Some controllers (VIA CX700) raise device error on SETXFER even after
mode configuration succeeded. Update ata_dev_set_mode() such that
device error is ignored if transfer mode is configured correctly. To
implement this, device is revalidated even after device error on
SETXFER.
This fixes kernel bugzilla bug 8563.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes the following section mismatches:
<-- snip -->
...
WARNING: drivers/ata/built-in.o(.text+0x15072): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_init_sata_map()
WARNING: drivers/ata/built-in.o(.text+0x150dd): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_init_pcs()
WARNING: drivers/ata/built-in.o(.text+0x150e5): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_init_sidpr()
WARNING: drivers/ata/built-in.o(.text+0x15107): Section mismatch in reference from the function piix_init_one() to the function .devinit.text:piix_check_450nx_errata()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maybe for the trivial tree...
sata_via.c has PATA support since:
d73f30e1c9
sata_via: PATA support
AFAICS so the TODO list is no longer true.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The HITACHI HDS7250SASUN500G and HITACHI HDS7225SBSUN250 drives
do not need to be blacklisted, the NCQ problem has been resolved
with the "sata_nv: fix for completion handling" patch.
Signed-off-by David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This fixes some problems with ATAPI devices on nForce4 controllers in ADMA mode
on systems with memory located above 4GB. We need to delay setting the 64-bit
DMA mask until the PRD table and padding buffer are allocated so that they don't
get allocated above 4GB and break legacy mode (which is needed for ATAPI
devices). Also, if either port is in ATAPI mode we need to set the DMA mask
for the PCI device to 32-bit to ensure that the IOMMU code properly bounces
requests above 4GB, as it appears setting the bounce limit does not guarantee
that we will not try to map requests above this point.
Reported to fix https://bugzilla.redhat.com/show_bug.cgi?id=351451
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
mips:
drivers/ata/sata_mv.c: In function `mv_port_free_dma_mem':
drivers/ata/sata_mv.c:1080: error: implicit declaration of function `dma_pool_free'
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
qc->n_iter was used for libata's own sg walking before sg chaining
replaced it. During conversion, the field and its usage in sata_fsl
were left behind. Kill the filed and update sata_fsl.
tj: This was part of James's libata-use-block-layer-padding patch.
Separated out by me.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AHCI uses CAP.NP to indicate the number of ports and PI to tell which
ports are enabled. The only requirement is that the number of ports
indicated by CAP.NP should equal or be higher than the number of
enabled ports in PI.
CAP.NP and PI carry duplicate information and there have been some
interesting cases. Some early AHCI controllers didn't set PI at all
and just implement from port 0 to CAP.NP. An ICH8 board which wired
four out of six available ports had 3 (4 ports) for CAP.NP and 0x33
for PI. While ESB2 has less bits set in PI than the value in CAP.NP.
Till now, ahci driver assumed that PI is invalid if it doesn't match
CAP.NP exactly. This violates AHCI standard and the driver ends up
accessing unmimplemented ports on ESB2.
This patch updates CAP.NP and PI handling such that PI can have less
number of bits set than indicated in CAP.NP and the highest port is
determined as the maximum port of what CAP.NP and PI indicate.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Marvell's Orion SoC includes SATA controllers based on Marvell's
PCI-to-SATA 88SX controllers. This patch extends the libATA sata_mv
driver to support those controllers.
[edited to use linux/ata_platform.h -jg]
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This sets the segment size limit properly via pci_set_dma_max_seg_size
and remove blk_queue_max_segment_size because scsi-ml calls it.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch is based on an original patch from Kuan Luo of NVIDIA,
posted under subject "fixed a bug of adma in rhel4u5 with HDS7250SASUN500G".
His description follows. I've reworked it a bit to avoid some unnecessary
repeated checks but it should be functionally identical.
"The patch is to solve the error message "ata1: CPB flags CMD err,
flags=0x11" when testing HDS7250SASUN500G in rhel4u5.
I tested this hd in 2.6.24-rc7 which needed to remove the mask in
blacklist to run the ncq and the same error also showed up.
I traced the bug and found that the interrupt finished a command (for
example, tag=0) when the driver got that adma status is
NV_ADMA_STAT_DONE and cpb->resp_flags is NV_CPB_RESP_DONE.
However, For this hd, the drive maybe didn't clear bit 0 at this moment.
It meaned the hardware had not completely finished the command.
If at the same time the driver freed the command(tag 0) and sended
another command (tag 0), the error happened.
The notifier register is 32-bit register containing notifier value.
Value is bit vector containing one bit per tag number (0-31) in
corresponding bit positions (bit 0 is for tag 0, etc). When bit is set
then ADMA indicates that command with corresponding tag number completed
execution.
So i added the check notifier code. Sometimes i saw that the notifier
reg set some bits , but the adma status set NV_ADMA_STAT_CMD_COMPLETE
,not NV_ADMA_STAT_DONE. So i added the NV_ADMA_STAT_CMD_COMPLETE check
code."
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The integrated SATA controller is connected directly to the SoC's
internal bus, not via PCI interface. this patch removes the dependency
on the PCI interface.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove some obsolete comments, and bump up the driver version number.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This driver currently has no need for the .post_internal_cmd op.
So get rid of it, to save unnecessary transitions between EDMA and non-EDMA modes.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Final changes to actually turn on NCQ in the driver for GEN_II/IIE hardware.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In preparation for supporting NCQ, we must allocate separate SG tables
for each command tag, rather than just a single table per port as before.
Gen-I hardware cannot do NCQ, though, so we still allocate just a single
table for that, but populate it in all 32 slots to avoid special-cases
elsewhere in hotter paths of the code.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the Intel ICH10 IDE mode SATA Controller DeviceID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the Intel ICH10 SATA RAID Controllers DeviceID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Create host-owned DMA memory pools, for use in allocating/freeing per-port
command/response queues and SG tables. This gives us a way to guarantee we
meet the hardware address alignment requirements, and also reduces memory that
might otherwise be wasted on alignment gaps.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The GenII chips have only 8-bits for the sector_count field when performing NCQ.
Add a dev_config method to restrict this when necessary, taking care not to
override any other restriction already in place (likely none, but someday.. ?).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify tag handling by using the cid/hqtag field instead of ioid,
as recommended by Marvell.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
An extra EDMA config bit is required for NCQ operation.
So set/clear it as needed, and cache current setting in port_priv.
For now though, it will always be "off" (0).
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Simplify and fix EDMA configuration setup to match Marvell specificiations.
The chip documentation gives a specific (re)init sequence, which we now follow.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use naming consistent with elsewhere in this driver.
This will keep things less confusing when we later add "hc_mmio" in this function.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The chips can handle many transient errors internally without a software IRQ.
We now mask/ignore those interrupts here. This is necessary for NCQ, later on.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A hard reset is necessary after hotplug events.
Only clear the error irq bits that were set on entry.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The documentation for ata_data_xfer and ata_data_xfer_noirq had the 'rw'
parameter named 'write_data'.
Signed-off-by: Linus Nilsson <lajnold@acc.umu.se>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mpc8315 shares the same SATA controller as the mpc837x,
and likelihood is that future SoCs from Freescale will also.
Signed-off-by: Jerry Huang <Chang-Ming.Huang@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Update MPC5200 drivers to also look for compatible properties in the
form "fsl,mpc5200-*" to better conform to open firmware generic names
recommended practice as published here:
http://www.openfirmware.org/1275/practice/gnames/gnamv14a.html
This patch should *not* break compatibility with older device trees
which do not use the 'fsl,' prefix. The drivers will still bind against
the older names also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (200 commits)
[SCSI] usbstorage: use last_sector_bug flag universally
[SCSI] libsas: abstract STP task status into a function
[SCSI] ultrastor: clean up inline asm warnings
[SCSI] aic7xxx: fix firmware build
[SCSI] aacraid: fib context lock for management ioctls
[SCSI] ch: remove forward declarations
[SCSI] ch: fix device minor number management bug
[SCSI] ch: handle class_device_create failure properly
[SCSI] NCR5380: fix section mismatch
[SCSI] sg: fix /proc/scsi/sg/devices when no SCSI devices
[SCSI] IB/iSER: add logical unit reset support
[SCSI] don't use __GFP_DMA for sense buffers if not required
[SCSI] use dynamically allocated sense buffer
[SCSI] scsi.h: add macro for enclosure bit of inquiry data
[SCSI] sd: add fix for devices with last sector access problems
[SCSI] fix pcmcia compile problem
[SCSI] aacraid: add Voodoo Lite class of cards.
[SCSI] aacraid: add new driver features flags
[SCSI] qla2xxx: Update version number to 8.02.00-k7.
[SCSI] qla2xxx: Issue correct MBC_INITIALIZE_FIRMWARE command.
...
Hugh Dickens noticed that SMART commands issued from user space can
end up corupting memory. The problem occurs if the buffer used to
read data spans two pages. The reason is that the PIO sector routines
in libata are expecting physically contiguous pages when they do
sector operations, so the left overs on the second page go into the
next physically adjacent page rather than the next page in the sg
mapping.
Fix this by enforcing strict 512 byte alignment on all buffers from
userspace.
Acked-by: Hugh Dickins <hugh@veritas.com>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
drivers/ata/sata_fsl.c: In function 'sata_fsl_fill_sg':
drivers/ata/sata_fsl.c:337: error: redeclaration of 'si' with no linkage
drivers/ata/sata_fsl.c:326: error: previous declaration of 'si' was here
Reported-by: Olof Johansson <olof@lixom.net>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This puts winbond VLB in with the other ISA/VLB support and means we can
lose pata_winbond.c. With all the VLB/ISA probe in one space (and out of
the core libata) this makes legacy probing work sanely.
Also switch to devm_ for resource handling on the ports post probe
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Minor tidying up. Only real change is to return UNK not 80 wire when we
don't know the cable type. This didn't use to matter but with Tejun's
reworking of cable detection it may.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_irq is always assigned so does not need to be initialised to zero.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_ECAT_DUBIOUS_BASE was too high by one and thus all DUBIOUS error
categorizations were wrong. This passed test because only ATA_BUS and
UNK_DEV were used during testing and the ones after them - ATA_BUS and
an overflowed entry - behaved similarly.
This patch fixes the problem by adding DUBIOUS_NONE category and use
it as base.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Factor out AHCI enabling into ahci_enable_ahci() and enabling AHCI
before reading CAP in ahci_save_initial_config() as the spec requires
enabling AHCI mode before accessing any other registers.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For ICH8, SCRs can be accessed using index and data register pair
located at BAR 5. This patch implements support for it such that PHY
status, errors and hardreset are available for those controllers.
This is the only case where two devices on a PATA channel have access
to SCRs and creates a unique problem of mapping two SCRs to one link.
Note that this is different from PMP case in that they aren't quite
separate links - e.g. softreset resets both devices.
This problem is worked around by merging the SCR values. To upper
layer, it looks like there is a single link with one set of SCRs but
with two devices. This works well enough for PHY event, error
reporting and hardreset.
Supporting hardreset is important because in rare cases SATA devices
fail to recover without it after PHY errors.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_piix requires more configuration during initialization than most
other SFF compliant controllers and one-go initialzation with
ata_pci_one() is too rigid.
This patch converts ata_piix to use two step prepare - activate
initialization used by other more advanced controllers. This
conversion brings the happy side effect of enabling PCI device before
accessing PCI configuration registers. Other than that, there
shouldn't be any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Factor out ata_pci_activate_sff_host() from ata_pci_one(). This does
about the same thing as ata_host_activate() but needs to be separate
because SFF controllers use different and multiple IRQs in legacy
mode.
This will be used to make SFF LLD initialization more flexible.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the legacy driver so it can handle VLB ports nicely, and has an
internal structure for nailing new ISA/VLB forms in. Anyone got an ALI14xx
and a spare day ;)
Also adds an "all" parameter so you can load this driver after all the PCI
ones in a boot time kernel and tell it to grab anything ST412 compatible
even if it is an unknown PCI device. That allows libata to offer the same
"just get me a disk somehow" fallback that old IDE did.
Obsoletes pata_qdi.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/spi/Kconfig:156:warning: 'select' used by config symbol 'SPI_PXA2XX' refers to undefined symbol 'PXA_SSP'
drivers/ata/pata_winbond.c: In function 'winbond_data_xfer':
drivers/ata/pata_winbond.c:109: error: 'read' undeclared (first use in this function)
drivers/ata/pata_winbond.c:109: error: (Each undeclared identifier is reported only once
drivers/ata/pata_winbond.c:109: error: for each function it appears in.)
drivers/ata/pata_winbond.c:123: warning: 'return' with a value, in function returning void
drivers/ata/pata_winbond.c: At top level:
drivers/ata/pata_winbond.c:162: warning: initialization from incompatible pointer type
distcc[29718] ERROR: compile drivers/ata/pata_winbond.c on bix/8 failed
make[1]: *** [drivers/ata/pata_winbond.o] Error 1
make: *** [drivers/ata/pata_winbond.o] Error 2
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While merging data_xfer prototype change, pata_pcmcia was left out.
