* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6: (36 commits)
jsm: fixing error if the driver fails to load
jsm: removing the uart structure and filename on error
tty: Add a new VT mode which is like VT_PROCESS but doesn't require a VT_RELDISP ioctl call
tty: Keep the default buffering to sub-page units
tty: Fix up char drivers request_room usage
tty: Fix the ldisc hangup race
serial: timberdale: Remove dependancies
nozomi: Tidy up the PCI table
nozomi: Fix mutex handling
nozomi: Add tty_port usage
sdio_uart: Use kfifo instead of the messy circ stuff
serial: bcm63xx_uart: allow more than one uart to be registered.
serial: bcm63xx_uart: don't use kfree() on non kmalloced area.
serial: bfin_5xx: pull in linux/io.h for ioremap prototypes
serial: bfin_5xx: kgdboc should accept gdb break only when it is active
serial: bfin_5xx: need to disable DMA TX interrupt too
serial: bfin_5xx: remove useless gpio handling with hard flow control
Char: synclink, remove unnecessary checks
tty: declare MODULE_FIRMWARE in various drivers
ip2: Add module parameter.
...
* 'x86-apic-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (25 commits)
x86: Fix out of order of gsi
x86: apic: Fix mismerge, add arch_probe_nr_irqs() again
x86, irq: Keep chip_data in create_irq_nr and destroy_irq
xen: Remove unnecessary arch specific xen irq functions.
smp: Use nr_cpus= to set nr_cpu_ids early
x86, irq: Remove arch_probe_nr_irqs
sparseirq: Use radix_tree instead of ptrs array
sparseirq: Change irq_desc_ptrs to static
init: Move radix_tree_init() early
irq: Remove unnecessary bootmem code
x86: Add iMac9,1 to pci_reboot_dmi_table
x86: Convert i8259_lock to raw_spinlock
x86: Convert nmi_lock to raw_spinlock
x86: Convert ioapic_lock and vector_lock to raw_spinlock
x86: Avoid race condition in pci_enable_msix()
x86: Fix SCI on IOAPIC != 0
x86, ia32_aout: do not kill argument mapping
x86, irq: Move __setup_vector_irq() before the first irq enable in cpu online path
x86, irq: Update the vector domain for legacy irqs handled by io-apic
x86, irq: Don't block IRQ0_VECTOR..IRQ15_VECTOR's on all cpu's
...
* 'x86-bootmem-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (30 commits)
early_res: Need to save the allocation name in drop_range_partial()
sparsemem: Fix compilation on PowerPC
early_res: Add free_early_partial()
x86: Fix non-bootmem compilation on PowerPC
core: Move early_res from arch/x86 to kernel/
x86: Add find_fw_memmap_area
Move round_up/down to kernel.h
x86: Make 32bit support NO_BOOTMEM
early_res: Enhance check_and_double_early_res
x86: Move back find_e820_area to e820.c
x86: Add find_early_area_size
x86: Separate early_res related code from e820.c
x86: Move bios page reserve early to head32/64.c
sparsemem: Put mem map for one node together.
sparsemem: Put usemap for one node together
x86: Make 64 bit use early_res instead of bootmem before slab
x86: Only call dma32_reserve_bootmem 64bit !CONFIG_NUMA
x86: Make early_node_mem get mem > 4 GB if possible
x86: Dynamically increase early_res array size
x86: Introduce max_early_res and early_res_count
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ieee1394/linux1394-2.6: (23 commits)
firewire: ohci: extend initialization log message
firewire: ohci: fix IR/IT context mask mixup
firewire: ohci: add module parameter to activate quirk fixes
firewire: ohci: use an ID table for quirks detection
firewire: ohci: reorder struct fw_ohci for better cache efficiency
firewire: ohci: remove unused dualbuffer IR code
firewire: core: combine a bit of repeated code
firewire: core: change type of a data buffer
firewire: cdev: increment ABI version number
firewire: cdev: add more flexible cycle timer ioctl
firewire: core: rename an internal function
firewire: core: fix an information leak
firewire: core: increase stack size of config ROM reader
firewire: core: don't fail device creation in case of too large config ROM blocks
firewire: core: fix "giving up on config rom" with Panasonic AG-DV2500
firewire: remove incomplete Bus_Time CSR support
firewire: get_cycle_timer optimization and cleanup
firewire: ohci: enable cycle timer fix on ALi and NEC controllers
firewire: ohci: work around cycle timer bugs on VIA controllers
firewire: make PCI device id constant
...
