Follow-up to 45160cebd6 ("net: veth: Disable netpoll support") to
also disable netpoll for netkit interfaces. Same conditions apply
here as well.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Breno Leitao <leitao@debian.org>
Cc: Nikolay Aleksandrov <razor@blackwall.org>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Breno Leitao <leitao@debian.org>
Link: https://lore.kernel.org/r/eab2d69ba2f4c260aef62e4ff0d803e9f60c2c5d.1724414250.git.daniel@iogearbox.net
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Boris Sukholitko says:
====================
tc: adjust network header after 2nd vlan push
<tldr>
skb network header of the single-tagged vlan packet continues to point the
vlan payload (e.g. IP) after second vlan tag is pushed by tc act_vlan. This
causes problem at the dissector which expects double-tagged packet network
header to point to the inner vlan.
The fix is to adjust network header in tcf_act_vlan.c but requires
refactoring of skb_vlan_push function.
</tldr>
Consider the following shell script snippet configuring TC rules on the
veth interface:
ip link add veth0 type veth peer veth1
ip link set veth0 up
ip link set veth1 up
tc qdisc add dev veth0 clsact
tc filter add dev veth0 ingress pref 10 chain 0 flower \
num_of_vlans 2 cvlan_ethtype 0x800 action goto chain 5
tc filter add dev veth0 ingress pref 20 chain 0 flower \
num_of_vlans 1 action vlan push id 100 \
protocol 0x8100 action goto chain 5
tc filter add dev veth0 ingress pref 30 chain 5 flower \
num_of_vlans 2 cvlan_ethtype 0x800 action simple sdata "success"
Sending double-tagged vlan packet with the IP payload inside:
cat <<ENDS | text2pcap - - | tcpreplay -i veth1 -
0000 00 00 00 00 00 11 00 00 00 00 00 22 81 00 00 64 ..........."...d
0010 81 00 00 14 08 00 45 04 00 26 04 d2 00 00 7f 11 ......E..&......
0020 18 ef 0a 00 00 01 14 00 00 02 00 00 00 00 00 12 ................
0030 e1 c7 00 00 00 00 00 00 00 00 00 00 ............
ENDS
will match rule 10, goto rule 30 in chain 5 and correctly emit "success" to
the dmesg.
OTOH, sending single-tagged vlan packet:
cat <<ENDS | text2pcap - - | tcpreplay -i veth1 -
0000 00 00 00 00 00 11 00 00 00 00 00 22 81 00 00 14 ..........."....
0010 08 00 45 04 00 2a 04 d2 00 00 7f 11 18 eb 0a 00 ..E..*..........
0020 00 01 14 00 00 02 00 00 00 00 00 16 e1 bf 00 00 ................
0030 00 00 00 00 00 00 00 00 00 00 00 00 ............
ENDS
will match rule 20, will push the second vlan tag but will *not* match
rule 30. IOW, the match at rule 30 fails if the second vlan was freshly
pushed by the kernel.
Lets look at __skb_flow_dissect working on the double-tagged vlan packet.
Here is the relevant code from around net/core/flow_dissector.c:1277
copy-pasted here for convenience:
if (dissector_vlan == FLOW_DISSECTOR_KEY_MAX &&
skb && skb_vlan_tag_present(skb)) {
proto = skb->protocol;
} else {
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
data, hlen, &_vlan);
if (!vlan) {
fdret = FLOW_DISSECT_RET_OUT_BAD;
break;
}
proto = vlan->h_vlan_encapsulated_proto;
nhoff += sizeof(*vlan);
}
The "else" clause above gets the protocol of the encapsulated packet from
the skb data at the network header location. printk debugging has showed
that in the good double-tagged packet case proto is
htons(0x800 == ETH_P_IP) as expected. However in the single-tagged packet
case proto is garbage leading to the failure to match tc filter 30.
proto is being set from the skb header pointed by nhoff parameter which is
defined at the beginning of __skb_flow_dissect
(net/core/flow_dissector.c:1055 in the current version):
nhoff = skb_network_offset(skb);
Therefore the culprit seems to be that the skb network offset is different
between double-tagged packet received from the interface and single-tagged
packet having its vlan tag pushed by TC.
Lets look at the interesting points of the lifetime of the single/double
tagged packets as they traverse our packet flow.