Convert it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata-sff code used DRV_NAME which is hardcoded to "libata" when
requesting resources. Use dev_driver_string() such that low level
driver names are used in resource listing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Kill PIIX_FLAG_SCR, PIIX_PORT_ENABLED and PIIX_PORT_PRESENT. These
are unused.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port_queue_task() served a single user: ata_pio_task()
Rename to ata_pio_queue_task() and un-export it, as nobody outside of
libata-core.c uses it.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some it821x RAID firmwares return 0 for the err return off both devices.
A similar issue occurs with the slave returning 0 not 1 if you plug a
gigabyte sata ramdisk into a controller that fakes two SATA ports as
master/slave on an SFF channel.
The patch does the following
- Allow the 'failed diagnostics' case on both master and slave
- Move the HORKAGE_DIAGNOSTIC check after ->dev_config
This second change also allows IT821x to fix up a problem where we report
drive diagnostic failures when in fact the drive is fine but the
microcontroller firmware doesn't appear to get it right. IT821x clears
the flag again to avoid giving the user bogus warnings about their disk.
The other IT821x change is a bit ugly, we slightly abuse the cable type
hook to fiddle with the identify data for the devices. We could add a new
hook for this but as we have only one offender and no more seeming likely
it seems better to keep libata-core clean.
Please let this sit in -mm briefly, just in case the relaxed checking
breaks some other emulated interface.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
qc->nbytes didn't use to include extra buffers setup by libata core
layer and my be odd. This patch makes qc->nbytes include any extra
buffers setup by libata core layer and guaranteed to be aligned on 4
byte boundary.
This value is to be used to program the host controller. As this
represents the actual length of buffer available to the controller and
the controller must be able to deal with short transfers for ATAPI
commands which can transfer variable length, this shouldn't break any
controllers while making problems like rounding-down and controllers
choking up on odd transfer bytes much less likely.
The unmodified value is stored in new field qc->raw_nbytes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata used private sg iterator to handle padding sg. Now that sg can
be chained, padding can be handled using standard sg ops. Convert to
chained sg.
* s/qc->__sg/qc->sg/
* s/qc->pad_sgent/qc->extra_sg[]/. Because chaining consumes one sg
entry. There need to be two extra sg entries. The renaming is also
for future addition of other extra sg entries.
* Padding setup is moved into ata_sg_setup_extra() which is organized
in a way that future addition of other extra sg entries is easy.
* qc->orig_n_elem is unused and removed.
* qc->n_elem now contains the number of sg entries that LLDs should
map. qc->mapped_n_elem is added to carry the original number of
mapped sgs for unmapping.
* The last sg of the original sg list is used to chain to extra sg
list. The original last sg is pointed to by qc->last_sg and the
content is stored in qc->saved_last_sg. It's restored during
ata_sg_clean().
* All sg walking code has been updated. Unnecessary assertions and
checks for conditions the core layer already guarantees are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_QCFLAG_DMAMAP was a bit peculiar in that it got set during qc
initialization and cleared if DMA mapping wasn't necessary. Make it
more straight forward by making the following changes.
* Don't set it during initialization. Set it after DMA is actually
mapped.
* Add BUG_ON() to guarantee that there is data to transfer if DMAMAP
is set. This always holds for the current code. The BUG_ON() is
for docummentation and sanity check.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With atapi_request_sense() converted to use sg, there's no user of
non-sg interface. Kill non-sg interface.
* ATA_QCFLAG_SINGLE and ATA_QCFLAG_SG are removed. ATA_QCFLAG_DMAMAP
is used instead. (this way no LLD change is necessary)
* qc->buf_virt is removed.
* ata_sg_init_one() and ata_sg_setup_one() are removed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Depending on how many bytes are transferred as a unit, PIO data
transfer may consume more bytes than requested. Knowing how much
data is consumed is necessary to determine how much is left for
draining. This patch update ->data_xfer such that it returns the
number of consumed bytes.
While at it, it also makes the following changes.
* s/adev/dev/
* use READ/WRITE constants for rw indication
* misc clean ups
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_PROT_ATAPI_* are ugly and naming schemes between ATA_PROT_* and
ATA_PROT_ATAPI_* are inconsistent causing confusion. Rename them to
ATAPI_PROT_* and make them consistent with ATA counterpart.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Treat zero xfer length as HSM violation. While at it, add
unlikely()'s to ATAPI ireason and transfer length checks.
tj: Formatted patch and added unlikely()'s.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
atapi_request_sense() is now the only left user of ata_sg_init_one().
Convert it to use sg interface.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Rusty Russel <rusty@rustcorp.com.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I missed one while converting to ata_is_*() protocol test helpers.
Convert it. Pointed out by Jeff Garzik.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: line over 80 characters
#70: FILE: drivers/ata/pata_hpt37x.c:850:
+ struct pci_dev *pdev_0 = pci_get_slot(pdev->bus, pdev->devfn - 1);
ERROR: else should follow close brace '}'
#78: FILE: drivers/ata/pata_hpt37x.c:858:
+ }
+ else
total: 1 errors, 1 warnings, 100 lines checked
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/libata-eh.c: In function `ata_port_pbar_desc':
drivers/ata/libata-eh.c:215: warning: long long unsigned int format, long unsigned int arg (arg 4)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Cable detection on NV PATA hosts isn't implemented and the CBLID-
cable isn't wired according to the sepc either, so both host-side and
generic drive-side cable detections are broken. Till now,
nv_cable_detect() relied on peeking BIOS and ACPI configurations to
upgrade to 80C but this often results in misdetection of 40C cable as
80C. Also, the original implementation was broken in that by the time
BIOS configuration is read it has already been cleared by programming
PIO0 during reset.
This patch reimplements NV mode selection such that...
* BIOS configuration value is stored during driver attach and restored
on detach.
* Cable type is fixed to ATA_CBL_PATA_IGN and mode selection is soley
done by nv_mode_filter() which peeks both BIOS and ACPI
configurations and filter accordingly.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement ata_acpi_cbl_80wire() using ata_acpi_gtm_xfermask() and
while at it relocate the function below ata_acpi_gtm_xfermask().
New ata_acpi_cbl_80wire() implementation takes @gtm, in both pata_via
and pata_amd, use the initial GTM value. Both are trying to peek
initial BIOS configuration, so using initial caching value makes
sense. This fixes ACPI part of cable detection in pata_amd which
previously always returned 0 because configuring PIO0 during reset
clears DMA configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata-acpi is using separate timing tables for transfer modes
although libata-core has the complete ata_timing table. Implement
ata_timing_cycle2mode() to look for matching mode given transfer type
and cycle duration and use it in libata-acpi and pata_acpi to replace
private timing tables.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_acpi_gtm_xfermask() as separated out from pacpi_discover_modes()
has various bugs. Fix them.
* The wrong comparison operator is used when finding for matching
cycle resulting totally bogus result.
* With the comparion operator fixed, boundary condtion handling is
clumsy.
* Setting of any DMA mask bit set all bits in PIO mask.
* MWDMA and UDMA blocks are swapped.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Finding out matching transfer mode from ACPI GTM values is useful for
other purposes too. Separate out the function and timing tables from
pata_acpi::pacpi_discover_modes().
Other than checking shared-configuration bit after doing
ata_acpi_gtm() in pacpi_discover_modes() which should be safe, this
patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate controller IDs into a separate enum as Jeff requested.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make pdc_atapi_pkt() use values from qc->tf instead of creating its
own. This is to ease future ATAPI handling changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_CBL_PATA_UNK indicates that the cable type can't be determined
from the host side and might be either 80c or 40c. libata applies
drive or other generic limit in this case. However, there are
controllers where both host and drive side detections are
misimplemented and the driver has to rely solely on private method -
peeking BIOS or ACPI configuration or using some other private
mechanism.
This patch adds ATA_CBL_PATA_IGN which tells libata to ignore the
cable type completely and just let the LLD determine the transfer mode
via host transfer mode masks and ->mode_filter().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff says xfer_mask is unsigned long not unsigned int. Convert all
xfermask fields and handling functions to deal with unsigned longs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_id_to_dma_mode() isn't quite generic. The function is basically
privately implemented ata_id_xfermask() combined with hardcoded mode
printing and configuration which are specific to ata_generic.
Kill the function and open code it in generic_set_mode() using generic
xfermode handling functions.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* s/ATA_BITS_(PIO|MWDMA|UDMA)/ATA_NR_\1_MODES/g
* Consistently use 0xff to indicate invalid transfer mode (0x00 is
valid for PIO_SLOW).
* Make ata_xfer_mode2mask() return proper mode mask instead of just
the highest bit.
* Sort ata_timing table in increasing xfermode order and update
ata_timing_find_mode() accordingly.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Export the following xfermode related functions.
* ata_pack_xfermask()
* ata_unpack_xfermask()
* ata_xfer_mask2mode()
* ata_xfer_mode2mask()
* ata_xfer_mode2shift()
* ata_mode_string()
* ata_id_xfermask()
* ata_timing_find_mode()
These functions will be used later by LLD updates. While at it,
change unsigned short @speed to u8 @xfer_mode in
ata_timing_find_mode() for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Unindent loop body in generic_set_mode(). This is to ease future
change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It's very likely that the configured data transfer mode is the wrong
one if device fails data transfers right after initial data transfer
mode configuration (including NCQ on/off and xfermode). libata EH
needs to speed down fast before upper layers give up on probing.
This patch implement fast speed down rules to handle such cases
better. Error occured while data transfer hasn't been verified
trigger fast back-to-back speed down actions until data transfer
works.
This change will make cable mis-detection and other initial
configuration problems corrected before partition scanning code gives
up.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_DFLAG_DUBIOUS_XFER is set whenever data transfer speed or method
changes and gets cleared when data transfer command succeeds in the
newly configured transfer mode.
This will be used to improve speed down logic.
Signed-off-by: Tejun Heo <htejun@gmail.com<
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Speed down rules were too conservative. Adjust them a bit.
* More than 10 timeouts can't happen in 5 minutes as command timeout
is 30secs. Lower the limit for rule #1 to 6.
* 10 timeouts is too high for rule #3 too. Lower it to 6.
* SATAPI can benefit from falling back to PIO too. Allow SATAPI
devices to fall back to PIO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up EH speed down implementation.
* is_io boolean variable is replaced eflags. is_io is ATA_EFLAG_IS_IO.
* Error categories now have names.
* Better comments.
* Reorder 5min and 10min rules in ata_eh_speed_down_verdict()
* Use local variable @link to cache @dev->link in ata_eh_speed_down()
These changes are to improve readability and ease further changes.
This patch doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_set_mode() to libata-eh.c. ata_set_mode() is surely an EH
action and will be more tightly coupled with the rest of error
handling. Move it to libata-eh.c.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Factor out ata_eh_schedule_probe() from ata_eh_handle_dev_fail() and
ata_eh_recover(). This is to improve maintainability and make future
changes easier.
In the previous revision, ata_dev_enabled() test was accidentally
dropped while factoring out. This problem was spotted by Bartlomiej.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement protocol tests - ata_is_atapi(), ata_is_nodata(),
ata_is_pio(), ata_is_dma(), ata_is_ncq() and ata_is_data() and use
them to replace is_atapi_taskfile() and hard coded protocol tests.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For intel ones, ahci unconditionally OR'd 0xf to PCS. This isn't
correct for the following cases.
* ich6/7m's which only implement P0 and P2 (0xf works fine tho)
* ich8/9's which have six ports and needs 0x3f to enable all ports
This patch updates PCS programming such that...