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (45 commits)
compal-laptop: Make it depend on CONFIG_RFKILL
classmate-laptop: Added some keys present in other devices
MAINTAINERS: Add git tree to x86 Platform Drivers
asus-acpi: remove duplicate comparison of asus_model strings
toshiba-acpi: fix multimedia keys on some machines
dell-laptop: Fix errors on failure and exit paths
dell-laptop: Fix build error by making buffer_mutex static
asus-laptop: fix style problems reported by checkpath.pl
asus-laptop: use device_create_file() instead of platform_group
asus-laptop: clean led code
asus-laptop: add gps rfkill
asus-laptop: set initial lcd state
asus-laptop: leds, remove dead code and fix asus_led_exit()/asus_led_init()
asus-laptop: add backlight changes notifications
asus-laptop: add bluetooth keys found on M9V
asus-laptop: switch to sparse keymap library
asus-laptop: rename wireless_status to wlan_status to avoid confusion
asus-laptop: add error check for write_acpi_int calls
asus-laptop: stop using ASUS_HANDLE and use relative methods instead
asus-laptop: rename function talking directly to acpi with asus_xxx scheme
...
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c: Document the message size limit
i2c-algo-pca: Drop duplicate variable
i2c: Hook up runtime PM support
i2c-parport-light: Add SMBus alert support
i2c-parport: Add SMBus alert support
i2c: Separate Kconfig option for i2c-smbus
i2c: Add SMBus alert support
i2c-parport: Give powered devices some time to settle
i2c-tiny-usb: Fix a comment on bus frequency
i2c-i801: Add Intel Cougar Point device IDs
i2c: Make PCI device ids constant
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (48 commits)
IB/srp: Clean up error path in srp_create_target_ib()
IB/srp: Split send and recieve CQs to reduce number of interrupts
RDMA/nes: Add support for KR device id 0x0110
IB/uverbs: Use anon_inodes instead of private infinibandeventfs
IB/core: Fix and clean up ib_ud_header_init()
RDMA/cxgb3: Mark RDMA device with CXIO_ERROR_FATAL when removing
RDMA/cxgb3: Don't allocate the SW queue for user mode CQs
RDMA/cxgb3: Increase the max CQ depth
RDMA/cxgb3: Doorbell overflow avoidance and recovery
IB/core: Pack struct ib_device a little tighter
IB/ucm: Clean whitespace errors
IB/ucm: Increase maximum devices supported
IB/ucm: Use stack variable 'base' in ib_ucm_add_one
IB/ucm: Use stack variable 'devnum' in ib_ucm_add_one
IB/umad: Clean whitespace
IB/umad: Increase maximum devices supported
IB/umad: Use stack variable 'base' in ib_umad_init_port
IB/umad: Use stack variable 'devnum' in ib_umad_init_port
IB/umad: Remove port_table[]
IB/umad: Convert *cdev to cdev in struct ib_umad_port
...
