Commit 88491d8(drivers/net: Kconfig & Makefile cleanup) causes a
regression that netconsole does not work if netconsole and network
device driver are build into kernel, because netconsole is linked
before network device driver.
Andrew Morton suggested to fix this with initcall ordering.
Fixes it by switching init_netconsole() to late_initcall.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function may currently fill one entry beyond the end of the
array it is given. It also doesn't return an error code in case
it does detect overflow.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using MLPPP, the maximum size of a fragment is incorrectly
calculated with an offset of -2.
This patch reverses the changes in the patch found here:
http://marc.info/?l=linux-netdev&m=123541324010539&w=2
The value of hdrlen includes the size of both the 2-byte PPP protocol
field and the 2- or 4-byte multilink header (2+4=6 for long sequence
numbers, 2+2=4 for short sequence numbers). Section 2 of RFC1661 says
that the MRU that is negotiated (i.e., the MTU of the sending system)
includes only the PPP payload but not the protocol field, thus the
correct MTU should be the link's MTU minus the multilink header (mtu -
(hdrlen-2)).
The incorrect calculation causes Linux to fragment packets to a size two
bytes smaller than the allowed MTU. While not technically illegal, this
behaviour confounds MRU-tuning to avoid PPP-layer fragmentation.
Signed-off-by: Henry Wong <henry@stuffedcow.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GRETH GBIT core does not do checksum offloading for IP
segmentation. This patch adds a check in the xmit function to
determine if the stack has calculated the checksum for us.
Signed-off-by: Daniel Hellstrom <daniel@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling snmp6_alloc_dev fails, the snmp6 relevant memory
are freed by snmp6_alloc_dev. Calling in6_dev_finish_destroy
will free these memory twice.
Double free will lead that undefined behavior occurs.
Signed-off-by: Roy Li <rongqing.li@windriver.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'irq-fixes-for-linus' of git://tesla.tglx.de/git/linux-2.6-tip:
x86, iommu: Mark DMAR IRQ as non-threaded
genirq: Make irq_shutdown() symmetric vs. irq_startup again
* 'for-linus' of git://github.com/chrismason/linux:
Btrfs: only clear the need lookup flag after the dentry is setup
BTRFS: Fix lseek return value for error
Btrfs: don't change inode flag of the dest clone file
Btrfs: don't make a file partly checksummed through file clone
Btrfs: fix pages truncation in btrfs_ioctl_clone()
btrfs: fix d_off in the first dirent
When a xHC host is unable to handle isochronous transfer in the
interval, it reports a Missed Service Error event and skips some tds.
Currently xhci driver handles MSE event in the following ways:
1. When encounter a MSE event, set ep->skip flag, update event ring
dequeue pointer and return.
2. When encounter the next event on this ep, the driver will run the
do-while loop, fetch td from ep's td_list to find the td
corresponding to this event. All tds missed are marked as short
transfer(-EXDEV).
The do-while loop will end in two ways:
1. If the td pointed by the event trb is found;
2. If the ep ring's td_list is empty.
However, if a buggy HW reports some unpredicted event (for example, an
overrun event following a MSE event while the ep ring is actually not
empty), the driver will never find the td, and it will loop until the
td_list is empty.
Unfortunately, the spinlock is dropped when give back a urb in the
do-while loop. During the spinlock released period, the class driver
may still submit urbs and add tds to the td_list. This may cause
disaster, since the td_list will never be empty and the loop never ends,
and the system hangs.
To fix this, count the number of TDs on the ep ring before skipping TDs,
and quit the loop when skipped that number of tds. This guarantees the
do-while loop will end after certain number of cycles, and driver will
not be trapped in an infinite loop.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Sometimes, when a USB 3.0 device is disconnected, the Intel Panther
Point xHCI host controller will report a link state change with the
state set to "SS.Inactive". This causes the xHCI host controller to
issue a warm port reset, which doesn't finish before the USB core times
out while waiting for it to complete.
When the warm port reset does complete, and the xHC gives back a port
status change event, the xHCI driver kicks khubd. However, it fails to
set the bit indicating there is a change event for that port because the
logic in xhci-hub.c doesn't check for the warm port reset bit.
After that, the warm port status change bit is never cleared by the USB
core, and the xHC stops reporting port status change bits. (The xHCI
spec says it shouldn't report more port events until all change bits are
cleared.) This means any port changes when a new device is connected
will never be reported, and the port will seem "dead" until the xHCI
driver is unloaded and reloaded, or the computer is rebooted. Fix this
by making the xHCI driver set the port change bit when a warm port reset
change bit is set.
A better solution would be to make the USB core handle warm port reset
in differently, merging the current code with the standard port reset
code that does an incremental backoff on the timeout, and tries to
complete the port reset two more times before giving up. That more
complicated fix will be merged next window, and this fix will be
backported to stable.
This should be backported to kernels as old as 3.0, since that was the
first kernel with commit a11496ebf3 ("xHCI: warm reset support").
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix build when CONFIG_ISA_DMA_API is enabled but
CONFIG_COMEDI_PCI[_DRIVERS] is not enabled.