* port_map determined by ahci_save_initial_config() is OR'd instead of 0xf
* PCS is updated only if necessary (there are turned off enable bits)
port_map is determined from PORTS_IMPL PCI register which is
implemented as write or write-once register. If the register isn't
programmed, ahci automatically generates it from number of ports,
which is good enough for PCS programming. ICH6/7M are probably the
only ones where non-contiguous enable bits are necessary && PORTS_IMPL
isn't programmed properly but they're proven to work reliably with 0xf
anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Lots of work needed to bring it up to scratch but it does work so you can
now use the card. That makes it at least useful, especially as the other
cardbus cards are usually INIC162x which aren't yet supported well.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Jeff said he preferred that the SFF tf_load followed the spec and we
documented that anyone who needed different overrode it, rather than it
using the ->check_status methods. No driver relies on the current behaviour.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I believe this version meets all Sergei's objections
Correct the logic for when we issue a set features for transfer mode
- If the device has IORDY and the controller has IORDY - set the mode
- If the device has IORDY and the controller does not - turn IORDY off
- If neither has IORDY do nothing
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI spec (ver 3.0a, p289) requires IDE power on/off executes ACPI _PSx
methods. As recently most PATA drivers use libata, this patch adds _PSx
method support in libata. ACPI spec doesn't mention if SATA requires the
same _PSx method.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Len Brown <len.brown@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Historically word 48 in the identify data was used to mean 32bit I/O
was supported for VLB IDE etc. ATA8 reassigns this word to the Trusted
Computing Group, where it is used for TCG features. This means that
an ATA8 TCG drive is going to trigger 32bit I/O on some systems which
will be funny.
Anyway we need to sort this out ready for ATA8 so:
- Reorder the ata.h header a bit so the ata_version function occurs early
in it
- Make dword_io check the ATA version
- Add an ATA8 version checking TCG presence test
While we are at it the current drafts have a flaw where it may not be
possible to disable TCG features at boot (and opt out of the trusted
model) as TCG intends because it relies on presence of a different
optional feature (DCS). Handle this in software by refusing the TCG
commands if libata.allow_tpm is not set. (We must make it possible
as some environments such as proprietary VDR devices will doubtless
want to use it to lock up content)
Finally as with CPRM print a warning so that the user knows they may
not be able to full access and use the device.
Signed-off-by: Alan Cox <alan@redhat.com>
Add Toshiba Satellite R20 and Tecra M6 to broken suspend list. Matt
Piermarini reported and provided the M6 patch. This is from OSDL bug 7780.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Cc: Matt Piermarini <mattpiermarini@yahoo.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PDC202xx older devices do not support ATAPI DMA via the usual
interfaces. What documentation I have isn't sufficient to support DMA and
it isn't clear if the Windows drivers do this or it is possible at all.
(Neither do the drivers/ide old drivers)
So turn it ATAPI DMA off, these are disk optimised controllers.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: line over 80 characters
#36: FILE: drivers/ata/pata_bf54x.c:1512:
+ while (bfin_port_info[board_idx].udma_mask>0 && udma_fsclk[udma_mode] > fsclk) {
ERROR: need spaces around that '>' (ctx:VxV)
#36: FILE: drivers/ata/pata_bf54x.c:1512:
+ while (bfin_port_info[board_idx].udma_mask>0 && udma_fsclk[udma_mode] > fsclk) {
^
total: 1 errors, 1 warnings, 19 lines checked
Your patch has style problems, please review. If any of these errors
are false positives report them to the maintainer, see
CHECKPATCH in MAINTAINERS.
Please run checkpatch prior to sending patches
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sonic Zhang <sonic.zhang@analog.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: sonic zhang <sonic.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In pata_legacy and pata_winbond we've got bugs - cpu_to_le16() instead
of cpu_to_le32(). Fortunately, both affected suckers are VLB, thus
l-e-only, so we might get away with that unless we hit it with slop == 3
(hadn't checked if playing with badly aligned sg could trigger that).
Still buggy... Moreover, pata_legacy, pata_winbond and pata_qdi forgot to
initialize pad on the write side of 32bit case in their ->data_xfer().
Hopefully the hardware does't care, but still, sending uninitialized
data to it...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move electra-ide glue over to the new pata_of_platform framework, and
add the quirks needed to that driver.
Signed-off-by: Olof Johansson <olof@lixom.net>
This driver nicely wraps around pata_platform library functions,
and provides OF platform bus bindings to the PATA devices.
Also add || PPC to the PATA_PLATFORM's "depends on" Kconfig entry,
needed for PA Semi Electra.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Split pata_platform_{probe,remove} into two pieces:
1. pata_platform_{probe,remove} -- platform_device-dependant bits;
2. __ptata_platform_{probe,remove} -- device type neutral bits.
This is done to not duplicate code for the OF-platform driver.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
After 9b8e8de7, manage_start_stop configuration depends on valid ATA
device. Move it into ata_scsi_dev_config(). This was detected by the
coverity checker.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CERR reports errors detected during executing a command. This doesn't
mean the error is tied to the command and can be recovered by just
issuing it again. Many of the errors are fatal port-wide connditions
including HSM violation, host bus error and ATA bus error and require
freezing and port reset.
The freezing part wasn't implemented previously. This used to be okay
because port resets were scheduled anyway and EH eventually resets and
recovers the port. With PMP support added, this is no longer true.
The error condition and recover actions are attributed to the fan-out
port and the host port condition isn't properly recovered leading to
EH failures.
This patch makes CERR errors which require resets to freeze the port.
This will force host port reset and proper recovery.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Andrew Ryder <tireman@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch relaxes the default SCSI DMA alignment from 512 bytes to 4
bytes. I remember from previous discussions that usb and firewire have
sector size alignment requirements, so I upped their alignments in the
respective slave allocs.
The reason for doing this is so that we don't get such a huge amount of
copy overhead in bio_copy_user() for udev. (basically all inquiries it
issues can now be directly mapped).
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix commands timeout with Sil3124/3132 based HBA when pass-through ATA
commands [where ATA_QCFLAG_RESULT_TF is set] are used while other
commands are active on other devices connected to the same port with a
Port Multiplier. Due to a hardware bug, these commands must be sent
alone, like ATAPI commands.
Signed-off-by: Gwendal Grignou <gwendal@google.com>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After non-classifying reset, ehc->classes[] could contain
ATA_DEV_UNKNOWN which used to be normalized to ATA_DEV_NONE for
consistency. However, this causes unfortunate side effect for drivers
which have non-classifying hardresets (e.g. sata_nv) by making
hardreset report ATA_DEV_NONE for non-classifying resets and thus
makes EH believe that the port is unoccupied and recovery can be
skipped. The end result is that after a device is swapped with
another one, the new device isn't attached after the old one is
detached.
This patch makes ata_eh_reset() not normalize UNKNOWN to NONE after
non-classifying resets. This fixes the above problem. As UNKNOWN and
NONE are handled differently by only EH hotplug logic, this doesn't
cause other behavior changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Timeout on downstream command may indicate transmission problem on
host link. Propagate timeouts to host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out distros always enabled burst mode and it is pretty essential so
do the same. Also sort out the post DMA mode restore properly.
My 20263 card now seems happy but needs some four drive tests done yet
(when I've persuaded the kernel not to hang in the edd boot code if I
plug them in ..)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It is legitimate (although annoying and silly) for a PCI IDE controller
not to be assigned an interrupt and to be polled. The libata-sff code
should therefore not try and request IRQ 0 in this case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During conversion to new EH, sata_qstor was accidentaly changed to use
softreset, which is buggy on this chip, instead of hardreset. This
patch updates sata_qstor such that it uses hardreset again.
This fixes bugzilla bug 9631.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With ATAPI transfer chunk size properly programmed, libata PIO HSM
should be able to handle full spurious data chunks. Also, it's a good
idea to suppress trailing data warning for misc ATAPI commands as
there can be many of them per command - for example, if the chunk size
is 16 and the drive tries to transfer 510 bytes, there can be 31
trailing data messages.
This patch makes the following updates to libata ATAPI PIO HSM
implementation.
* Make it drain full spurious chunks.
* Suppress trailing data warning message for misc commands.
* Put limit on how many bytes can be drained.
* If odd, round up consumed bytes and the number of bytes to be
drained. This gets the number of bytes to drain right for drivers
which do 16bit PIO.
This patch is partial backport of improve-ATAPI-data-xfer patchset
pending for #upstream.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
While updating lbam/h for ATAPI commands, atapi_eh_request_sense() was
left out. Update it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement _GTF command filtering which can be controlled by
libata.acpi_filter kernel parameter. Currently SETXFER and LOCK
commands are filtered.
libata configures transfer mode by itself and _GTF SETXFER commands
can potentially disrupt device configuration. _GTM/_STM mechanism
can't handle hotplugging too well and when _GTF is executed,
controller is in PIO0 rather than the mode _STM configured.
Note that detecting SET MAX LOCK requires looking at the previous
command. This adds a bit to code complexity.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As _GTF commands can't transfer data, device error never signals
transfer error. It indicates that the device vetoed the operation, so
it's meaningless to retry.
This patch makes libata-acpi to report and continue on device errors
when executing _GTF commands. Also commands rejected by device don't
contribute to the number of _GTF commands executed.
While at it, update _GTF execution reporting such that all successful
commands are logged at KERN_DEBUG and rename taskfile_load_raw() to
ata_acpi_run_tf() for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* If _GTF evalution fails, it's pointless to retry. If nothing else
is wrong, just ignore the error.
* After disabling ACPI, return success iff the number of executed _GTF
command equals zero. Otherwise, tell EH to retry. This change
fixes bogus 1 return bug where ata_acpi_on_devcfg() expects the
caller to reload IDENTIFY data and continue but the caller
interprets it as an error.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain implementations, _GTF evaluation depends on preceding _STM
and both can be pretty picky about the configuration. Using _GTM
result cached during controller initialization satisfies the most
neurotic _STM implementation. However, libata evaluates _GTF after
reset during device configuration and the hardware state can be
different from what _GTF expects and can cause evaluation failure.
This patch adds dev->gtf_cache and updates ata_dev_get_GTF() such that
it uses the cached value if available. Cache is cleared with a call
to ata_acpi_clear_gtf().
Because for SATA ACPI nodes _GTF must be evaluated after _SDD which
can't be done till IDENTIFY is complete, _GTF caching from
ata_acpi_on_resume() is used only for IDE ACPI nodes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
_GTM fetches currently configured transfer mode while _STM configures
controller according to _GTM parameter and prepares transfer mode
configuration TFs for _GTF. In many cases _GTM and _STM
implementations are quite brittle and can't cope with configuration
changed by libata.
libata does not depend on ATA ACPI to configure devices. The only
reason libata performs _GTM and _STM are to make _GTF evaluation
succeed and libata also doesn't care about how _GTF TFs configure
transfer mode. It overrides that configuration anyway, so from
libata's POV, it doesn't matter what value is feeded to _STM as long
as evaluation succeeds for _STM and following _GTF.
This patch adds dev->__acpi_init_gtm and store initial _GTM values on
host initialization before modified by reset and mode configuration.
If the field is valid, ata_acpi_init_gtm() returns pointer to the
saved _GTM structure; otherwise, NULL.
This saved value is used for _STM during resume and peek at
BIOS/firmware programmed initial timing for later use. The accessor
is there to make building w/o ACPI easy as dev->__acpi_init doesn't
exist if ACPI is not enabled.
On driver detach, the initial BIOS configuration is restored by
executing _STM with the initial _GTM values such that the next driver
can also use the initial BIOS configured values.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add two hooks - ata_acpi_dissociate() which is called during driver
detach after the whole host is shutdown and ata_acpi_on_disable()
which is called when a device is disabled.
Signed-off-by: Tejun heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_port_detach() calls ata_dev_disable() with host lock held but
ata_dev_disable() should be called from EH context. ata_port_detach()
steals EH context by setting ATA_PFLAG_UNLOADAING and flushing EH.
Drop locking around ata_dev_disable() and note that ata_port_detach()
owns EH context at that point.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* No internal function uses const ata_port. Drop const from @ap.
* Make ata_acpi_stm() copy @stm before using it and change @stm to
const.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Improve the existing boot/load time warnings from sata_mv
for Highpoint RocketRAID 23xx cards, based on new knowledge
about where the BIOS likes to overwrite sectors with metadata.
Harmless to us, but very useful for end users.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Like ST380817AS / 3.42, ST3160023AS / 3.42 times out commands if NCQ
is used. Blacklist it. This is reported by Matheus Izvekov in the
following thread.
http://thread.gmane.org/gmane.linux.ide/24202
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Matheus Izvekov <mizvekov@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
link->eh_info.serror is used to cache SError for controllers which
need it cleared from interrupt handler to clear IRQ. It also should
be cleared after reset just like SError itself.
Make ata_std_postreset() clear link->eh_info.serror too and update
sata_sil such that it doesn't care about bookkeeping the value.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Interestingly, sata_sil raises spurious interrupts if it's coupled
with Sil SATA_PATA bridge. Currently, sata_sil interrupt handler is
strict about spurious interrupts and freezes the port when it occurs.
This patch makes it more forgiving.
* On SATA PHY event interrupt, serror value is checked to see whether
it really is PHYRDY CHG event. If not, SATA PHY event interrupt is
ignored.
* If ATA interrupt occurs while no command is in progress, it's
cleared and ignored.