Fix docbook errors for x86 headers that were recently merged:
docproc: arch/x86/include/asm/atomic_32.h: No such file or directory
docproc: arch/x86/include/asm/io_32.h: No such file or directory
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Brian Gerst <brgerst@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] pSesInfo->sesSem is used as mutex. Rename it to session_mutex and
[CIFS] Use unsigned ea length for clarity
cifs: set server_eof in cifs_fattr_to_inode
[CIFS] Minor cleanup to EA patch
cifs: merge CIFSSMBQueryEA with CIFSSMBQAllEAs
cifs: verify lengths of QueryAllEAs reply
cifs: increase maximum buffer size in CIFSSMBQAllEAs
cifs: rename name_len to list_len in CIFSSMBQAllEAs
cifs: clean up indentation in CIFSSMBQAllEAs
cifs: add parens around smb_var in BCC macros
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (38 commits)
SELinux: Make selinux_kernel_create_files_as() shouldn't just always return 0
TOMOYO: Protect find_task_by_vpid() with RCU.
Security: add static to security_ops and default_security_ops variable
selinux: libsepol: remove dead code in check_avtab_hierarchy_callback()
TOMOYO: Remove __func__ from tomoyo_is_correct_path/domain
security: fix a couple of sparse warnings
TOMOYO: Remove unneeded parameter.
TOMOYO: Use shorter names.
TOMOYO: Use enum for index numbers.
TOMOYO: Add garbage collector.
TOMOYO: Add refcounter on domain structure.
TOMOYO: Merge headers.
TOMOYO: Add refcounter on string data.
TOMOYO: Reduce lines by using common path for addition and deletion.
selinux: fix memory leak in sel_make_bools
TOMOYO: Extract bitfield
syslog: clean up needless comment
syslog: use defined constants instead of raw numbers
syslog: distinguish between /proc/kmsg and syscalls
selinux: allow MLS->non-MLS and vice versa upon policy reload
...
Currently if the driver fails to register on port, the kernel
crashes with the following stack:
cpu 0x1: Vector: 300 (Data Access) at [c0000000e0303090]
pc: c00000000039aa74: .__mutex_lock_slowpath+0x44/0x10c
lr: c00000000039aa58: .__mutex_lock_slowpath+0x28/0x10c
[c0000000e03033c0] c00000000026b074 .uart_remove_one_port+0xbc/0x16c
[c0000000e0303460] d0000000000e0554 .jsm_remove_uart_port+0x8c/0x10c [jsm]
[c0000000e03034f0] d0000000000dc034 .jsm_remove_one+0x34/0x108 [jsm]
[c0000000e0303590] c0000000001f4aa0 .pci_device_remove+0x48/0x74
...
This patch just fixes the code flow to abort the load when an
error is detected.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If jsm fails to load, then remove the uart stuff, otherwise,
the things (as files), will be there forever (even when the module
is unloaded). If you try to reload the module, the following message
appears:
kobject_add_internal failed for ttyn1 with -EEXIST, don't try to
register things with the same name in the same directory.
This patch remove the uart things when the driver fails.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This new VT mode (VT_PROCESS_AUTO) does everything that VT_PROCESS does
except that it doesn't wait for a VT_RELDISP ioctl before switching
away from a VT with that mode.
If the X server eventually uses this new mode, debugging and crash
recovery should become easier. This is because even when currently in
the VT of a frozen X server it would still be possible to switch out
by doing SysRq-r and then CTRL-<number of a text vt>, sshing in and
doing chvt <number of a text vt>, or any other method of VT switching.
The general concensus on #xorg-devel seems to be that it should be
safe to use this with X now that we have KMS.
This also moves the VT_ACKACQ define to a more appropriate place,
for clarity's sake.
Signed-off-by: Ari Entlich <atrigent@ccs.neu.edu>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We allocate during interrupts so while our buffering is normally diced up
small anyway on some hardware at speed we can pressure the VM excessively
for page pairs. We don't really need big buffers to be linear so don't try
so hard.
In order to make this work well we will tidy up excess callers to request_room,
which cannot itself enforce this break up.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This was noticed by Matthias Urlichs and he proposed a fix. This patch
does the fixing a different way to avoid introducing several new race
conditions into the code.
The problem case is TTY_DRIVER_RESET_TERMIOS = 0. In that case while we
abort the ldisc change, the hangup processing has not cleaned up and restarted
the ldisc either.
