The calculations done with sync_clk are anyway in picoseconds
and switching to picoseconds allows sync_clk values that are
not a whole number of nanoseconds - which is sometimes the
case.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If the TPA6130 is compiled as module the id and power_gpio values are
arbitrary at module probing time since the rx51_tpa6130a2_data was marked as
__initdata. Fix this by using __initdata_or_module. Then __initdata is
defined only if the kernel is built without CONFIG_MODULES and omitted
otherwise.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit ed919b0 "mmc: sdio: fix runtime PM anomalies by introducing
MMC_CAP_POWER_OFF_CARD" it is required to specify MMC_CAP_POWER_OFF_CARD
to have runtime PM support. As the wl1251 driver expects card to be
powered down when it's not used, wifi will no longer work after interface
is brought down at least once without functioning runtime PM.
Fix this by declaring MMC_CAP_POWER_OFF_CARD for MMC3.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_reserve functionality to board-omap4panda.c.
Helps in the reserving boot time memory in SDRAM, used here for
framebuffer allocation.
This patch is in similar lines to commit id 71ee7dad9b, from
Russell king
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tony@atomide.com: fixed to be before .map_io as pointed out by Russell King]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register BH1780GLI Ambient light sensor, which is an I2C device
for 4430SDP board.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure the LED is turned off at boot time, and configure the GPIO LED
device as active low.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpio_direction_output() has a value argument, there's no need to call
gpio_set_value() explicitly right after.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 72f381ba05 (omap3: Remove VMMC2 regulator on IGEP v2)
removed an unused regulator entry, but left the second MMC channel
(used by the Libertas WLAN module) without link to power regulator.
This causes the SDIO module to fail being detected.
This patch adds the two regulators that actually feed the WLAN module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected. Details of the power supply
implementation were kindly provided by Enric Balletbo i Serra.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Tested on an IGEPv2 Rev-B.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch "OMAP2xxx: hwmod: add I2C hwmods for OMAP2420, 2430"
in linux-next as of 20101203 introduced the following build
warning - fix this by removing the stray i2c_dev_attr.
arch/arm/mach-omap2/omap_hwmod_2430_data.c:483: warning: 'i2c_dev_attr' defined but not used
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To support tvout on rx51,added Intilization data,
tvout as display device and enabled venc through gpio
on rx51
Signed-off-by: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming ASoC core and tlv320aic3x changes makes possible to take b part of
TLV320AIC34 into use on RX51/N900. Prepare to this by adding virtual supplies
and platform data for b part of the codec.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove second tlv320aic3x.h inclusion that came along the commit f0fba2a
"ASoC: multi-component - ASoC Multi-Component Support".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no MFD config option, MFD_SUPPORT should be selected instead.
This will prevent build errors when trying out different configurations.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clk_get() return value should be checked with IS_ERR(). Furthermore,
clocks should be put and disabled properly.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DMA library into DMA platform driver and make use of
platform data provided by hwmod data base for OMAP2+ onwards.
For OMAP1 processors, the DMA driver in mach-omap uses resource
structures for getting platform data.
Thanks to Tony Lindgren <tony@atomide.com> for fixing various
omap1 issues and testing the same on OSK5912 board.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare OMAP2+ DMA to use hwmod infrastructure so that DMA can register
as platform device.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP4 DMA hwmod data. In addition to original dma hwmod data,
the following changes are added.
1. DMA device attributes structure is introduced for diffenrenciating
OMAP cpu's based on DMA features.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2430 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2420 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
platform_cpu_die() is entered from the CPU's own idle thread, which
can not be migrated to other CPUs. Moreover, the 'cpu' argument
comes from the thread info, which will always be the 'current'
CPU. So remove this useless bug check.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We always need to wait for the dying CPU to reach a safe state before
taking it down, irrespective of the requirements of the platform.
Move the completion code into the ARM SMP hotplug code rather than
having each platform re-implement this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All platforms call trace_hardirqs_off() in their secondary startup code,
so move this into the core SMP code - it doesn't need to be in the
per-platform code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There is a certain amount of smp_prepare_cpus() which doesn't belong
in the platform support code - that is, code which is invariant to the
SMP implementation. Move this code into arch/arm/kernel/smp.c, and
add a platform_ prefix to the original function.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
scu_get_core_count() never returns zero cores, so we don't need to
check and correct if ncores is zero.
Tegra was missing the check against NR_CPUS, leading to a potential
bitfield overflow if this becomes the case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that the number of CPUs is sanity checked before setting
the number of possible CPUs. This avoids any chance of overflowing
the cpu_possible bitmap.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AXI protocol specifies that the write response can only
be sent back to an AXI master when the last write data has been
accepted. This optimization enables the PL310 to send the write
response of certain write transactions as soon as the store buffer
accepts the write address. This behavior is not compatible with
the AXI protocol and is disabled by default. You enable this
optimization by setting the Early BRESP Enable bit in the
Auxiliary Control Register (bit [30]).
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clearing bit 22 in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling L2 prefetching improves performance as shown on Panda
ES2.1 board with mem test, and it has measurable impact on
performances. I think we should consider it, even though it damages
"writes" a bit. (rebased to k.org)
Usually the prefetch is used at both levels together L1 + L2, however,
to enable the CP15 prefetch engines, these are under security, and on
GP devices, we cannot enable it(e.g. on PandaBoard). However, just
enabling PL310 prefetch seems to provide performance improvement,
as shown in the data below (from Ubuntu) and would be a great thing
to pull in.
What prefetch does is enable automatic next line prefetching. With this
enabled, whenever the PL310 receives a cachable read request, it
automatically prefetches the following cache line as well.
Measurement Data:
==
STOCK 10.10 WITHOUT PATCH
========================
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2aaad000 0x2b2ad000
copy libc 133 MB/s
copy Android v5 273 MB/s
copy Android NEON 235 MB/s
copy INT32 116 MB/s
copy ASM ARM 187 MB/s
copy ASM VLDM 64 204 MB/s
copy ASM VLDM 128 173 MB/s
copy ASM VLD1 216 MB/s
read ASM ARM 286 MB/s
read ASM VLDM 242 MB/s
read ASM VLD1 286 MB/s
write libc 1947 MB/s
write ASM ARM 1943 MB/s
write ASM VSTM 1942 MB/s
write ASM VST1 1935 MB/s
10.10 + PATCH
=============
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2ab17000 0x2b317000
copy libc 129 MB/s
copy Android v5 256 MB/s
copy Android NEON 356 MB/s
copy INT32 127 MB/s
copy ASM ARM 321 MB/s
copy ASM VLDM 64 337 MB/s
copy ASM VLDM 128 321 MB/s
copy ASM VLD1 350 MB/s
read ASM ARM 496 MB/s
read ASM VLDM 470 MB/s
read ASM VLD1 488 MB/s
write libc 1701 MB/s
write ASM ARM 1682 MB/s
write ASM VSTM 1693 MB/s
write ASM VST1 1681 MB/s
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes the hardcoded value of auxctrl value and
construct it using bitfields
Bit 25 is reserved and is always set to 1. Same value
of this bit is retained in this patch
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
New assemblers need -march=armv7-a+sec on command line or
.arch_extension sec inline to enable use of the smc instruction.
This patch uses as-instr to check the latter to conditionally
enable the former in AFLAGS for files that use smc.
Checked on both old and new binutils to verify that it does
not break old versions.
Signed-off-by: John Rigby <john.rigby@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch will kill following section mismatch warnings:
WARNING: vmlinux.o(.text+0x24a00): Section mismatch in reference from the function zoom_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function zoom_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because zoom_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.text+0x24bfc): Section mismatch in reference from the function cm_t35_twl_gpio_setup() to the (unknown reference) .init.data:(unknown)
The function cm_t35_twl_gpio_setup() references
the (unknown reference) __initdata (unknown).
This is often because cm_t35_twl_gpio_setup lacks a __initdata
annotation or the annotation of (unknown) is wrong.
WARNING: vmlinux.o(.data+0x1d3e0): Section mismatch in reference from the variable h4_config to the (unknown reference) .init.data:(unknown)
The variable h4_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1dc08): Section mismatch in reference from the variable sdp2430_config to the (unknown reference) .init.data:(unknown)
The variable sdp2430_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
WARNING: vmlinux.o(.data+0x1e1d8): Section mismatch in reference from the variable apollon_config to the (unknown reference) .init.data:(unknown)
The variable apollon_config references
the (unknown reference) __initdata (unknown)
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console,
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Power to the wl12xx wlan device is controlled by a fixed regulator.
Boards that have the wl12xx should select REGULATOR_FIXED_VOLTAGE so
users will not be baffled.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add comments and IDs for the following erratas:
- i540: MPU cannot exit from Standby,
- i478: Unexpected Cold-Reset is generated when device is coming
back from OFF mode
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add minimal support for Nokia RM-680 board.