This fixes bugzilla bug 9505.
http://bugzilla.kernel.org/show_bug.cgi?id=9505
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spurious NCQ completion detection implemented in ahci was incorrect.
On AHCI receving and processing FISes and raising interrupts are not
interlocked and spurious interrupts are expected.
For example, if an interrupt occurs while interrupt handler is running
and the running interrupt handler handles the event the new IRQ
indicated, after IRQ handler finishes, it will be executed again
because IRQ pending bit is set by the new interrupt but there won't be
anything to process.
Please read the following message for more information.
http://article.gmane.org/gmane.linux.ide/26012
This patch...
* Removes all spurious IRQ whining from ahci. Spurious NCQ completion
detection was completely wrong. Spurious D2H Register FIS taught us
that some early drives send spurious D2H Register FIS with I bit set
while NCQ commands are in progress but none of recent drives does
that and even the ones which show such behavior can do NCQ fine.
* Kills all NCQ blacklist entries which were added because of spurious
NCQ completions. I tracked down each commit and verified all
removed ones are actually added because of spurious completions.
WD740ADFD-00NLR1 wasn't deleted but moved upward because the drive
not only had spurious NCQ completions but also is slow on sequential
data transfers if NCQ is enabled.
Maxtor 7V300F0 was added by 0e3dbc01d5
from Alan Cox. I can only find evidences that the drive only had
troubles with spuruious completions by searching the mailing list.
This entry needs to be verified and removed if it doesn't have other
NCQ related problems.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ICH6 R/Ms share PCI ID between piix and ahci modes and we've been
allowing ahci to attach regardless of how BIOS configured it.
However, enabling AHCI mode when the controller is in combined mode
can result in unexpected behavior. Don't attach if the controller is
in combined mode.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bill Nottingham <notting@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Toshiba Tecra M4 to broken suspend list. This is from OSDL
bugzilla bug 7780.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There isn't much point in reporting -EOPNOTSUPP as failure. Also the
message was missing newline.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Don't program UDMA timings when programming PIO or MWDMA modes.
This has also a nice side-effect of fixing regression added by commit
681c80b5d9 ("libata: correct handling of
SRST reset sequences") (->set_piomode method for PIO0 is called before
->cable_detect method which checks UDMA timings to get the cable type).
* Bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Tested-by: "Thomas Lindroth" <thomas.lindroth@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the device IDs of legacy mode of MCP79 AHCI controller to ahci.c
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Highpoint RocketRAID boards using Marvell 7042 chips
overwrite the 9th sector of attached drives at boot time,
when those drives are configured as "Legacy" (the default)
in the HighPoint BIOS.
This kills GRUB, and probably other stuff.
But it all happens *before* Linux is even loaded.
So, for now we'll log a WARNING when such boards are detected,
and advise users to configure BIOS "JBOD" volumes instead,
which don't appear to suffer from this problem.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
We need to run any DMA command with result taskfile requested in ADMA mode
when the port is in ADMA mode, otherwise it may try to use the legacy DMA engine
in ADMA mode which is not allowed. Enforce this with BUG_ON() since data
corruption could potentially result if this happened. Also, fail any attempt to
try and issue NCQ commands with result taskfile requested, since the hardware
doesn't allow this.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_mv: Fix broken Marvell 7042 support.
The Marvell 7042 chip is more or less the same as the 6042 internally,
but sports a PCIe bus. Despite having identical SATA cores, the 7042
does differ from its PCI bus counterparts in placment and layout of
certain bus related registers.
This patch fixes sata_mv to distinguish between the PCI bus registers
of earlier chips, and the PCIe bus registers of the 7042.
Specifically, move the offsets and bit patterns for the
PCI/PCIe interrupt cause/mask registers into the struct mv_host_priv,
as these values differ between the 6xxx and 7xxx series chips.
This fixes the driver to not access reserved PCI addresses,
and prevents the lockups reported in linux-2.6.24 with 7042 boards.
Also add a new PCI ID for the Highpoint 2300 7042-based board
that I'm using for testing this stuff here.
Tested with Marvell 6081 + 7042 chips, on x86 & x86_64.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Fri, 30 Nov 2007 14:34:11 +0200 (EET)
Meelis Roos <mroos@linux.ee> wrote:
> > Can you stick a stack trace in at that point ? That would help diagnose
> > it a great deal quicker.
>
> Finally done - found out hard way that BUG() is too bad and
> dump_st5ack() suits me better.
Thanks. This should fix the real cause, and also allow for port start to
fail politely with -ENODEV.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add more toshiba laptops to broken suspend list. This is from OSDL
bugzilla bug 7780.
tj: re-formatted patch and added description and SOB.
Signed-off-by: Peter Schwenke <peter@bluetoad.com.au>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata: Add more TSST (Samsung/Toshiba) IDE drives with broken
cable detection validation bits.
signed-off-by: Peter Missel (peter.missel@onlinehome.de)
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Protocol and CDB allocation size field are important in determining
what went wrong with ATAPI commands. Report them on failure.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several fixes for the AVR32 PATA driver:
* Updated to use new AVR32 SMC timing API. This removes the need for "magic"
constants in signal timing.
* Removed the ATA_FLAG_PIO_POLLING, the driver should use interrupts.
* Removed .port_disable and .irq_ack as these are no longer needed.
* Improved some comments.
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
None of the drives I have follows what the standard says about
transfer chunk size. Of the four SATA and six PATA ATAPI devices
tested, four ignore transfer chunk size completely and the ones which
honor it don't behave according to the spec when it's odd.
According to the spec, transfer chunk size can be odd if the amount of
data to transfer equals or is smaller than the chunk size and the
device can indicate the same odd number and transfer the whole thing
at one go with a pad byte appended. However, in reality, none of the
drives I have does that. They all indicate and transfer even number
of bytes one byte shorter than the chunk size first; then indicate and
transfer two bytes, which is clearly out of spec.
In addition to unnecessary second PIO data phase, this also creates a
weird problem when combined with SATA controllers which perform PIO
via DMA. Some of these controllers use actualy number of bytes
received to update DMA pointer so chunks which are sized 4n + 2 makes
DMA pointer off by two bytes. This causes data corruption and buffer
overruns.
This patch rounds nbytes up to the nearest even number such that ATAPI
devices don't split data transfer for the last odd byte. This
shouldn't confuse controllers which depend on transfer chunk size as
devices will report the rounded-up number, actually transfer that much
and padding buffer is there to receive them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a card has no IRQ then pass no interrupt handler but allow polled
usage.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hopefully there is a better long term solution but for now lets favour
reliability.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24 unnecessarily used LIBATA_MAX_PRD and ATAPI sg table was short
by one entry which might cause very obscure problems. This patch
updates sg table sizing such that
* One full page is used for PRB + sg table. On 4k page,
this results in 253 sg's.
* Make ATAPI sg block properly sized.
* Make build fail if command block size doesn't equal PAGE_SIZE.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are two bugs in disabled port handling.
* test in PORT_PATA0 is reversed
* ->prereset should return -ENOENT for disabled ports not 0
The first bug makes the PATA channel considered disabled but the
second bug saves the day by returning 0. The net result is that cable
is always left at ATA_CBL_UNKNOWN. This results in false 80c
configuration and thus transfer errors.
This patch fixes both bugs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since writing to two reserved bits ain't much of a housekeeping, I think it's
time we get rid of the custom error handler in this driver. ;-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ICH8 and 9 use two SFF controllers to show 6 SATA ports. The first
controllre hosts the first 4 ports while the second one hosts the last
2. The PCS register of the first controller encompasses the first
four ports or all six ports depending on configuration while PCS of
the second controller controls the last two ports. Using 0xf for the
first controller and 0x3 for the second controller always result in
the correct configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
ICH8M on apple macbook pro occasionally locks up completely during PCS
initialization if ports other than the first one are enabled. Add a
separate controller ID and only enable the first port.
tj: commit description added and patch updated to fit with the
previous controller ID update.
Signed-off-by: Thomas Rohwer <tr@tng.de>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Move piix_pata_mwdma to top, rename ich9_2port_sata to ich8_2port_sata
for consistency and use automatically incremented values instead of
assigning fixed values to ease adding new controller IDs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
With newer kernels HDD in my old laptop is limited to UDMA 33.
With this patch I get UDMA 100 again.
Signed-off-by: Gabriel Craciunescu <nix.or.die@googlemail.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Sebastian Kemper reported that issuing CD/DVD commands under libata is
not fully compatible with ide-scsi. In particular, the
GPCMD_SET_STREAMING was being rejected at the host level in some
instances.
The reason is that libata-scsi insists upon the cmd_len field exactly
matching the SCSI opcode being issued, whereas ide-scsi tolerates
12-byte commands contained within a 16-byte (cmd_len) CDB.
There doesn't seem to be a good reason for us to not be compatible
there, so here is a patch to fix libata-scsi to permit SCSI opcodes so
long as they fit within whatever size CDB is provided.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Per Mark's comments, maybe all ATAPI tape drives need ATA_HORKAGE_STUCK_ERR.
This patch applys ATA_HORKAGE_STUCK_ERR for all ATAPI tape drives.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
After an error condition, some ATAPI tape drives set DRQ=1 together
with ERR=1 when asking the host to transfer the CDB of the next packet
command (i.e. request sense). This patch, a revised version of
Alan/Mark's previous patch, adds ATA_HORKAGE_STUCK_ERR to workaround
the problem by ignoring the ERR bit and proceed sending the CDB.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Satellite U205 has alternate product name where the satellite part is
all capatalized. Add it to the blacklist.
This is reported by Ross Patterson in kernel bugzilla bug #7780.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ross Patterson <me@rpatterson.net>
Experience suggests that the _GTF method may be bad. We currently fail
device revalidation in that case, which seems excessive.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Port / host stop calls used to be made from ata_host_release() which
is called after all hardware resources acquired after host allocation
are released. This is wrong as port and host stop routines often
access the hardware.
Add separate devres for port / host stop which is invoked right after
IRQ is released but with all other hardware resources intact. The
devres is added iff ->host_stop and/or ->port_stop exist.
This problem has been spotted by Mark Lord.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a presentation of true workmanship, pata_ali asserts IRQ
permanantly if the TF status register is read more than once when
there's no device attached to the port.
Avoid waiting polling for !0xff if it's PATA. It's needed only for
some rare SATA devices anyway.
This problem is reported by Luca Tettamanti in bugzilla bug 9298.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Tested-By: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SH boards (old R2D-1 boards) have generally not had working CF
under libata, due to both buswidth issues (handled by Aoi Shinkai
in 43f4b8c757), and buggy interrupt
controllers. For these sorts of boards simply disabling the IRQ and
polling ends up working fine.
This conditionalizes the IRQ resource for pata_platform and lets
platforms that want to use polling mode simply omit the resource
entirely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
By default ata_host_activate() expects a valid IRQ in order to
successfully register the host. This patch enables a special case
for registering polling-only hosts that either don't have IRQs
or have buggy IRQ generation (either in terms of handling or
sensing), which otherwise work fine.
Hosts that want to use polling mode can simply set ATA_FLAG_PIO_POLLING
and pass in an invalid IRQ.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_qstor conversion to new error handling (EH).
Convert sata_qstor to use the newer libata EH mechanisms.
Based on earlier work by Jeff Garzik.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_qstor workaround for spurious interrupts.
The qstor hardware generates spurious interrupts from time to time when
switching in and out of packet mode. These eventually result in the
IRQ being disabled, which kills other devices sharing this IRQ with us.
This workaround isn't perfect, but it's about the best we can do for
this hardware. Spurious interrupts will still happen, but won't be
logged as such, and therefore won't cause the IRQ to be inadvertently
disabled.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_qstor nuke idle state.
We're really only ever in one of two hardware states: packet, or mmio.
Get rid of unnecessary "qs_state_idle" state.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Please warmly welcome the PRO variant of Satellite U200 to the broken
suspend list.
Original patch is from Yann Chachkoff. Patch reformatted and
forwarded by Tejun Heo.
Signed-off-by: Yann Chachkoff <yann.chachkoff@myrealbox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One or two ancient drives predated the cable spec and didn't sent the
valid bits for the field. I had hoped to leave this out of libata as a
piece of historical annoyance but a recent CD drive shows the same bug so
we have to import support for it.