Fixes these build errors:
drivers/staging/comedi/drivers/ni_labpc.c: In function 'labpc_ai_cmd':
drivers/staging/comedi/drivers/ni_labpc.c:1351: error: implicit declaration of function 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c: At top level:
drivers/staging/comedi/drivers/ni_labpc.c:1802: error: conflicting types for 'labpc_suggest_transfer_size'
drivers/staging/comedi/drivers/ni_labpc.c:1351: note: previous implicit declaration of 'labpc_suggest_transfer_size' was here
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Even with just the interface limited to admin, there really is little to
reason to give byte-per-byte counts for taskstats. So round it down to
something less intrusive.
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ok, this isn't optimal, since it means that 'iotop' needs admin
capabilities, and we may have to work on this some more. But at the
same time it is very much not acceptable to let anybody just read
anybody elses IO statistics quite at this level.
Use of the GENL_ADMIN_PERM suggested by Johannes Berg as an alternative
to checking the capabilities by hand.
Reported-by: Vasiliy Kulikov <segoon@openwall.com>
Cc: Johannes Berg <johannes.berg@intel.com>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In ad-hoc mode, driver b43 does not issue beacons.
Signed-off-by: Manual Munz <freifunk@somakoma.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/radeon/kms: Make GPU/CPU page size handling consistent in blit code (v2)
drm/radeon/kms: fix typo in r100_blit_copy
drm/radeon: Unreference GEM object outside of spinlock in page flip error path.
drm/radeon: Don't read from CP ring write pointer registers.
drm/ttm: request zeroed system memory pages for new TT buffer objects
D-SACK is allowed to reside below snd_una. But the corresponding check
in tcp_is_sackblock_valid() is the exact opposite. It looks like a typo.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 946cedccbd (tcp: Change possible SYN flooding messages)
added a build error if CONFIG_SYN_COOKIES=n
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.infradead.org/users/sameo/mfd-2.6:
mfd: Fix omap-usb-host build failure
mfd: Make omap-usb-host TLL mode work again
mfd: Set MAX8997 irq pointer
mfd: Fix initialisation of tps65910 interrupts
mfd: Check for twl4030-madc NULL pointer
mfd: Copy the device pointer to the twl4030-madc structure
mfd: Rename wm8350 static gpio_set_debounce()
mfd: Fix value of WM8994_CONFIGURE_GPIO
The BO blit code inconsistenly handled the page size. This wasn't
an issue on system with 4k pages since the GPU's page size is 4k as
well. Switch the driver blit callbacks to take num pages in GPU
page units.
Fixes lemote mipsel systems using AMD rs780/rs880 chipsets.
v2: incorporate suggestions from Michel.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
cur_pages is the number of pages per loop iteration.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Michel Dänzer <michel.daenzer@amd.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
* git://github.com/davem330/net: (62 commits)
ipv6: don't use inetpeer to store metrics for routes.
can: ti_hecc: include linux/io.h
IRDA: Fix global type conflicts in net/irda/irsysctl.c v2
net: Handle different key sizes between address families in flow cache
net: Align AF-specific flowi structs to long
ipv4: Fix fib_info->fib_metrics leak
caif: fix a potential NULL dereference
sctp: deal with multiple COOKIE_ECHO chunks
ibmveth: Fix checksum offload failure handling
ibmveth: Checksum offload is always disabled
ibmveth: Fix issue with DMA mapping failure
ibmveth: Fix DMA unmap error
pch_gbe: support ML7831 IOH
pch_gbe: added the process of FIFO over run error
pch_gbe: fixed the issue which receives an unnecessary packet.
sfc: Use 64-bit writes for TX push where possible
Revert "sfc: Use write-combining to reduce TX latency" and follow-ups
bnx2x: Fix ethtool advertisement
bnx2x: Fix 578xx link LED
bnx2x: Fix XMAC loopback test
...
We can race with readdir and the RCU path walking stuff. This is because we
clear the need lookup flag before actually instantiating the inode. This will
lead the RCU path walk stuff to find a dentry it thinks is valid without a
d_inode attached. So instead unhash the dentry when we first start the lookup,
and then clear the flag after we've instantiated the dentry so we're garunteed
to either try the slow lookup, or have the d_inode set properly.
Signed-off-by: Josef Bacik <josef@redhat.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The recent reworking of btrfs' lseek lead to incorrect
values being returned. This adds checks for seeking
beyond EOF in SEEK_HOLE and makes sure the error
values come back correct.
Andi Kleen also sent in similar patches.
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Reported-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
The dst file will have the same inode flags with dst file after
file clone, and I think it's unexpected.
For example, the dst file will suddenly become immutable after
getting some share of data with src file, if the src is immutable.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
To reproduce the bug:
# mount /dev/sda7 /mnt
# dd if=/dev/zero of=/mnt/src bs=4K count=1
# umount /mnt
# mount -o nodatasum /dev/sda7 /mnt
# dd if=/dev/zero of=/mnt/dst bs=4K count=1
# clone_range -s 4K -l 4K /mnt/src /mnt/dst
# echo 3 > /proc/sys/vm/drop_caches
# cat /mnt/dst
# dmesg
...
btrfs no csum found for inode 258 start 0
btrfs csum failed ino 258 off 0 csum 2566472073 private 0
It's because part of the file is checksummed and the other part is not,
and then btrfs will complain checksum is not found when we read the file.
