ata_irq_on() isn't used outside of libata core layer. The function is
TF/SFF interface specific but currently used by core path with some
hack too. Move it from include/linux/libata.h to
drivers/ata/libata-sff.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata waits for !BSY even when the status register reports 0xff.
This causes long boot delays when D8 isn't pulled down properly. This
patch does the followings.
* don't wait if status register is 0xff in all wait functions
* make ata_busy_sleep() return 0 on success and -errno on failure.
-ENODEV is returned on 0xff status and -EBUSY on other failures.
* make ata_bus_softreset() succeed on 0xff status. 0xff status is not
reset failure. It indicates no device. This removes unnecessary
retries on such ports. Note that the code change assumes unoccupied
port reporting 0xff status does not produce valid device signature.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Joe Jin <lkmaillist@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
needs a changelog
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for ADMA mode on NVIDIA nForce4 (CK804/MCP04) SATA
controllers to the sata_nv driver. Benefits of ADMA mode include:
- NCQ support
- Reduced CPU overhead (controller DMAs command information from memory
instead of them being pushed in by the CPU)
- Full 64-bit DMA support
ADMA mode is enabled by default in this version. To disable it, set the
module parameter adma_enabled=0.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
- use pci_iomap() [Alan, version 0.0.5t]
- fix Alan's version 0.0.5t change
- line length, trailing whitespace, case indentation cleanups
- don't use deprecated ->eng_timeout() in a driver that uses new EH
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a legacy mode PATA driver for the 6101/45 and will also drive
the SATA ports 1 & 2 in legacy mode as well if desired. Tested and
confirmed working by users. The chip supports AHCI type behaviour for
SATA and has a more advanced PATA interface as well so this driver will
get it working but not get best performance for now.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_module_init() conversion for pata_pdc2027x
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Alan Cox <alan@redhat.com> but please apply as follows to keep
revision id straight
Cc: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_module_init convertion in ata_generic.c.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Winbond 83759A support in non-multichip mode (afaik nobody ever used
multichip mode anyway). The 83759 is not supported by this driver as it
is already handled elsewhere and doens't use the same interfaces.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (31 commits)
[MIPS] Remove duplicate ISA DMA code for 0 DMA channel case.
[MIPS] Remove unused definition of cpu_to_lelongp()
[MIPS] Remove userspace proofing from <asm/bitops.h>.
[MIPS] Remove old junk left from old atomic_lock.
[MIPS] Use conditional traps for BUG_ON on MIPS II and better.
[MIPS] mips HPT cleanup: make clocksource_mips public
[MIPS] do_IRQ cleanup
[MIPS] Avoid dupliate D-cache flush on R400C / R4400 SC and MC variants.
[MIPS] Remove redundant r4k_blast_icache() calls
[MIPS] Work around bogus gcc warnings.
[MIPS] Fix double inclusions
[MIPS] use generic_handle_irq, handle_level_irq, handle_percpu_irq
[MIPS] IRQ cleanups
[MIPS] mips hpt cleanup: get rid of mips_hpt_init
[MIPS] PB1200: Remove duplicate definitions
[MIPS] Fix alignment hole in struct cache_desc; shrink struct.
[MIPS] Oprofile: kernel support for the R10000.
[MIPS] Remove unused R10000 performance counter definitions.
[MIPS] Add support for kexec
[MIPS] Don't print presence of WAIT instruction on bootup.
...
* 'for-2.6.20' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/selinux-2.6:
SELinux: validate kernel object classes and permissions
SELinux: ensure keys constant in hashtab_search
SELinux: export object class and permission definitions
SELinux: remove current object class and permission validation mechanism
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/usb-2.6: (103 commits)
usbcore: remove unused argument in autosuspend
USB: keep count of unsuspended children
USB hub: simplify remote-wakeup handling
USB: struct usb_device: change flag to bitflag
OHCI: make autostop conditional on CONFIG_PM
USB: Add autosuspend support to the hub driver
EHCI: Fix root-hub and port suspend/resume problems
USB: create a new thread for every USB device found during the probe sequence
USB: add driver for the USB debug devices
USB: added dynamic major number for USB endpoints
USB: pegasus error path not resetting task's state
USB: endianness fix for asix.c
USB: build the appledisplay driver
USB serial: replace kmalloc+memset with kzalloc
USB: hid-core: canonical defines for Apple USB device IDs
USB: idmouse cleanup
USB: make drivers/usb/core/driver.c:usb_device_match() static
USB: lh7a40x_udc remove double declaration
USB: pxa2xx_udc recognizes ixp425 rev b0 chip
usbtouchscreen: add support for DMC TSC-10/25 devices
...
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/driver-2.6: (36 commits)
Driver core: show drivers in /sys/module/
Documentation/driver-model/platform.txt update/rewrite
Driver core: platform_driver_probe(), can save codespace
driver core: Use klist_remove() in device_move()
driver core: Introduce device_move(): move a device to a new parent.