Same concept as Bartlomiej's changes old IDE except that as we have
centralised blacklists we can avoid keeping another private table of stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver used the channel not the device number for deciding where to
load some timing parameters. Also change so that we clear the UDMA field
as the old driver did. Not believed neccessary but does no harm.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
LPM seems to get hung up while disabling DIPM, and after thinking
about this a bit, I don't think we really need to manually disable it
anyway.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's nothing to be gained by configuring downstream links faster
than the upstream link and such configurations cause problems on
certain PMPs. Limit downstream link speed by the upstream link speed.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In sata_set_spd_needed(), if SControl read failed, it returned 0 and
skipped PHY speed configuration. However, if SControl access fails,
it's far more logical to request PHY speed configuration. Reverse the
logic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata EH used to ignore errors not associated with commands when
determining whether speed down is necessary or not. This leads to the
following problems.
* Errors not associated with commands can occur indefinitely without
libata EH taking corrective actions.
* Upstream link errors don't trigger speed down when PMP is attached
to it and commands issued to downstream device trigger errors on the
upstream link.
This patch makes ata_eh_link_autopsy() consider errors not associated
with command for speed down.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reset failure is a critical error. It results in disabling the link
requiring user intervention to re-enable it. Make reset failure
handling more robust such that libata EH doesn't give up too early.
* Temporary glitches during hardreset may lead to classification
failure when there's no softreset available. Retry instead of
giving up.
* Initial softreset or follow up softreset may fail classification.
Move classification error handling block out of followup softreset
block such that both cases are handled and retry instead of giving
up. Also, on the last try, give ATA class a blind shot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clean up and reorganize ata_eh_reset() to ease further changes.
* Cache ARRAY_SIZE(ata_eh_reset_timeouts) in @max_tries.
* Cache link->flags in @lflags.
* Move failure handling block to the end of the function and unnest
both success and failure handling blocks.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As jiffies changes asynchronously, it needs to be cached if unchanging
timestamp is needed. The code in ata_eh_reset() intended to do that
with @now but never actually did it. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commands sent to ATAPI tape drives via the SCSI generic (sg) driver are
limited in the amount of data that they can transfer by the max_sectors
value. The max_sectors value is currently calculated according to the
command set for disk drives, which doesn't apply to tape drives. The
default max_sectors value of 256 limits ATAPI tape drive commands to
128 KB. This patch against 2.6.24-rc1 increases the max_sectors value
for tape drives to 65535, which permits tape drive commands to transfer
just under 32 MB.
Tested with a SuperMicro PDSME motherboard, AHCI, and a Sony SDX-570V
SATA tape drive.
Note that some of the chipset drivers also set their own max_sectors
value, which may override the value set in libata-core. I don't have
any of these chipsets to test, so I didn't go messing with them. Also,
ATAPI devices other than tape drives may benefit from similar changes,
but I have only tape drives and disk drives to test.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original workaround for the Promise ASIC PRD bug
contained an endianess bug which I failed to detect:
the adjustment of the last PRD entry's length field
applied host arithmetic to little-endian data, which
is incorrect on big-endian machines.
We have the length available in host-endian format, so
do the adjustment on host-endian data and then convert
and store it in the PRD entry's little-endian data field.
Thanks to an anonymous reviewer for detecting this bug.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/ata/libata-core.c:768: warning: 'ata_lpm_enable' defined but not used
drivers/ata/libata-core.c:784: warning: 'ata_lpm_disable' defined but not used
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded on-stack copy of FIS
in sata_fsl_cache_taskfile_from_d2h_fis().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCRs in the driver map to the standard values found in include/linux/ata.h,
so no need for individual scr_read/scr_write case statements duplicating
the natural value.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_QCFLAG_QUIET which indicates that there's no need to
report if the command fails with AC_ERR_DEV and set it for passthrough
commands.
Combined with previous changes, this now makes device errors for all
direct commands reported directly to the issuer without going through
EH actions and reporting.
Note that EH is still invoked after non-IO device errors to determine
the nature of the error and resume command execution (some controller
requires special care after error to continue). It just performs
default maintenance after error, examines what's going on, realizes
that it's none of its business and reports the command failure without
logging any error messages.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
libata EH always revalidated device and retried failed command after
error except for ATAPI CCs. This is unnecessary and hinders with
users issuing direct commands. This patch makes the following
changes.
* Make sata_sil24 not request ATA_EH_REVALIDATE on device errors.
sil24 is the only driver which does this. All others let libata EH
core code decide.
* Don't request revalidation after device error of non-IO command.
Revalidation doesn't really help anybody. As ATA_EH_REVALIDATE
isn't set by default, there's no reason to clear it after sense data
is read. Kill ATA_EH_REVALIDATE clearing code while at it.
* Don't retry non-IO command after device error. Device has rejected
the command. There's no point in retrying.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_QCFLAG_IO is used to mark commands which are used to perform
regluar IO transfers via block layer. These commands are assumed to
be valid and taken more seriously during error handling. Cache flush
is used by regular IO path and necessary for data integrity. Mark it
with ATA_QCFLAG_IO.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Second-generation Promise SATA controllers have an ASIC bug
which can trigger if the last PRD entry is larger than 164 bytes,
resulting in intermittent errors and possible data corruption.
Work around this by replacing calls to ata_qc_prep() with a
private version that fills the PRD, checks the size of the
last entry, and if necessary splits it to avoid the bug.
Also reduce sg_tablesize by 1 to accommodate the new entry.
Tested on the second-generation SATA300 TX4 and SATA300 TX2plus,
and the first-generation PDC20378.
Thanks to Alexander Sabourenkov for verifying the bug by
studying the vendor driver, and for writing the initial patch
upon which this one is based.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
Changes since previous version:
* use new PDC_MAX_PRD constant to initialise sg_tablesize
drivers/ata/sata_promise.c | 87 ++++++++++++++++++++++++++++++++++++++++++---
1 files changed, 83 insertions(+), 4 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'alpm' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: add hw link power management support
[libata] Link power management infrastructure
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] AHCI: fix newly introduced host-reset bug
[libata] sata_nv: fix SWNCQ enabling
libata: add MAXTOR 7V300F0/VA111900 to NCQ blacklist
libata: no need to speed down if already at PIO0
libata: relocate forcing PIO0 on reset
pata_ns87415: define SUPERIO_IDE_MAX_RETRIES
[libata] Address some checkpatch-spotted issues
[libata] fix 'if(' and similar areas that lack whitespace
libata: implement ata_wait_after_reset()
libata: track SLEEP state and issue SRST to wake it up
libata: relocate and fix post-command processing
This patch will set the correct bits to turn on Aggressive
Link Power Management (ALPM) for the ahci driver. This
will cause the controller and disk to negotiate a lower
power state for the link when there is no activity (see
the AHCI 1.x spec for details). This feature is mutually
exclusive with Hot Plug, so when ALPM is enabled, Hot Plug
is disabled. ALPM will be enabled by default, but it is
settable via the scsi host syfs interface. Possible
settings for this feature are:
Setting Effect
----------------------------------------------------------
min_power ALPM is enabled, and link set to enter
lowest power state (SLUMBER) when idle
Hot plug not allowed.
max_performance ALPM is disabled, Hot Plug is allowed
medium_power ALPM is enabled, and link set to enter
second lowest power state (PARTIAL) when
idle. Hot plug not allowed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Device Initiated Power Management, which is defined
in SATA 2.5 can be enabled for disks which support it.
This patch enables DIPM when the user sets the link
power management policy to "min_power".
Additionally, libata drivers can define a function
(enable_pm) that will perform hardware specific actions to
enable whatever power management policy the user set up
for Host Initiated Power management (HIPM).
This power management policy will be activated after all
disks have been enumerated and intialized. Drivers should
also define disable_pm, which will turn off link power
management, but not change link power management policy.
Documentation/scsi/link_power_management_policy.txt has additional
information.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The recent fix to host reset introduced a problem, whereby AHCI-enable
bit would be cleared upon reset, if it was not asserted prior to reset.
Unconditionally enable AHCI-enable bit.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
MAXTOR 7V300F0/VA111900 does spurious NCQ completions. Add it to
blacklist. This problem is reported by Carsten Otto.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Carsten Otto <c-otto@gmx.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After reset, transfer mode is always PIO0 regardless of
dev->xfer_mask. Check dev->pio_mode before trying to slow down after
configuration failure. This prevents bogus speed down before device
is actually configured.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Forcing PIO0 on reset was done inside ata_bus_softreset(), which is a
bit out of place as it should be applied to all resets - hard, soft
and implementation which don't use ata_bus_softreset(). Relocate it
such that...
* For new EH, it's done in ata_eh_reset() before calling prereset.
* For old EH, it's done before calling ap->ops->phy_reset() in
ata_bus_probe().
This makes PIO0 forced after all resets. Another difference is that
reset itself is done after PIO0 is forced.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code copied from drivers/ide/pci/ns87415.c uses this, so copy the
definition from there as well.
Fixes the following build error:
CC [M] drivers/ata/pata_ns87415.o
drivers/ata/pata_ns87415.c: In function ‘ns87560_read_buggy’:
drivers/ata/pata_ns87415.c:228: error: ‘SUPERIO_IDE_MAX_RETRIES’ undeclared (first use in this function)
drivers/ata/pata_ns87415.c:228: error: (Each undeclared identifier is reported only once
drivers/ata/pata_ns87415.c:228: error: for each function it appears in.)
Signed-off-by: Frank Lichtenheld <frank@lichtenheld.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On certain device/controller combination, 0xff status is asserted
after reset and doesn't get cleared during 150ms post-reset wait. As
0xff status is interpreted as no device (for good reasons), this can
lead to misdetection on such cases.
This patch implements ata_wait_after_reset() which replaces the 150ms
sleep and waits upto ATA_TMOUT_FF_WAIT if status is 0xff.
ATA_TMOUT_FF_WAIT is currently 800ms which is enough for
HHD424020F7SV00 to get detected but not enough for Quantum GoVault
drive which is known to take upto 2s.
Without parallel probing, spending 2s on 0xff port would incur too
much delay on ata_piix's which use 0xff to indicate empty port and
doesn't have SCR register, so GoVault needs to wait till parallel
probing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA devices in SLEEP mode don't respond to any commands. SRST is
necessary to wake it up. Till now, when a command is issued to a
device in SLEEP mode, the command times out, which makes EH reset the
device and retry the command after that, causing a long delay.
This patch makes libata track SLEEP state and issue SRST automatically
if a command is about to be issued to a device in SLEEP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Bruce Allen <ballen@gravity.phys.uwm.edu>
Cc: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some commands need post-processing after successful completion. This
was done in ata_scsi_qc_complete() till now but this has the following
problems.
* Post-command processing gets executed when qc is completed from EH.
Some qc's are retried from EH with zero err_mask and thus triggers
unnecessary/incorrect post-command processing.
* Command post processing doesn't belong to SAT layer.
* Link-wide revalidation was scheduled where device revalidation
suffices.
This patch moves post-command processing to success completion path of
ata_qc_complete() which is travelled iff the command is going to be
completed without passing through EH and updates post-command
processing such that device-specific action is used. While at it,
restructure code a bit for readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After turning on DEBUG_SG I hit a fail:
kernel BUG at include/linux/scatterlist.h:50!
ata_qc_issue
ata_scsi_translate
ipr_queuecommand
scsi_dispatch_cmd
scsi_request_fn
elv_insert
blk_execute_rq_nowait
blk_execute_rq
sg_io
scsi_cmd_ioctl
cdrom_ioctl
sr_block_ioctl
blkdev_driver_ioctl
blkdev_ioctl
block_ioctl
do_ioctl
vfs_ioctl
sys_ioctl
sg_ioctl_trans
It looks like ata_sg_setup is working on an uninitialised sg table. Call
sg_init_table to initialise it before use.
Signed-off-by: Anton Blanchard <anton@samba.org>
Note: this patch will fix it, but you could also get away with just
doing the sg_init_table() once at qc creation time.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
* 'sg' of git://git.kernel.dk/linux-2.6-block:
fix sg_phys to use dma_addr_t
ub: add sg_init_table for sense and read capacity commands
x86: pci-gart fix
blackfin: fix sg fallout
xtensa: dma-mapping.h is using linux/scatterlist.h functions, so include it
SG: audit of drivers that use blk_rq_map_sg()
arch/um/drivers/ubd_kern.c: fix a building error
SG: Change sg_set_page() to take length and offset argument
AVR32: Fix sg_page breakage
mmc: sg fallout
m68k: sg fallout
More SG build fixes
sg: add missing sg_init_table calls to zfcp
SG build fix
I guess Windows didn't care about the command so neither did they
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
P5W-DH Deluxe has ICH9 which doesn't have PMP support but SIMG 4726
hardwired to the second port of AHCI controller at PCI device 1f.2.
The 4726 doesn't work as PMP but as a storage processor which can do
hardware RAID on downstream ports.
When no device is attached to the downstream port of the 4726, pseudo
ATA device for configuration appears. Unfortunately, ATA emulation on
the device is very lousy and causes long hang during boot.
