The fast firmware load hack in cx25840 uses private data. In fact, it
breaks pvrusb2 and doesn't work at all with ivtv. It is a unsafe
implementation and so it is removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch prevents a bug where the frontend is unable to tune after waking
from powered down state. Now, the device remains powered on until it is
disconnected, just like the windows driver. It seems that the bluebird
firmware is unable to successfully handle tuning after a powered down state.
This patch fixes all of the FusionHDTV Bluebird USB2 devices. The Medion
MD95700 will still behave as before, since it was unaffected by this bug.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*) Allow forcing the bandselect value with a module parameter to
facilitate determining the correct bandselect frequencies.
*) Changes the bandselect frequency thresholds based on experiments
with the above parameter in conjunction with the values in the spec.
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
*) Sets an additional tuner parameter (demodulator sample gain) that
wasn't being set before.
*) Removes the low symbol rate tuner parameter tweaks in the previous
patch -- it appears those tweaks are not necessary with the demodulator
sample gain set correctly.
*) Cleanup and document the demodulator register initialization sequence.
*) Change set_fec routine to disable FEC auto scan when a specific code
rate is selected.
*) Remove error message when reported FEC is invalid (which happens
sometimes when the card has no signal)
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The previous DISEQC code didn't wait, so it was unreliable
Signed-off-by: Yeasah Pell <yeasah at schwide.net>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Current debug messages at cx24123 are next to useless, since they don't
print the values sent/read to registers. With this patch, debug=1 will
show comprehensive messages. debug=2 will show also read/write operations
at I2C bus.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
- fixed the reception of channels with low symbol rates.
( The VGA1 and VGA2 offsets recommended by cx24109 docs for
symbol rates from 1 to 5 MSps do not work. I changed them
to values found experimentally. The charge pump current
and FILTUNE voltage are now set to values recommended in
the docs. This improves reception for symbol rates < 15 MSps.
The values written in the SYSSymbolRate registers are calculated
with better precision. )
- fixed the cx24123_get_fec() function. It was returning the values
for DCII mode.
- removed some unused variables
Signed-off-by: Vadim Catana <skystar at moldova.cc>
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In several places we use dev->devno right after we kfree() dev. This fixes
coverity bug id #1065
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Witout this patch tv out don't work properly with my pvr350 card.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The computation in cx88_risc_buffer suffers from the mistake:
a non-zero padding value can cause more page borders to be crossed,
leading to big buffer over-runs.
This patch changes the additive constant from 3 + 4 to 4
It also changees the constant in cx88_risc_databuffer from 3 + 4 to 2,
because 2 dwords are the correct vaule.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It looks like the HD3000 was prototyped with the 7610 tuner when
the driver was developed, but the cards appear to have always shipped
with the 7612 tuner and the driver was never adjusted for it.
The definition needs to be corrected.
- The HD-3000 was prototyped with a Thomson DTT7610,
but production versions used a DTT7612 tuner.
- This patch changes both dvb-pll settings and V4L tuner type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Spotted a couple more places where it fails to check if
dvb_register_adapter() fails.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Now that the CI code reinitialises the frontend, need to move the CI
initialisation to after the frontend init in order to ensure the frontend is
always in a good state. Fixes an oops caused by the frontend being NULL as
well.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When disable_ir=1 parameter is used, or when saa7134_input_init1()
fails for any other reason, dev->remote will remain NULL, and the
driver will oops in saa7134_hwinit2(). Therefore dev->remote must be
checked before dereferencing.
Signed-off-by: Sergey Vlasov <vsu@altlinux.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It turns out the firmware on the TT budget-ci 1.1 slots doesn't generate
interrupts. This patch adds support for this using polling mode on these
slots.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This mutex is meant to stop two devices getting the same ID. dvbdev_get_free_id()
scans the list of already allocated devices to find a free id.
Unfortunately, since the mutex is unlocked before the card is added to the
above list, it is still possible for two of them to get the same id.
Its debatable whether this mutex lock is actually needed, but I'm unwilling
to just remove it in case something does depend on it.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There are tree mistakes on bttv_risc_overlay.
1) When skip_odd is true, the number of lines for which
instructions are written is (height+1)/2, not height/2.
2) This occurs when clipping: the number of instruction bytes
written can be as much as 8 + 12*nclips, not 8 + 8*nclips, as
currently estimated.
3) Coverity check were wrong with nskips=0, since it means that
it can clipped at most one line.
Signed-off-by: Duncan Sands <baldrick@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC]: Fix warning on prom_getproperty in openprom.c
[SPARC]: Handle UNWIND_INFO properly.
[SPARC64]: Update defconfig.
[SPARC]: show device name in /proc/dvma_map
[SPARC]: Remove duplicate symbol exports
Fix race condition during destruction calls to avoid possibility of
accessing object after it has been freed. Instead of waking up a wait
queue directly, which is susceptible to a race where the object is
freed between the reference count going to 0 and the wake_up(), use a
completion to wait in the function doing the freeing.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The ipath driver's table of PCI IDs needs a { 0, } entry at the end.
This makes all of the device aliases visible to userspace so hotplug
loads the module for all supported devices. Without the patch,
modinfo ipath_core only shows:
alias: pci:v00001FC1d0000000Dsv*sd*bc*sc*i*
instead of the correct:
alias: pci:v00001FC1d00000010sv*sd*bc*sc*i*
alias: pci:v00001FC1d0000000Dsv*sd*bc*sc*i*
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: Bryan O'Sullivan <bos@pathscale.com>
For sparc32 we need R_SPARC_UA32 relocation support, for
sparc64 we need the handle R_SPARC_DISP32 relocations.