Tested with omap2plus_defconfig.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated to remove omap_gpio_init
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce 97.6/195.2 MHz memory timing data. Based on patches by Eduardo
Valentin, Igor Dmitriev and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Cc: Igor Dmitriev <ext-dmitriev.igor@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Actually check for errors: print an error log and return NULL.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use an array to make it easier to add new values.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename the current timings to indicate they're for 166 MHz. Based on
patches by Eduardo Valentin and Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add a header file for Nokia SDRAM functions. Based on patches by Juha
Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Rename the file and functions so that it can be reused by future Nokia
boards. Based on patches by Juha Keski-Saari.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* usb-next: (132 commits)
USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
USB: uas: Ensure we only bind to a UAS interface
USB: uas: Rename sense pipe and sense urb to status pipe and status urb
USB: uas: Use kzalloc instead of kmalloc
USB: uas: Fix up the Sense IU
usb: musb: core: kill unneeded #include's
DA8xx: assign name to MUSB IRQ resource
usb: gadget: g_ncm added
usb: gadget: f_ncm.c added
usb: gadget: u_ether: prepare for NCM
usb: pch_udc: Fix setup transfers with data out
usb: pch_udc: Fix compile error, warnings and checkpatch warnings
usb: add ab8500 usb transceiver driver
USB: gadget: Implement runtime PM for MSM bus glue driver
USB: gadget: Implement runtime PM for ci13xxx gadget
USB: gadget: Add USB controller driver for MSM SoC
USB: gadget: Introduce ci13xxx_udc_driver struct
USB: gadget: Initialize ci13xxx gadget device's coherent DMA mask
USB: gadget: Fix "scheduling while atomic" bugs in ci13xxx_udc
USB: gadget: Separate out PCI bus code from ci13xxx_udc
...
It seems dsp-link will do this, and tidspbridge too at some point, but
right now it's not possible to select CONFIG_MPU_BRIDGE_IOMMU.
Cc: Fernando Guzman Lugo <fernando.lugo@ti.com>
Cc: Yogesh Marathe <yogesh_marathe@ti.com>
Signed-off-by: Felipe Contreras <felipe.contreras@nokia.com>
Some IOMMUs cannot use the whole 0x0 - 0xFFFFFFFF range.
With this new API the valid range can be set.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
We need to test for 24xx not 242x. Otherwise interrupts won't work.
Reported-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Provide a standard get_irqnr_preamble assembler macro for platforms
to use, which retrieves the base address of the GIC CPU interface
from gic_cpu_base_addr. Allow platforms to override this by defining
HAVE_GET_IRQNR_PREAMBLE.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Every architecture using the GIC has a gic_cpu_base_addr pointer for
GIC 0 for their entry assembly code to use to decode the cause of the
current interrupt. Move this into the common GIC code.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need to re-pass the base address for the CPU interfaces to the
GIC for secondary CPUs, as it will never be different from the boot CPU
- and even if it was, we'd overwrite the boot CPU's base address.
Get rid of this argument, and rename to gic_secondary_init().
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Provide gic_init() which initializes the GIC distributor and current
CPU's GIC interface for the boot (or single) CPU.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After Charu's GPIO hwmod patches, GPIO initialization on N800 emits
the following messages for all GPIO banks:
omap_hwmod: gpio1: cannot be enabled (3)
This is due to OMAP24XX_ST_GPIOS_SHIFT being defined as a bitmask.
Fix this and also fix two other macros that had the same problem.
Thanks to Tony Lindgren <tony@atomide.com> for originally reporting
this bug.
Signed-off-by: Paul Walmsley <paul@pwsan.com
Cc: Charulatha Varadarajan <charu@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise multi-omap1 support for omap1 won't work as the cpu_class_is_omap1()
won't work until the SoC is detected.
Note that eventually these will go away, please use ioremap + read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling the musb OTG mode for SDP and PANDA boards.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Registering the twl6030-usb transceiver device as a child to twl6030 core.
Removed the NOP transceiver init call from board file.
Populated twl4030_usb_data platform data structure with the function
pointers for OMAP4430 internal PHY operation to be used by twl630-usb driver.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Selecting the twl6030-usb for OMAP4430SDP and OMAP4PANDA boards and
adding OMAP4 internal phy code for compilation
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Adding the twl6030-usb transceiver support for OMAP4 musb driver.
OMAP4 supports 2 types of transceiver interface.
1. UTMI: The PHY is embedded within OMAP4. The transceiver functionality
is split between the twl6030 PMIC chip and OMAP4430. The VBUS, ID pin
sensing and OTG SRP generation part is integrated in TWL6030 and UTMI PHY
functionality is embedded within the OMAP4430.
There is no direct interactions between the MUSB controller and TWL6030
chip to communicate the session-valid, session-end and ID-GND events.
It has to be done through a software by setting/resetting bits in
one of the control module register of OMAP4430 which in turn toggles
the appropriate signals to MUSB controller.
The internal transceiver has functional clocks and
powerdown bits to powerdown the PHY for power saving.
Since there is no option available for having 2 transceiver drivers
for one USB controller, internal PHY specific APIs are passed through
plaform_data function pointers to use in the twl6030-usb transceiver
driver.
2. ULPI interface is provided for off-chip transceivers.
Signed-off-by: Hema HK <hemahk@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 4814ced511 (OMAP:
control: move plat-omap/control.h to mach-omap2/control.h)
moved <plat/control.h> to another location, preventing
drivers from accessing it, so we need to pass function
pointers from arch code to be able to talk to internal
PHY on AM35x.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
musb core doesn't need to know about platform
specific details. So start moving clock
handling to platform glue layer and make
musb core agnostic about that.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Just adding its own platform_driver, not really
using it yet.
When all HW glue layers are converted, more patches
will come to split power management code from musb_core
and move it completely to HW glue layer.
Signed-off-by: Felipe Balbi <balbi@ti.com>
change all ocurrences of musb_hdrc to musb-hdrc.
We will call glue layer drivers musb-<glue layer>,
so in order to keep things somewhat standard, let's
change the underscore into a dash.
Signed-off-by: Felipe Balbi <balbi@ti.com>
This will make things simpler when choosing which
glue layer to compile. It avoids a lot of magic
around the "default" Kconfig option and lets the
user choose what exactly s/he wants to compile.
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit 0d8e2d0dad (OMAP2+: PM/serial:
hold console semaphore while OMAP UARTs are disabled) added use of the
console semaphore to protect UARTs from being accessed after disabled
during idle, but this causes problems in suspend.
During suspend, the console semaphore is acquired by the console
suspend method (console_suspend()) so the try_acquire_console_sem()
will always fail and suspend will be aborted.
To fix, introduce a check so the console semaphore is only attempted
during idle, and not during suspend. Also use the same check so that
the console semaphore is not prematurely released during resume.
Thanks to Paul Walmsley for suggesting adding the same check during
resume.
Cc: Paul Walmsley <paul@pwsan.com>
Tested-by: Jean Pihet <j-pihet@ti.com>
Tested-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clk_get() return value should be checked with IS_ERR().
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Implement GPIO as a platform device.
GPIO APIs are used in machine_init functions. Hence it is
required to complete GPIO probe before board_init. Therefore
GPIO device register and driver register are implemented as
postcore_initcalls.
omap_gpio_init() does nothing now and this function would be
removed in the next patch as it's usage is spread across most
of the board files.
Inorder to convert GPIO as platform device, modifications are
required in clockxxxx_data.c file for OMAP1 so that device names
can be used to obtain clock instead of getting clocks by
name/NULL ptr.
Use runtime pm APIs (pm_runtime_put*/pm_runtime_get*) for enabling
or disabling the clocks, modify sysconfig settings and remove usage
of clock FW APIs.
Note 1: Converting GPIO driver to use runtime PM APIs is not done as a
separate patch because GPIO clock names are different for various OMAPs
and are different for some of the banks in the same CPU. This would need
usage of cpu_is checks and bank id checks while using clock FW APIs in
the gpio driver. Hence while making GPIO a platform driver framework,
PM runtime APIs are used directly.
Note 2: While implementing GPIO as a platform device, pm runtime APIs
are used as mentioned above and modification is not done in gpio's
prepare for idle/ resume after idle functions. This would be done
in the next patch series and GPIO driver would be made to use dev_pm_ops
instead of sysdev_class in that series only.
Due to the above, the GPIO driver implicitly relies on
CM_AUTOIDLE = 1 on its iclk for power management to work, since the
driver never disables its iclk.
This would be taken care in the next patch series (see Note 3 below).
Refer to
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg39112.html
for more details.
Note 3: only pm_runtime_get_sync is called in gpio's probe() and
pm_runtime_put* is never called. This is to make the implementation
similar to the existing GPIO code. Another patch series would be sent
to correct this.