Both of them will start at __netif_receive_skb_core where the first vlan
tag will be stripped:
if (eth_type_vlan(skb->protocol)) {
skb = skb_vlan_untag(skb);
if (unlikely(!skb))
goto out;
}
At this stage in double-tagged case skb->data points to the second vlan tag
while in single-tagged case skb->data points to the network (eg. IP)
header.
Looking at TC vlan push action (net/sched/act_vlan.c) we have the following
code at tcf_vlan_act (interesting points are in square brackets):
if (skb_at_tc_ingress(skb))
[1] skb_push_rcsum(skb, skb->mac_len);
....
case TCA_VLAN_ACT_PUSH:
err = skb_vlan_push(skb, p->tcfv_push_proto, p->tcfv_push_vid |
(p->tcfv_push_prio << VLAN_PRIO_SHIFT),
0);
if (err)
goto drop;
break;
....
out:
if (skb_at_tc_ingress(skb))
[3] skb_pull_rcsum(skb, skb->mac_len);
And skb_vlan_push (net/core/skbuff.c:6204) function does:
err = __vlan_insert_tag(skb, skb->vlan_proto,
skb_vlan_tag_get(skb));
if (err)
return err;
skb->protocol = skb->vlan_proto;
[2] skb->mac_len += VLAN_HLEN;
in the case of pushing the second tag. Lets look at what happens with
skb->data of the single-tagged packet at each of the above points:
1. As a result of the skb_push_rcsum, skb->data is moved back to the start
of the packet.
2. First VLAN tag is moved from the skb into packet buffer, skb->mac_len is
incremented, skb->data still points to the start of the packet.
3. As a result of the skb_pull_rcsum, skb->data is moved forward by the
modified skb->mac_len, thus pointing to the network header again.
Then __skb_flow_dissect will get confused by having double-tagged vlan
packet with the skb->data at the network header.
The solution for the bug is to preserve "skb->data at second vlan header"
semantics in the skb_vlan_push function. We do this by manipulating
skb->network_header rather than skb->mac_len. skb_vlan_push callers are
updated to do skb_reset_mac_len.
More about the patch series:
* patch 1 fixes skb_vlan_push and the callers
* patch 2 adds ingress tc_actions test
* patch 3 adds egress tc_actions test
====================
Link: https://patch.msgid.link/20240822103510.468293-1-boris.sukholitko@broadcom.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add new test checking the correctness of inner vlan flushing to the skb
data when outer vlan tag is added through act_vlan on egress.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add new test checking the correctness of inner vlan flushing to the skb
data when outer vlan tag is added through act_vlan on ingress.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
<tldr>
skb network header of the single-tagged vlan packet continues to point the
vlan payload (e.g. IP) after second vlan tag is pushed by tc act_vlan. This
causes problem at the dissector which expects double-tagged packet network
header to point to the inner vlan.
The fix is to adjust network header in tcf_act_vlan.c but requires
refactoring of skb_vlan_push function.
</tldr>
Consider the following shell script snippet configuring TC rules on the
veth interface:
ip link add veth0 type veth peer veth1
ip link set veth0 up
ip link set veth1 up
tc qdisc add dev veth0 clsact
tc filter add dev veth0 ingress pref 10 chain 0 flower \
num_of_vlans 2 cvlan_ethtype 0x800 action goto chain 5
tc filter add dev veth0 ingress pref 20 chain 0 flower \
num_of_vlans 1 action vlan push id 100 \
protocol 0x8100 action goto chain 5
tc filter add dev veth0 ingress pref 30 chain 5 flower \
num_of_vlans 2 cvlan_ethtype 0x800 action simple sdata "success"
Sending double-tagged vlan packet with the IP payload inside:
cat <<ENDS | text2pcap - - | tcpreplay -i veth1 -
0000 00 00 00 00 00 11 00 00 00 00 00 22 81 00 00 64 ..........."...d
0010 81 00 00 14 08 00 45 04 00 26 04 d2 00 00 7f 11 ......E..&......
0020 18 ef 0a 00 00 01 14 00 00 02 00 00 00 00 00 12 ................
0030 e1 c7 00 00 00 00 00 00 00 00 00 00 ............
