), but
this is not possible at the moment because it is being called from
modular code. On the other hand, this is a bogus warning since it
comes from a ksymtab section.
Signed-off-by: Martin Habets <errandir_news@mph.eclipse.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Build fix to the isp1301_omap driver ... this driver gets built
more often in the OMAP tree than in mainline, partly because the
defconfig for H2 (plus probably H3 and H4) needs updating.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This is required to let hwmon drivers attach to the adapter.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
videobuf_dvb needs videobuf_read_start. The EXPORT_SYMBOL_GPL() were removed by
a previous patch. However, videobuf_dvb needs this.
This patch re-adds videobuf_read_start, doing the proper lock.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This reverts commit 70eba18b56, as per
Jeff Garzik:
"That was meant for 2.6.25, and actually (due to patching) applied to
a completely unrelated 2.6.24 net driver."
Noted-by: Roland Dreier <rdreier@cisco.com>
Requested-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On Tue, 4 Dec 2007, Ingo Molnar wrote:
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_get_tuner_i2c_master'
> drivers/built-in.o: In function `dibusb_dib3000mc_tuner_attach':
> : undefined reference to `dib3000mc_set_config'
Seems like -common part contains also code that is not completely
common to all the modules.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cxusb needs tuner-xc2028*.h files, but Makefile is not adding its patch
drivers/media/dvb/dvb-usb/cxusb.c:33:26: error: tuner-xc2028.h: File not found
drivers/media/dvb/dvb-usb/cxusb.c:34:32: error: tuner-xc2028-types.h: File not found
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are several months my hvr1110 stop working.
This is very simple to fix, for my card revision at least, by setting a
missing field to the hauppauge_hvr_1110_config.
Signed-off-by: Benoit Istin <beistin@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is pretty serious bug. map->count is never initialized after the
call to kmalloc making the count start at some random trash value. The
end result is leaking videobufs.
Also, fix up the debug statements to print unsigned values.
Pushed to http://ifup.org/hg/v4l-dvb too
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The saa7134 video driver starts dropping frames when used together with the
saa7134-alsa driver. Frames are dropped because when an audio event is waiting
the driver simply ignores the interrupt and passes it on to the saa7134-alsa
interrupt handler. The alsa interrupt handler in turn acknowledges all types
of events thus clearing the pending video events as well. Fix by only masking
out the audio event in the video interrupt handler and by only acknowledging
the audio event in the alsa driver.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux for composite over s-video input was wrong.
Signed-off-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Complement va_start() with va_end() + minor style fixes in the same function.
Signed-off-by: Richard Knutsson <ricknu-0@student.ltu.se>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The period handling in saa7134-alsa is broken in two ways. First, the
minimum number of periods of two does not work, because the dma is setup
two periods ahead in the irq handler. Fix the minimum to four periods.
Second, the code assumes that the number of periods is divisible by two,
which isn't always the case on ALSA. Fix by adding a constraint.
Signed-off-by: Heikki Lindholm <holindho@cs.helsinki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The default adc_clock for the zl10353 is different from what was originally
thought to be the case and the TRL nominal rate formula was incorrect as a
result. Use a better (and hopefully now correct) formula.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Drivers were using cookie cutter code for stopping the read/stream. Use the
new videobuf_stop function which is lock safe.
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Add comments to functions that require that caller hold q->lock
- Add __videobuf_mmap_free that doesn't hold q->lock for use within videobuf
- Add locking to videobuf_mmap_free
- Fix linux/drivers/media/common/saa7146_video.c which was holding lock around
videobuf_read_stop
- Add locking to functions that operate on a queue
- Add videobuf_stop to take care of stopping in both the read and stream case
TODO: bttv still has an unsafe call to videobuf_queue_is_busy
Signed-off-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a modified version of a patch previously posted by Thomas
Unverzagt.
Signed-off-by: Hartmut Hackmann <hartmut.hackmann@t-online.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch is required so that the autodetecion code also works after
a reboot.
Setting the I2C speed does not seem to be supported for em2800.
Signed-off-by: Sascha Sommer <saschasommer@freenet.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If we get an error during the actual policy lookup we don't free the
original dst while the caller expects us to always free the original
dst in case of error.
This patch fixes that.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vlan module cleanup function starts with
vlan_netlink_fini();
vlan_ioctl_set(NULL);
The first call removes all the vlan devices and
the second one closes the vlan ioctl.
AFAIS there's a tiny race window between these two
calls - after rtnl unregistered all the vlans, but
the ioctl handler isn't set to NULL yet, user can
manage to call this ioctl and create one vlan device,
and that this function will later BUG_ON seeing
non-emply hashes.
I think, that we must first close the vlan ioctl
and only after this remove all the vlans with the
vlan_netlink_fini() call.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some return value comments for void functions.
Fixed it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets can be left in the RX ring if the NAPI budget is reached.
This is caused by storing the latest rx index at the beginning of
bnx2_rx_int(). We may not process all the work up to this index
if the budget is reached and so some packets in the RX ring may rot
when we later check for more work using this stored rx index.
The fix is to not store this latest hw index and only store the
processed rx index. We use a new function bnx2_get_hw_rx_cons()
to fetch the latest hw rx index.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. netif_rx_ni calls netif_rx, so the same problem occurs in
the files below.
I have left the updating of dev->last_rx after the calls to netif_rx_ni
because it seems time dependent, but moved the other field updates before.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recently, Wang Chen submitted a patch
(d30f53aeb3) to move a call to netif_rx(skb)
after a subsequent reference to skb, because netif_rx may call kfree_skb on
its argument. The same problem occurs in some other drivers as well.
This was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression skb, e,e1;
@@
(
netif_rx(skb);
|
netif_rx_ni(skb);
)
... when != skb = e
(
skb = e1
|
* skb
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC4303 introduces dummy packets with a nexthdr value of 59
to implement traffic confidentiality. Such packets need to
be dropped silently and the payload may not be attempted to
be parsed as it consists of random chunk.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to Herbert, the ipv4_devconf_setall should be called
only when the ifa is added to the device. However, failed
ifa allocation may bring things into inconsistent state.
Move the call to ipv4_devconf_setall after the ifa allocation.
Fits both net-2.6 (with offsets) and net-2.6.25 (cleanly).
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTCF_xxx flags, defined in include/linux/in_route.h) are available for
IPv4 route (rtable) entries only. Use RTF_xxx flags instead, defined
in include/linux/ipv6_route.h, for IPv6 route entries (rt6_info).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some versions of Xen 3.x set their magic number to "xen-3.[12]", so
relax the test to match them.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
