This patch fixes a regression introduced by commit "MIPS: Alchemy: MTX-1:
Use linux gpio api." (bb706b28bb) which broke
PCI bus operation. The problem is caused by alchemy_gpio2_enable() which
resets the GPIO2 block. Two PCI signals (PCI_SERR and PCI_RST) are connected
to GPIO2 and they obviously do not to like the reset. Since GPIO2 is
correctly initialized by the boot monitor (YAMON) it is not necessary to
call this function, so just remove it.
Also replace gpio_set_value() with alchemy_gpio_set_value() to avoid
problems in case gpiolib gets initialized after PCI. And since alchemy
gpio_set_value() calls au_sync() we don't have to au_sync() again later.
Signed-off-by: Bruno Randolf <br1@einfach.org>
To: linux-mips@linux-mips.org
To: manuel.lauss@googlemail.com
Patchwork: https://patchwork.linux-mips.org/patch/1448/
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Quoting from Jiri Slaby's patch of a similar nature for x86:
When initrd is in use and a driver does request_module() in its
module_init (i.e. __initcall or device_initcall), a modprobe
process is created with VDSO mapping. But VDSO is inited even in
__initcall, i.e. on the same level (at the same time), so it may
not be inited yet (link order matters).
Move init_vdso up to subsys_initcall to avoid the issue.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Cc: Jiri Slaby <jslaby@suse.cz>
Patchwork: http://patchwork.linux-mips.org/patch/1386/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In addition to being useless, it was mis-spelled.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1385/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 4600 family code reads registers to differentiate between two ASIC
variants, but this was being done prior to the register setup. This moves
register setup before the reading code.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1392/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: sound/soc/au1x/snd-soc-au1xpsc-i2s.o(.data+0xa8): Section mismatch in reference from the variable au1xpsc_i2s_driver to the function .init.text:au1xpsc_i2s_drvprobe()
The variable au1xpsc_i2s_driver references
the function __init au1xpsc_i2s_drvprobe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/video/built-in.o(.data+0x360): Section mismatch in reference from the variable au1100fb_driver to the function .init.text:au1100fb_drv_probe()
The variable au1100fb_driver references
the function __init au1100fb_drv_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Fixing which triggers of a slew of further mismatches:
WARNING: drivers/video/built-in.o(.devinit.text+0xc0): Section mismatch in reference from the function au1100fb_drv_probe() to the variable .init.data:au1100fb_fix
The function __devinit au1100fb_drv_probe() references
a variable __initdata au1100fb_fix.
If au1100fb_fix is only used by au1100fb_drv_probe then
annotate au1100fb_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x21c): Section mismatch in reference from the function au1100fb_drv_probe() to the variable .init.data:au1100fb_var
The function __devinit au1100fb_drv_probe() references
a variable __initdata au1100fb_var.
If au1100fb_var is only used by au1100fb_drv_probe then
annotate au1100fb_var with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/built-in.o(.devinit.text+0xc0): Section mismatch in reference from the function pmagbafb_probe() to the variable .init.data:pmagbafb_fix
The function __devinit pmagbafb_probe() references
a variable __initdata pmagbafb_fix.
If pmagbafb_fix is only used by pmagbafb_probe then
annotate pmagbafb_fix with a matching annotation.
Fixing this one triggers a few more mismatches in order:
WARNING: drivers/video/built-in.o(.devinit.text+0x414): Section mismatch in reference from the function pmagbbfb_probe() to the variable .init.data:pmagbbfb_fix
The function __devinit pmagbbfb_probe() references
a variable __initdata pmagbbfb_fix.
If pmagbbfb_fix is only used by pmagbbfb_probe then
annotate pmagbbfb_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x45c): Section mismatch in reference from the function pmagbbfb_probe() to the variable .init.data:pmagbbfb_defined
The function __devinit pmagbbfb_probe() references
a variable __initdata pmagbbfb_defined.
If pmagbbfb_defined is only used by pmagbbfb_probe then
annotate pmagbbfb_defined with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x5fc): Section mismatch in reference from the function pmagbbfb_probe() to the function .init.text:pmagbbfb_screen_setup()
The function __devinit pmagbbfb_probe() references
a function __init pmagbbfb_screen_setup().
If pmagbbfb_screen_setup is only used by pmagbbfb_probe then
annotate pmagbbfb_screen_setup with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x6f4): Section mismatch in reference from the function pmagbbfb_probe() to the function .init.text:pmagbbfb_osc_setup()
The function __devinit pmagbbfb_probe() references
a function __init pmagbbfb_osc_setup().