ENDS
will match rule 10, goto rule 30 in chain 5 and correctly emit "success" to
the dmesg.
OTOH, sending single-tagged vlan packet:
cat <<ENDS | text2pcap - - | tcpreplay -i veth1 -
0000 00 00 00 00 00 11 00 00 00 00 00 22 81 00 00 14 ..........."....
0010 08 00 45 04 00 2a 04 d2 00 00 7f 11 18 eb 0a 00 ..E..*..........
0020 00 01 14 00 00 02 00 00 00 00 00 16 e1 bf 00 00 ................
0030 00 00 00 00 00 00 00 00 00 00 00 00 ............
ENDS
will match rule 20, will push the second vlan tag but will *not* match
rule 30. IOW, the match at rule 30 fails if the second vlan was freshly
pushed by the kernel.
Lets look at __skb_flow_dissect working on the double-tagged vlan packet.
Here is the relevant code from around net/core/flow_dissector.c:1277
copy-pasted here for convenience:
if (dissector_vlan == FLOW_DISSECTOR_KEY_MAX &&
skb && skb_vlan_tag_present(skb)) {
proto = skb->protocol;
} else {
vlan = __skb_header_pointer(skb, nhoff, sizeof(_vlan),
data, hlen, &_vlan);
if (!vlan) {
fdret = FLOW_DISSECT_RET_OUT_BAD;
break;
}
proto = vlan->h_vlan_encapsulated_proto;
nhoff += sizeof(*vlan);
}
The "else" clause above gets the protocol of the encapsulated packet from
the skb data at the network header location. printk debugging has showed
that in the good double-tagged packet case proto is
htons(0x800 == ETH_P_IP) as expected. However in the single-tagged packet
case proto is garbage leading to the failure to match tc filter 30.
proto is being set from the skb header pointed by nhoff parameter which is
defined at the beginning of __skb_flow_dissect
(net/core/flow_dissector.c:1055 in the current version):
nhoff = skb_network_offset(skb);
Therefore the culprit seems to be that the skb network offset is different
between double-tagged packet received from the interface and single-tagged
packet having its vlan tag pushed by TC.
Lets look at the interesting points of the lifetime of the single/double
tagged packets as they traverse our packet flow.
Both of them will start at __netif_receive_skb_core where the first vlan
tag will be stripped:
if (eth_type_vlan(skb->protocol)) {
skb = skb_vlan_untag(skb);
if (unlikely(!skb))
goto out;
}
At this stage in double-tagged case skb->data points to the second vlan tag
while in single-tagged case skb->data points to the network (eg. IP)
header.
Looking at TC vlan push action (net/sched/act_vlan.c) we have the following
code at tcf_vlan_act (interesting points are in square brackets):
if (skb_at_tc_ingress(skb))
[1] skb_push_rcsum(skb, skb->mac_len);
....
case TCA_VLAN_ACT_PUSH:
err = skb_vlan_push(skb, p->tcfv_push_proto, p->tcfv_push_vid |
(p->tcfv_push_prio << VLAN_PRIO_SHIFT),
0);
if (err)
goto drop;
break;
....
out:
if (skb_at_tc_ingress(skb))
[3] skb_pull_rcsum(skb, skb->mac_len);
And skb_vlan_push (net/core/skbuff.c:6204) function does:
err = __vlan_insert_tag(skb, skb->vlan_proto,
skb_vlan_tag_get(skb));
if (err)
return err;
skb->protocol = skb->vlan_proto;
[2] skb->mac_len += VLAN_HLEN;
in the case of pushing the second tag. Lets look at what happens with
skb->data of the single-tagged packet at each of the above points:
1. As a result of the skb_push_rcsum, skb->data is moved back to the start
of the packet.
2. First VLAN tag is moved from the skb into packet buffer, skb->mac_len is
incremented, skb->data still points to the start of the packet.
3. As a result of the skb_pull_rcsum, skb->data is moved forward by the
modified skb->mac_len, thus pointing to the network header again.
Then __skb_flow_dissect will get confused by having double-tagged vlan
packet with the skb->data at the network header.
The solution for the bug is to preserve "skb->data at second vlan header"
semantics in the skb_vlan_push function. We do this by manipulating
skb->network_header rather than skb->mac_len. skb_vlan_push callers are
updated to do skb_reset_mac_len.
