Support for special command is implemented in the AP Bus in the NQAP
function __ap_send. This is extended for a further parameter special.
When set, the special bit, in GR0 will be set. Therefor the ap_message
struct is extended for a further bit. Thus calling functions of
__ap_send can use the special parameter in ap_message to give to
__ap_send. Affected is in the first place ap_queue_message, which is
called by the actual card driver. The second part of this support is
that the card driver for the CEX3C needs to set this special bit, when
an according CPRB is sent to the driver.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Ralph Wuerthner <ralph.wuerthner@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
AP messages need to be initialized, before they will be used. Values
will be zeroized. This will be needed later when introducing support
for the special commands.
Signed-off-by: Felix Beck <felix.beck@de.ibm.com>
Signed-off-by: Ralph Wuerthner <ralph.wuerthner@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The first DASD that is set online for a specific logical control unit
has to do certain setup steps on the storage server to make full use
of it, for example it will enable PAV.
The features and characteristics reported by the storage server will
depend on this setup, so all other devices on the same LCU will need
to wait for the setup to be finished.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove strings from s390 debugfeature entries that could lead to a
crash when the data is read from dbf because the strings do not exist
any more.
Signed-off-by: Stefan Haberland <stefan.haberland@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Most of the error conditions reported by a FICON storage server
indicate situations which can be recovered. Sometimes the host just
needs to retry an I/O request, but sometimes the recovery
is more complex and requires the device driver to wait, choose
a different path, etc.
The DASD device driver has a fully featured error recovery
for normal block layer I/O, but not for internal I/O request which
are for example used during the device bring up.
This can lead to situations where the IPL of a system fails because
DASD devices are not properly recognized.
This patch will extend the internal I/O handling to use the existing
error recovery procedures.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The DASD device driver needs to explicitly enable the prefix command
on the storage server, before it can be used. Originally we enabled
this command along with others only if we wanted to support PAV.
However, today we require this command for other features like
High Performance FICON as well, so we need to always enable prefix.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
the todclk.h header file is dead code. Remove it.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When a DASD device is used with the DIAG discipline, the DIAG
initialization will indicate success or error with a respective
return code. So far we have interpreted a return code of 4 as error,
but it actually means that the initialization was successful, but
the device is read-only. To allow read-only devices to be used with
DIAG we need to accept a return code of 4 as success.
Re-initialization of the DIAG access is also part of the DIAG error
recovery. If we find that the access mode of a device has been
changed from writable to read-only while the device was in use,
we print an error message.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The pagetable walk usercopy functions have used a modified copy of the
do_exception() function for fault handling. This lead to inconsistencies
with recent changes to do_exception(), e.g. performance counters. This
patch changes the pagetable walk usercopy code to call do_exception()
directly, eliminating the redundancy. A new parameter is added to
do_exception() to specify the fault address.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Slim down the do_exception function to handle only the fast path of a
fault and move the exceptional cases into a new function. That slightly
increases the performance of the fault handling.
Build fix for !CONFIG_COMPAT by
Kamalesh Babulal <kamalesh@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
notify_page_fault does a preempt_disable/preempt_enable for each
fault generated by a kernel access to user space. If kprobes
is not active that is unnecessary since the interrupts are not
reenabled yet. To play safe repeat the kprobe_running check after
preempt_disable().
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce user_mode to replace the two variables switch_amode and
s390_noexec. There are three valid combinations of the old values:
1) switch_amode == 0 && s390_noexec == 0
2) switch_amode == 1 && s390_noexec == 0
3) switch_amode == 1 && s390_noexec == 1
They get replaced by
1) user_mode == HOME_SPACE_MODE
2) user_mode == PRIMARY_SPACE_MODE
3) user_mode == SECONDARY_SPACE_MODE
The new kernel parameter user_mode=[primary,secondary,home] lets
you choose the address space mode the user space processes should
use. In addition the CONFIG_S390_SWITCH_AMODE config option
is removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A data access in access-register mode always is a user mode access,
the code to inspect the access-registers can be removed. The second
change is to use a different test to check for no-execute fault.
The third change is to pass the translation exception identification
as parameter, in theory the trans_exc_code in the lowcore could have
been overwritten by the time the call to check_space from do_no_context
is done.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If we detect a busy subchannel after the driver's set_offline
callback returned in ccw_device_set_offline, the current behavior
is to unregister the device, which may lead to undesired
consequences. Change this to just quiesce the subchannel and go on
with the offline processing.
Note: This is no excuse for not fixing these drivers -
after the set_offline callback they should have no running IO!
