This is due to the slave_configuration routine is getting called when
host reset is active, and config page reads are failing, and driver
attempts to added device with stale config data.
To fix the issue, added error checking in slave_configure to check
for configuration pages failing, and return "1" so the device is
not configured. The config pages are failing if raid volume is
configured while issuing a host reset, thus driver is reading stale
data and proceeding to attempt to add. The fix is to return error
so the volume is not configured.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is due to driver reporting a device missing to the OS then the OS sending
a SYNC_CACHE request to driver while the IO queues are locked due to host reset.
To fix the issue, the driver will be waking up the port enable context
immediately when the driver receives the reply message, instead of waiting
on the hot plug worker threads.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for dead lock occurring between host_lock and sas_device_lock.
The deadlock is between two spin locks, between the shost->host_lock
and driver ioc->sas_device_lock.
The fix is to rearrange the code in the FW/Driver device removal
handshake so the ioc->sas_device_lock is not occurring when the
shost->host_lock is taken.
[jejb: zero initialise sas_address to fix spurious compiler warning]
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fix is in the driver-firmware handshake device removal code. We
need to read the controller ioc_state to see if controller is OPERATIONAL
prior to sending target reset and OP_REMOVE. Previously it was checking
the flag ioc->shost_recovery flag, which is always set when host reset is
active, thus preventing drives from getting properly deleted.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The fix is to inhibit the warning message in _scsih_get_sas_address
when the MPI2_IOCSTATUS_CONFIG_INVALID_PAGE ioc status is returned.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for issue : While discovery is in progress, hot unplug and hot plug of
enclosure connected to the controller card is causing system to hang.
When a device is in the process of being detected at driver load time then
if it is removed, the device that is no longer present will not be added
to the list. So the code in _scsih_probe_sas() is rearranged as such so
the devices that failed to be detected are not added to the list.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
New feature Fast Load Support.
(1)Asynchronous SCSI scanning: This will allow the drivers to scan
for devices in parallel while other device drivers are loading at
the same time. This will improve the amount of time it takes for the
OS to load.
(2) Reporting Devices while port enable is active: This feature will
allow devices to be reported to OS immediately while port enable is
active. The previous implementation waits for port enable to complete,
and then report devices. This feature is only enabled on IT firmware
configurations when there are no boot device configured in BIOS Configuration
Utility, else the driver will wait till port enable completes reporting
devices. For IR firmware, this feature is turned off. This feature is to
address large SAS topologies (>100 drives) when the boot OS is using onboard
SATA device, in other words, the boot devices is not
connected to our controller.
(3) Scanning for devices after diagnostic reset completes: A new routine
_scsih_scan_start is added. This will scan the expander pages, IR pages,
and sas device pages, then reporting new devices to SCSI Mid layer. It
seems the driver is not supporting adding devices while diagnostic reset
is active. Apparently this is due to the sanity checks on
ioc->shost_recovery flag throughout the context of kernel work thread FIFO,
and the mpt2sas_fw_work.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
1)Added ProxyVF_ID field to Configuration Request message.
2)Added IO Unit Page 8, IO Unit Page 9,and IO Unit Page 10.
3)Added SASNotifyPrimitiveMasks field to IOC Page 7.
4)Added SAS NOTIFY Primitive event.
5)Added Temperature Threshold Event.
6)Added Host Message Event.
7)Added Send Host Message request and reply.
Signed-off-by: Nagalakshmi Nandigama <nagalakshmi.nandigama@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
* 'for-linus' of git://ceph.newdream.net/git/ceph-client:
libceph: fix double-free of page vector
ceph: fix 32-bit ino numbers
libceph: force resend of osd requests if we skip an osdmap
ceph: use kernel DNS resolver
ceph: fix ceph_monc_init memory leak
ceph: let the set_layout ioctl set single traits
Revert "ceph: don't truncate dirty pages in invalidate work thread"
ceph: replace leading spaces with tabs
libceph: warn on msg allocation failures
libceph: don't complain on msgpool alloc failures
libceph: always preallocate mon connection
libceph: create messenger with client
ceph: document ioctls
ceph: implement (optional) max read size
ceph: rename rsize -> rasize
ceph: make readpages fully async
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (549 commits)
ALSA: hda - Fix ADC input-amp handling for Cx20549 codec
ALSA: hda - Keep EAPD turned on for old Conexant chips
ALSA: hda/realtek - Fix missing volume controls with ALC260
ASoC: wm8940: Properly set codec->dapm.bias_level
ALSA: hda - Fix pin-config for ASUS W90V
ALSA: hda - Fix surround/CLFE headphone and speaker pins order
ALSA: hda - Fix typo
ALSA: Update the sound git tree URL
ALSA: HDA: Add new revision for ALC662
ASoC: max98095: Convert codec->hw_write to snd_soc_write
ASoC: keep pointer to resource so it can be freed
ASoC: sgtl5000: Fix wrong mask in some snd_soc_update_bits calls
ASoC: wm8996: Fix wrong mask for setting WM8996_AIF_CLOCKING_2
ASoC: da7210: Add support for line out and DAC
ASoC: da7210: Add support for DAPM
ALSA: hda/realtek - Fix DAC assignments of multiple speakers
ASoC: Use SGTL5000_LINREG_VDDD_MASK instead of hardcoded mask value
ASoC: Set sgtl5000->ldo in ldo_regulator_register
ASoC: wm8996: Use SND_SOC_DAPM_AIF_OUT for AIF2 Capture
ASoC: wm8994: Use SND_SOC_DAPM_AIF_OUT for AIF3 Capture
...