Signed-off-by: Boris Sukholitko <boris.sukholitko@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Arkadiusz Kubalewski says:
====================
Add Embedded SYNC feature for a dpll's pin
Introduce and allow DPLL subsystem users to get/set capabilities of
Embedded SYNC on a dpll's pin.
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
====================
Link: https://patch.msgid.link/20240822222513.255179-1-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to get and set configuration of Embedded SYNC feature
on the ice driver dpll pins.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20240822222513.255179-3-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement and document new pin attributes for providing Embedded SYNC
capabilities to the DPLL subsystem users through a netlink pin-get
do/dump messages. Allow the user to set Embedded SYNC frequency with
pin-set do netlink message.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20240822222513.255179-2-arkadiusz.kubalewski@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the function dpaa_napi_del(), we execute the netif_napi_del()
for each cpu, which is actually a high overhead operation
because each call to netif_napi_del() contains a synchronize_net(),
i.e. an RCU operation. In fact, it is only necessary to call
__netif_napi_del and use synchronize_net() once outside of the loop.
This change is similar to commit 2543a6000e ("gro_cells: reduce
number of synchronize_net() calls") and commit 5198d545db (" net:
remove napi_hash_del() from driver-facing API") 5198d545db.
Signed-off-by: Xi Huang <xuiagnh@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240822072042.42750-1-xuiagnh@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
ipv6_setsockopt() can directly call ip_setsockopt()
instead of going through udp_prot.setsockopt()
ipv6_getsockopt() can directly call ip_getsockopt()
instead of going through udp_prot.getsockopt()
These indirections predate git history, not sure why they
were there.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240823140019.3727643-1-edumazet@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The macro sk_for_each_bound_bhash accepts a parameter
__sk, but it was not used, rather the sk2 is directly
used, so we replace the sk2 with __sk in macro.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Link: https://patch.msgid.link/20240823070453.3327832-1-lihongbo22@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
We found that one close-wait socket was reset by the other side
due to a new connection reusing the same port which is beyond our
expectation, so we have to investigate the underlying reason.
The following experiment is conducted in the test environment. We
limit the port range from 40000 to 40010 and delay the time to close()
after receiving a fin from the active close side, which can help us
easily reproduce like what happened in production.
Here are three connections captured by tcpdump:
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965525191
127.0.0.1.9999 > 127.0.0.1.40002: Flags [S.], seq 2769915070
127.0.0.1.40002 > 127.0.0.1.9999: Flags [.], ack 1
127.0.0.1.40002 > 127.0.0.1.9999: Flags [F.], seq 1, ack 1
// a few seconds later, within 60 seconds
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965590730
127.0.0.1.9999 > 127.0.0.1.40002: Flags [.], ack 2
127.0.0.1.40002 > 127.0.0.1.9999: Flags [R], seq 2965525193
// later, very quickly
127.0.0.1.40002 > 127.0.0.1.9999: Flags [S], seq 2965590730
127.0.0.1.9999 > 127.0.0.1.40002: Flags [S.], seq 3120990805
127.0.0.1.40002 > 127.0.0.1.9999: Flags [.], ack 1
As we can see, the first flow is reset because:
1) client starts a new connection, I mean, the second one
2) client tries to find a suitable port which is a timewait socket
(its state is timewait, substate is fin_wait2)
3) client occupies that timewait port to send a SYN
4) server finds a corresponding close-wait socket in ehash table,
then replies with a challenge ack
5) client sends an RST to terminate this old close-wait socket.
I don't think the port selection algo can choose a FIN_WAIT2 socket
when we turn on tcp_tw_reuse because on the server side there
remain unread data. In some cases, if one side haven't call close() yet,
we should not consider it as expendable and treat it at will.
Even though, sometimes, the server isn't able to call close() as soon
as possible like what we expect, it can not be terminated easily,
especially due to a second unrelated connection happening.
After this patch, we can see the expected failure if we start a
connection when all the ports are occupied in fin_wait2 state:
"Ncat: Cannot assign requested address."
