Fix codingstyle issues, and make the minimum version for cx18-alsa required
to be 2.6.17, so that we don't need all the #ifdefs related to the changes
to ALSA structures.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Address coding style issue with cx18-alsa-main.c
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If the stream is already in use, make sure we free up the memory allocated
earlier.
Thanks to Andy Wall for reviewing and pointing this out.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove a couple of warnings from dead code during driver development.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Use the cx18 board name in the ALSA description, to make it easier for users
who run "arecord -l" to see which device they should be looking for.
Also, use strlcpy() instead of strcpy().
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix the debug macro so that it is dependent on the modprobe parameter.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Restructure the way the module gets loaded so that it gets loaded automatically
when cx18 is loaded, and make it work properly if there are multiple cards
present (since the old code would only take one opportunity to connect to cx18
instances when the module first loaded).
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Remove an unneeded debug line, which was preventing the cx18-alsa module from
loading.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Export a couple of more symbols required by the cx18-alsa module.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add cx18-alsa to the Makefile and Kconfig
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add code so that the PCM ALSA device actually works, and update the
cx18-streams mechanism so that it passes the data off to the cx18-alsa module.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Expose a couple of symbols in the cx18 module so that locking of the PCM
stream can be shared with the cx18-alsa module.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Fix some basic compilation issues with Andy's original code. In particular,
temporarily #ifdef out the mixer code, add some additional exception handling,
fix a couple of typos, and add a copyright line.
This work was sponsored by ONELAN Limited.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Rename cx18-alsa.c to cx18-alsa-main.c so that we can call the final .ko file
cx18-alsa.ko
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is for better readability and smaller size of code lines.
Also it is for future improvements like GPIO handling.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is for better readability and smaller size of code.
Also it is similar to other drivers.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The PCI card contains dm1105 PCI bridge and ds3000 demod.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Martin Dauskardt <martin.dauskardt@gmx.de> has done extensive testing on what
values can be used and and concluded that only 300 ms total is required to
avoid bad video effects such as occasional black screen and short sync
disturbances. Furthermore he determined how this 300 ms was split between
the two msleep()s did matter very much, so he suggested 150ms/150ms as one
acceptable alternative that is implemented here.
Many thanks go to Martin.
Tested-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This change attempts to fix the ivtv tinny audio problem by keeping digitizer
to encoder audio clocks running, while disabling the video clocks as needed to
avoid unpredictable PCI bus hangs.
To accomplish this, for the cx25840 module enabling of audio streaming had
to be separated from enabling video streaming, requiring an additional
v4l2_subdev_audio_op and calls to this new op in the pvrusb2 and ivtv drivers.
The cx231xx and cx23885 driver use the cx25840 module for affecting only
video on s_stream calls, so those drivers needed no change.
The CX23418 hardware does not exhibit either the tinny audio problem nor the PCI
bus hang, so the cx18 driver did not need corresponding changes.
CX2341[56] based cards that are not using the CX2584x family of chips
do not seem to be affected by the tinny audio problem, and this change should
not affect how they are configured. It will delay their first capture by
starting by another 300 msec though.
Many thanks go to Argus <pthorn-ivtvd@styx2002.no-ip.org> and
Martin Dauskardt <martin.dauskardt@gmx.de> whose persistent testing and
investigation of this problem will hopefully fix this problem once and for all
for many ivtv users.
Reported-by: Martin Dauskardt <martin.dauskardt@gmx.de>
Reported-by: Argus <pthorn-ivtvd@styx2002.no-ip.org>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
There are several DMA related interrupts which wake up the dma_waitq. The udma
routines use this queue while they wait for their transfer to complete. When
woken, the udma routine will check the IVTV_F_I_UDMA_PENDING & IVTV_F_I_UDMA
flags to see if the transfer is still queued or has finished. However, a small
window exists between the IVTV_F_I_UDMA_PENDING flag being cleared and the
IVTV_F_I_UDMA flag being set. Given that the completion of an unrelated DMA
transfer may wake up the udma routine, it's possible for this check to fail
and the udma routine will start unmapping pages when the transfer has only
just started. The result of this is unpredictable.
This fix simply delays the clearing of the IVTV_F_I_UDMA_PENDING flag until
after IVTV_F_I_UDMA has been set.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Andy Walls <awalls@radix.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
22-kHz tone can be driven in two ways:
1. LNBH24 can produce 22kHz continuous tone when TEN=1 ( 22 KHz tone output is
always activated ).