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Improve error recovery for internal I/Os by repeating each I/O
256 times per path to cope with long-running non-permanent error
conditions. Also retry each path twice to cope with link flapping,
i.e. single paths becoming unavailable in the order in which they
are tried.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
IO subchannels are always unregistered in process context, so use
spin_lock_irq in the corresponding remove callback.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that there will be no more interrupts for an
unregistered device by using the same quiesce and disable loop
as in io_subchannel_shutdown.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Try to disable the old subchannel before we ask the driver core
to move the attached device to a new parent. This way we can use
the QUIESCE state during shutdown which prevents a possible use
after free situation in some error cases.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Handle a failing cio_disable_subchannel at the end of our device
recognition as if the recognition itself failed. This way
subsequent registration steps do not need to handle enabled
subchannels.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
DEV_STATE_QUIESCE is used to stop all IO on a busy subchannel.
This patch fixes the following problems related to the QUIESCE
state:
* Fix a potential race condition which could occur when the
resulting state was DEV_STATE_OFFLINE.
* Add missing locking around cio_disable_subchannel,
ccw_device_cancel_halt_clear and the cdev's handler.
* Loop until we know for sure that the subchannel is disabled.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The function ccw_device_unregister has to ensure to remove
all references obtained by device_add and device_initialize.
Unfortunately it gets called for devices which are
1) uninitialized, 2) initialized but unregistered, and
3) registered devices. To distinguish 1) and 2) this patch
introduces a new flag "initialized", which is 1 as long as we
hold the initial device reference.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
We used to maintain a "registered" flag in our ccw_device_private
structure. This patch removes the "registered" flag and converts
all users of it to device_is_registered which has the exact same
meaning.
Note: The usage the atomic operation test_and_clear_bit is replaced
by the non-atomic if (device_is_registered()) device_del(). This
will not do harm, since we serialize calls to ccw_device_unregister
with a single-threaded workqueue.
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
An Unconditional Reserve + Release operation (steal lock) for a
boxed device may fail when encountering special error cases
(e.g. unit checks or path errors). Fix this by using the more
robust ccw_request infrastructure for performing the steal lock
CCW program.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Set-pgid operations fail for some device types under z/VM for which
the hypervisor has already set the pgid. Also reserved devices or
changed pgids are not correctly recognized. Fix these problems by
using a combination of sense-pgid and set-pgid and by also accepting
pre-defined pgid settings.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Split setting (driver wants feature enabled) and status (feature
setup was successful) for PGID related ccw device features so that
setup errors can be detected. Previously, incorrectly handled setup
errors could in rare cases lead to erratic I/O behavior and
permanently unusuable devices.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After changing all internal I/O functions to use the newly introduced
ccw request infrastructure, retries are handled automatically after a
clear operation. Therefore remove the internal retry flag and
associated code.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Accept a request for setting a not-operational device offline.
This way, users can remove devices from Linux which would otherwise
remain unusable until reboot.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the newly introduced ccw request infrastructure to implement
pgid related operations: sense pgid, set pgid and disband pg.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Use the newly introduced ccw request infrastructure to implement
the sense id operation.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reduce code duplication by introducing a central infrastructure to
perform an internal I/O operation on a CCW device.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the call to BUG() for situations which are unexpected
but do not cause actual problems.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Device recognition needs to be started with the ccw device lock
held to prevent race conditions between I/O starting and interrupt
reception.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Handle verification errors consistently through the existing
callback ccw_device_done to reduce cleanup code duplication.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Remove the return code from ccw_device_recognition and handle
recognition errors through the existing callback
ccw_device_recog_done to reduce cleanup code duplication.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Print a warning message in case a ccw device enters boxed or
not operational state during online/offline processing.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Introduce a central mechanism for performing delayed ccw device work
to ensure that different types of work do not overwrite each other.
Prioritization ensures that the most important work is always
performed while less important tasks are either obsoleted or repeated
later.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Ensure that current and future users of sch->work do not overwrite
each other by introducing a single mechanism for delayed subchannel
work.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Change the initiative to update subchannel-ccw device associations
to the subchannel: when there is an indication that the internal
association no longer reflects the current hardware state, mark
each affected subchannel as requiring attention. Once processing
reaches a subchannel, determine the correct association for that
subchannel at that time and perform the necessary device_move
operations.
This change fixes problems with the previous approach which would
leave devices in an inconsistent state when a new hardware change
occurred while a device_move was already scheduled.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
sch_create_and_recog_new_device() associates a parent subchannel
with its ccw device child even though this is already done by
the subsequently called io_subchannel_recog(). Also make sure
io_subchannel_recog() sets the association under lock.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
io_subchannel_probe() frees memory for sch->private which is later
freed again when io_subchannel_remove() is called. Fix this problem
by removing the cleanup in io_subchannel_probe().
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When the kernel is IPLed without the CLEAR option and switches
to 64-bit, the high-order half of the registers might contain
random values. This can cause addressing exceptions and the
kernel enters an interrupt loop.
Initialize the high-order half of the general purpose registers
with zeros after switching to 64-bit mode.