Reported-by: Jade Dong <jadedong@tencent.com>
Signed-off-by: Jason Xing <kernelxing@tencent.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://patch.msgid.link/20240823001152.31004-1-kerneljasonxing@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Kyle Swenson says:
====================
net: pse-pd: tps23881: Reset GPIO support
On some boards, the TPS2388x's reset line (active low) is pulled low to
keep the chip in reset until the SoC pulls the device out of reset.
This series updates the device-tree binding for the tps23881 and then
adds support for the reset gpio handling in the tps23881 driver.
v1: https://lore.kernel.org/20240819190151.93253-1-kyle.swenson@est.tech
====================
Link: https://patch.msgid.link/20240822220100.3030184-1-kyle.swenson@est.tech
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TPS23880/1 has an active-low reset pin that some boards connect to
the SoC to control when the TPS23880 is pulled out of reset.
Add support for this via a reset-gpios property in the DTS.
Signed-off-by: Kyle Swenson <kyle.swenson@est.tech>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240822220100.3030184-3-kyle.swenson@est.tech
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The TPS23881 has an active-low reset pin that can be connected to an
SoC. Document this with the device-tree binding.
Signed-off-by: Kyle Swenson <kyle.swenson@est.tech>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/20240822220100.3030184-2-kyle.swenson@est.tech
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Although commit 4a4cd70369 ("l2tp: don't set sk_user_data in tunnel socket")
removed sk->sk_user_data usage, setup_udp_tunnel_sock() still touches
sk->sk_user_data, this conflicts with sockmap which also leverages
sk->sk_user_data to save psock.
Restore this sk->sk_user_data check to avoid such conflicts.
Fixes: 4a4cd70369 ("l2tp: don't set sk_user_data in tunnel socket")
Reported-by: syzbot+8dbe3133b840c470da0e@syzkaller.appspotmail.com
Cc: Tom Parkin <tparkin@katalix.com>
Signed-off-by: Cong Wang <cong.wang@bytedance.com>
Tested-by: James Chapman <jchapman@katalix.com>
Reviewed-by: James Chapman <jchapman@katalix.com>
Link: https://patch.msgid.link/20240822182544.378169-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Sean Anderson says:
====================
net: xilinx: axienet: Multicast fixes and improvements
This series has a few small patches improving the handling of multicast
addresses. In particular, it makes the driver a whole lot less spammy,
and adjusts things so we aren't in promiscuous mode when we have more
than four multicast addresses (a common occurance on modern systems).
As the hardware has a 4-entry CAM, the ideal method would be to "pack"
multiple addresses into one CAM entry. Something like:
entry.address = address[0] | address[1];
entry.mask = ~(address[0] ^ address[1]);
Which would make the entry match both addresses (along with some others
that would need to be filtered in software).
Mapping addresses to entries in an efficient way is a bit tricky. If
anyone knows of an in-tree example of something like this, I'd be glad
to hear about it.
====================
Link: https://patch.msgid.link/20240822154059.1066595-1-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for IFF_ALLMULTI by configuring a single filter to match the
multicast address bit. This allows us to keep promiscuous mode disabled,
even when we have more than four multicast addresses. An even better
solution would be to "pack" addresses into the available CAM registers,
but that can wait for a future series.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-6-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Contrary to the comment, we don't have to inform the net subsystem.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-5-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A message about being in promiscuous mode is printed every time each
additional multicast address beyond four is added. Suppress this message
like is done in other drivers.
Signed-off-by: Sean Anderson <sean.anderson@linux.dev>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822154059.1066595-4-sean.anderson@linux.dev
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Li Zetao says:
====================
Some modifications to optimize code readability
This patchset is mainly optimized for readability in contexts where size
needs to be determined. By using min() or max(), or even directly
removing redundant judgments (such as the 5th patch), the code is more
consistent with the context.
====================
Link: https://patch.msgid.link/20240822133908.1042240-1-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When calculating size of own domain based on number of peers, the result
should be less than MAX_MON_DOMAIN, so using min() here is very semantic.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822133908.1042240-8-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When coping sockaddr in ip6_mc_msfget(), the time of copies
depends on the minimum value between sl_count and gf_numsrc.
Using min() here is very semantic.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822133908.1042240-7-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
When processing the tail append of sk buffer, the final length needs
to be determined based on expectlen and addlen. Using max() here can
increase the readability of the code.
