Extended hardware support and support dump images:
- Make the size to be MAILBOX_SYSFS_MAX (4096) so that it allows the maximum
sysfs binary access interface possible.
- Add ids and model names for new hardware
- Add capability of inducing SLI4 firmware dump obj file
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Miscellaneous Fixes and Corrections
- Remove the memset in the lpfc_sli4_remove_rpi_hdrs call.
- Correct swapping of SGE word 2 relative to offset value
- Reorganize CQ and EQ usage to comply with SLI4 Specification.
- Expand the driver to check the rn bit. Only detect an error if the error bit
is set and the RN bit is NOT set.
- If mailbox completion code is not success AND the mailbox status is success,
then and only then will the driver overwrite the mailbox status.
- When driver initializing device, if the device is on a PCIe bus, set
PCI's "needs fundamental reset" bit so that EEH uses fundamental reset
instead of hot reset for recovery.
- Prevent driver from using new WWN when changed in firmware (until driver
reload)
- When HBA reports maximum SGE size > 0xffffffff (infinite), override
with 0x80000000.
- Fixed potential missed SLI4 device initialization failure conditions.
- Added 100ms delay before driver action following IF_TYPE_2 function reset.
- Reverted patch to UNREG/REG on PLOGI to mapped/unmapped node.
- Add a check for the CVL received flag in the fcf inuse routine to avoid
unregistering the fcf if Devloss fires before Delay discover timer fires.
Signed-off-by: Alex Iannicelli <alex.iannicelli@emulex.com>
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This allows a libsas driver to optionally provide a soft reset handler
for libata to drive. The isci driver allows software to control the
assertion/deassertion of SRST.
[jejb: checkpatch.pl fixes]
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Head off doomed-to-fail i/o in sas_queuecommand before sending it down
the ata path.
Before:
sd 7:0:0:0: [sdd] Synchronizing SCSI cache
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
ata8: no sense translation for status: 0x00
ata8: translated ATA stat/err 0x00/00 to SCSI SK/ASC/ASCQ 0xb/00/00
ata8.00: device reported invalid CHS sector 0
ata8: status=0x00 { }
sd 7:0:0:0: [sdd] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE
sd 7:0:0:0: [sdd] Sense Key : Aborted Command [current] [descriptor]
sd 7:0:0:0: [sdd] Add. Sense: No additional sense information
sd 7:0:0:0: [sdd] Stopping disk
After:
sd 9:0:0:0: [sdd] Synchronizing SCSI cache
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
sd 9:0:0:0: [sdd] Stopping disk
sd 9:0:0:0: [sdd] START_STOP FAILED
sd 9:0:0:0: [sdd] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
This is a cosmetic change as sata i/o can still leak to a gone device,
but this addresses the nominal hotplug case when releasing the target.
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Commit 56dd2c06 "libsas: Don't issue commands to devices that have been
hot-removed" edited Darrick's original patch to remove setting 'gone' in
the sas_deform_port() path because that prevented scsi sync cache
commands from being issued when the driver was unloaded. However, this
allows true device gone notifications (as signaled port phy events) to
trigger sync cache commands to devices that are known to be unreachable.
Teach libsas which sas_deform_port() invocations are likely device gone
events.
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Commit 1292500b replaced
"=m" (*field) : "1" (*field)
with
"=m" (*field) :
with comment "The following patch fixes it by using the '+' operator on
the (*field) operand, marking it as read-write to gcc."
'+' was actually forgotten. This really puts it.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
drivers/scsi/osst.c: In function '__os_scsi_tape_open':
drivers/scsi/osst.c:4705: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Index i was already used in the outer loop. Fixes a potentially-infinite
loop.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Willem Riede <osst@riede.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch converts target core and follwing scsi-misc upstream fabric
modules to use include/scsi/scsi_tcq.h includes for SIMPLE, HEAD_OF_QUEUE
and ORDERED SCSI tasks instead of scsi/libsas.h with TASK_ATTR*
*) tcm_loop: Convert tcm_loop_allocate_core_cmd() + tcm_loop_device_reset() to
scsi_tcq.h
*) tcm_fc: Convert ft_send_cmd() from FCP_PTA_* to scsi_tcq.h
Reported-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch converts transport_core_report_lun_response() to use
drivers/scsi/scsi_scan.c:int_to_scsilun instead of using the
struct target_core_fabric_ops->pack_lun() fabric provided API vector.