In OMAP3 and OMAP4 gpio's debounce clocks are optional clocks. They
are enabled/ disabled whenever required using clock framework APIs
TODO:
1. Cleanup the GPIO driver. Use function pointers and register
offest pointers instead of using hardcoded values
2. Remove all cpu_is_ checks and OMAP specific macros
3. Remove usage of gpio_bank array so that only
instance specific information is used in driver code
4. Rename 'method'/ avoid it's usage
5. Fix the non-wakeup gpios handling for OMAP2430, OMAP3 & OMAP4
6. Modify gpio's prepare for idle/ resume after idle functions
to use runtime pm implentation.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated for bank specific revision and updated boards]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap_device_build() API to do platform_device_register of
GPIO devices. For OMAP2+ chips, the device specific data defined
in the centralized hwmod database will be used.
gpio_init needs to be done before machine_init functions access
gpio APIs. Hence gpio_init is made as a postcore_initcall.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Reviewed-by: Basak, Partha <p-basak2@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP4
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP3
Also remove "omap34xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP2430
Also remove "omap24xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add GPIO hwmod data for OMAP2420 and add the required
GPIO device attributes in the gpio header file
Also remove "omap24xx.h" header file as it is not required
anymore.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like some boards are calling gpio_request from init_irq.
This will make the request_irq fail, as GPIO will be initialized
as postcore_initcall.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Common GIC entry macro for omap
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch complements ed919b0 "mmc: sdio: fix runtime PM anomalies by
introducing MMC_CAP_POWER_OFF_CARD" by declaring MMC_CAP_POWER_OFF_CARD
on the ZOOM's wl1271 mmc slot.
This is required in order not to break runtime PM support for the wl1271
sdio driver.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This allows us to use smp_cross_call() to trigger a number of different
software generated interrupts, rather than combining them all on one
SGI. Recover the SGI number via do_IPI.
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Wakeup-on-timer code does not have/need debugfs dependency. Move
the function out of debugfs ifdef.
Fixes compile error when CONFIG_DEBUG_FS is disabled but PM debug is
enabled.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When OneNAND support is disabled, the platform code defines NULL
board_onenand_data and empty init function for us. By utilizing this we
can avoid cluttering board files with dummy definitions/wrappers.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If CONFIG_OMAP_MUX is not enabled, we can define board_mux in the header
file instead of forcing every single board to define it.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
[tony@atomide.com: updated for combined board-zoom files]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix the mailbox detection for OMAP3630 and 2430, also minor
cleanup on conditional ifdef's that could affect it.
Given that 2430 has an iva too, include it, as the same steps
for omap3 apply.
Signed-off-by: Omar Ramirez Luna <omar.ramirez@ti.com>
Acked-by: Hiroshi Doyu <hiroshi.doyu@nokia.com>
Soon resource data will get automatically
populated from a set of autogenerated data
from TI's hardware database for the OMAP
platform.
Such database, might not have resources at
the expected order by the current drivers.
While we could hack in some exceptions to
that tool to generate resources in a specific
order, it seems less fragile to use the
resource name instead. That way, no matter
what order the resources are generated, the
driver still work.
Modified the OMAP, Blackfin and Davinci
architecture files to add the name of the IRQs
in the resource structures and musb driver to
use the platform_get_irq_byname() api to get
the device and dma irq numbers instead of using
the index.
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Hema HK <hemahk@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Access to some registers depends on register access mode
Three different modes are available for OMAP (at least)
• Operational mode LCR_REG[7] = 0x0
• Configuration mode A LCR_REG[7] = 0x1 and LCR_REG[7:0]! = 0xBF
• Configuration mode B LCR_REG[7] = 0x1 and LCR_REG[7:0] = 0xBF
Define access modes and remove redefinitions and magic numbers
in serial drivers (and later in bluetooth driver).
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define MDR1 register serial definitions used in serial and
bluetooth drivers.
Change magic number to ones defined in serial_reg for omap1/2
serial driver.
Remove redefined MDR1 register definitions in omap-serial driver.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@nokia.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Craneboard is a hardware development platform based on the
Sitara AM3517 ARM Cortex - A8 microprocessor device. This is a
low cost reference design.
This patch adds basic board file. Detailed support will follow in
subsequent patches.
[1] http://www.ti.com/arm
[2] http://www.mistralsolutions.com/products/craneboard.php
Signed-off-by: Srinath <srinath@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It's easier to understand what that number means and
also avoids problems if we ever have to change it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
They are extremely similar anyway, let's get rid
of one file.
While at that, also remove the empty zoom_config
variable.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The changes are:
- Use 'for' loop instead 'while' loop.
- No need to initialize ret to 0, we're assigning it right after.
- No need to check for onenandcs < GPMC_CS_NUM here, it will always be true.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap_board_config_size is implicitly initialized to 0 in
plat-omap/common.c, get_config() won't dereference omap_board_config,
so we can remove the empty igep2_config array.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP4 SDP has an SMSC3320 PHY hooked up to EHCI on Port1.
The PHY power is controlled by GPIO 157.
Turn on the PHY power, and register the controller at init.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The OMAP4 has an on-chip EHCI controller. Select USB_ARCH_HAS_EHCI
to allow the EHCI driver to be built on OMAP4.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
- Add platform init code for EHCI on OMAP4
- Add pad configuration for PHY and TLL modes
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Add clkdev aliases for the USBHOST and USBTLL clocks on OMAP3 and
OMAP4, so that the driver can refer to the clocks using a common alias.
This will disappear when the driver is converted to use the hwmod
database, but until then this patch is needed.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Tony Lindgren <tony@atomide.com>
factorise some generic infrastructure to assist looking up struct clks
for the ARM & SH architecture.
as the code is identical at 99%
put the arch specific code for allocation as example in asm/clkdev.h
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The console semaphore must be held while the OMAP UART devices are
disabled, lest a console write cause an ARM abort (and a kernel crash)
when the underlying console device is inaccessible. These crashes
only occur when the console is on one of the OMAP internal serial
ports.
While this problem has been latent in the PM idle loop for some time,
the crash was not triggerable with an unmodified kernel until commit
6f251e9db1 ("OMAP: UART: omap_device
conversions, remove implicit 8520 assumptions"). After this patch, a
console write often occurs after the console UART has been disabled in
the idle loop, crashing the system. Several users have encountered
this bug:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg38396.htmlhttp://www.mail-archive.com/linux-omap@vger.kernel.org/msg36602.html
The same commit also introduced new code that disabled the UARTs
during init, in omap_serial_init_port(). The kernel will also crash
in this code when earlyconsole and extra debugging is enabled:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg36411.html
The minimal fix for the -rc series is to hold the console semaphore
while the OMAP UARTs are disabled. This is a somewhat overbroad fix,
since the console may not be located on an OMAP UART, as is the case
with the GPMC UART on Zoom3. While it is technically possible to
determine which devices the console or earlyconsole is actually
running on, it is not a trivial problem to solve, and the code to do
so is not really appropriate for the -rc series.
The right long-term fix is to ensure that no code outside of the OMAP
serial driver can disable an OMAP UART. As I understand it, code to
implement this is under development by TI.
This patch is a collaboration between Paul Walmsley <paul@pwsan.com>
and Tony Lindgren <tony@atomide.com>. Thanks to Ming Lei
<tom.leiming@gmail.com> and Pramod <pramod.gurav@ti.com> for their
feedback on earlier versions of this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Pramod <pramod.gurav@ti.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Jean Pihet <jean.pihet@newoldbits.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Add additional check to omap_uart_resume_idle() so that only
enabled (specifically, idle-enabled) UARTs are allowed to resume.
This matches the existing check in prepare idle.
Without this patch, the system will hang if a board is
configured to register only some uarts instead of all of
them and PM is enabled.
Cc: Govindraj R. <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 7c63984b86 (ARM: do not define VMALLOC_END relative to PAGE_OFFSET)
changed VMALLOC_END to be an explicit value. Before this, it was
relative to PAGE_OFFSET and therefore converted to unsigned long
as PAGE_OFFSET is an unsigned long. This introduced the following
build warning. Fix this by changing the explicit defines of
VMALLOC_END to be unsigned long.
CC arch/arm/mm/init.o
arch/arm/mm/init.c: In function 'mem_init':
arch/arm/mm/init.c:606: warning: format '%08lx' expects type 'long unsigned int', but argument 12 has type 'unsigned int'
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Uwe Kleine-K <u.kleine-koenig@pengutronix.dee>
Acked-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Removed mux: and added the __func__ macro to make debugging
easier.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
The mux framework allows the change of pad configuration by drivers
when needed. Prior to this the mux framework has to be initialised
with all the mux parameters specific to the board. The mux init is
already present in the board file for SDP. Adding the mux init
for panda boards.
Signed-off-by: sricharan <r.sricharan@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Select the CBS package if SDP4430 is enabled during config.
Use the proper package (CBL or CBS) based on chip revision.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Please note that the full muxmodes are re-defined for ES2 instead
of using the subset. There are 81 differences among 204 pins.
