The TempoTec HiFier has a somwhat different architecture; remove it from
the list of cards that are known to be supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The available sample rates on CS5535 depend on AC97 codec chip.
Set the additional hw params limit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add one more indirection to the lookup of the snd_pcm_hardware
structures so that we can save the space of the duplicate ones.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Change the oxygen_spdif_input_bits_changed() function so that clock
changes on the SPDIF input are correctly detected. This means that
sample rates greater than 96 kHz are now supported.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix some wrong values for the definitions of the source masks for DACS 1
and 3.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Actually use the template that was maybe changed by the control filter
instead of the original one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Instead of having model-specific fields in the common struct oxygen, put
them into a private structure that is allocated together with the card
structure.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
According to the datasheets, the SPI clock cycle must be at least 200 ns
for the AK4396 and the WM8785, so we cannot use the default 160 ns.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow to record with 32 kHz, 64 kHz, 88.2 kHz and 176.4 kHz with cards
that have a WM8785 ADC.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add symbol definitions for the various codecs and GPIO pins.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The MIDI bit in the MISC register is set by default and cannot be used
to detect the presence of a MIDI port. Instead, add a parameter to the
oxygen_pci_probe() function so that model drivers can specify this.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Use the DMA_PAUSE register for pausing instead of stopping DMA.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add documentation entries for snd-oxygen and snd-virtuoso.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Reported by Al Viro:
In copy_tlv(), the size of kmalloc is wrongly calculated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
In azx_[rirb_]get_response(), the timeout is checked at the end of the loop.
It's better to be checked just after the check of the RIRB index to avoid
a bogus error with a too long msleep().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Clean up ice1712/ice1724 codes. The board-specific data is allocated
locally in each code instead of having an ungly union in struct ice1712.
Also, fix coding issues in prodigy_hifi.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch adds additional output to the /proc codec#X info.
The following pieces of information are added to the output:
- Balanced, L/R swap, trigger, impedance sense pin capabilities
- Vref pin capabilities
- Current Vref pin widget control setting
- Default configuration association, sequence, and misc bit test
- EAPD/BTL bits conveying balanced mode, EAPD, and L/R swap
- Power state modified to show state name as well as setting vs actual value
- GPIO parameter output on Audio Function Group, including enumeration of IO
pins which are indicated present (Any I and O pins are not output at this
time)
- Stripe and L/R swap widget capabilities
- All digital converter bits: enable, validity, validity config, preemphasis,
copyright, non-audio, professional, generation level, and content category
- Converter stream and channel values for in/out widgets
- SDI select value for in widgets
- Unsolicited response widget capability tag and enabled bit
- Delay widget capability value
- Processing widget capability benign bit and number of coefficients
- Realtek Define Registers: processing coefficient, coefficient index
[Also, fixed space/tab issues and make codes a bit more readable
-- Takashi]
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The default playback routing must be 0xe4, not 0xe1; the front and
surround DACs were exchanged.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add more symbols for registers and register fields.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Enable mmap support in the MPC8610 ASoC driver. The driver can use ALSA's
default mmap functionality, it was just not enabled previously.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
For codec conexant 5045, I found that the name of 'Capture Source Items'
is different from the name of mixer.
The mixer is:
HDA_CODEC_VOLUME('Ext Mic Playback Volume', 0x17, 0x2, HDA_INPUT),
HDA_CODEC_MUTE('Ext Mic Playback Switch', 0x17, 0x2, HDA_INPUT),
But the capture source item is :
static struct hda_input_mux cxt5045_capture_source = {
.num_items = 2,
.items = {
{ 'IntMic', 0x1 },
{ 'LineIn', 0x2 },
}
};
I think that it's better to change the name of capture_source to avoid
misunderstanding.
Signed-off-by: Jiang zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The benq r55e laptop have 3 jacks on the front panel.
One for HP, one for Line In and one for Mic In.
This patch implemented a new model to support it.
Signed-off-by: Jiang Zhe <zhe.jiang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the description of the model fujitsu for Cx5045 codec chip.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add proper register bit symbols for the I2S format field, and allow card
models to configure the I2S format to be used for the DACs and ADCs.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
See ALSA bug#2384 for more details.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Konstantin Kletschke <konsti@ku-gbr.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Codec with id 11c1:1040 sitting on hda bus isn't si3054-compatible.
It should be removed from patch_si3054.c id list.