It also removes the tfo->pack_lun check from target_fabric_tf_ops_check()
and removes from struct target_core_fabric_ops->pack_lun() from
target_core_fabric_ops.h, and the following mainline scsi-misc fabric
modules:
*) tcm_loop: Drop tcm_loop_pack_lun() usage
*) tcm_fc: Drop ft_pack_lun() usage
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch fixes a bug where task->task_execute_queue=1 was not being
cleared once se_task had been removed from se_device->execute_task_list,
resulting in an OOPs in core_tmr_lun_reset() for the task->task_active=0
case where transport_remove_task_from_execute_queue() was incorrectly
being called.
This patch fixes two cases in transport_get_task_from_execute_queue()
and transport_remove_task_from_execute_queue() to properly clear
task->task_execute_queue=0 once list_del(&task->t_execute_list) has
been called.
It also adds an explict check in transport_remove_task_from_execute_queue()
to dump_stack + return if called with task->task_execute_queue=0.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch addresses a bug in the target core release path for HW
operation where transport_free_dev_tasks() was incorrectly being called
from transport_lun_remove_cmd() while releasing a se_cmd reference and
calling struct target_core_fabric_ops->queue_data_in().
This would result in a OOPs with HW target mode when the release of
se_task->task_sg[] would happen before pci_unmap_sg() can be called in
HW target mode fabric module code. This patch addresses the issue by
moving transport_free_dev_tasks() from transport_lun_remove_cmd() into
transport_generic_free_cmd(), and adding TRANSPORT_FREE_CMD_INTR and
transport_generic_free_cmd_intr() to allow se_cmd descriptor release
to happen fromfrom within transport_processing_thread() process context
when release of se_cmd is not possible from HW interrupt context.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch fixes two bugs wrt to the interrupt context usage of target
core with HW target mode drivers. It first converts the usage of struct
se_device->stats_lock in transport_get_lun_for_cmd() and core_tmr_lun_reset()
to properly use spin_lock_irq() to address an BUG with CONFIG_LOCKDEP_SUPPORT=y
enabled.
This patch also adds a 'in_interrupt()' check to allow GFP_ATOMIC usage from
core_tmr_alloc_req() to fix a 'sleeping in interrupt context' BUG with HW
target fabrics that require this logic to function.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch fixes a bug in transport_do_task_sg_chain() used by HW target
mode modules with sg_chain() to provide a single sg_next() walkable memory
layout for use with pci_map_sg() and friends. This patch addresses an
issue with mapping multiple small block max_sector tasks across multiple
struct se_task->task_sg[] mappings for HW target mode operation.
This was causing OOPs with (cmd->t_task->t_tasks_no > 1) I/O traffic for
HW target drivers using transport_do_task_sg_chain(), and has been tested
so far with tcm_fc(openfcoe), tcm_qla2xxx, and ib_srpt fabrics with
t_tasks_no > 1 IBLOCK backends using a smaller max_sectors to trigger the
original issue.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Acked-by: Kiran Patil <kiran.patil@intel.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
In error recovery, most scsi error recovery stages will send a TUR command
for every bad command when a driver's error handler reports success. When
several bad commands to the same device, this results in a device
being probed multiple times.
This becomes very problematic if the device or connection is in a state
where the device still doesn't respond to commands even after a recovery
function returns success. The error handler must wait for the test
commands to time out. The time waiting for the redundant commands can
drastically lengthen error recovery.
This patch alters the scsi mid-layer's error routines to send test commands
once per device instead of once per bad command. This can drastically
lower error recovery time.
[jejb: fixed up whitespace and formatting]
Signed-of-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Some kernel transport drivers unconditionally disable
retrieval of the Caching mode page. One such for example is
the BBB/CBI transport over USB. Such a restraint is too
harsh as some devices do support the Caching mode
page. Unconditionally enabling the retrieval of this mode
page over those transports at their transport code level may
result in some devices failing and becoming unusable.