The subset fixup will have to iterate over the whole list for each
subset entry, which can lead to an important number of iteration.
On the other hand, it will take much more memory at boot time.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Select the CBL package if SDP4430 is enabled during config.
Initialize the mux framework during the board init.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add data for OMAP4430 generated from HW pinout & register database.
The data set is split in two partitions for both core and wkup.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Starting on OMAP4, the pin mux configuration is located in two
different partitions of the control module (CODE_PAD and WKUP_PAD).
The first one is inside the core power domain whereas the second
one is inside the wakeup.
- Add the capability to add any number of partition during board init
time depending of Soc partitioning.
- Add some init flags as well in order to avoid explicit Soc version
check inside the mux core code.
- Add a comment with mux0 mode on top of omap_mux/board/<partition>
if the current mux mode is not the default one.
Thanks to Tony Lindgren <tony@atomide.com> for the following improvements:
- Add omap_mux_get for getting the partition data so platform level
device code can use it.
- Fix the rx51 board code to use the new API.
- Do not store the partition for each mux entry. Look up the partition
for debugfs instead.
Thanks to Dan Murphy <dmurphy@ti.com> for testing on OMAP4 and reporting
a couple of bugs.
Thanks to Anand Gadiyar <gadiyar@ti.com> for testing on OMAP3 zoom and
bug report.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Murphy Dan <dmurphy@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Replace all the printk(KERN_XXX... with pr_xxx macros.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
While at it, fix two checkpatch errors.
Several non-const struct instances constified by this patch were added after
the introduction of platform_suspend_ops in checkpatch.pl's list of "should
be const" structs (79404849e9).
Patch against mainline.
Inspired by hunks of the grsecurity patch, updated for newer kernels.
Signed-off-by: Lionel Debroux <lionel_debroux@yahoo.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Make use the newly added method to pass platform data for wl1251 too.
This allows to eliminate some redundant code.
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add hwmod structures for I2C controllers on OMAP3430.
This patch was developed in collaboration with Paul Walmsley
<paul@pwsan.com>.
OMAP3 fixes for correct IDLEST bit monitoring from
G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add hwmod structures for I2C controllers on OMAP2420/2430.
NOTE: I2C module on OMAP2420 has 16bit registers and causes imprecise
aborts if 32bits are read/written to it. Use the HWMOD_16BIT_REG flag
to notify the hmwod framework of this hard requirement so that
__raw_writew/readw is used to read /write the mdoule registers.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Set onenand_setup to NULL instead of adding a no-op function.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes the following error:
>regulator: VMMC1: 1850 <--> 3150 mV at 3000 mV normal standby
>twl_reg twl_reg.6: can't register VMMC1, -22
>twl_reg: probe of twl_reg.6 failed with error -22
Signed-off-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (215 commits)
ARM: memblock: setup lowmem mappings using memblock
ARM: memblock: move meminfo into find_limits directly
ARM: memblock: convert free_highpages() to use memblock
ARM: move freeing of highmem pages out of mem_init()
ARM: memblock: convert memory detail printing to use memblock
ARM: memblock: use memblock to free memory into arm_bootmem_init()
ARM: memblock: use memblock when initializing memory allocators
ARM: ensure membank array is always sorted
ARM: 6466/1: implement flush_icache_all for the rest of the CPUs
ARM: 6464/2: fix spinlock recursion in adjust_pte()
ARM: fix memblock breakage
ARM: 6465/1: Fix data abort accessing proc_info from __lookup_processor_type
ARM: 6460/1: ixp2000: fix type of ixp2000_timer_interrupt
ARM: 6449/1: Fix for compiler warning of uninitialized variable.
ARM: 6445/1: fixup TCM memory types
ARM: imx: Add wake functionality to GPIO
ARM: mx5: Add gpio-keys to mx51 babbage board
ARM: imx: Add gpio-keys to plat-mxc
mx31_3ds: Fix spi registration
mx31_3ds: Fix the logic for detecting the debug board
...
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030. This functionality was introduced in mfd tree on
track to kernel.org
Sync pandaboard to the same and make mmc work.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Adding card detect callback function and card detect configuration
function for MMC1 Controller on OMAP4.
Card detect configuration function does initial configuration of the
MMC Control & PullUp-PullDown registers of Phoenix.
For MMC1 Controller, card detect interrupt source is
twl6030 which is non-gpio. The card detect call back function provides
card present/absent status by reading MMC Control register present
on twl6030.
Since OMAP4 doesn't use any GPIO line as used in OMAP3 for card detect,
the suspend/resume initialization which was done in omap_hsmmc_gpio_init
previously is moved to the probe thus making it generic for both OMAP3 &
OMAP4.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This merges the staging-next tree to Linus's tree and resolves
some conflicts that were present due to changes in other trees that were
affected by files here.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.infradead.org/battery-2.6:
power_supply: Makefile cleanup
bq27x00_battery: Add missing kfree(di->bus) in bq27x00_battery_remove()
power_supply: Introduce maximum current property
power_supply: Add types for USB chargers
ds2782_battery: Fix units
power_supply: Add driver for TWL4030/TPS65950 BCI charger
bq20z75: Add support for more power supply properties
wm831x_power: Add missing kfree(wm831x_power) in wm831x_power_remove()
jz4740-battery: Add missing kfree(jz_battery) in jz_battery_remove()
ds2760_battery: Add missing kfree(di) in ds2760_battery_remove()
olpc_battery: Fix endian neutral breakage for s16 values
ds2760_battery: Fix W1 and W1_SLAVE_DS2760 dependency
pcf50633-charger: Add missing sysfs_remove_group()
power_supply: Add driver for TI BQ20Z75 gas gauge IC
wm831x_power: Remove duplicate chg mask
omap: rx51: Add support for USB chargers
power_supply: Add isp1704 charger detection driver
The machine_kexec() calls outer_disable which can crash on OMAP4
becasue of trustzone restrictions.
This patch overrides the default l2x0_disable with a OMAP4
specific implementation taking care of trustzone
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
* 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (163 commits)
omap: complete removal of machine_desc.io_pg_offst and .phys_io
omap: UART: fix wakeup registers for OMAP24xx UART2
omap: Fix spotty MMC voltages
ASoC: OMAP4: MCPDM: Remove unnecessary include of plat/control.h
serial: omap-serial: fix signess error
OMAP3: DMA: Errata i541: sDMA FIFO draining does not finish
omap: dma: Fix buffering disable bit setting for omap24xx
omap: serial: Fix the boot-up crash/reboot without CONFIG_PM
OMAP3: PM: fix scratchpad memory accesses for off-mode
omap4: pandaboard: enable the ehci port on pandaboard
omap4: pandaboard: Fix the init if CONFIG_MMC_OMAP_HS is not set
omap4: pandaboard: remove unused hsmmc definition
OMAP: McBSP: Remove null omap44xx ops comment
OMAP: McBSP: Swap CLKS source definition
OMAP: McBSP: Fix CLKR and FSR signal muxing
OMAP2+: clock: reduce the amount of standard debugging while disabling unused clocks
OMAP: control: move plat-omap/control.h to mach-omap2/control.h
OMAP: split plat-omap/common.c
OMAP: McBSP: implement functional clock switching via clock framework
OMAP: McBSP: implement McBSP CLKR and FSR signal muxing via mach-omap2/mcbsp.c
...
Fixed up trivial conflicts in arch/arm/mach-omap2/
{board-zoom-peripherals.c,devices.c} as per Tony
* 'davinci-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-davinci: (50 commits)
davinci: fix remaining board support after io_pgoffst removal
davinci: mityomapl138: make file local data static
arm/davinci: remove duplicated include
davinci: Initial support for Omapl138-Hawkboard
davinci: MityDSP-L138/MityARM-1808 read MAC address from I2C Prom
davinci: add tnetv107x touchscreen platform device
input: add driver for tnetv107x touchscreen controller
davinci: add keypad config for tnetv107x evm board
davinci: add tnetv107x keypad platform device
input: add driver for tnetv107x on-chip keypad controller
net: davinci_emac: cleanup unused cpdma code
net: davinci_emac: switch to new cpdma layer
net: davinci_emac: separate out cpdma code
net: davinci_emac: cleanup unused mdio emac code
omap: cleanup unused davinci mdio arch code
davinci: cleanup mdio arch code and switch to phy_id
net: davinci_emac: switch to new mdio
omap: add mdio platform devices
davinci: add mdio platform devices
net: davinci_emac: separate out davinci mdio
...
Fix up trivial conflict in drivers/input/keyboard/Kconfig (two entries
added next to each other - one from the davinci merge, one from the
input merge)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: (365 commits)
ALSA: hda - Disable sticky PCM stream assignment for AD codecs
ALSA: usb - Creative USB X-Fi volume knob support
ALSA: ca0106: Use card specific dac id for mute controls.