* 'next-rebase' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci:
PCI: Clean-up MPS debug output
pci: Clamp pcie_set_readrq() when using "performance" settings
PCI: enable MPS "performance" setting to properly handle bridge MPS
PCI: Workaround for Intel MPS errata
PCI: Add support for PASID capability
PCI: Add implementation for PRI capability
PCI: Export ATS functions to modules
PCI: Move ATS implementation into own file
PCI / PM: Remove unnecessary error variable from acpi_dev_run_wake()
PCI hotplug: acpiphp: Prevent deadlock on PCI-to-PCI bridge remove
PCI / PM: Extend PME polling to all PCI devices
PCI quirk: mmc: Always check for lower base frequency quirk for Ricoh 1180:e823
PCI: Make pci_setup_bridge() non-static for use by arch code
x86: constify PCI raw ops structures
PCI: Add quirk for known incorrect MPSS
PCI: Add Solarflare vendor ID and SFC4000 device IDs
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (83 commits)
mmc: fix compile error when CONFIG_BLOCK is not enabled
mmc: core: Cleanup eMMC4.5 conditionals
mmc: omap_hsmmc: if multiblock reads are broken, disable them
mmc: core: add workaround for controllers with broken multiblock reads
mmc: core: Prevent too long response times for suspend
mmc: recognise SDIO cards with SDIO_CCCR_REV 3.00
mmc: sd: Handle SD3.0 cards not supporting UHS-I bus speed mode
mmc: core: support HPI send command
mmc: core: Add cache control for eMMC4.5 device
mmc: core: Modify the timeout value for writing power class
mmc: core: new discard feature support at eMMC v4.5
mmc: core: mmc sanitize feature support for v4.5
mmc: dw_mmc: modify DATA register offset
mmc: sdhci-pci: add flag for devices that can support runtime PM
mmc: omap_hsmmc: ensure pbias configuration is always done
mmc: core: Add Power Off Notify Feature eMMC 4.5
mmc: sdhci-s3c: fix potential NULL dereference
mmc: replace printk with appropriate display macro
mmc: core: Add default timeout value for CMD6
mmc: sdhci-pci: add runtime pm support
...
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/hch/vfs-queue: (21 commits)
leases: fix write-open/read-lease race
nfs: drop unnecessary locking in llseek
ext4: replace cut'n'pasted llseek code with generic_file_llseek_size
vfs: add generic_file_llseek_size
vfs: do (nearly) lockless generic_file_llseek
direct-io: merge direct_io_walker into __blockdev_direct_IO
direct-io: inline the complete submission path
direct-io: separate map_bh from dio
direct-io: use a slab cache for struct dio
direct-io: rearrange fields in dio/dio_submit to avoid holes
direct-io: fix a wrong comment
direct-io: separate fields only used in the submission path from struct dio
vfs: fix spinning prevention in prune_icache_sb
vfs: add a comment to inode_permission()
vfs: pass all mask flags check_acl and posix_acl_permission
vfs: add hex format for MAY_* flag values
vfs: indicate that the permission functions take all the MAY_* flags
compat: sync compat_stats with statfs.
vfs: add "device" tag to /proc/self/mountstats
cleanup: vfs: small comment fix for block_invalidatepage
...
Fix up trivial conflict in fs/gfs2/file.c (llseek changes)
* http://sucs.org/~rohan/git/gfs2-3.0-nmw: (24 commits)
GFS2: Move readahead of metadata during deallocation into its own function
GFS2: Remove two unused variables
GFS2: Misc fixes
GFS2: rewrite fallocate code to write blocks directly
GFS2: speed up delete/unlink performance for large files
GFS2: Fix off-by-one in gfs2_blk2rgrpd
GFS2: Clean up ->page_mkwrite
GFS2: Correctly set goal block after allocation
GFS2: Fix AIL flush issue during fsync
GFS2: Use cached rgrp in gfs2_rlist_add()
GFS2: Call do_strip() directly from recursive_scan()
GFS2: Remove obsolete assert
GFS2: Cache the most recently used resource group in the inode
GFS2: Make resource groups "append only" during life of fs
GFS2: Use rbtree for resource groups and clean up bitmap buffer ref count scheme
GFS2: Fix lseek after SEEK_DATA, SEEK_HOLE have been added
GFS2: Clean up gfs2_create
GFS2: Use ->dirty_inode()
GFS2: Fix bug trap and journaled data fsync
GFS2: Fix inode allocation error path
...