This patch implements a method of retrieving the Caching
mode page without unconditionally enabling it in the
transports which unconditionally disable it. The idea is to
ask for all supported pages, page code 0x3F, and then search
for the Caching mode page in the mode parameter data
returned. The sd driver already asks for all the mode pages
supported by the attached device by setting the page code to
0x3F in order to find out if the media is write protected by
reading the WP bit in the Device Specific Parameter
field. It then attempts to retrieve only the Caching mode
page by setting the page code to 8 and actually attempting
to retrieve it if and only if the transport allows it.
The method implemented here is that if the transport doesn't
allow retrieval of the Caching mode page and the device is
not RBC, then we ask for all pages supported by setting the
page code to 0x3F (similarly to how the WP bit is retrieved
above), and then we search for the Caching mode page in the
mode parameter data returned.
With this patch, devices over SATA, report this (no change):
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: Attached scsi generic sg0 type 0
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
Oct 22 18:45:58 localhost kernel: sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
Smart devices report their Caching mode page. This is a
change where we'd previously see the kernel making
assumption about the device's cache being write-through:
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: Attached scsi generic sg2 type 0
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] 610472646 4096-byte logical blocks: (2.50 TB/2.27 TiB)
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write Protect is off
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Mode Sense: 47 00 10 08
Oct 22 18:45:58 localhost kernel: sd 6:0:0:0: [sdb] Write cache: enabled, read cache: enabled, supports DPO and FUA
And "dumb" devices over BBB, are correctly shown not to
support reporting the Caching mode page:
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] 15663104 512-byte logical blocks: (8.01 GB/7.46 GiB)
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Write Protect is off
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Mode Sense: 23 00 00 00
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] No Caching mode page present
Oct 22 18:49:06 localhost kernel: sd 7:0:0:0: [sdc] Assuming drive cache: write through
Version 2 adds this:
Some devices don't support page code 0x3F, and others require a
fixed transfer length of 192 bytes. This single commit includes a
patch by Alan Stern which fixes this.
Reported-and-tested-by: Richard Senior <richard@r-senior.demon.co.uk>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Luben Tuikov <ltuikov@yahoo.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Modified the event coalescing code for iSCSI offload to combat both
corner cases and optimize performance as follows:
1. Added mechanism to loop back a second time to process any leftover
CQEs that was generated by the hardware during the time the driver is
busy processing previous CQEs in the bh. This not only helps the
performance but also fixes the corner case when no more CQEs are being
generated in the pipeline; so those leftover CQEs will get a a chance
to be processed.
2. Added ARM_CQE_FP to distinguish between fast path arming versus
slow path arming. This change will guarantee that the CQEs will
always get a chance to be re-armed during fast path completions.
3. Removed the inline event coalescing division for perf optimization.
Also fixed a division-by-zero error when the event_coal_div module
param was set to 0.
4. Changed the default SQ WQEs size from 256 to 128 to match chip
default.
5. Changed the cmd_per_lun from 32 to 24.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Modified the 10s wait time for inflight offload connections to
advance to the next state to 2s based on test result.
Modified the 20s shutdown timeout to 30s based on test result.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The number of chip's internal command cell, which is use to generate
SCSI cmd packets to the target, was not initialized correctly by
the driver when the sq_size is changed from the default 128.
This, in turn, will create a problem where the chip's transmit pipe
will erroneously reuse an old command cell that is no longer valid.
The fix is to correctly initialize the chip's command cell upon setup.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Since queue_work does not requeue, there is no need to check
if a work is in progress using the AF_DPC_SCHEDULED flag.
queue_work would return if work is pending without adding the
work, do_dpc would again get invoked from qla4xxx_timer if
there is still DPC flags set.
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Corrected logic to don't check for F/W is alive if reset is already
in progress for ISP82XX
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Do not process interrupt unconditionally during mailbox processing which can
lead to spurious interrupt. Mailbox completion are now polled if interrupt are
disabled or wait for interrupt to come in if its enabled
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Complete the cmd if sense length is zero. For cases where sense
data spans across multiple iocb's by FW, we need to hold on to the
I/O (ha->status_srb != NULL) till we have processed them all and
copied the sense data from internal buffer to scsi_cmd sense buffer.
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
- Added MBOX_ASTS_DUPLICATE_IP AEN handling.