ALSA: ca0106: Allow different sound cards to use different SPI channel mappings.
ALSA: ca0106: Create a nice spot for mapping channels to dacs.
ALSA: ca0106: Move enabling of front dac out of hardcoded setup sequence.
ALSA: ca0106: Pull out dac powering routine into separate function.
ALSA: ca0106 - add Sound Blaster 5.1vx info.
ASoC: tlv320dac33: Use usleep_range for delays
ALSA: usb-audio: add Novation Launchpad support
ALSA: hda - Add workarounds for CT-IBG controllers
ALSA: hda - Fix wrong TLV mute bit for STAC/IDT codecs
ASoC: tpa6130a2: Error handling for broken chip
ASoC: max98088: Staticise m98088_eq_band
ASoC: soc-core: Fix codec->name memory leak
ALSA: hda - Apply ideapad quirk to Acer laptops with Cxt5066
ALSA: hda - Add some workarounds for Creative IBG
ALSA: hda - Fix wrong SPDIF NID assignment for CA0110
ALSA: hda - Fix codec rename rules for ALC662-compatible codecs
ALSA: hda - Add alc_init_jacks() call to other codecs
...
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: Makefile - replace the use of <module>-objs with <module>-y
crypto: hifn_795x - use cancel_delayed_work_sync()
crypto: talitos - sparse check endian fixes
crypto: talitos - fix checkpatch warning
crypto: talitos - fix warning: 'alg' may be used uninitialized in this function
crypto: cryptd - Adding the AEAD interface type support to cryptd
crypto: n2_crypto - Niagara2 driver needs to depend upon CRYPTO_DES
crypto: Kconfig - update broken web addresses
crypto: omap-sham - Adjust DMA parameters
crypto: fips - FIPS requires algorithm self-tests
crypto: omap-aes - OMAP2/3 AES hw accelerator driver
crypto: updates to enable omap aes
padata: add missing __percpu markup in include/linux/padata.h
MAINTAINERS: Add maintainer entries for padata/pcrypt
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (141 commits)
USB: mct_u232: fix broken close
USB: gadget: amd5536udc.c: fix error path
USB: imx21-hcd - fix off by one resource size calculation
usb: gadget: fix Kconfig warning
usb: r8a66597-udc: Add processing when USB was removed.
mxc_udc: add workaround for ENGcm09152 for i.MX35
USB: ftdi_sio: add device ids for ScienceScope
USB: musb: AM35x: Workaround for fifo read issue
USB: musb: add musb support for AM35x
USB: AM35x: Add musb support
usb: Fix linker errors with CONFIG_PM=n
USB: ohci-sh - use resource_size instead of defining its own resource_len macro
USB: isp1362-hcd - use resource_size instead of defining its own resource_len macro
USB: isp116x-hcd - use resource_size instead of defining its own resource_len macro
USB: xhci: Fix compile error when CONFIG_PM=n
USB: accept some invalid ep0-maxpacket values
USB: xHCI: PCI power management implementation
USB: xHCI: bus power management implementation
USB: xHCI: port remote wakeup implementation
USB: xHCI: port power management implementation
...
Manually fix up (non-data) conflict: the SCSI merge gad renamed the
'hw_sector_size' member to 'physical_block_size', and the USB tree
brought a new use of it.
Commit ab69bcd66f (arm: remove
machine_desc.io_pg_offst and .phys_io) could not update
the new boards in the omap tree. This causes the build of
omap2plus_defconfig to fail. Fix this.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Eric Miao <eric.miao at canonical.com>
[tony@atomide.com: updated description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP24xx, UART2 WKEN and WKST registers are in PM_WKEN2_CORE and
PM_WKST2_CORE respecitvely. Fix the OMAP2 register init to use the
correct registers on OMAP24xx.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM35x has musb interface (version 1.8) and uses CPPI41 DMA engine.
It has USB phy built inside the IP itself.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since we're now using addruart to establish the debug mapping, we can
remove the io_pg_offst and phys_io members of struct machine_desc.
The various declarations were removed using the following script:
grep -rl MACHINE_START arch/arm | xargs \
sed -i '/MACHINE_START/,/MACHINE_END/ { /\.\(phys_io\|io_pg_offst\)/d }'
[ Initial patch was from Jeremy Kerr, example script from Russell King ]
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
Acked-by: Eric Miao <eric.miao at canonical.com>
Rather than checking the MMU status in every instance of addruart, do it
once in kernel/debug.S, and change the existing addruart macros to
return both physical and virtual addresses. The main debug code can then
select the appropriate address to use.
This will also allow us to retreive the address of a uart for the MMU
state that we're not current in.
Updated with fixes for OMAP from Jason Wang <jason77.wang@gmail.com>
and Tony Lindgren <tony@atomide.com>, and fix for versatile express from
Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>.
Signed-off-by: Jeremy Kerr <jeremy.kerr@canonical.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
The omap2plus_defconfig doesn't boot up when built with CONFIG_PM
disabled on the latest linux-omap master. Below are the observations
1. OMAP3 reboots in the middle of boot
--------------------------------------------------
[ 0.000000] Calibrating delay loop... 494.72 BogoMIPS (lpj=1933312)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] Brought up 1 CPUs
[ 0.000000] SMP: Total of 1 processors activated (494.72 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
U-Boot 1.1.4 (Feb 11 2009 - 16:10:23)
OMAP3430-GP rev 2, CPU-OPP2 L3-165MHz
TI 3430SDP 1.0 Version + mDDR (Boot NOR)
DRAM: 128 MB
Flash: 128 MB
NAND:128 MiB
--------------------------------------------------
2. OMAP4 does a kernel PANIC
-------------------------------------
[ 0.000000] Calibrating delay loop... 1195.29 BogoMIPS (lpj=4669440)
[ 0.000000] pid_max: default: 32768 minimum: 301
[ 0.000000] Security Framework initialized
[ 0.000000] Mount-cache hash table entries: 512
[ 0.000000] CPU: Testing write buffer coherency: ok
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x410000c2, AUX_CTRL 0x0e050000
[ 0.000000] CPU1: Booted secondary processor
[ 0.000000] Brought up 2 CPUs
[ 0.000000] SMP: Total of 2 processors activated (2395.78 BogoMIPS).
[ 0.000000] regulator: core version 0.5
[ 0.000000] NET: Registered protocol family 16
[ 0.000000] mux: Could not set signal i2c2_scl.i2c2_scl
[ 0.000000] mux: Could not set signal i2c2_sda.i2c2_sda
[ 0.000000] mux: Could not set signal i2c3_scl.i2c3_scl
[ 0.000000] mux: Could not set signal i2c3_sda.i2c3_sda
[ 0.000000] mux: Could not set signal i2c4_scl.i2c4_scl
[ 0.000000] mux: Could not set signal i2c4_sda.i2c4_sda
-------------------------------------
This is happening because 'omap_serial_init()' is hanging in the boot.
On OMAP3 the watchdog is generating reboot because devices_init doesn't
happens where as on OMAP4 it just hangs without reboot.
The uart clock is not getting enabled after omap_device_idle as part
of omap_serial_init.
The omap_device_idle(will disable the clock) then omap_uart_block_sleep()
should enable clock back disabled during the boot up phase.
But omap_uart_block_sleep() stuffed version is binded only under
CONFIG_PM and other version is just empty. Hence it is not enabling
clock back as expected
This patch adds uart clock enable code to omap_uart_block_sleep() function
built with CONFIG_PM disabled.
Thanks to Charulatha and Govindraj for their help on this debug.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 914bab936fe0388a529079679e2f137aa4ff548d (OMAP: mach-omap2: Fix
incorrect assignment warnings) changed a pointer from 'u32 *' to
'void *' without also fixing up the pointer arithmetic.
Fix the scratchpad offsets so they are byte offsets instead of
word offsets and thus work correctly with a void pointer base.
Special thanks to Jean Pihet for taking the time track down this
problem and propose an initial solution.
Tested with off-idle and off-suspend on 36xx/Zoom3 and 34xx/omap3evm.
Cc: Manjunath Kondaiah G <manjugk@ti.com>
Reported-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Tested-by: Jean Pihet <jean.pihet@newoldbits.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP4 PandaBoard has EHCI port1 hooked up to an external
SMSC3320 transciever. GPIO 1 is used to power on the transceiver
and GPIO 62 for reset on the transceiver.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid possible crash if CONFIG_MMC_OMAP_HS is not set.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
remove the second hsmmc definition as it is only used on the
expansion header of the PandaBoard and can be mux for other
functions.