The detailed information
http://archives.linmodems.org/26457
From: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Some machines with STAC codecs seem to have problems (e.g. no audible
playback) when the delay in codec-read routine is too short.
I still don't figure out which command sequence causes this problem
(due to lack of test hardware), but it's known that increasing the
delay fixes. So, added a stupid workaround here temporarily...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This device has io_type == 1 (Multiface) and firmware_rev > 0xa
(fixes regression from changeset 5326)
Signed-off-by: Andreas Degert <ad@papyrus-gmbh.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch provides the snd-powermac sound driver with the ability to handle
dead DMA transfers. If a dead DMA transfer is detected, the driver now sets
up a new DMA transfer to continue with the sound output at the point where the
old transfer died.
This dead DMA transfer handling has become necessary with recent kernels on
certain G4 PowerMacs. Please refer to the following URLs for more information:
https://bugtrack.alsa-project.org/alsa-bug/view.php?id=3126https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.20/+bug/87652http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=436723
The patch is based on the dead DMA transfer handling code from the old dmasound
driver which can be found in the file sound/oss/dmasound/dmasound_awacs.c in
the Linux source code.
Signed-off-by: T. H. Huth <th.huth@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in caiaq: these __devinit functions can be
called at any time so they should not be __devinit.
WARNING: vmlinux.o(.text+0x10a8dae): Section mismatch: reference to .init.text:snd_usb_caiaq_audio_init (between 'setup_card' and 'create_card')
WARNING: vmlinux.o(.text+0x10a8dd6): Section mismatch: reference to .init.text:snd_usb_caiaq_midi_init (between 'setup_card' and 'create_card')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in hdsp: snd_hdsp_proc_init() can be called from
an ioctl at any time.
WARNING: vmlinux.o(.text+0x1089bc2): Section mismatch: reference to .init.text: (between 'snd_hdsp_create_alsa_devices' and 'snd_hdsp_free')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in atiixp by making some functions __devinit.
WARNING: vmlinux.o(.text+0xfd9304): Section mismatch: reference to .init.data:atiixp_quirks (between 'ac97_probing_bugs' and 'snd_atiixp_codec_detect')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in ad1889 by renaming the pci_driver variable to a
whitelisted variable name.
WARNING: vmlinux.o(.data+0x2e5ff0): Section mismatch: reference to .init.text:snd_ad1889_probe (between 'ad1889_pci' and 'index')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatches in mts64 by making a static variable __devinitdata.
WARNING: vmlinux.o(.data+0x2e33f0): Section mismatch: reference to .init.data:mts64_ctl_smpte_switch (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e33f8): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_hours (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3400): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_minutes (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3408): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_seconds (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3410): Section mismatch: reference to .init.data:mts64_ctl_smpte_time_frames (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
WARNING: vmlinux.o(.data+0x2e3418): Section mismatch: reference to .init.data:mts64_ctl_smpte_fps (between 'control.19929' and 'snd_mts64_rawmidi_output_ops')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a callback to the model structure to allow modification of the
hardware PCM limits.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow the models to modify mixer controls before they are added to the
card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Allow the card models to specify whether each of the hardware DMA
channels is used.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Add a field to the model structure so that it is possible to have a card
where the SPI outputs 4 and 5 are used for an EEPROM.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Only initialize and create mixer controls for the first AC97 codec when
one has actually been detected.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Enable the SPDIF input-pin on VIA codecs when SPDIF-input is enabled
by BIOS. Also, including a bit code clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Added the support of Dell OEM laptops (Vostro 1200) with ALC268 codec.
The new model=dell is provided.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
It turned out that the PCBEEP element (0x1d) is disabled on some hardwares
although it's defined in the datasheet. Because of the error at info of
this element, the mixer gets totally unusable.
Since the PCBEEP isn't that important feature, it's safer to disable this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
There are two similar GPIO-enablement codes in patch_sigmatel.c.
Let's clean up.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This patch removes hardcoded values for the number of streams supported
by the southbridge in most chipsets, and reads these values from the
chipset directly. Most systems are hardwired for 4 streams in each
direction, but newer chipsets change that capability.
Signed-off-by: Tobin Davis <tdavis@dsl-only.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Rename the 'PCM Playback Volume'/'Switch' mixer controls to 'Master'.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This busy_wait is not needed after latest changes
to the cs4231-lib
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The line input cannot be mixed with the other inputs, so we have to mute
the other input switches when it is selected.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