This patch implements workaround for the board. If the mainboard is
P5W-DH Deluxe (matched using DMI), only hardreset is used on the
second port of AHCI controller @ 1f.2 and the hardreset doesn't depend
on receiving the first FIS and just proceed to IDENTIFY.
This workaround fixes bugzilla #8923.
http://bugzilla.kernel.org/show_bug.cgi?id=8923
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Local variable @action usage in ata_eh_reset() is a bit confusing.
It's used only to cache ehc->i.action to test reset masks after
clearing it; however, due to the generic name "action", it's easy to
misinterpret the local variable as containing the selected reset
method later. Also, the reason for caching the original value is easy
to miss.
This patch renames @action to @tmp_action and make it buffer newly
selected value instead to improve readability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Another one doing spurious NCQ completions. Blacklist it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Did a complete audit of these and found we have another error case.
ata_bus_softreset calls ata_check_status which means that it tries to do
an ioread8 on the port blindly and check versus 0xFF for an error.
It should of course be using the ap->ops method for this via chk_status,
and this bug causes a wrog status call on the NS87415 at least.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tackle the relatively sane complaints of checkpatch --file.
The vast majority is indentation and whitespace changes, the rest are
* #include fixes
* printk KERN_xxx prefix addition
* BSS/initializer cleanups
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/bunk/trivial: (74 commits)
fix do_sys_open() prototype
sysfs: trivial: fix sysfs_create_file kerneldoc spelling mistake
Documentation: Fix typo in SubmitChecklist.
Typo: depricated -> deprecated
Add missing profile=kvm option to Documentation/kernel-parameters.txt
fix typo about TBI in e1000 comment
proc.txt: Add /proc/stat field
small documentation fixes
Fix compiler warning in smount example program from sharedsubtree.txt
docs/sysfs: add missing word to sysfs attribute explanation
documentation/ext3: grammar fixes
Documentation/java.txt: typo and grammar fixes
Documentation/filesystems/vfs.txt: typo fix
include/asm-*/system.h: remove unused set_rmb(), set_wmb() macros
trivial copy_data_pages() tidy up
Fix typo in arch/x86/kernel/tsc_32.c
file link fix for Pegasus USB net driver help
remove unused return within void return function
Typo fixes retrun -> return
x86 hpet.h: remove broken links
...
sata_sis has the same restrictions as other SFF controllers, and so must
use LIBATA_MAX_PRD to denote that SCSI may only fill ATA_MAX_PRD/2
entries, due to our need to handle IOMMU merging.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
SCR read for controllers which uses PCI configuration space for SCR
access got broken while adding @val argument to SCR accessors. Fix
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix libata kernel-doc parameter name.
Warning(linux-2.6.23-git13//drivers/ata/libata-core.c:1415): No description found for parameter 'sgl'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the various misspellings of "system", controller", "interrupt" and
"[un]necessary".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[libata] kill ata_sg_is_last()
Update libata driver for bf548 atapi controller against the 2.6.24 tree.
libata-sff: Correct use of check_status()
drivers/ata: add support to Freescale 3.0Gbps SATA Controller
pata_acpi: fix build breakage if !CONFIG_PM
Get rid of sparse related warnings from places that use integer as NULL
pointer.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Andi Kleen <ak@suse.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Ian Kent <raven@themaw.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Short term, this works around a bug introduced by early sg-chaining
work.
Long term, removing this function eliminates a branch from a hot
path loop in each scatter/gather table build. Also, as this code
demonstrates, we don't need to _track_ the end of the s/g list, as
long as we mark it in some way. And doing so programatically is nice.
So its a useful cleanup, regardless of its short term effects.
Based conceptually on a quick patch by Jens Axboe.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ata_check_status() does an SFF compliant check
ata_chk_status() does a generic call to ap->ops->check_status (usually
ata_check_status)
libata-sff uses the wrong one. Hardly suprising given the naming here,
which ought to get fixed to ata_sff_check_status() perhaps ?
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for Freescale 3.0Gbps SATA Controller supporting
Native Command Queueing(NCQ), device hotplug, and ATAPI. This controller
can be found on MPC8315 and MPC8378.
Signed-off-by: Ashish Kalra <ashish.kalra@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are configurations where CONFIG_ACPI but !CONFIG_PM. In this
case, pata_acpi can be selected but won't build. Fix it.
Reported by Avuton Olrich.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Avuton Olrich <avuton@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
LIBATA_MAX_PRD is the maximum number of DMA scatter/gather elements
permitted by the HBA's DMA engine. It's properly set to
q->max_hw_segments via the sg_tablesize parameter.
libata shouldn't call blk_queue_max_phys_segments. Now LIBATA_MAX_PRD
is equal to SCSI_MAX_PHYS_SEGMENTS by default (both is 128), so
everything is fine. But if they are changed, some code (like the scsi
mid layer, sg chaining, etc) might not work properly.
(Addition from Jens) The basic issue is that the physical segment
setting is purely a driver issue. And since SCSI is managing the sglist,
libata has no business changing the setting. All libata should care
about is the hw segment setting.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts libata to using the sg helpers for looking up sg
elements, instead of doing it manually.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix libata docbook warnings.
Warning(linux-2.6.23-git8//drivers/ata/libata-scsi.c:3251): No description found for parameter 'dev'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The strn_pattern_cmp routine does not handle a blank name parameter
properly. The only patterns which should match a blank name are "*"
and an explicit "". If the function is passed a blank name in current
code, it will always match against the patt parameter. The bug manifests
itself as the device with the empty model name always matching the first
device in the DMA blacklist, forcing it to revert to PIO mode.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds a port map for ICH9 and ICH8 SATA controllers that have only 2 ports available in that mode.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a driver for the ATA controller on the Geode CS5536 companion
chip. The PCI device ID for this device was previously claimed by
pata_amd.c but the PIO timings were not correct. This driver also
works around a bug in some BIOSes that handle unaligned access to the
PCI config registers poorly. Finally, the driver allows fallback to
using MSR registers for configuration on BIOSes that are truly
broken.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After commands which can change device configuration, EH is scheduled
to revalidate and reconfigure the device. Host link was incorrectly
used unconditionally when scheduling EH action. This resulted in
bogus revalidation request and mismatched configuration between device
and driver. Fix it.
This bug was reported by Igor Durdanovic.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Igor Durdanovic <idurdanovic@comcast.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the Software NCQ support to sata_nv.c for MCP51/MCP55/MCP61 SATA
controller. NCQ function is disable by default, you can enable it
with 'swncq=1'. NCQ will be turned off if the drive is Maxtor on
MCP51 or MCP55 rev 0xa2 platform.
[akpm@linux-foundation.org: build fix]
Signed-off-by: Kuan Luo <kluo@nvidia.com>
Signed-off-by: Peer Chen <pchen@nvidia.com>
Cc: Zoltan Boszormenyi <zboszor@dunaweb.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This patch adds MMIO support to the pata_sil680 for taskfile IOs,
based on what the old siimage does.
I haven't bothered changing the chip setup stuff from PCI config
cycles to MMIO though (siimage does it), I don't think it matters,
I've only adapted it to use MMIO for taskfile accesses.
I've tested it on a Cell blade and it seems to work fine.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* remove pointless pci_dev_to_dev() wrapper. Just directly reference
the embedded struct device like everyone else does.
* pata_cs5520: delete cs5520_remove_one(), it was a duplicate of
ata_pci_remove_one()
* linux/libata.h: don't bother including linux/pci.h, we don't need it.
Simply declare 'struct pci_dev' and assume interested parties will
include the header, as they should be doing anyway.
* linux/libata.h: consolidate all CONFIG_PCI declarations into a
single location in the header.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
PMP registers used to be accessed with dedicated accessors ->pmp_read
and ->pmp_write. During reset, those callbacks are called with the
port frozen so they should be able to run without depending on
interrupt delivery. To achieve this, they were implemented polling.
However, as resetting the host port makes the PMP to isolate fan-out
ports until SError.X is cleared, resetting fan-out ports while port is
frozen doesn't buy much additional safety.
This patch updates libata PMP support such that PMP registers are
accessed using regular ata_exec_internal() mechanism and kills
->pmp_read/write() callbacks. The following changes are made.
* PMP access helpers - sata_pmp_read_init_tf(), sata_pmp_read_val(),
sata_pmp_write_init_tf() are folded into sata_pmp_read/write() which
are now standalone PMP register access functions.
* sata_pmp_read/write() returns err_mask instead of rc. This is
consistent with other functions which issue internal commands and
allows more detailed error reporting.
* ahci interrupt handler is modified to ignore BAD_PMP and
spurious/illegal completion IRQs while reset is in progress. These
conditions are expected during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_PFLAG_RESETTING. This flag is set while reset is in
progress. It's set before prereset is called and cleared after reset
fails or postreset is finished.
This flag itself doesn't have any function. It will be used by LLDs
to tell whether reset is in progress if it needs to behave differently
during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @timeout argument to ata_exec_internal[_sg](). If 0, default
timeout ata_probe_timeout is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Asynchronous notification on ICH9 didn't work because it didn't write
AN FIS into the RX area - it only updates SNotification. Also,
snooping SDB_FIS RX area is racy against further SDB FIS receptions.
Let sata_async_notification() determine using SNTF if it's available
and snoop RX area iff SNTF isn't available
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Now that we have pp->intr_mask, move PORT_IRQ_BAD_PMP enabling to
ahci_pmp_attach/detach() where it belongs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci had problems with NCQ over PMP and NCQ used to be disabled while
PMP was attached. After fixing the problem, the temporary NCQ
disabling code wasn't removed completely. Kill the remaining piece.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Tasks in uninterruptible sleep might be woken up by unrelated events
and should check whether the condition it was waiting for has actually
triggered. Wrap schedule_timeout_uninterruptible() in loop to achieve
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_EHI_NO_AUTOPSY and ATA_EHI_QUIET are used during initial probing
to skip exception analysis and reporting. Usually, there's nothing to
report but on some allowed but rare corner cases (e.g. phy status
changed interrupt when IRQ is enabled on frozen port - this happens if
IRQ pending status isn't cleared in the IRQ router or controller)
exception messages get printed.
Skip reporting if ATA_EHI_QUIET is set.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ehi description field is used to carry LLD specific controller
description. Sometimes, it's used without clearing before and LLD
description gets printed with exception information one more time.
Clear after printing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PATA part of all current JMB controllers behave the same way and
JMicron confirms that all future ones will stay compatible. Drop
device matching and match only vendor and class.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Ethan Hsiao <ethanhsiao@jmicron.com>
Cc: Justin Tsai <justin@jmicron.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On a cable there may be
eighty wires or perhaps forty
and we learn about its type
In the world of ACPI
So we call the GTM
And we find the the timing rate
And we look through it to see
If eighty wire it must be
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
And the drivers last you see
Picking up unknown pci ids
and the code begins to work
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
[Full speed ahead, Mr Hacker, full speed ahead]
Full speed over here sir!
Checking Cable, checking cable
Aye aye, 80 wire,
Heaven heaven]
If we use ACPI (ACPI)
Every box (every box) has all we need (has all we need)
Cable type (cable type) and mode timing (mode timing)
In our ATA (in our ATA) subroutines (subroutines, ha ha)
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
Timing lives in ACPI routines
ACPI routines, ACPI routines
Timing lives in ACPI routines
ACPI routes ACPI routines
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Talk to the dark side our driver has to, yes. Much misleading is the
data. Store it in a structure we do so that it may be parsed.
Signed-off-by: Alan Cox <alan@redhat.com>
--
Whats small, old and shouts phrases out of order across mountains ?
Yodla..
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HDT722516DLA380 does spurious completion of NCQ commands. Blacklist
it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Seagate Barracuda ST380817AS has troubles with NCQ. For example,
unpacking a tarball on an XFS filesystem gives this:
ata1.00: exception Emask 0x0 SAct 0x1 SErr 0x0 action 0x2 frozen
ata1.00: cmd 61/40:00:29:a3:98/00:00:00:00:00/40 tag 0 cdb 0x0 data 32768 out
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x4 (timeout)
More info here:
http://lkml.org/lkml/2007/1/21/76
Blacklist it!
Signed-off-by: Paolo Ornati <ornati@fastwebnet.it>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some controller variants snoop the ATAPI length value for Packet
transfers to do state machine and FIFO management. Thus we want to
set it properly, even for cases where it is otherwise meaningless.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Correct handling of SRST reset sequences. After an SRST it is undefined
whether the drive has gone back to PIO0. In order to talk safely we should
talk slowly and carefully until we know.
Thus when we do the reset if the controller has a pio setup method we call it
to flip back to PIO 0 and a known state. After the reset completes the
identify will then be done at the safe speed and the drive/controller will
pick suitable faster modes and reconfigure the controller to these timings.