Signed-off-by: Li Zetao <lizetao1@huawei.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822133908.1042240-4-lizetao1@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simon Horman says:
====================
net: header and core spelling corrections
This patchset addresses a number of spelling errors in comments in
Networking files under include/, and files in net/core/. Spelling
problems are as flagged by codespell.
It aims to provide patches that can be accepted directly into net-next.
And splits patches up based on maintainer boundaries: many things
feed directly into net-next. This is a complex process and I apologise
for any errors.
I also plan to address, via separate patches, spelling errors in other
files in the same directories, for files whose changes typically go
through trees other than net-next (which feed into net-next).
====================
Link: https://patch.msgid.link/20240822-net-spell-v1-0-3a98971ce2d2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct spelling in sctp.h and structs.h.
As reported by codespell.
Cc: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Acked-by: Xin Long <lucien.xin@gmail.com>
Link: https://patch.msgid.link/20240822-net-spell-v1-10-3a98971ce2d2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct spelling in NFC headers.
As reported by codespell.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240822-net-spell-v1-8-3a98971ce2d2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct spelling in if_rmnet.h
As reported by codespell.
Cc: Sean Tranchetti <quic_stranche@quicinc.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Subash Abhinov Kasiviswanathan <quic_subashab@quicinc.com>
Link: https://patch.msgid.link/20240822-net-spell-v1-6-3a98971ce2d2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct spelling in bond_3ad.h and bond_alb.h.
As reported by codespell.
Cc: Jay Vosburgh <jv@jvosburgh.net>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822-net-spell-v1-5-3a98971ce2d2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Correct spelling in iucv.h
As reported by codespell.
Cc: Alexandra Winter <wintera@linux.ibm.com>
Cc: Thorsten Winkler <twinkler@linux.ibm.com>
Signed-off-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20240822-net-spell-v1-2-3a98971ce2d2@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for dumping PA stats registers via ethtool.
Firmware maintained stats are stored at PA Stats registers.
Also modify emac_get_strings() API to use ethtool_puts().
This commit also maintains consistency between miig_stats and pa_stats by
- renaming the array icssg_all_stats to icssg_all_miig_stats
- renaming the structure icssg_stats to icssg_miig_stats
- renaming ICSSG_STATS() to ICSSG_MIIG_STATS()
- changing order of stats related data structures and arrays so that data
structures of a certain stats type is clubbed together.
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20240822122652.1071801-3-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add documentation for pa-stats node which is syscon regmap for
PA_STATS registers. This will be used to dump statistics maintained by
ICSSG firmware.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: MD Danish Anwar <danishanwar@ti.com>
Link: https://patch.msgid.link/20240822122652.1071801-2-danishanwar@ti.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Oleksij Rempel says:
====================
Add ALCD Support to Cable Testing Interface
This patch series introduces support for Active Link Cable Diagnostics
(ALCD) in the ethtool cable testing interface and the DP83TD510 PHY
driver.
Why ALCD?
On a 10BaseT1L interface, TDR (Time Domain Reflectometry) is not
possible if the link partner is active - TDR will fail in these cases
because it requires interrupting the link. Since the link is active, we
already know the cable is functioning, so instead of using TDR, we can
use ALCD.
ALCD lets us measure cable length without disrupting the active link,
which is crucial in environments where network uptime is important. It
provides a way to gather diagnostic data without the need for downtime.
What's in this series:
- Extended the ethtool cable testing interface to specify the source of
diagnostic results (TDR or ALCD).
- Updated the DP83TD510 PHY driver to use ALCD when the link is
active, ensuring we can still get cable length info without dropping the
connection.
====================
Link: https://patch.msgid.link/20240822120703.1393130-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In industrial environments where 10BaseT1L PHYs are replacing existing
field bus systems like CAN, it's often essential to retain the existing
cable infrastructure. After installation, collecting metrics such as
cable length is crucial for assessing the quality of the infrastructure.
Traditionally, TDR (Time Domain Reflectometry) is used for this purpose.
However, TDR requires interrupting the link, and if the link partner
remains active, the TDR measurement will fail.
Unlike multi-pair systems, where TDR can be attempted during the MDI-X
switching window, 10BaseT1L systems face greater challenges. The TDR
sequence on 10BaseT1L is longer and coincides with uninterrupted
autonegotiation pulses, making TDR impossible when the link partner is
active.