Based upon reports and initial patch by Martin Habets.
Signed-off-by: David S. Miller <davem@davemloft.net>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/i2c-2.6:
[PATCH] scx200_acb: Fix for the CS5535 errata
[PATCH] scx200_acb: Fix resource name use after free
[PATCH] scx200_acb: Fix return on init error
This reverts commit 56cf6504fc.
Both Erik Mouw and Andrew Vasquez independently pinpointed this commit
as causing problems, where the slab cache for a driver is never released
(most obviously causing problems when immediately re-loading that
driver, resulting in a "kmem_cache_create: duplicate cache <xyz>"
message, but it can also cause other trouble).
James Bottomley dug into it, and reports:
"OK, here's the scoop. The problem patch adds a get of driverfs_dev in
add_disk(), but doesn't put it again until disk_release() (which occurs
on final put_disk() of the gendisk).
However, in SCSI, the driverfs_dev is the sdev_gendev. That means
there's a reference held on sdev_gendev until final disk put.
Unfortunately, we use the driver model driver_remove to trigger
del_gendisk (which removes the gendisk from visibility and decrements
the refcount), so we've introduced an unbreakable deadlock in the
reference counting with this.
I suggest simply reversing this patch at the moment. If Russell and
Jens can tell me what they're trying to do I'll see if there's another
way to do it."
so hereby the patch gets reverted, waiting for a better fix.
Cc: Jens Axboe <axboe@suse.de>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Erik Mouw <erik@harddisk-recovery.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I introduced this way back in 2.6.13 when adding the port lock logic.
This device talks out through different "ports" all at the same time, so
the lock logic was wrong, preventing any data from ever being sent
properly.
Thanks a lot to Bernhard Reiter <bernhard@intevation.de> for being
patient and helping with debugging this.
Cc: Bernhard Reiter <bernhard@intevation.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Based on Simon's original driver, with some minor code cleanups and
tidying by me.
Cc: Simon Schulz <simon@auctionant.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If serial_open() fails at the port assignment or mutex_lock_interruptible()
is interrupted, the 'serial' object will never be freed.
We should call kref_put() when those errors happens.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the device is disconnected while serial_open() is executing and
either try_module_get() or the device specific open function fails, the
kref_put() call in the 'bailout_kref_put' label will free the memory
pointed out by 'port'.
The subsequent dereferences in the 'bailout_kref_put' label will be
invalid.
The fix is just to assure kref_put() is called after any 'port' usage.
Signed-off-by: Luiz Fernando N. Capitulino <lcapitulino@mandriva.com.br>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's become apparent as machines get faster that the emagic kernel firmware
loaders (based on the ezusb loader) have a reset race. a 400MHz TiBook
never tripped it, but a 2GHz Pentium M seems to hit it about 30% of the
time. The bug is seen as a hung USB box and the kernel error:
drivers/usb/misc/emi62.c: emi62_load_firmware - error loading firmware:
error = -110
The patch below inserts a delay after deasserting reset to allow the box to
settle before a new command is issued. This affects only device startup.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After recent changes, the USB keyboard as shipped with IBM pSeries systems
does not work anymore, unless the keyboard is replugged after reboot.
Adding this model to the blacklist fixes it.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the Sierra Wireless card to airprime.c.
I tested this on my laptop.
Signed-off-by: Ken Brush <ken@cgi101.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] 8250: add locking to console write function
[SERIAL] Remove unconditional enable of TX irq for console
[SERIAL] 8250: set divisor register correctly for AMD Alchemy SoC uart
[SERIAL] AMD Alchemy UART: claim memory range
[SERIAL] Clean up serial locking when obtaining a reference to a port
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
[IPV6]: skb leakage in inet6_csk_xmit
[BRIDGE]: Do sysfs registration inside rtnl.
[NET]: Do sysfs registration as part of register_netdevice.
[TG3]: Fix possible NULL deref in tg3_run_loopback().
[NET] linkwatch: Handle jiffies wrap-around
[IRDA]: Switching to a workqueue for the SIR work
[IRDA]: smsc-ircc: Minimal hotplug support.
[IRDA]: Removing unused EXPORT_SYMBOLs
[IRDA]: New maintainer.
[NET]: Make netdev_chain a raw notifier.
[IPV4]: ip_options_fragment() has no effect on fragmentation
[NET]: Add missing operstates documentation.
Don't recurse back into the driver even if the unplug threshold is met,
when the driver asks for a requeue. This is both silly from a logical
point of view (requeues typically happen due to driver/hardware
shortage), and also dangerous since we could hit an endless request_fn
-> requeue -> unplug -> request_fn loop and crash on stack overrun.
Also limit blk_run_queue() to one level of recursion, similar to how
blk_start_queue() works.
This patch fixed a real problem with SLES10 and lpfc, and it could hit
any SCSI lld that returns non-zero from it's ->queuecommand() handler.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When deleting the last child the level of a class should drop to zero.
Noticed by Andreas Mueller <andreas@stapelspeicher.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Biederman points out that we can't take the task_lock while holding
tasklist_lock for writing, because another CPU that holds the task lock
might take an interrupt that then tries to take tasklist_lock for writing.
Which would be a nasty deadlock, with one CPU spinning forever in an
interrupt handler (although admittedly you need to really work at
triggering it ;)
Since the ptrace_attach() code is special and very unusual, just make it
be extra careful, and use trylock+repeat to avoid the possible deadlock.
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