Signed-off-by: David Anders <x0132446@ti.com>
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It seems these comments where accidentally added so remove them.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Fix bit clear. Now it clears all other bits than mask bit where it should
clear only it.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Reduce the amount of debugging generated by default when unused clocks
are being disabled by the clock code. The previous code would only
generate debug-level messages, but some people who wished to run
production kernels with debug-level messages enabled reported that the
large number of clock disable messages were slowing boot. Now to
enable clock-by-clock disable messages, DEBUG needs to be defined in
mach-omap2/clock.c.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tuukka Tikkanen <tuukka.tikkanen@nokia.com>
Cc: Tim Bird <tim.bird@am.sony.com>
Only OMAP2+ platforms have the System Control Module (SCM) IP block.
In the past, we've kept the SCM header file in plat-omap. This has
led to abuse - device drivers including it; includes being added that
create implicit dependencies on OMAP2+ builds; etc.
In response, move the SCM headers into mach-omap2/.
As part of this, remove the direct SCM access from the OMAP UDC
driver. It was clearly broken. The UDC code needs an indepth review for
use on OMAP2+ chips.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Cory Maccarrone <darkstar6262@gmail.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Split plat-omap/common.c into three pieces:
1. the 32KiHz sync timer and clocksource code, which now lives in
plat-omap/counter_32k.c;
2. the OMAP2+ common code, which has been moved to mach-omap2/common.c;
3. and the remainder of the OMAP-wide common code, which includes the
deprecated ATAGs code and a deprecated video RAM reservation function.
The primary motivation for doing this is to move the OMAP2+-specific parts
into an OMAP2+-specific file, so that build breakage related to the
System Control Module code can be resolved.
Benoît Cousson <b-cousson@ti.com> suggested a new filename and found
some bugs in the counter_32k.c comments - thanks Benoît.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Previously the OMAP McBSP ASoC driver implemented CLKS switching by
using omap_ctrl_{read,write}l() directly. This is against policy; the OMAP
System Control Module functions are not intended to be exported to drivers.
These symbols are no longer exported, so as a result, the OMAP McBSP ASoC
driver does not build as a module.
Resolve the CLKS clock changing portion of this problem by creating a
clock parent changing function that lives in
arch/arm/mach-omap2/mcbsp.c, and modify the ASoC driver to use it.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, this symbol must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/* and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP ASoC McBSP code implemented CLKR and FSR signal muxing via
direct System Control Module writes on OMAP2+. This required the
omap_ctrl_{read,write}l() functions to be exported, which is against
policy: the only code that should call those functions directly is
OMAP core code, not device drivers. omap_ctrl_{read,write}*() are no
longer exported, so the driver no longer builds as a module.
Fix the pinmuxing part of the problem by removing calls to
omap_ctrl_{read,write}l() from the OMAP ASoC McBSP code and
implementing signal muxing functions in arch/arm/mach-omap2/mcbsp.c.
Due to the unfortunate way that McBSP support is implemented in ASoC
and the OMAP tree, these symbols must be exported for use by
sound/soc/omap/omap-mcbsp.c.
Going forward, the McBSP device driver should be moved from
arch/arm/*omap* into drivers/ or sound/soc/*, and the CPU DAI driver
should be implemented as a platform_driver as many other ASoC CPU DAI
drivers are. These two steps should resolve many of the layering
problems, which will rapidly reappear during a McBSP hwmod/PM runtime
conversion.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The OMAP3 clock tree already contains the infrastructure to support
clock framework-based McBSP functional clock source switching. But it
did not contain the clkdev aliases for the McBSP code to refer to the
parent clocks in an SoC integration-neutral way. So, add the clkdev
aliases for the parent clocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the MCBSP_CLKS clock and the clksel structures needed to support clock
framework-based source switching for McBSPs 1-5. Also, add clkdev
aliases on the parent clocks for the McBSP source switching code, added
in a subsequent patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add the MCBSP_CLKS clock and the clksel structures needed to support clock
framework-based source switching for McBSP 1 and 2. Also, add clkdev
aliases on the parent clocks for the McBSP source switching code, added
in a subsequent patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Currently, if, for example, CONFIG_ARCH_OMAP2420 is not selected, OMAP2420
board files can still be included in the build. This results in link errors:
arch/arm/mach-omap2/built-in.o: In function `omap_generic_map_io':
.../arch/arm/mach-omap2/board-generic.c:51: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_init':
.../arch/arm/mach-omap2/board-h4.c:330: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_h4_map_io':
.../arch/arm/mach-omap2/board-h4.c:373: undefined reference to `omap2_set_globals_242x'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_init':
.../arch/arm/mach-omap2/board-apollon.c:325: undefined reference to `omap2420_mux_init'
arch/arm/mach-omap2/built-in.o: In function `omap_apollon_map_io':
.../arch/arm/mach-omap2/board-apollon.c:353: undefined reference to `omap2_set_globals_242x'
make: *** [.tmp_vmlinux1] Error 1
Fix this by making the boards depend on the Kconfig option for the
specific SoC that they use.
Also, while here, fix the mach-omap2/board-generic.c file to remove the
dependency on OMAP2420.
Charulatha Varadarajan <charu@ti.com> caught a typo - thanks Charu.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Charulatha Varadarajan <charu@ti.com>
As is done on OMAP3, check omap_uart_can_sleep() as one of the
pre-conditions for entering the idle loop. Without this check,
entering idle introduces large latencies on active UARTs, and is
especially noticable on serial console.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some modules which have 16bit registers can cause imprecise
aborts if a __raw_readl/writel is used to read/write 32 bits.
Add an additional flag to identify modules which have such
hard requirement, and handle it in the hwmod framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Inorder to avoid any assumptions from bootloader, the watchdog
timer module is reset during init. This enables the watchdog
timer.
Therefore, it is required to disable WDT after it is reset
during init. Otherwise the system would reboot as per the default
watchdog timer registers settings.
Later, when the watchdog driver is loaded, the watchdog timer settings
is adjusted as per the default timer_margin set in the driver and the
driver would supports the normal operations supported by OMAP watchdog
timer.
Signed-off-by: Charulatha V <charu@ti.com>
Reported-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
VMMC2 regulator is configured but it's not used for the IGEP v2, so
remove this regulator from board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add i2c eeprom driver to access monitor EDID binary information
from user space, something that is required by 'decode-edid' and
'parse-edid'.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There are currently two versions of IGEP v2 board, this patch introduces a
function to detect the hardware revision of IGEP board.
--------------------------
| Id. | Hw Rev. | GPIO 28 |
--------------------------
| 0 | B/C | high |
| 1 | C | low |
--------------------------
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP v2 board has four leds, this patch allows control all
of these LEDs using the LED class if CONFIG_LEDS_GPIO is selected
or using the General Purpose Input/Output (GPIO) interface if
CONFIG_LEDS_GPIO is not selected.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
GPIO for various devices are missing from the board initialization.
This patch adds support for the VBUS and over current gpios. Without this
patch, input/outputs from these two sources are ignored.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP3 IGEP module is a low-power, high performance production-ready
system-on-module (SOM) based on TI's OMAP3 family. More about this
board at www.igep.es.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated for the mmc changes and to be selected by default]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The keypad matrix variable declaration is not matching
with structure variable keymap declared in keypad_matrix.h.
Due to this, following sparse warnings are generated with omap3_defconfig.
arch/arm/mach-omap2/board-devkit8000.c:223:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-devkit8000.c:223:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-devkit8000.c:223:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-ldp.c:107:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-ldp.c:107:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-ldp.c:107:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3evm.c:472:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3evm.c:472:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3evm.c:472:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-3430sdp.c:114:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-3430sdp.c:114:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-3430sdp.c:114:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-rx51-peripherals.c:248:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-zoom-peripherals.c:88:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-cm-t35.c:568:14: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-cm-t35.c:568:14: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-cm-t35.c:568:14: got int static [toplevel] *<noident>
arch/arm/mach-omap2/board-omap3stalker.c:415:13: warning: incorrect type in initializer (different signedness)
arch/arm/mach-omap2/board-omap3stalker.c:415:13: expected unsigned int const [usertype] *keymap
arch/arm/mach-omap2/board-omap3stalker.c:415:13: got int static [toplevel] *<noident>
This patch modifies the variable keymap declaration as per declaration in matrix_keymap structure.