2. LNBH24 can reproduce 22kHz tone timings from DSQIN or EXTM pin's when TEN=0.
From LNBH24 datasheet:
"In order to improve design flexibility an external tone input pin is
available (EXTM). The EXTM is a Logic input pin which activates the 22 kHz
tone output, on the VoTX pin, by using the LNBH24 integrated tone generator
(similar to the DSQIN pin function). In fact, the output tone waveform
characteristics will always be internally controlled by the LNBH24 tone
generator and the EXTM signal will be used as a timing control for DiSEqC tone
data encoding on the VoTX output."
In NetUP Dual DVB-S2-CI card 22kHz tone timings on EXTM pin produced by
STV0900 demod:
.set_tone = stv0900_set_tone
redefine to "set_tone = lnbp21_set_tone" is not correct for "NetUP Dual
DVB-S2-CI card".
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
We have some duplicate functionality between the zc0301 and gspca-zc3xx,
the sn9c102 and gspca-sonixb + gspca-sonix, and et61x251 and gscpa-etoms
drivers.
The non gspca versions of these drivers not only show a lot of code
duplicty (amongsth each other), as they all copy the same generic usb
webcam code instead of using some sort of framework. They also have not
seen any updates for more then 2 years, where as the gspca drivers are
actively maintained.
So it is time for the non gspca versions of these drivers to go away,
marking them as deprecated is the first step in this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
drivers/media/video/Kconfig: Turn deprecated drivers off by default
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This new driver supports USB PIA CPiA version 1 cams, replacing the
old v4l1 driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When both the gspca_sonixb and the sn9c102 driver are enabled, make the
gspca_sonixb driver handle cams with usb-id of 0c45:6007. The sn9c102 driver
is being phased out and gspca driver has been successfully tested
with an 0c45:6007 camara.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Our hstart value was wrong for tas5110d sensor using sonixb cams, this
patch fixes this. Many thanks to Paulus (laudaka) for donating me a camera
with such a sensor IC.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
ov764x remove setting of AEC limits, as the custom values cause AEC
oscilation in 320x240.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
gspca_ov519: remove non functioning contrast control for ov764x sensor
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Differentiate between ov7640 and ov7648 and handle the ov7648 320x240
on the ov519 bridge specially to fix r and b being swapped.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Michael Deegan <michael@ucc.gu.uwa.edu.au>, has reported issues with
using 640x480 mode on his ov518+ webcam. The fix for this breaks things
on my ov518+ cam (Trust 320 Sp@cecam), this patch thus adds differentiation
in the driver between the OV7620 sensor his cam has and the OV7620AE sensor
my cam has, and then only changes the init sequence for the ov518+ +
OV7620 combo which was not working for Michael.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Streaming of VGA stv0680 based cams (instead of CIF ones) failed, because
we were using the wrong control pipe for certain commands, this patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Mark led on eyetoy II as inverted, I have the feeling the led needs to
be inverted for all 519 based cams (iow we got the set led code wrong), but
lets just deal with this one cam at a time to avoid breaking currently
working cams.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
stv0680 cameras currently only work when already plugged in when the system
boots (or when manually re-loading the driver after boot). This patch fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
New gspca subdriver adding support for SN9C2028 dual-mode cameras.
Signed-off-by: Theodore Kilgore <kilgota@banach.math.auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
If you read the mail to Oliver Neukum on the linux-usb list, then you know
that I found a cure for the mysterious problem that the MR97310a CIF "type
1" cameras have been freezing up and refusing to stream if hooked up to a
machine with a UHCI controller.
Namely, the cure is that if the camera is an mr97310a CIF type 1 camera, you
have to send it 0xa0, 0x00. Somehow, this is a timing reset command, or
such. It un-blocks whatever was previously stopping the CIF type 1 cameras
from working on the UHCI-based machines.
Signed-off-by: Theodore Kilgore <kilgota@auburn.edu>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Exit stv090x_algo() if the tuner did not lock. This might happen due to
missing signal or invalid/incomplete tuning parameters.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
The I2C gate must also be disabled, if a tuner command failed.
Otherwise the tuner mutex would be locked forever.
Signed-off-by: Oliver Endriss <o.endriss@gmx.de>
Signed-off-by: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When mclk is not 0 then it will never be set to the correct value and
the Demodulator will not work.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This gives the STV090x and improved clock signal (rectangle instead of sine).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Using clk_div member of stv6110x_config structure the tuner's clock
output divider can be configured. It is set in stv6110x_attach.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This is needed when clock input is driven from tuner and an output
divider different from 1 is used.
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Before there was used a static register map that could lead to issues
when there are are multiple adapters with the STV6110(A).
Signed-off-by: Andreas Regel <andreas.regel@gmx.de>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