The DP83TD510 PHY provides an alternative through ALCD (Active Link
Cable Diagnostics), which allows for cable length measurement without
disrupting an active link. Since a live link indicates no short or open
cable states, ALCD can be used effectively to gather cable length
information.
Enhance the dp83td510 driver by:
- Leveraging ALCD to measure cable length when the link is active.
- Bypassing TDR when a link is detected, as ALCD provides the required
information without disruption.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240822120703.1393130-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enhance the ethtool cable test interface by introducing the ability to
specify the source of the diagnostic information for cable test results.
This is particularly useful for PHYs that offer multiple diagnostic
methods, such as Time Domain Reflectometry (TDR) and Active Link Cable
Diagnostic (ALCD).
Key changes:
- Added `ethnl_cable_test_result_with_src` and
`ethnl_cable_test_fault_length_with_src` functions to allow specifying
the information source when reporting cable test results.
- Updated existing `ethnl_cable_test_result` and
`ethnl_cable_test_fault_length` functions to use TDR as the default
source, ensuring backward compatibility.
- Modified the UAPI to support these new attributes, enabling drivers to
provide more detailed diagnostic information.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240822120703.1393130-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Extend the ethtool netlink cable testing interface by adding support for
specifying the source of cable testing results. This allows users to
differentiate between results obtained through different diagnostic
methods.
For example, some TI 10BaseT1L PHYs provide two variants of cable
diagnostics: Time Domain Reflectometry (TDR) and Active Link Cable
Diagnostic (ALCD). By introducing `ETHTOOL_A_CABLE_RESULT_SRC` and
`ETHTOOL_A_CABLE_FAULT_LENGTH_SRC` attributes, this update enables
drivers to indicate whether the result was derived from TDR or ALCD,
improving the clarity and utility of diagnostic information.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20240822120703.1393130-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Adds a selftest that creates two virtual interfaces, assigns one to a
new namespace, and assigns IP addresses to both.
It listens on the destination interface using socat and configures a
dynamic target on netconsole, pointing to the destination IP address.
The test then checks if the message was received properly on the
destination interface.
Signed-off-by: Breno Leitao <leitao@debian.org>
Acked-by: Matthieu Baerts (NGI0) <matttbe@kernel.org>
Link: https://patch.msgid.link/20240822095652.3806208-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Breno Leitao says:
====================
netconsole: Populate dynamic entry even if netpoll fails
The current implementation of netconsole removes the entry and fails
entirely if netpoll fails to initialize. This approach is suboptimal, as
it prevents reconfiguration or re-enabling of the target through
configfs.
While this issue might seem minor if it were rare, it actually occurs
frequently when the network module is configured as a loadable module.
In such cases, the network is unavailable when netconsole initializes,
causing netpoll to fail. This failure forces users to reconfigure the
target from scratch, discarding any settings provided via the command
line.
The proposed change would keep the target available in configfs, albeit
in a disabled state. This modification allows users to adjust settings
or simply re-enable the target once the network module has loaded,
providing a more flexible and user-friendly solution.
v2: https://lore.kernel.org/20240819103616.2260006-1-leitao@debian.org
v1: https://lore.kernel.org/20240809161935.3129104-1-leitao@debian.org
====================
Link: https://patch.msgid.link/20240822111051.179850-1-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Currently, netconsole discards targets that fail during initialization,
causing two issues:
1) Inconsistency between target list and configfs entries
* user pass cmdline0, cmdline1. If cmdline0 fails, then cmdline1
becomes cmdline0 in configfs.
2) Inability to manage failed targets from userspace
* If user pass a target that fails with netpoll (interface not loaded at
netcons initialization time, such as interface is a module), then
the target will not exist in the configfs, so, user cannot re-enable
or modify it from userspace.
Failed targets are now added to the target list and configfs, but
remain disabled until manually enabled or reconfigured. This change does
not change the behaviour if CONFIG_NETCONSOLE_DYNAMIC is not set.
CC: Aijay Adams <aijay@meta.com>
Signed-off-by: Breno Leitao <leitao@debian.org>
Link: https://patch.msgid.link/20240822111051.179850-3-leitao@debian.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