If pmagbbfb_osc_setup is only used by pmagbbfb_probe then
annotate pmagbbfb_osc_setup with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x5f8): Section mismatch in reference from the function pmagbbfb_osc_setup() to the variable .init.data:pmagbbfb_freqs.15993
The function __devinit pmagbbfb_osc_setup() references
a variable __initdata pmagbbfb_freqs.15993.
If pmagbbfb_freqs.15993 is only used by pmagbbfb_osc_setup then
annotate pmagbbfb_freqs.15993 with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/video/built-in.o(.data+0x1e0): Section mismatch in reference fr
om the variable pmagbafb_driver to the function .init.text:pmagbafb_probe()
The variable pmagbafb_driver references
the function __init pmagbafb_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Fixing this one triggers 2 more:
WARNING: drivers/video/built-in.o(.devinit.text+0xc0): Section mismatch in reference from the function pmagbafb_probe() to the variable .init.data:pmagbafb_fix
The function __devinit pmagbafb_probe() references
a variable __initdata pmagbafb_fix.
If pmagbafb_fix is only used by pmagbafb_probe then
annotate pmagbafb_fix with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x108): Section mismatch in reference from the function pmagbafb_probe() to the variable .init.data:pmagbafb_defined
The function __devinit pmagbafb_probe() references
a variable __initdata pmagbafb_defined.
If pmagbafb_defined is only used by pmagbafb_probe then
annotate pmagbafb_defined with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/net/built-in.o(.data+0x24): Section mismatch in reference from
the variable dec_lance_tc_driver to the function .init.text:dec_lance_tc_probe()
The variable dec_lance_tc_driver references
the function __init dec_lance_tc_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Fixing this one results in a new mismatch:
WARNING: drivers/net/built-in.o(.devinit.text+0x14): Section mismatch in reference from the function dec_lance_tc_probe() to the function .init.text:dec_lance_probe()
The function __devinit dec_lance_tc_probe() references
a function __init dec_lance_probe().
If dec_lance_probe is only used by dec_lance_tc_probe then
annotate dec_lance_probe with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
WARNING: drivers/video/built-in.o(.devinit.text+0x54): Section mismatch in reference from the function gbefb_probe() to the function .init.text:gbefb_setup()
The function __devinit gbefb_probe() references
a function __init gbefb_setup().
If gbefb_setup is only used by gbefb_probe then
annotate gbefb_setup with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x208): Section mismatch in reference from the function gbefb_probe() to the variable .init.data:mode_option
The function __devinit gbefb_probe() references
a variable __initdata mode_option.
If mode_option is only used by gbefb_probe then
annotate mode_option with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x214): Section mismatch in reference from the function gbefb_probe() to the variable .init.data:default_mode
The function __devinit gbefb_probe() references
a variable __initdata default_mode.
If default_mode is only used by gbefb_probe then
annotate default_mode with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x23c): Section mismatch in reference from the function gbefb_probe() to the variable .init.data:default_var
The function __devinit gbefb_probe() references
a variable __initdata default_var.
If default_var is only used by gbefb_probe then
annotate default_var with a matching annotation.
Fixing these results in more mismatches:
WARNING: drivers/video/built-in.o(.devinit.text+0x3c): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_var_LCD
The function __devinit gbefb_setup() references
a variable __initdata default_var_LCD.
If default_var_LCD is only used by gbefb_setup then
annotate default_var_LCD with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x14c): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_mode_LCD
The function __devinit gbefb_setup() references
a variable __initdata default_mode_LCD.
If default_mode_LCD is only used by gbefb_setup then
annotate default_mode_LCD with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x150): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_var_CRT
The function __devinit gbefb_setup() references
a variable __initdata default_var_CRT.
If default_var_CRT is only used by gbefb_setup then
annotate default_var_CRT with a matching annotation.
WARNING: drivers/video/built-in.o(.devinit.text+0x154): Section mismatch in reference from the function gbefb_setup() to the variable .init.data:default_mode_CRT
The function __devinit gbefb_setup() references
a variable __initdata default_mode_CRT.