- Update MBOX_AEN_REG_COUNT to 8 so that driver will save status
of all mbox registers in aen_q
Signed-off-by: Prasanna Mumbai <prasanna.mumbai@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
As of SBC3r26 WRITE SAME(10) supports the UNMAP bit.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Ensure that the initial reference tag is passed on to the HBA firmware
for DIF Type 2 devices.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Kashyap Desai <Kashyap.Desai@lsi.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The block layer discard alignment is reported in bytes, not in units of
the logical block size.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Root cause: When kernel crashes, bfa IOC state machine and FW doesn't get
a notification and hence are not cleanly shutdown. So registers holding
driver/IOC state information are not reset back to valid disabled/parking
values. This causes subsequent driver initialization to hang during kdump
kernel boot.
Fix description: during the initialization of first PCI function, reset
corresponding register when unclean shutown is detect by reading chip
registers. This will make sure that ioc/fw gets clean re-initialization.
Signed-off-by: Jing Huang <huangj@brocade.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
If the driver is getting flooded with interrupts, there's a possibility
that the interrupt service routine could falsely detect a stuck interrupt
condition and reset the adapter.
This patch changes the logic such that the routine will loop back into
the command processing code one more time after detecting the stuck
interrupt signature. If there are no commands to process after that pass,
and the interrupt is still not cleared, then the driver will print the
"Error clearing HRRQ" message and reset the adapter.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
libfcoe's interface consists of create, destroy, enable,
disable and create_vn2vn. These are currently module
paramaters added durring the module initialization. A
concern arose that the module parameters were being added
with write permissions before the module had completed
initialization. The following code was added to each
sysfs store file.
* Make sure the module has been initialized, and is not about to be
* removed. Module parameter sysfs files are writable before the
* module_init function is called and after module_exit.
*/
if (THIS_MODULE->state != MODULE_STATE_LIVE)
goto out_nodev;
This check was called out as unhelpful as the module can
go dead at any time and therefore its state isn't a reliable
thing to look at as a sign of stability and initialization
completion. Also, that functional interfaces like these
should be added after module initialization.
This patch removes the unnecessary checks and hopes to
disprove the concern about initialization ordering.
Recent fcoe transport rework changes now require fcoe
transports to register with libfcoe before any operation
can take place. libfcoe may access some static variables
but nothing that could cause a problem. Once a fcoe transport
is registered, libfcoe is usable and any interface calls will
be functional.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Currently, when seq_send() fails in fc_fcp_send_data(),
fc_fcp_retry_cmd() would complete this failed I/O directly and let
scsi-ml retry. However, target side is not notified which may hang the
target. Instead, we should just bail out from from fc_fcp_send_data
and let scsi-ml times it out and aborts this I/O instead.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
In this case fsp was freed before error handler was invoked,
this is fixed by having SRR fsp reference freed by exch
destructor so that fsp will be always held until it exch
is freed.
Also don't reset fsp->recov_seq since this is needed by
SRR error handler to do exch done.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
In cases exch is already timed out then exch layer could
end up calling resp handler again for its response frame
received after timeout, though in this case fc_exch_timeout
handler would have already called resp with FC_EX_TIMEOUT.
This would cause REC response handler to release its
fsp pkt hold twice instead once and possibly similar issues
with other ELS exchanges in this race.
To avoid this race have resp updated under exch lock
in rx path, the resp would get set to NULL in case
of FC_EX_TIMEOUT under the same lock to prevent resp
callback after FC_EX_TIMEOUT.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
In case frame_send() fails, make sure to let the underlying HW release the DDP
context that has already been set up before calling frame_send().
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
When handling incoming request, if the operation code carried by the
received frame is not RSCN, the frame should be freed as in the RSCN
case, or there is memory leakage.
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
This patch adds a validation step before allowing creation of a new NPIV port.
It checks whether the WWPN passed for the new NPIV port to be created is unique
for the given physical port.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
Host doesnt handle CVL to NPIV instantiated ports correctly.
- As per FC-BB-5 Rev 2 CVLs with no VN_Port descriptors shall be treated as
implicit logout of ALL vn_ports.
- CVL for NPIV ports should be handled before physical port even if descriptor
for physical port appears before NPIV ports
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The following patch for megaraid_sas converts 6,10,12 byte CDB's to 16
byte CDB for large LBA's for FastPath IO.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
The following patch for megaraid_sas disables interrupts and
free_irq() in megasas_shutdown().
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <jbottomley@parallels.com>