We can't restart the ldisc stuff in the set_ldisc as we don't know what
the hangup did and may touch stuff we shouldn't as we are no longer
supposed to influence the tty at that point in case it has been re-opened
before we get rescheduled.
Instead do it the simple way. Always re-init the ldisc on the hangup, but
use TTY_DRIVER_RESET_TERMIOS to indicate that we should force N_TTY.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MFD_TIMBERDALE doesn't appear to be defined anywhere. However the code in
question can build happily without platform specifics so remove the check
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The original author didn't realise the kernel lock was a drop while sleep
lock so did clever (and wrong) things to work around the non need to avoid
deadlocks. Remove the cleverness and the comment (as we don't hold the BKL
now anyway in those paths)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The Nozomi tty handling is very broken on the open/close side (See
http://bugzilla.kernel.org/show_bug.cgi?id=13024 for one example). In
particular it marks the tty as closed on the first close() not on the last.
Most of the logic is pretty solid except for the open/close path so switch
to the tty_port helpers and let them do all the heavy lifting. This is also
fixes all the POSIX behaviour violations in the open/close paths.
Begin by adding the tty port usage
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Revised patch to use the new kfifo API. This replaces the one that was dropped
from -next due to collisions with the kfifo API changes.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bcm6358 CPU has two uarts, make it possible to use the second one.
Signed-off-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we always check for gdb breaks even when it isn't active, we get false
positives on normal code and the system panics.
URL: http://blackfin.uclinux.org/gf/tracker/5277
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we don't disable the DMA TX channel, an inopportune timeout will
trigger the interrupt handler and may cause a dead lock with the spin_lock.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
For UARTs that have dedicated hardware flow control support, there will be
no gpios to request/free as they are part of the normal peripheral pins.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found a potential null dereference in mgsl_put_char and
mgsl_write. There is a check for tty being NULL, but it is
dereferenced earlier.
Actually, tty cannot be NULL in .write and .put_char, so remove
the tests.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stephen Rothwell found the following warning (x86_64 allmodconfig):
drivers/char/ip2/ip2main.c:511: warning: 'ip2_setup' defined but not used
This patch adds module parameter to fix the above warning.
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
On the kernel command line we can pass "module parameters". So #ifdef
MODULE is obsolute now. Remove it completely. When CONFIG_PCI=n and
building ip2main.c then we are hit by the following warning. So move
*pdev into #ifdef CONFIG_PCI.
drivers/char/ip2/ip2main.c: In function `ip2_loadmain':
drivers/char/ip2/ip2main.c:542: warning: unused variable `pdev'
Signed-off-by: Rakib Mullick <rakib.mullick@gmail.com>
Acked-by: Michael H. Warfield <mhw@WittsEnd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We can pass "module parameters" on the kernel command line even when
!MODULE. So, #ifdef MODULE becomes obsolete. Also move the declaration
moxa_board_conf at the start of the function, since we were hit by the
following warning.
drivers/char/moxa.c: In function `moxa_init':
drivers/char/moxa.c:1040: warning: ISO C90 forbids mixed declarations and code
Signed-off-by: Rakib Mullick<rakib.mullick@gmail.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
vtermnos[] is unsigned, so this test was wrong.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
Convert printks to pr_<level>
Convert some embedded function names to %s...__func__
Remove a period after exclamation points.
Remove #define pr_dbg which could be used by future kernel.h includes
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jiri Slaby <jirislaby@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Stanse found unnecessary test in mxser_startup.
tty is dereferenced earlier, the test is superfluous. Remove it.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
With gcc 4.0.2:
drivers/char/cyclades.c: In function 'cyy_interrupt':
drivers/char/cyclades.c:581: warning: 'info' may be used uninitialized in this function
introduced by
: commit 3aeea5b922
: Author: Jiri Slaby <jirislaby@gmail.com>
: AuthorDate: Sat Sep 19 13:13:16 2009 -0700
: Commit: Live-CD User <linux@linux.site>
: CommitDate: Sat Sep 19 13:13:16 2009 -0700
:
: cyclades: introduce cyy_readb/writeb
In fact the true branch which uses uninitialized 'info' can never
happen because chip is always less than ->nchips and channel is
always less than 4 which we alloc.