If default_mode_CRT is only used by gbefb_setup then
annotate default_mode_CRT with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
nconfig: Fix segfault when help contains special characters
kbuild: Fix make rpm
kbuild: Make the setlocalversion script POSIX-compliant
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Fix fallback to cplus_demangle() when bfd_demangle() is not available
perf annotate: Fix handling of goto labels that are valid hex numbers
tracing: Properly align linker defined symbols
perf symbols: Fix directory descriptor leaking
perf: Fix various display bugs with parent filtering
nconfig segfaults when help text contains the character '%'. For a quick
example, navigate to the kernel compression options and get the help for
bzip2. Doing so triggers a call to mvwprintw() with a string containing
'%' and no extra arguments to fill in the specifier's value. Fix this
case by printing the literal string retrieved from the kconfig.
#0 0x00002b52b6b11d83 in vfprintf () from /lib/libc.so.6
#1 0x00002b52b6bad010 in __vsnprintf_chk () from /lib/libc.so.6
#2 0x00002b52b623991b in _nc_printf_string () from
/lib/libncursesw.so.5
#3 0x00002b52b6234cff in vwprintw () from /lib/libncursesw.so.5
#4 0x00002b52b6234db9 in mvwprintw () from /lib/libncursesw.so.5
#5 0x00000000004151d8 in fill_window (win=0x21b64c0,
text=0x21b62b0 "CONFIG_KERNEL_BZIP2:\n\nIts compression ratio and
speed is intermediate.\nDecompression speed is slowest among the
three. The kernel\nsize is about 10% smaller with bzip2, in
comparison to gzip.\nBzip2 us"...)
at scripts/kconfig/nconf.gui.c:229
#6 0x0000000000416335 in show_scroll_win (main_window=0x21a5630,
title=0x157fa30 "Bzip2",
text=0x21b62b0 "CONFIG_KERNEL_BZIP2:\n\nIts compression
ratio and speed is intermediate.\nDecompression speed is
slowest among the three. The kernel\nsize is about 10%
smaller with bzip2, in comparison to gzip.\nBzip2 us"...)
at scripts/kconfig/nconf.gui.c:535
#7 0x00000000004055b2 in show_help (menu=0x157f9d0)
at scripts/kconfig/nconf.c:1257
#8 0x0000000000405897 in conf_choice (menu=0x157f130)
at scripts/kconfig/nconf.c:1321
#9 0x0000000000405326 in conf (menu=0x157d130) at
scripts/kconfig/nconf.c:1208
#10 0x00000000004052e8 in conf (menu=0xb434a0) at
scripts/kconfig/nconf.c:1203
#11 0x0000000000406092 in main (ac=2, av=0x7fff96a93c38)
Cc: Michal Marek <mmarek@suse.cz>
Cc: Nir Tzachar <nir.tzachar@gmail.com>
Signed-off-by: Stephen Boyd <bebarino@gmail.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
The .data..init_task output section was missing
a load offset causing a popwerpc target to fail to boot.
Sean MacLennan tracked it down to the definition of
INIT_TASK_DATA_SECTION().
There are only two users of INIT_TASK_DATA_SECTION()
in the kernel today: cris and popwerpc.
cris do not support relocatable kernels and is thus not
impacted by this change.
Fix INIT_TASK_DATA_SECTION() to specify load offset like
all other output sections.
Reported-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Oooops... we missed these. We incorrectly converted strings
used when parsing the device-tree on pseries, thus breaking
access to drconf memory and hotplug memory.
While at it, also revert some variable names that represent
something the FW calls "lmb" and thus don't need to be converted
to "memblock".
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
This adds some debug output to our MMU hash code to print out some
useful debug data if the hypervisor refuses the insertion (which
should normally never happen).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
There's a couple of nasty bugs lurking in our huge page hashing code.
First, we don't check the access permission atomically with setting
the _PAGE_BUSY bit, which means that the PTE value we end up using
for the hashing might be different than the one we have checked
the access permissions for.
We've seen cases where that leads us to try to use an invalidated
PTE for hashing, causing all sort of "interesting" issues.
Then, we also failed to set _PAGE_DIRTY on a write access.
Finally, a minor tweak but we should return 0 when we find the
PTE busy, in order to just re-execute the access, rather than 1
which means going to do_page_fault().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
Instead of adding _PAGE_PRESENT to the access permission mask
in each low level routine independently, we add it once from
hash_page().
We also move the preliminary access check (the racy one before
the PTE is locked) up so it applies to the huge page case. This
duplicates code in __hash_page_huge() which we'll remove in a
subsequent patch to fix a race in there.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If the hypervisor gives us an error on a hugepage insert we panic. The
normal page code already handles this by returning an error instead and we end
calling low_hash_fault which will just kill the task if possible.