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-input@vger.kernel.org
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/plat-omap/sram.c:130:13: warning: symbol 'omap_detect_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:216:13: warning: symbol 'omap_map_sram' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:450:12: warning: symbol 'omap_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:348:12: warning: symbol 'omap242x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:369:12: warning: symbol 'omap243x_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:425:12: warning: symbol 'omap34xx_sram_init' was not declared. Should it be static?
arch/arm/plat-omap/sram.c:441:12: warning: symbol 'omap44xx_sram_init' was not declared. Should it be static
arch/arm/plat-omap/mcbsp.c:36:6: warning: symbol 'omap_mcbsp_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:50:5: warning: symbol 'omap_mcbsp_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:65:6: warning: symbol 'omap_mcbsp_st_write' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:70:5: warning: symbol 'omap_mcbsp_st_read' was not declared. Should it be static?
arch/arm/plat-omap/mcbsp.c:1648:15: warning: symbol 'omap_st_add' was not declared. Should it be static?
arch/arm/plat-omap/fb.c:414:15: warning: symbol 'omapfb_reserve_sram' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:43:5: warning: symbol 'omap_verify_speed' was not declared. Should it be static?
arch/arm/plat-omap/cpu-omap.c:61:14: warning: symbol 'omap_getspeed' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes miscellaneous sparse warnings in mach-omap2.
arch/arm/mach-omap2/board-am3517evm.c:141:17: warning: Initializer entry defined twice
arch/arm/mach-omap2/board-am3517evm.c:142:18: also defined here
arch/arm/mach-omap2/irq.c:50:35: warning: Using plain integer as NULL pointer
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due non declarations of static functions.
arch/arm/mach-omap2/timer-gp.c:115:12: warning: symbol 'omap2_gp_clockevent_set_gptimer' was not declared. Should it be static?
arch/arm/mach-omap2/powerdomain.c:993:5: warning: symbol 'pwrdm_set_lowpwrstchange' was not declared. Should it be static?
arch/arm/mach-omap2/board-flash.c:141:8: warning: symbol 'board_nand_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:416:6: warning: symbol 'n8x0_mmc_slot1_cover_handler' was not declared. Should it be static?
arch/arm/mach-omap2/board-n8x0.c:544:13: warning: symbol 'n8x0_mmc_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-peripherals.c:902:13: warning: symbol 'rx51_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-video.c:107:13: warning: symbol 'rx51_video_mem_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-debugboard.c:155:12: warning: symbol 'zoom_debugboard_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-zoom-peripherals.c:280:13: warning: symbol 'zoom_peripherals_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-igep0020.c:110:13: warning: symbol 'igep2_flash_init' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:109:6: warning: symbol 'am3517_evm_ethernet_init' was not declared. Should it be static?
drivers/mtd/onenand/omap2.c:577:5: warning: symbol 'omap2_onenand_rephase' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch fixes sparse warnings due to non declaration of
static structures and variables.
Sparse warning logs fixed:
arch/arm/mach-omap2/control.c:88:6: warning: symbol 'omap3_secure_ram_storage' was not declared. Should it be static?
n
arch/arm/mach-omap2/timer-gp.c:50:22: warning: symbol 'gptimer_wakeup' was not declared. Should it be static?
arch/arm/mach-omap2/timer-gp.c:240:18: warning: symbol 'omap_timer' was not declared. Should it be static?
arch/arm/mach-omap2/prcm.c:121:24: warning: symbol 'prcm_context' was not declared. Should it be static?
arch/arm/mach-omap2/mux2420.c:510:29: warning: symbol 'omap2420_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux2430.c:589:29: warning: symbol 'omap2430_pop_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:934:28: warning: symbol 'omap3_cus_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1080:29: warning: symbol 'omap3_cus_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1272:28: warning: symbol 'omap3_cbb_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1393:29: warning: symbol 'omap3_cbb_ball' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1603:28: warning: symbol 'omap36xx_cbp_subset' was not declared. Should it be static?
arch/arm/mach-omap2/mux34xx.c:1821:29: warning: symbol 'omap36xx_cbp_ball' was not declared. Should it be static?
arch/arm/mach-omap2/pm-debug.c:165:15: warning: symbol 'pm_dbg_dir' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:587:30: warning: symbol 'ads7846_config' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3evm.c:606:23: warning: symbol 'omap3evm_spi_board_info' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:46:25: warning: symbol 'rx51_sdrc_params' was not declared. Should it be static?
arch/arm/mach-omap2/board-rx51-sdram.c:211:25: warning: symbol 'rx51_get_sdram_timings' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3touchbook.c:64:15: warning: symbol 'touchbook_revision' was not declared. Should it be static?
arch/arm/mach-omap2/board-am3517evm.c:350:24: warning: symbol 'am3517_evm_dss_device' was not declared. Should it be static?
arch/arm/mach-omap2/board-omap3stalker.c:567:23: warning: symbol 'omap3stalker_spi_board_info' was not declared. Should it be static?
Signed-off-by: Manjunath Kondaiah G <manjugk@ti.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise tidspbridge cannot work.
It looks like this was dropped in the conversion to staging. I took the
liberty of doing some cleaning up.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch "omap: zoom: add mmc3/wl1271 device support" in the
wireless tree still uses .wires in struct omap2_hsmmc_info.
.wires has now been replaced with .caps in patch "omap: mmc:
extended to pass host capabilities from board file" in the
OMAP tree.
This causes linux-next as of 20101001 build to break as
below. Fix this.
CC arch/arm/mach-omap2/board-zoom-peripherals.o
arch/arm/mach-omap2/board-zoom-peripherals.c:217: error: unknown field 'wires' specified in initializer
make[1]: *** [arch/arm/mach-omap2/board-zoom-peripherals.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Ohad Ben-Cohen <ohad@wizery.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
A patch from Sukumar Ghorai <s-ghorai@ti.com> changed the
nwires to use caps instead. However, nwires is still
needed for the earlier controller.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Upcoming ASoC multi-component and OMAP hwmod changes will conflict
in arch/arm/mach-omap2/devices.c. Avoid this by moving a little bit
include statement introduced by ASoC Multi-Component Support patch.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
VMALLOC_END is supposed to be an absolute value, while PAGE_OFFSET may
vary depending on the selected user:kernel memory split mode through
CONFIG_VMSPLIT_*. In fact, the goal of moving PAGE_OFFSET down is to
accommodate more directly addressed RAM by the kernel below the vmalloc
area, and having VMALLOC_END move along PAGE_OFFSET is rather against
the very reason why PAGE_OFFSET can be moved in the first place.
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
On OMAP4, MMC2 controller has eMMC which draws power from VAUX regulator
on TWL. Though the eMMC supports dual voltage[1.8v/3v] as per ocr register,
its VCC is fixed at 3V for operation. With this once the mmc core selects
the minimum voltage[1.8] supported based on the ocr value read from OCR register,
eMMC will not get detected. Thus the platform data for MMC2 is updated with ocr
mask and same will be communicated to core which will set the regulator to
always operate at 3V when ever turned ON.
Cc: Tony Lindgren <tony@atomide.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In OMAP4, as per new PM programming model, the legacy registers
which were there in OMAP3 are all shifted by 0x100 while new one's
are added from offset 0 to 0x10.
For OMAP4, the register offset appending of 0x100 done in devices.c
currently, is moved to driver file.This change fits in for current
implementation as well as once the driver undergoes hwmod adaptation.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Avoid possible crash if CONFIG_MMC_OMAP_HS is not set
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The omap4 es2 hsmmc has a updated soft reset logic.After the
reset is issued monitor a 0->1 transition first. The reset of
CMD or DATA lines is complete only after a 0->1->0 transition
of SRC or SRD bits.
Signed-off-by: Madhusudhan Chikkature <madhu.cr@ti.com>
Tested-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data to make use of newly added charging driver.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Instead of enabling the wifi module explicitly using GPIO, add a fixed
regulator and hook it to MMC host card power control. This way it will
only be enabled when SDIO subsystem wants to talk to it, saving power
(as done by Zoom boards).
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The existing definitions for cpu revision used
upper nibble in the bits[15:08]. With OMAP3630,
definitions use lower nibble.
This patch unifies the definitions to start
at lower nibble.
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 6cdee91257 the references to
enable_off_mode and sleep_while_idle can't be resolved when CONFIG_PM_DEBUG
isn't set:
arch/arm/mach-omap2/built-in.o: In function `omap_uart_restore_context':
arch/arm/mach-omap2/serial.c:253: undefined reference to `enable_off_mode'
arch/arm/mach-omap2/built-in.o: In function `omap3_can_sleep':
arch/arm/mach-omap2/pm34xx.c:479: undefined reference to `sleep_while_idle'
Simply #define these in pm.h just like omap2_pm_debug.
Signed-off-by: Loïc Minier <loic.minier@linaro.org>
[khilman: moved down into existing #ifdef section]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
When checking how to program the next powerstate for the PER
powerdomain, the next state of PER powerdomain was written twice.
Remove the duplicate write.
Reported-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Initialize all omap-uarts for zoom boards. Now zoom_peripheral_init
will initialise all uarts for 3630. 3630sdp_board_init call
zoom_peripheral_init so we can now remove serial_init from 3630sdp
board init as zoom_peripheral_init now will do that the same.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable omap-serial driver in /mach-omap2/Kconfig and
move 8250 driver selection for zoom boards. With omap-serial
driver addition all omap-uarts can be handled with
omap-serial driver.
With addition of omap-serial driver console parameter
needs be changed in bootargs from ttyS* should be
replaced with ttyO* [O --> OMAP not ZERO]
For example: ttyS0[UART1 on 3430SDP] changes to ttyO0.