So behave similar to rx handling and remove the test completely.
I wonder why gcc 4.4.1 doesn't spit a word.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jiri Slaby <jslaby@novell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The variables were unsigned so the tests did not work.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add different model (with a different PCI ID) to support Korenix JetCard.
Signed-off-by: Kiros Yeh <kiros@korenix.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The platform code doesn't have to provide platform data to get sensible
default behaviour from the imx serial driver.
This patch does not handle NULL dereference in the IrDA case, which still
requires a valid platform data pointer (in imx_startup()/imx_shutdown()),
since I don't know whether there is a sensible default behaviour, or
should the operation just fail cleanly.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Oskar Schirmer <os@emlix.com>
Cc: Fabian Godehardt <fg@emlix.com>
Cc: Daniel Glöckner <dg@emlix.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is heavily based on an earlier patch found on the linux-serial
mailing list [1], written by Darius Augulis.
The previous incarnation of this patch only supported a 2x serial port
card. I have added support for my SYBA 6x serial port card, and tested on
x86.
[1]: http://marc.info/?l=linux-serial&m=124975806304760
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Cc: Darius Augulis <augulis.darius@gmail.com>
Cc: Greg KH <greg@kroah.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix transmit bug that could drop send data if write() called close to
serial transmitter going idle after sending previous data. Bug is caused
by incorrect use of device information member tx_count.
Driver originally processed one data block (write call) at a time, waiting
for transmit idle before sending more. tx_count recorded how much data
was loaded in DMA buffers on write(), and was cleared on send completion.
tx_count use was overloaded to record accumulated data from put_char()
callback when transmitter was idle.
A bug was introduced when transmit code was reworked to allow multiple
blocks of data in the tx DMA buffers which keeps transmitter from going
idle between blocks. tx_count was set to size of last block loaded,
cleared when tx went idle, and monitored to know when to restart
transmitter without proper synchronization. tx_count could be cleared
when unsent data remained in DMA buffers and transmitter required
restarting, effectively dropping unsent data.
Solution:
1. tx_count now used only to track accumulated data from put_char
2. DMA buffer state tracked by direct inspection of descriptors
with spinlock synchronization
3. consolidate these tasks in tx_load() :
a. check for available buffer space
b. load buffers
c. restart DMA and or serial transmitter as needed
These steps were previously duplicated in multiple places,
sometimes incompletely.
4. fix use of tx_count as active transmit indicator,
instead using tx_active which is meant for that purpose
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Permits using KGDB over the console with the atmel_serial driver.
[akpm@linux-foundation.org: s/barrier/cpu_relax/]
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This macro is a duplicate of ARRAY_SIZE defined in kernel api, so just use
that instead.
Signed-off-by: Thiago Farina <tfransosi@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Augment the UPF_FIXED_TYPE logic, which currently applies to UART ports
provisioned using platform_device_register.
The suggested patch applies same logic into 'serial8250_register_ports',
making UART ports provisioned using early_serial_setup inherit their
properties from the uart_config entry.
Signed-off-by: Shmulik Ladkani <shmulik@jungo.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fit blackfin uart over sport driver into common uart inftrastructure. It
is based on the early platform interfaces to get the platform data early
when the console is initilized.
1. Enable sport uart driver to change uart baud, data bit, stop bit at
runtime. Bind the index of uart device nodes to physical index of
sports.
2. Move all platform data into arch specific board files. Register
and probe platform device data in both early and normal stages.
3. Console is registered in sport uart driver as well.
4. Remove 500 us block waiting in sport tx stop code by putting a
dummy data into tx fifo to make sure the sport tx stops when all bytes
are shifted out except for the dummy data.
5. clean up a bit and fix up coding style.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