The patch below does a similar thing for the hugepage case.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
make version 3.80 doesn't support "else ifdef" on the same line, also it
doesn't support unindented nested constructs.
Build fails with:
Makefile:608: Extraneous text after `else' directive
Makefile:611: *** only one `else' per conditional. Stop.
This patch fixes the build for make 3.80.
Cc: Ingo Molnar <mingo@elte.hu>,
Cc: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1278430783-17259-1-git-send-email-conny.seidel@amd.com>
Signed-off-by: Conny Seidel <conny.seidel@amd.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - relax capability ID checks on newer hardware
Input: twl40300-keypad - fix handling of "all ground" rows
Input: gamecon - reference correct pad in gc_psx_command()
Input: gamecon - reference correct input device in NES mode
Input: w90p910_keypad - change platfrom driver name to 'nuc900-kpi'
Input: i8042 - add Gigabyte Spring Peak to dmi_noloop_table
Input: qt2160 - rename kconfig symbol name
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: add quirk to make HP DV5000 laptop resume
drm/radeon/kms: fix RADEON_INFO_CRTC_FROM_ID info ioctl
Fix ttm_page_alloc.c build breakage
drm/radeon/kms: fix legacy LVDS dpms sequence
drm/radeon/kms: drop taking lock around crtc lookup.
* 'x86/auditsyscall' of git://git.kernel.org/pub/scm/linux/kernel/git/frob/linux-2.6-roland:
x86: auditsyscall: fix fastpath return value after reschedule
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
sysrq,kdb: Use __handle_sysrq() for kdb's sysrq function
debug_core,kdb: fix kgdb_connected bit set in the wrong place
Fix merge regression from external kdb to upstream kdb
repair gdbstub to match the gdbserial protocol specification
kdb: break out of kdb_ll() when command is terminated
The KEXEC_*_MEMORY_LIMITs are inclusive addresses. We define them as
2Gs as that is what we allow mapping via TLBs. However, this should be
2G - 1 to be inclusive, otherwise if we have >2G of memory in a system
we fail to boot properly via kexec.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When parsing the objdump disassembly output we can have goto labels that
are valid hex numbers and thus get confused with lines with machine
code.
Handle the common case of a label that has nothing after it and other
cases where there is just source code by validating the resulting "ip".
It is still possible that we find goto labels that are in the function
address range, but only if they are located before the real address we
should be OK.
A change in the objdump output to have a clear marker separating
addresses from the disassembly would come handy, but we would still have
to deal with older versions.
Reported-by: Gleb Natapov <gleb@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
LKML-Reference: <20100722170541.GF17631@ghostprotocols.net>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix the security problem in the CIFS filesystem DNS lookup code in which a
malicious redirect could be installed by a random user by simply adding a
result record into one of their keyrings with add_key() and then invoking a
CIFS CFS lookup [CVE-2010-2524].
This is done by creating an internal keyring specifically for the caching of
DNS lookups. To enforce the use of this keyring, the module init routine
creates a set of override credentials with the keyring installed as the thread
keyring and instructs request_key() to only install lookup result keys in that
keyring.
The override is then applied around the call to request_key().
This has some additional benefits when a kernel service uses this module to
request a key:
(1) The result keys are owned by root, not the user that caused the lookup.
(2) The result keys don't pop up in the user's keyrings.
(3) The result keys don't come out of the quota of the user that caused the
lookup.
The keyring can be viewed as root by doing cat /proc/keys:
2a0ca6c3 I----- 1 perm 1f030000 0 0 keyring .dns_resolver: 1/4
It can then be listed with 'keyctl list' by root.
# keyctl list 0x2a0ca6c3
1 key in keyring:
726766307: --alswrv 0 0 dns_resolver: foo.bar.com
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-and-Tested-by: Jeff Layton <jlayton@redhat.com>
Acked-by: Steve French <smfrench@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=29062
Reported-by: Andres Cimmarusti <acimmarusti@gmail.com>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Older firmwares fixed the middle byte of the Synaptics capabilities
query to 0x47, but starting with firmware 7.5 the middle byte
represents submodel ID, sometimes also called "dash number".
Reported-and-tested-by: Miroslav Šulc <fordfrog@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In the CONFIG_AUDITSYSCALL fast-path for x86 64-bit system calls,
we can pass a bad return value and/or error indication for the
system call to audit_syscall_exit(). This happens when
TIF_NEED_RESCHED was set as the system call returned, so we went
out to schedule() and came back to the exit-audit fast-path. The
fix is to reload the user return value register from the pt_regs
before using it for audit_syscall_exit().