Driver core: make drivers/base/core.c:setup_parent() static
driver core: Introduce device_find_child().
sysfs: sysfs_write_file() writes zero terminated data
cpu topology: consider sysfs_create_group return value
Driver core: Call platform_notify_remove later
ACPI: Change ACPI to use dev_archdata instead of firmware_data
Driver core: add dev_archdata to struct device
Driver core: convert sound core to use struct device
Driver core: change mem class_devices to be real devices
Driver core: convert fb code to use struct device
Driver core: convert firmware code to use struct device
Driver core: convert mmc code to use struct device
Driver core: convert ppdev code to use struct device
Driver core: convert PPP code to use struct device
Driver core: convert cpuid code to use struct device
...
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix timezone handling on stat to os/2
[CIFS] Incorrect hardlink count when original file is cached (oplocked)
Show the drivers, which belong to the module:
$ ls -l /sys/module/usbcore/drivers/
hub -> ../../../bus/usb/drivers/hub
usb -> ../../../bus/usb/drivers/usb
usbfs -> ../../../bus/usb/drivers/usbfs
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is almost a rewrite of the driver-model/platform.txt documentation;
the previous text was obsolete (for several years), evidently it never
got updated to match the change from being a PC "legacy_bus" to the more
widely used core bus for most embedded systems.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This defines a new platform_driver_probe() method allowing the driver's
probe() method, and its support code+data, to safely live in __init
sections for typical system configurations.
Many system-on-chip processors could benefit from this API, to the tune
of recovering hundreds to thousands of bytes per driver. That's memory
which is currently wasted holding code which can never be called after
system startup, yet can not be removed. It can't be removed because of
the linkage requirement that pointers to init section code (like, ideally,
probe support) must not live in other sections (like driver method tables)
after those pointers would be invalid.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As pointed out by Alan Stern, device_move needs to use klist_remove which waits
until removal is complete.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Provide a function device_move() to move a device to a new parent device. Add
auxilliary functions kobject_move() and sysfs_move_dir().
kobject_move() generates a new uevent of type KOBJ_MOVE, containing the
previous path (DEVPATH_OLD) in addition to the usual values. For this, a new
interface kobject_uevent_env() is created that allows to add further
environmental data to the uevent at the kobject layer.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Acked-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global setup_parent() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
since most of the files in sysfs are text files,
it would be nice, if the "store" function called
during sysfs_write_file() gets a zero terminated
string / data.
The current implementation seems not to ensure this.
(But only if it is the first time the zeroed buffer
page is allocated.)
So the buffer can be scanned by sscanf() easily,
for example.
This patch simply sets a \0 char behind the
data in buffer->page.
Signed-off-by: Thomas Maier <balagi@justmail.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Take return value of sysfs_create_group() into account. That function got
called in case of CPU_ONLINE notification. Since callbacks are not allowed
to fail on CPU_ONLINE notification do the sysfs group creation on
CPU_UP_PREPARE notification.
Also remember if creation succeeded in a bitmask. So it's possible to know
whether it's legal to call sysfs_remove_group or not.
In addition some other minor stuff:
- since CPU_UP_PREPARE might fail add CPU_UP_CANCELED handling as well.
- use hotcpu_notifier instead of register_hotcpu_notifier.
- #ifdef code that isn't needed in the !CONFIG_HOTPLUG_CPU case.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the call to platform_notify_remove() to after the call to
bus_remove_device(), where it belongs. It's bogus to notify the platform
of removal while drivers are still attached to the device and possibly
still operating since the platform might use this callback to tear down
some resources used by the driver (ACPI bits, iommu table, ...)
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change ACPI to use dev_archdata instead of firmware_data
This patch changes ACPI to use the new dev_archdata on i386, x86_64
and ia64 (is there any other arch using ACPI ?) to store it's
acpi_handle.
It also removes the firmware_data field from struct device as this
was the only user.
Only build-tested on x86
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add arch specific dev_archdata to struct device
Adds an arch specific struct dev_arch to struct device. This enables
architecture to add specific fields to every device in the system, like
DMA operation pointers, NUMA node ID, firmware specific data, etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andi Kleen <ak@suse.de>
Acked-By: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
It also makes the struct sound_card to show up as a "real" device
where all the different sound class devices are placed as childs
and different card attribute files can hang off of. /sys/class/sound is
still a flat directory, but the symlink targets of all devices belonging
to the same card, point the the /sys/devices tree below the new card
device object.
Thanks to Kay for the updates to this patch.
Signed-off-by: Kay Sievers <kay.sievers@novell.com>
Acked-by: Jaroslav Kysela <perex@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Also fixes up the isdn drivers that were putting something in the class
device's directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This also ment that some of the misc drivers had to also be fixed
up as they were assuming the device was a class_device.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Converts from using struct "class_device" to "struct device" making
everything show up properly in /sys/devices/ with symlinks from the
/sys/class directory.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Turn off class symlinks CONFIG_SYSFS_DEPRECATED is enabled.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