But with some boards that do not use omap-uart as console uart.
we need to handle them with 8250 driver. Ex: ZOOM2/3.
For zoom2/3 board we need to use 8250 serial driver and
console parameter will remain ttyS0 which basically uses
a Quad uart placed on the debug board connected through a
gpio line.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch makes the following:
- Adds missing wakeup padding register handling.
- Fixes a hardcode to use PER module ONLY on UART3.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add prepare idle and resume idle call for uart4 used by 3630.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
To standarize among other uarts (1 to 3), we shall now:
- Enable uart4 autodile bit.
- Enable uart4 wakeup in PER.
- Allow uart4 to wakeup the MPU.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This is only valid for omap 36xx family of chips.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since the UART enable/idle is done during the idle path (with
interrupts disabled), use the non-locking versions of the hwmod
enable/idle functions.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Since the omap_device for UART is currently managed inside the idle
path itself, don't let the bus-level code suspend/resume the UART.
To prevent this, pm_runtime_get() is used when preparing for suspend
and pm_runtime_put() is used when finished with suspend.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove set_uart_globals function as this will not be needed as
physical address for uarts will be taken from hwmod data file.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Major rework of OMAP UART init for omap_device conversion as well as
use with either 8250 driver or new omap-serial driver.
In preparation for a new omap-serial driver, remove 8250 assumptions
and dependencies from the serial core.
Convert UART core and PM support to use omap_device layer. Also add
support for both console on 8250 or omap-serial driver.
omap_device conversion:
- Convert clock API calls to omap_device calls
- Remove all static platform_data setup and configuration. This is
all done by the omap_device build phase.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch adds omap_hwmod data for UARTs on OMAP2 and OMAP3
platforms.
UART4 support for 3630 and OMAP2 hwmod data added by Govindraj R.
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add uart1-4 hwmod data into omap4_hwmod data file.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch splits omap_init_wdt() into separate omap_init_wdt()
functions under mach-omap1 and mach-omap2 and set them up with
subsys_initcall.
Also it uses omap_device_build() API instead of
platform_device_register() for watchdog timer device registration
for OMAP2plus chips.
For OMAP2plus chips, the device specific data defined in centralized
hwmod database will be used.
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP4 chip
Note: wd_timer3 in enabled in the hwmod list but it is
not yet supported by the watchdog driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP2430 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP2420 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add watchdog timer hwmod data for OMAP3 chip
Signed-off-by: Charulatha V <charu@ti.com>
Acked-by: Cousson, Benoit <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable SMSC911x Ethernet driver for LogicPD's OMAP
3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Introduce of a generic way to setup smsc911x based Ethernet
controller connected to GPMC similar to gpmc-smc91x but without
timing setup.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add low-level initialization for hsmmc controller for
LogicPD's OMAP 3530 LV SOM and OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
[tony@atomide.com: updated for the recent mmc platform init changes]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding support for LogicPD's OMAP 3530 LV SOM and
OMAP 35x Torpedo board.
Signed-off-by: Tim Nordell <tim.nordell@logicpd.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Unnecessary cast from void* in assignment.
Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
add support for hsusb host ports 1, 2 and on-module usb hub.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When changing the L3 clock frequency, the CPU is executing from internal RAM
and the SDRC clock is disabled. During this time accesses made to external
DDR are stalled. If the ARM subsystem attempts to access the DDR while the
SDRC clock is disabled this will stall the CPU until the access to the SDRC
timeouts. A timeout on the SDRC should never occur. Once a timeout occurs all
the following accesses will be aborted and the DDR is no longer accessible.
Although the code being executed in the internal RAM does not directly access
the DDR, it was found that the branch prediction logic in the CPU may cause
the CPU to prefetch code from a DDR location while the SDRC clock is disabled.
This was causing an SDRC timeout which resulted in a system hang.
This patch fixes this problem by ensuring the branch prediction logic is
disabled while changing the L3 clock frequency. The branch prediction logic
is disabled by clearing the Z-bit in the ARM CTRL register.
Disabling the branch prediction logic does not have any noticable impact
on the execution time of this code section. The hardware observability
signals were used to monitor the sdrc idle time with and without this
patch when operating at different CPU frequencies (150MHz, 500MHz and
600MHz) and the total sdrc idle time when changing frequenct was in
the range of 9-11us. This was measured on an omap3430 SDP running the
omapzoom p-android-omap-2.6.29 branch.
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
This patch has multiple fixes together. To ensure that git bisect work across
commits, all changes are clubbed together
1. Move the common control base address to control core
2. Remove the manually coeded defines and use the ones from headers.
3. Fix the the status register define in id.c for OMAP4
4. Fix all the register define in hsmmc.c
5. Use the control pad accessor API for omap4 hsmmc register accesses
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4, control module is divided into 4 separate IPs
- OMAP44XX_CTRL_MODULE_CORE
- OMAP44XX_CTRL_MODULE_PAD_CORE
- OMAP44XX_CTRL_MODULE_WKUP
- OMAP44XX_CTRL_MODULE_PAD_WKUP
This patch adds all the omap4 control module register data and
includes them in the common control.h
The register data is autogenerated from the codebase thanks
to Benoit Cousson efforts
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP4 control pad are not addressable from control
core base. So the common omap_ctrl_read/write APIs breaks
Hence export separate APIs to manage the omap4 pad control
registers.
This APIs will work only for OMAP4
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On omap4 control module is divided in four IP blocks.
- CTRL_MODULE_CORE 0x4a002000
- CTRL_MODULE_PAD_CORE 0x4a100000
- CTRL_MODULE_WKUP 0x4a30c000
- CTRL_MODULE_PAD_WKUP 0x4a31e000
Addressing all the modules with single base address is not possible
considering 16 bit offsets. The mux code manages the pad core and pad
wakeup related base address inside the mux framework. For other usage
only control core and control pad bases are necessary. So this patch
maps only needed pad control base address which is used by device drivers
and infrastructure code
The main control core base is still kept same in this patch to
keep git-bisect working. This will be fixed in the relevant patch
in this series.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Fix a few OMAP4430 clock tree problems after the recent manual merge of the
various ES2 clock patches:
- usim optional clock and its parent had the same name, rename the parent
usim_fclk -> usim_ck
- OPTFCLKEN_CLK32K is not handled anymore by the USBPHYOCP2SCP module in ES2
Create a new clock that belongs to CM_ALWON_USBPHY_CLKCTRL register
This patch depends on some of the PRCM macro updates from Rajendra.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: tweaked patch description]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
DSS on ES2 supports only OSWR, hence remove the support
for CSWR from the powerdomain framework.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
4430 ES2 has a few new registers added and a few modified
from ES1. This patch adds all the register changes in PRM
and CM for OMAP4430 ES2.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
This patch updates the PRM and CM register bitshifts and masks
for OMAP4430 ES2.0.
Replace as well the BITFIELD macro with the shift operator in order
to be consistent with the previous OMAP2 & 3 format.
Sort the register list in comments in order to have a consistent
register order and avoid futur change during code generation.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
OMAP4 IP optional clocks require explicit enable in module CTRLCLK
register. In order to allow that we have to create artificial clock
nodes that represent this clock inputs in the IP.
Notes:
- Temporary use OMAP3 names for GPIO optional clocks until the GPIO hwmod
convertion is done. It will enforce the usage of OMAP4 names as the reference.
- Temporary use OMAP3 names for TIMER main clock (gptX_fck) until TIMER hwmod
convertion is done. During that convertion, the new name will have to be used.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
The OMAP4 hwmod data introduced the new naming convention for TI
IPs (See patch OMAP4: hwmod: Add partial hwmod support for OMAP4430 ES1.0)
The leaf clock names are using the same IP name and thus must be
modified to match the clock populated in the hwmod data.
- Fix some leaf clocks nodes that were using a _iclk instead of the _fclk
prefix.
- Fix some wrong interface clock name for master IPs connected to
interconnect.
Please not that due to the fact that nodes are sorted by name, the name
change will introduce a quite ugly diff a little bit hard to follow.
Timers clock con_id is still using the old gptX_fck name until the
gptimer driver is updated to omap_device framework.
Timers entries in hwmods DB are still disabled until the migration
if timer to platform_driver + omap_hwmod.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: manually resolved conflicts with Rajendra's clock patch]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Rajendra Nayak <rnayak@ti.com>
This patch updates the clock tree with all the
changes in OMAP4430 ES2.
clock nodes added
-1- tie_low_clock_ck
-2- abe_dpll_bypass_clk_mux_ck
clock nodes deleted
-1- dpll_sys_ref_clk
-2- per_sgx_fclk
-3- usbphyocp2scp_ick
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoît Cousson <b-cousson@ti.com>
[paul@pwsan.com: added comment re ES1 clocks to top of file]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
wires variable is renamed, extended and this single variable to be used to
pass the platform capabilities, e.g DDR mode. Also removed the hardcoded
value was using as bus-width.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