Both the 32-bit kernel's fast path and the 64-bit kernel's 32-bit
system call fast paths work slightly differently, so that they
always leave the fast path entirely to reschedule and don't return
there, so they don't have the analogous bugs.
Reported-by: Alexander Viro <aviro@redhat.com>
Signed-off-by: Roland McGrath <roland@redhat.com>
The kdb code should not toggle the sysrq state in case an end user
wants to try and resume the normal kernel execution.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Immediately following an exit from the kdb shell the kgdb_connected
variable should be set to zero, unless there are breakpoints planted.
If the kgdb_connected variable is not zeroed out with kdb, it is
impossible to turn off kdb.
This patch is merely a work around for now, the real fix will check
for the breakpoints.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
In the process of merging kdb to the mainline, the kdb lsmod command
stopped printing the base load address of kernel modules. This is
needed for using kdb in conjunction with external tools such as gdb.
Simply restore the functionality by adding a kdb_printf for the base
load address of the kernel modules.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
The gdbserial protocol handler should return an empty packet instead
of an error string when ever it responds to a command it does not
implement.
The problem cases come from a debugger client sending
qTBuffer, qTStatus, qSearch, qSupported.
The incorrect response from the gdbstub leads the debugger clients to
not function correctly. Recent versions of gdb will not detach correctly as a result of this behavior.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Dongdong Deng <dongdong.deng@windriver.com>
Without this patch the "ll" linked-list traversal command won't
terminate when you hit q/Q.
Signed-off-by: Martin Hicks <mort@sgi.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Return the crtc_id, not the counter value. They are not
necessarily the same.
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The commit 1e8655f873
drm/ttm: Fix build on architectures without AGP
looks at TTM_HAS_AGP before it has been set in ttm_bo_driver.h
Move the conditional inclusion of <asm/agp.h> *after* we have included
ttm_bo_driver.h
Signed-of-by: Tony Luck <tony.luck@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add delay after turning off the LVDS encoder.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=16389
Tested-by: Jan Kreuzer <kontrollator@gmx.de>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We only add/remove crtcs at driver load, you cannot remove when
the GPU is running a CS packet since the fd is open, when
GPU hotplugging on radeons actually is needed all this locking
needs a review and I've started re-working kms core locking to deal
with this better. But for now avoid long delays in CS processing when
hotplug detect is happening in a different thread.
this fixes a regression introduced with hotplug detection.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'fix/asoc' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: Select wm_hubs automatically for WM8994
ASoC: Remove duplicate AUX definition from WM8776
ASoC:: remove a redundant snd_soc_unregister_codec call in wm8988_register
ASoC: wm8727: add a missing return in wm8727_platform_probe
ASoC: fsi: fixup wrong value setting order of TDM
ASoC: fsi: fixup clock inversion operation
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
math-emu: correct test for downshifting fraction in _FP_FROM_INT()
perf: Add DWARF register lookup for sparc
MAINTAINERS: Add SBUS driver path to sparc entry.
drivers/sbus: Remove unnecessary casts of private_data
sparc: remove homegrown L1_CACHE_ALIGN macro
sparc64: fix the build error due to smp_kgdb_capture_client()
sparc64: Fix maybe_change_configuration() PCR setting.
arch/sparc/kernel: Eliminate what looks like a NULL pointer dereference
sparc64: Update defconfig.
sunsu: Fix use after free in su_remove().
sunserial: Don't call add_preferred_console() when console= is specified.
sparc32: Kill none_mask, it's bogus.
Pointed out by Lucas who found the new one in a comment in
setup_percpu.c. And then I fixed the others that I grepped
for.
Reported-by: Lucas <canolucas@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
make rpm was broken by commit 0915512:
make clean
set -e; cd ..; ln -sf /usr/src/iwlwifi-2.6 kernel-2.6.35rc4wl
/bin/sh /usr/src/iwlwifi-2.6/scripts/setlocalversion --scm-only >
/usr/src/iwlwifi-2.6/.scmversion
cat: .scmversion: input file is output file
make[1]: *** [rpm] Error 1
Reported-and-tested-by: "Zheng, Jiajia" <jiajia.zheng@intel.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Up to 2.6.34 pcmcia_release_irq() reset p_dev->_irq to 0 after releasing
the irq. The IRQ is now released in pcmcia_disable_device(), however
p_dev->_irq is not reset, triggering a warning in pcmcia_device_remove().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