Cc: <stable@kernel.org>
Signed-off-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
* 'x86-debug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Limit number of per cpu TSC sync messages
x86: dumpstack, 64-bit: Disable preemption when walking the IRQ/exception stacks
x86: dumpstack: Clean up the x86_stack_ids[][] initalization and other details
x86, cpu: mv display_cacheinfo -> cpu_detect_cache_sizes
x86: Suppress stack overrun message for init_task
x86: Fix cpu_devs[] initialization in early_cpu_init()
x86: Remove CPU cache size output for non-Intel too
x86: Minimise printk spew from per-vendor init code
x86: Remove the CPU cache size printk's
cpumask: Avoid cpumask_t in arch/x86/kernel/apic/nmi.c
x86: Make sure we also print a Code: line for show_regs()
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, msr, cpumask: Use struct cpumask rather than the deprecated cpumask_t
x86, cpuid: Simplify the code in cpuid_open
x86, cpuid: Remove the bkl from cpuid_open()
x86, msr: Remove the bkl from msr_open()
x86: AMD Geode LX optimizations
x86, msr: Unify rdmsr_on_cpus/wrmsr_on_cpus
* 'x86-cleanups-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Fix a section mismatch in arch/x86/kernel/setup.c
x86: Fixup last users of irq_chip->typename
x86: Remove BKL from apm_32
x86: Remove BKL from microcode
x86: use kernel_stack_pointer() in kprobes.c
x86: use kernel_stack_pointer() in kgdb.c
x86: use kernel_stack_pointer() in dumpstack.c
x86: use kernel_stack_pointer() in process_32.c
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
include/linux/compiler-gcc4.h: Fix build bug - gcc-4.0.2 doesn't understand __builtin_object_size
x86/alternatives: No need for alternatives-asm.h to re-invent stuff already in asm.h
x86/alternatives: Check replacementlen <= instrlen at build time
x86, 64-bit: Set data segments to null after switching to 64-bit mode
x86: Clean up the loadsegment() macro
x86: Optimize loadsegment()
x86: Add missing might_fault() checks to copy_{to,from}_user()
x86-64: __copy_from_user_inatomic() adjustments
x86: Remove unused thread_return label from switch_to()
x86, 64-bit: Fix bstep_iret jump
x86: Don't use the strict copy checks when branch profiling is in use
x86, 64-bit: Move K8 B step iret fixup to fault entry asm
x86: Generate cmpxchg build failures
x86: Add a Kconfig option to turn the copy_from_user warnings into errors
x86: Turn the copy_from_user check into an (optional) compile time warning
x86: Use __builtin_memset and __builtin_memcpy for memset/memcpy
x86: Use __builtin_object_size() to validate the buffer size for copy_from_user()
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
x86, apic: Enable lapic nmi watchdog on AMD Family 11h
x86: Remove unnecessary mdelay() from cpu_disable_common()
x86, ioapic: Document another case when level irq is seen as an edge
x86, ioapic: Fix the EOI register detection mechanism
x86, io-apic: Move the effort of clearing remoteIRR explicitly before migrating the irq
x86: SGI UV: Map low MMR ranges
x86: apic: Print out SRAT table APIC id in hex
x86: Re-get cfg_new in case reuse/move irq_desc
x86: apic: Remove not needed #ifdef
x86: io-apic: IO-APIC MMIO should not fail on resource insertion
x86: Remove asm/apicnum.h
x86: apic: Do not use stacked physid_mask_t
x86, apic: Get rid of apicid_to_cpu_present assign on 64-bit
x86, ioapic: Use snrpintf while set names for IO-APIC resourses
x86, apic: Use PAGE_SIZE instead of numbers
x86: Remove local_irq_enable()/local_irq_disable() in fixup_irqs()
x86: Use EOI register in io-apic on intel platforms
x86: Force irq complete move during cpu offline
x86: Remove move_cleanup_count from irq_cfg
x86, intr-remap: Avoid irq_chip mask/unmask in fixup_irqs() for intr-remapping
...
* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
tracing: Separate raw syscall from syscall tracer
ring-buffer-benchmark: Add parameters to set produce/consumer priorities
tracing, function tracer: Clean up strstrip() usage
ring-buffer benchmark: Run producer/consumer threads at nice +19
tracing: Remove the stale include/trace/power.h
tracing: Only print objcopy version warning once from recordmcount
tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
ring-buffer: Move access to commit_page up into function used
tracing: do not disable interrupts for trace_clock_local
ring-buffer: Add multiple iterations between benchmark timestamps
kprobes: Sanitize struct kretprobe_instance allocations
tracing: Fix to use __always_unused attribute
compiler: Introduce __always_unused
tracing: Exit with error if a weak function is used in recordmcount.pl
tracing: Move conditional into update_funcs() in recordmcount.pl
tracing: Add regex for weak functions in recordmcount.pl
tracing: Move mcount section search to front of loop in recordmcount.pl
tracing: Fix objcopy revision check in recordmcount.pl
tracing: Check absolute path of input file in recordmcount.pl
tracing: Correct the check for number of arguments in recordmcount.pl
...