As a side effect it means we force the controller to PIO 0 as we bring it up
which fixes funnies on a few systems where the BIOS firmware leaves us in an
interesting choice of modes, or embedded boxes with no firmware which come up
in random states.
For smart controllers there is nothing to do - they know about this
internally.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Modern laptops with hotswap bays still tend to utilise a PATA interface
on a SATA bridge, generally with the host controller in some legacy
emulation mode rather than AHCI. This means that the existing hotplug
code in libata is unable to work. The ACPI specification states that
these devices can send notifications when hotswapped, which avoids the
need to obtain notification from the controller. This patch uses the
existing libata-acpi code and simply registers a notification in order
to trigger a rescan whenever the firmware signals an event.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is useful when debugging, handling problem systems, or for
distributions just to get the system installed so it can be sorted
out later.
This is a bit smarter than the old IDE one and lets you do
libata.dma=0 Disable all PATA DMA like old IDE
libata.dma=1 Disk DMA only
libata.dma=2 ATAPI DMA only
libata.dma=4 CF DMA only
(or combinations thereof - 0,1,3 being the useful ones I suspect)
(I've split CF as it seems to be a seperate case of pain and suffering
different to the others and caused by assorted PIO wired adapters etc)
Signed-off-by: Alan Cox <alan@redhat.com>
[edited to work on SATA too, changing name from 'pata_dma' to 'dma']
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds human-readable decoding of the ATA status and error registers
(similar to what drivers/ide does) as well as the SATA Serror register
to libata error handling output. This prevents the need to pore
through standards documents to figure out the meaning of the bits
in these registers when looking at error reports. Some bits that
drivers/ide decoded are not decoded here, since the bits are either
command-dependent or obsolete, and properly parsing them would add
too much complexity.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
[edited slightly to make output a bit more symmetric]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Of course some controllers lie about PMP support. Black list them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Private pi.flags area is full and we need more private flags. Move
host private flags over to pi.private_data. During initialization,
these flags are copied to hpriv->flags.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement AHCI PMP support. ahci only supports command based
switching. Also, for some reason, NCQ over PMP doesn't work now.
Other than that, everything works.
Tested on ICH9R, JMB360/363 + SIMG3726, 4726 and 5744.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Forrest Zhao <forrest.zhao@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As DEV_RST (hardreset) sometimes fail to recover the controller
(especially after PMP DMA CS errata). In such cases, perform PORT_RST
prior to DEV_RST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement PMP support. sil24 supports full FIS-switching. However,
it has a PMP DMA CS errata which requires port-wide resetting if
commands are outstanding to three or more devices when an error occurs
on one of them.
ATAPI commands often result in CHECK SENSE and it's crucial to not
reset them before fetching sense data. Unfortunately, ATAPI CHECK
SENSE causes a lot of problem if command is outstanding to any other
device usually resulting in port-wide reset. So, sata_sil24
implements sil24_qc_defer() which guarantees ATAPI command is run by
itself.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Extend ata_acpi_associate_sata_port() such that it can handle PMP and
call it when PMP is attached and detached.
Build breakage when !CONFIG_ATA_ACPI was spotted and fixed by Petr
Vandrovec.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hook PMP support into libata and enable it. Connect SCR and probing
functions, and update ata_dev_classify() to detect PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement Port Multiplier support. To support PMP, a LLDD has to
supply ops->pmp_read() and pmp_write(). If non-null, ->pmp_attach and
->pmp_detach are called on PMP attach and detach, respectively.
->pmp_read/write() can be called while the port is frozen, so they
must be implemented by polling. This patch supplies several helpers
to ease ->pmp_read/write() implementation.
Also, irq_handler and error_handler must be PMP aware. Most of PMP
aware EH can be done by calling ata_pmp_do_eh() with appropriate
methods. PMP EH uses separate set of reset methods and this patch
implements standard prereset, hardreset and postreset methods.
This patch only implements PMP support. The next patch will integrate
PMP into the reset of libata and thus enable PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PMP always requires SRST to be enabled. Also, hardreset reports
classification code from the first device when PMP is attached, not
from the PMP. Update ata_eh_reset() such that followup softreset is
performed if the controller is PMP capable and the host link is being
reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Restore the support for handling drives that report one sector too many
(ie SCSI not ATA style). This worked before the HPA update but was
removed in that process.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Blacklist HITACHI HDS7250SASUN500G and HITACHI HDS7225SBSUN250G
drives using wildcard matching.
Signed-off-by David Milburn <dmilburn@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* The firmware version of ST3160812AS is "3.ADJ" no "3.AD".
* Add several entries from various sources.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I've been doing an audit of this driver to try and find out why we have
problems with some Clevo boxes that use it. Didn't get anywhere other
than to discover all the bug reporters I have use vmware, which may or
may not be chance.
In the process however I did find out our MWDMA2 performance was a bit
low and code review showed the MWDMA0/2 timings are reversed due to a
thinko in the table ordering
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AHCI spec says host-reset bit may only be set when the ahci-enable bit
is also set.
Noticed by Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Little fixlets, that the build started erroring / warning about:
drivers/ata/pata_scc.c: In function 'scc_bmdma_status':
drivers/ata/pata_scc.c:734: error: structure has no member named 'active_tag'
drivers/ata/pata_scc.c: In function 'scc_pata_prereset':
drivers/ata/pata_scc.c:866: warning: passing arg 1 of 'ata_std_prereset' from incompatible pointer type
drivers/ata/pata_scc.c: In function 'scc_error_handler':
drivers/ata/pata_scc.c:908: warning: passing arg 2 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:908: warning: passing arg 3 of 'ata_bmdma_drive_eh' from incompatible pointer type
drivers/ata/pata_scc.c:908: warning: passing arg 5 of 'ata_bmdma_drive_eh' from incompatible pointer type
make[2]: *** [drivers/ata/pata_scc.o] Error 1
Signed-off-by: Satyam Sharma <satyam@infradead.org>
Cc: Alan Cox <alan@redhat.com>
Cc: Mel Gorman <mel@skynet.ie>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The SATA_PATA_SHARING register doesn't have anything to do with the
SATA part of the controller. It indicates whether an extern SATA PHY
is attached to the PATA part of the controller and if so how it is
wired. As the PATA part is driven by pata_via, sata_via has no reason
to care about that. Also, pata_via should work fine under all
configurations.
This patch removes unnecessary attach failures. It seems recent via
chipsets are defaulting to different values or are actually connected
to SATA PHY triggering this more often.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In ata_set_max_sectors(), the highest nibble in LBA28 mode was
missing. This made drives sized between 8G and 128G with HPA turned
on to be resized to under 8G. Fix it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
AN serves multiple purposes. For ATAPI, it's used for media change
notification. For PMP, for downstream PHY status change notification.
Implement sata_async_notification() which demultiplexes AN.
To avoid unnecessary port events, ATAPI AN is not enabled if PMP is
attached but SNTF is not available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some pseudo devices fail PM commands unnecessarily aborting system
suspend. Implement ATA_HORKAGE_SKIP_PM which makes libata skip PM
commands for these devices.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PMP itself becomes inaccessible while trying to link a downstream
link, spending time to recover the downstream link doesn't make any
sense. Make EH skip retry and fail fast if -ERESTART is received.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ATA_LFLAG_DISABLED. The flag indicates the link is disabled
due to EH recovery failure. While a link is disabled, no EH action is
taken on the link and suspend/resume become noop too.
This will be used by PMP links to manage failed links.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some PMP links are connected to internal pseudo devices which may come
and go depending on situation. There's no reason to try hard to
recover them. ATA_LFLAG_NO_RETRY tells EH to not retry if the device
attached to the link fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some links on some PMPs locks up on SRST and/or report incorrect
device signature. Implement ATA_LFLAG_NO_SRST, ASSUME_ATA and
ASSUME_SEMB to handle these quirky links. NO_SRST makes EH avoid
SRST. ASSUME_ATA and SEMB forces class code to ATA and SEMB_UNSUP
respectively. Note that SEMB isn't currently supported yet so the
_UNSUP variant is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ap->nr_active_links (the number of links with active qcs),
ap->excl_link (pointer to link which can be used by ->qc_defer and is
cleared when a qc with ATA_QCFLAG_CLEAR_EXCL completes), and
ata_link_active().
These can be used by ->qc_defer() to implement proper command
exclusion. This set of helpers seem enough for both sil24 (ATAPI
exclusion needed) and cmd-switching PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Controllers which support PMP have various restrictions on which
combinations of commands are allowed to what number of devices
concurrently. This patch implements ops->qc_defer() which determines
whether a qc can be issued at the moment or should be deferred.
If the function returns ATA_DEFER_LINK, the qc will be deferred until
a qc completes on the link. If ATA_DEFER_PORT, until a qc completes
on any link. The defer conditions are advisory and in general
ATA_DEFER_LINK can be considered as lower priority deferring than
ATA_DEFER_PORT.
ops->qc_defer() replaces fixed ata_scmd_need_defer(). For standard
NCQ/non-NCQ exclusion, ata_std_qc_defer() is implemented. ahci and
sata_sil24 are converted to use ata_std_qc_defer().
ops->qc_defer() is heavier than the original mechanism because full qc
is prepped before determining to defer it, but various information is
needed to determine defer conditinos and fully translating a qc is the
only way to supply such information in generic manner.
IMHO, this shouldn't cause any noticeable performance issues as
* for most cases deferring occurs rarely (except for NCQ-aware
cmd-switching PMP)
* translation itself isn't that expensive
* once deferred the command won't be repeated until another command
completes which usually is a very long time cpu-wise.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make a number of functions from libata-core.c and libata-eh.c global
to libata (drivers/ata/libata.h). These will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consider newly found class code while revalidating. PMP resetting
always results in valid class code and issuing PMP commands to
ATA/ATAPI device isn't very attractive. Add @new_class to
ata_dev_revalidate() and check class code for revalidation.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update AN support in preparation of PMP support.
* s/ata_id_has_AN/ata_id_has_atapi_AN/
* add AN enabled reporting during configuration
* add err_mask to AN configuration failure reporting
* update LOCKING comment for ata_scsi_media_change_notify()
* check whether ATA dev is attached to SCSI dev ata_scsi_media_change_notify()
* set ATA_FLAG_AN in ahci and sata_sil24
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Kriten Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Clear ARRE, we don't do auto-reallocation on reads, just on writes.
Also, hardcode the size of the array using RW_RECOVERY_MPAGE_LEN,
following the style of the surrounding code.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* SAT specifies that FORMAT UNIT should be translated into a series
of READ and WRITE commands that zero the ATA device. That is far too
cumbersome to bother with.
Since we don't actually format the device, the old behavior of
always returning success was inaccurate. Change FORMAT UNIT from
returning success immediately (old behavior) to always returning
an error (new behavior).
* Add some comments around SYNCHRONIZE CACHE
* Shuffle scsi command code around a bit, so that things are close
to alphabetic order.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A few pedantic apps care about missing or lame "mandatory" SCSI
commands, so
REQUEST SENSE -- as we autosense, R.S. just returns zeroes
SEND DIAGNOSTIC -- our default (no-op) self-test succeeds, all
other requests for testing fail.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Certain device which reports diagnostic failure also reports invalid
device signature. Assume ATA_DEV_ATA on diagnostic failure if reset
indicates device presence.
This is fix for bugzilla bug 8784.
http://bugzilla.kernel.org/show_bug.cgi?id=8784
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Edward Amsden <amsden_linux@earthlink.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_dev_try_classify() take a pointer to ata_device instead of
ata_port/port_number combination for consistency and add @present
argument. @present indicates whether the device seems present during
reset. It's the result of TF access during softreset and link
onlineness during hardreset. @present will be used to improve
diagnostic failure handling.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Reimplement port_map handling such that
1. Non-zero PORTS_IMPL value is always examined and used if consistent
with cap.n_ports.
2. When PI and cat.n_ports are inconsistent, honor cap.n_ports and
force port_map to be ((1 << cap.n_ports) - 1).
3. There were two separate places dealing with port_map. Unify them
to one.
As all newer ahci chips seem to get PI correct and older ones usually
have zero PI. Controllers with holes in PI are very unlikely to screw
up PI, so #2 makes more sense than following inconsistent PI.
Without this change, not setting ATA_FLAG_HONOR_PI when it's needed
results in weird detection failure. This changed logic should be able
to handle all known cases correctly automatically.
Verified on ICH6 (reports 0 PI), ICH8 (with holes in port_map), ICH9,
JMB360 and JMB363.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reimplement ata_hpa_resize() such that...