Disallow file clone if src and dst file have different checksum flag,
so we ensure a file is completely checksummed or unchecksummed.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
It's a bug in commit f81c9cdc56
(Btrfs: truncate pages from clone ioctl target range)
We should pass the dest range to the truncate function, but not the
src range.
Also move the function before locking extent state.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
Since the d_off in the first dirent for "." (that originates from
the 4th argument "offset" of filldir() for the 2nd dirent for "..")
is wrongly assigned in btrfs_real_readdir(), telldir returns same
offset for different locations.
| # mkfs.btrfs /dev/sdb1
| # mount /dev/sdb1 fs0
| # cd fs0
| # touch file0 file1
| # ../test
| telldir: 0
| readdir: d_off = 2, d_name = "."
| telldir: 2
| readdir: d_off = 2, d_name = ".."
| telldir: 2
| readdir: d_off = 3, d_name = "file0"
| telldir: 3
| readdir: d_off = 2147483647, d_name = "file1"
| telldir: 2147483647
To fix this problem, pass filp->f_pos (which is loff_t) instead.
| # ../test
| telldir: 0
| readdir: d_off = 1, d_name = "."
| telldir: 1
| readdir: d_off = 2, d_name = ".."
| telldir: 2
| readdir: d_off = 3, d_name = "file0"
:
At the moment the "offset" for "." is unused because there is no
preceding dirent, however it is better to pass filp->f_pos to follow
grammatical usage.
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Chris Mason <chris.mason@oracle.com>
* '3.1-rc-fixes' of git://linux-iscsi.org/target-pending:
iscsi-target: Fix sendpage breakage with proper padding+DataDigest iovec offsets
iscsi-target: Disable markers + remove dangerous local scope array usage
target: Skip non hex characters for VPD=0x83 NAA IEEE Registered Extended
tcm_fc: Work queue based approach instead of managing own thread and event based mechanism
tcm_fc: Invalidation of DDP context for FCoE target in error conditions
target: Fix race between multiple invocations of target_qf_do_work()
Today I noticed that the usb bluetooth adapter (BCM2046B1) on my 2011
mac mini was not working. I've created a patch to get it going.
Signed-off-by: Jurgen Kramer <gtmkramer@xs4all.nl>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
This patch against current git adds the hardware ID for the Apple
MacBookAir4,1, released in July 2011. The device features a BCM2046
USB chip. The patch was inspired by the previous modifications adding
support for the MacBookAir3,x.
Signed-off-by: Pieter-Augustijn Van Malleghem <p-a@scarlet.be>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Reordered the BT ST channel registration, to make sure that the
event channel is registered before all others. This prevents a
situation where incoming events may cause kernel panic in the ST
driver if the event channel is not yet registered to handle
incoming events.In addition, the deregistration of the channels
was also modified, to be in the reversed order of the registration,
to allow the event channel to be the last one unregistered.
Signed-off-by: Chen Ganir <chen.ganir@ti.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
The TBI bit in PHYStatus is reserved on anything but the oldest 8169.
Nobody complained after I disabled it for the 8168 and the 810x (see
66ec5d4fb1).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
Current IPv6 implementation uses inetpeer to store metrics for
routes. The problem of inetpeer is that it doesn't take subnet
prefix length in to consideration. If two routes have the same
address but different prefix length, they share same inetpeer.
So changing metrics of one route also affects the other. The
fix is to allocate separate metrics storage for each route.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug in the iscsit_fe_sendpage_sg() transmit codepath that
was originally introduced with the v3.1 iscsi-target merge that incorrectly
uses hardcoded cmd->iov_data_count values to determine cmd->iov_data[] offsets
for extra outgoing padding and DataDigest payload vectors.
This code is obviously incorrect for the DataDigest enabled case with sendpage
offload, and this fix ensures correct operation for padding + DataDigest,
padding only, and DataDigest only cases. The bug was introduced during a
pre-merge change in iscsit_fe_sendpage_sg() to natively use struct scatterlist
instead of the legacy v3.0 struct se_mem logic.
Cc: Andy Grover <agrover@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This fixes a build breakage for OMAP3 boards.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: netdev@vger.kernel.org
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The externs here didn't agree with the declarations in qos.c.
Better would be probably to move this into a header, but since it's
common practice to have naked externs with sysctls I left it for now.
Cc: samuel@sortiz.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the conversion of struct flowi to a union of AF-specific structs, some
operations on the flow cache need to account for the exact size of the key.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
AF-specific flowi structs are now passed to flow_key_compare, which must
also be aligned to a long.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4670994d(net,rcu: convert call_rcu(fc_rport_free_rcu) to
kfree_rcu()) introduced a memory leak. This patch reverts it.
Signed-off-by: Zheng Yan <zheng.z.yan@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