* All HPA related decisions are made inside ata_hpa_resize() proper.
ata_hpa_resize() returns 0 if configuration can proceed, -errno if
device needs to be reset and reconfigured.
* All errors are handled properly. If HPA unlocking isn't requested,
HPA handling is disabled automatically to avoid unnecessary device
detection failure.
* Messages are trimmed. HPA detection message is printed only during
initial configuration. HPA unlocked message is printed only during
initial configuration or unlocking results in different size.
* Instead of using sectors returned in TF of SET_MAX, re-read IDENTIFY
data as that's the value the device is going to use.
* It's called early during ata_dev_configure() as IDENTIFY data might
change after resizing.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Merge ata_read_native_max_addres_ext() into ata_read_native_max_address()
and combine ata_set_native_max_address_ext() and
ata_set_native_max_address() into ata_set_max_sectors().
* reduce duplicate code
* return 0 or -errno depending on error conditions
* report if command fails
* use ATA_LBA instead of 0x40
This is in preparation of ata_hpa_resize() update.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_id_n_sectors() upward right below ata_id_c_string(). This is
to accomodate later changes.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch removes some incorrect formatting spaces and replaces them with tabs.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
simple search-and-replace of direct scsi_cmnd access to
use the data buffer accessors.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is a minimal patch needed to remove use of !use_sg
but it is not a complete clean up of the !use_sg paths.
Libata-core still has the qc->flags & ATA_QCFLAG_SG
and !qc->n_elem code paths. Perhaps an ata maintainer
would have a go at it.
- TODO: further cleanup of qc->flags & ATA_QCFLAG_SG
and !qc->n_elem code paths in libata-core
- TODO: Use scsi_dma_{map,unmap} where applicable.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some iomap functions were still using readl/writel and friends which
happens to work on most platforms but is not correct.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Support the use of '*' in model_num and model_rev entries
in ata_device_blacklist[].
Based largely on David Milburn's "libata-core: support wildcard matching
in ata_blacklist_entry" patch.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Updated and simplified driver. Use only register transfer timing for both
data and register transfers. This gives poorer performance in PIO1 and 2,
but should not be a problem in PIO3 and 4, correct me if I'm wrong :)
The driver works very we'll but I still wonder about the interrupts. I have
an interrupt line, that works nicely when POLLING flag is not set. The
problem is the number of interrupts that eat away my CPU cycles.
When using the POLLING flag there seem to be some interrupts that dosen't get
cleared. Furthermore the device dosen't drive INTRQ high, it stays at 2.5 volts
and generates a lot of interrupts due to ripple / noise. What to do?
Signed-off-by: Kristoffer Nyborg Gregertsen <kngregertsen@norway.atmel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix all issues pointed out in Jeff's email.
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
EH is sometimes repeated without any error or action. For example,
this happens when probing IDENTIFY fails because of a phantom device.
In these cases, all the repeated EH does is making sure there is no
unhandled error or pending action and return. This repeation is
necessary to avoid losing any event which occurred while EH was in
progress.
Unfortunately, this dry run causes annonying "EH pending after
completion" message. This patch moves the repeat reporting into
ata_eh_report() such that it's more compact and skipped on dry runs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mikael Pettersson <mikep@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Currently, port configuration reporting has the following problems.
* iomapped address is reported instead of raw address
* report contains irrelevant fields or lacks necessary fields for
non-SFF controllers.
* host->irq/irq2 are there just for reporting and hacky.
This patch implements and uses ata_port_desc() and
ata_port_pbar_desc(). ata_port_desc() is almost identical to
ata_ehi_push_desc() except that it takes @ap instead of @ehi, has no
locking requirement, can only be used during host initialization and "
" is used as separator instead of ", ". ata_port_pbar_desc() is a
helper to ease reporting of a PCI BAR or an offsetted address into it.
LLD pushes whatever description it wants using the above two
functions. The accumulated description is printed on host
registration after "[S/P]ATA max MAX_XFERMODE ".
SFF init helpers and ata_host_activate() automatically add
descriptions for addresses and irq respectively, so only LLDs which
isn't standard SFF need to add custom descriptions. In many cases,
such controllers need to report different things anyway.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Minor cleanup to remove the unneeded rmb()s per Jeff's advice. Also removed the
pll_clock < 0 check since pll_clock now guaranteed to be >= 0 after Mikael's patch.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If we have a PATA cable with a SATA drive on it then we've found a
bridge and we can flip the cable type. This fixes some cable detect
problems with SATA bridges on chipsets and misdetected cable types.
In theory cable detection and mode limiting is needed if you put a
SATA/PATA bridge on a 40 wire cable, but I see no way to deal with
that other than to point out its not a good idea anyway.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This avoids allocating DMA buffers if not needed but at the moment is
mostly just a neatness item.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was always set to ata_port_disable(). Removed the hook, and replaced
the very few ap->ops->port_disable() callsites with direct calls to
ata_port_disable().
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Testing this on the VIA boards fixes several problems with otherwise
undetectable SATA bridge chips
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We can make use of this on the pata_amd driver as many Nvidia devices
don't have reliable cable detect.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Combined from two Alan Cox patches:
1) libata: ACPI checks for 80wire cable
We can use the ACPI mode information with several drivers as a hint to
cable type. If the ACPI mode set by the BIOS is faster than UDMA33 then
we know the BIOS thinks there are 80wire cables. If it doesn't set such a
mode or it has no ACPI method then we get no further information and can
rely on existing approaches
Introduce the function headers needed. Null it out for non ACPI boxes
Signed-off-by: Alan Cox <alan@redhat.com>
2) libata: ACPI checks for 80wire cable
Provide actual methods for checking if the ACPI support thinks the cable
is 80wire, or doesn't know
Signed-off-by: Alan Cox <alan@redhat.com>
Combined into a single changeset and
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* ->irq_ack() is redundant to what the irq handler already
performs... chk-status + irq-clear. Furthermore, it is only
called in one place, when screaming-irq-debugging is enabled,
so we don't want to bother with a hook just for that.
* ata_dummy_irq_on() is only ever used in drivers that have
no callpath reaching ->irq_on(). Remove .irq_on hook from
those drivers, and the now-unused ata_dummy_irq_on()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remove unneeded, undesirable cast of void*.
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Sonic Zhang <sonic.adi@gmail.com>
Cc: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There is another outstanding issue with ata_piix.c. Intel has never
officially supported anything faster than PATA 100MB/s.
But, the ata_piix.c driver "define" the ICH5 & ICH7 as UDMA6 (aka 133MB/s)
capable. [ Well, no one has probably noticed it before, because there is bug
in do_pata_set_dmamode... Just look at
libata_atapiix_enable_real_udma133.patch and you'll see what wrong with it. ]
Here are Intel's datasheets for the affected chipsets: ICH5 Datasheet:
http://www.intel.com/design/chipsets/datashts/252516.htm (See note on page
183: "... the ICH5 supports reads at the maximum rate of 100MB/s.")
ICH7 Datasheet: http://www.intel.com/design/chipsets/datashts/307013.htm (See
first note on page 190: "... the ICH7 supports reads at the maximum rate of
100MB/s.")
They are two different ways to deal with it:
- Either -
1. replace all ich_pata_133 with ich_pata_100.
(libata_atapiix_disable_udma6.diff - diff from 2.6.22 )
- Or -
2. keep all ich_pata_133 and fix the bug in "do_pata_set_dmamode".
(libata_atapiix_enable_real_udma133.patch - diff from 2.6.22) If there are
any concerns about the safety of the patch patch:
http://lkml.org/lkml/2007/7/6/292 (It was already tested by an Intel
employee, but I guess a bit more user input is necessary here... )
This patch implements 1.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use a stored value for which interrupts to enable. Changing this allows
us to selectively turn off certain interrupts later and have them
stay off.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When we get an SDB FIS with the 'N' bit set, we should send
an event to user space to indicate that there has been a
media change. This will be done via the scsi device.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Check to see if an ATAPI device supports Asynchronous Notification.
If so, enable it, if the host controller supports AN.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Set the MWDMA timing by updating the correct registers. Split the PIO path as
this is mostly shared code. Wants testing.
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Remembered this while doing auditing and code review versus the specs
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for issuing ATA_16 passthru commands to ATAPI devices
managed by libata. It requires the previous CDB length fix patch.
A boot/module parameter, "atapi_passthru16=0" can be used to globally
disable this feature, if ever desired.
tj: restructured __ata_scsi_queuecmd() according to Jeff's suggestion.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Move ata_altstatus() out from ata_hsm_move() to the pio data xfer
functions like ata_pio_sectors() and atapi_pio_bytes() where it makes
more sense.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Debugging a report of a problem with an ancient solid state disk showed
up some problems in the IORDY handling
1. We check the wrong bit to see if the device has IORDY
2. Even then some ancient creaking piles of crap don't support
SETXFER at all.
The cases it fixes are obscure and the risk of side effects is slight
but possible. This also moves us slightly closer to supporting original
MFM/RLL disks with libata.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update hotplug to handle PMP links. When PMP is attached, the PMP
number corresponds to C of SCSI H:C:I:L. While at it, change argument
to ata_find_dev() to @devno from @id to avoid confusion with SCSI
device ID.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ata_eh_autopsy(), ata_eh_report(),
ata_eh_revalidate_and_attach() and ata_eh_recover() to deal with PMP
links. ata_eh_autopsy() and ata_eh_report() updates are
straightforward. They just repeat the same operation over all
configured links. The only change to ata_eh_revalidate_and_attach()
is avoiding calling ->cable_select() on non-host ports.
ata_eh_recover() update is more complex as it first processes all
resets and then performs the rest. This is necessary as thawing with
some links in unknown state can be dangerous. ehi->action is cleared
on successful recovery of a link to avoid repeating recovery due to
failures in other links.
ata_eh_recover() iterates over only PMP links if PMP is attached, and,
on failure, the failing link is returned in @failed_link instead of
disabling devices directly. These are to integrate ata_eh_recover()
into PMP EH later.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update ata_scsi_error() to handle PMP links. As error conditions can
occur on both host and PMP links, __ata_port_for_each_link() is used.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add link->pmp, ap->nr_pmp_links, ap->pmp_link[], and implement/update
link helpers.
printk helpers are updated such that port and link are identifed as
'ataP:' if no PMP is attached, while device is identified as
'ataP.DD:'. If PMP is attached, they become 'ataP:', 'ataP.LL:' and
'ataP.LL' - ie. link and device are identified their PMP number.
If PPM is attached (ap->nr_pmp_links != 0), ata_for_each_link()
iterates over PMP links, while __ata_for_each_link() iterates over the
host link + PMP links. If PMP is not attached (ap->nr_pmp_links ==
0), both iterate over only the host link.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out link initialization into ata_link_init() and
ata_link_init_sata_spd().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
HRST_TO_RESUME and SKIP_D2H_BSY are link attributes. Move them to
ata_link->flags. This will allow host and PMP links to have different
attributes. ata_port_info->link_flags is added and used by LLDs to
specify these flags during initialization.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following functions deal with ata_link instead of ata_port.
* ata_set_mode()
* ata_eh_autopsy() and related functions
* ata_eh_report() and related functions
* suspend/resume related functions
* ata_eh_recover() and related functions
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make reset methods and related functions deal with ata_link instead of
ata_port.
* ata_do_reset()
* ata_eh_reset()
* all prereset/reset/postreset methods and related functions
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ata_eh_about_to_do() and ata_eh_done() deal with ata_link instead
of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the following PHY-related functions to deal with ata_link instead
of ata_port.
* sata_print_link_status()
* sata_down_spd_limit()
* ata_set_sata_spd_limit() and friends
* sata_link_debounce/resume()
* sata_scr_valid/read/write/write_flush()
* ata_link_on/offline()
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Multiple links and different number of devices per link should be
considered to iterate over links and devices. This patch implements
and uses link and device iterators - ata_port_for_each_link() and
ata_link_for_each_dev() - and ata_link_max_devices().
This change makes a lot of functions iterate over only possible
devices instead of from dev 0 to dev ATA_MAX_DEVICES. All such
changes have been examined and nothing should be broken.
While at it, add a separating comment before device helpers to
distinguish them better from link helpers and others.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Introduce ata_link. It abstracts PHY and sits between ata_port and
ata_device. This new level of abstraction is necessary to support
SATA Port Multiplier, which basically adds a bunch of links (PHYs) to
a ATA host port. Fields related to command execution, spd_limit and
EH are per-link and thus moved to ata_link.
This patch only defines the host link. Multiple link handling will be
added later. Also, a lot of ap->link derefences are added but many of
them will be removed as each part is converted to deal directly with
ata_link instead of ata_port.
This patch introduces no behavior change.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