* '3.2-without-smb2' of git://git.samba.org/sfrench/cifs-2.6: (52 commits)
Fix build break when freezer not configured
Add definition for share encryption
CIFS: Make cifs_push_locks send as many locks at once as possible
CIFS: Send as many mandatory unlock ranges at once as possible
CIFS: Implement caching mechanism for posix brlocks
CIFS: Implement caching mechanism for mandatory brlocks
CIFS: Fix DFS handling in cifs_get_file_info
CIFS: Fix error handling in cifs_readv_complete
[CIFS] Fixup trivial checkpatch warning
[CIFS] Show nostrictsync and noperm mount options in /proc/mounts
cifs, freezer: add wait_event_freezekillable and have cifs use it
cifs: allow cifs_max_pending to be readable under /sys/module/cifs/parameters
cifs: tune bdi.ra_pages in accordance with the rsize
cifs: allow for larger rsize= options and change defaults
cifs: convert cifs_readpages to use async reads
cifs: add cifs_async_readv
cifs: fix protocol definition for READ_RSP
cifs: add a callback function to receive the rest of the frame
cifs: break out 3rd receive phase into separate function
cifs: find mid earlier in receive codepath
...
* 'for-linus' of git://oss.sgi.com/xfs/xfs: (69 commits)
xfs: add AIL pushing tracepoints
xfs: put in missed fix for merge problem
xfs: do not flush data workqueues in xfs_flush_buftarg
xfs: remove XFS_bflush
xfs: remove xfs_buf_target_name
xfs: use xfs_ioerror_alert in xfs_buf_iodone_callbacks
xfs: clean up xfs_ioerror_alert
xfs: clean up buffer allocation
xfs: remove buffers from the delwri list in xfs_buf_stale
xfs: remove XFS_BUF_STALE and XFS_BUF_SUPER_STALE
xfs: remove XFS_BUF_SET_VTYPE and XFS_BUF_SET_VTYPE_REF
xfs: remove XFS_BUF_FINISH_IOWAIT
xfs: remove xfs_get_buftarg_list
xfs: fix buffer flushing during unmount
xfs: optimize fsync on directories
xfs: reduce the number of log forces from tail pushing
xfs: Don't allocate new buffers on every call to _xfs_buf_find
xfs: simplify xfs_trans_ijoin* again
xfs: unlock the inode before log force in xfs_change_file_space
xfs: unlock the inode before log force in xfs_fs_nfs_commit_metadata
...
In setlease, we use i_writecount to decide whether we can give out a
read lease.
In open, we break leases before incrementing i_writecount.
There is therefore a window between the break lease and the i_writecount
increment when setlease could add a new read lease.
This would leave us with a simultaneous write open and read lease, which
shouldn't happen.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This makes NFS follow the standard generic_file_llseek locking scheme.
Cc: Trond.Myklebust@netapp.com
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This gives ext4 the benefits of unlocked llseek.
Cc: tytso@mit.edu
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add a generic_file_llseek variant to the VFS that allows passing in
the maximum file size of the file system, instead of always
using maxbytes from the superblock.
This can be used to eliminate some cut'n'paste seek code in ext4.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
The i_mutex lock use of generic _file_llseek hurts. Independent processes
accessing the same file synchronize over a single lock, even though
they have no need for synchronization at all.
Under high utilization this can cause llseek to scale very poorly on larger
systems.
This patch does some rethinking of the llseek locking model:
First the 64bit f_pos is not necessarily atomic without locks
on 32bit systems. This can already cause races with read() today.
This was discussed on linux-kernel in the past and deemed acceptable.
The patch does not change that.
Let's look at the different seek variants:
SEEK_SET: Doesn't really need any locking.
If there's a race one writer wins, the other loses.
For 32bit the non atomic update races against read()
stay the same. Without a lock they can also happen
against write() now. The read() race was deemed
acceptable in past discussions, and I think if it's
ok for read it's ok for write too.
=> Don't need a lock.
SEEK_END: This behaves like SEEK_SET plus it reads
the maximum size too. Reading the maximum size would have the
32bit atomic problem. But luckily we already have a way to read
the maximum size without locking (i_size_read), so we
can just use that instead.
Without i_mutex there is no synchronization with write() anymore,
however since the write() update is atomic on 64bit it just behaves
like another racy SEEK_SET. On non atomic 32bit it's the same
as SEEK_SET.
=> Don't need a lock, but need to use i_size_read()
SEEK_CUR: This has a read-modify-write race window
on the same file. One could argue that any application
doing unsynchronized seeks on the same file is already broken.
But for the sake of not adding a regression here I'm
using the file->f_lock to synchronize this. Using this
lock is much better than the inode mutex because it doesn't
synchronize between processes.
=> So still need a lock, but can use a f_lock.
This patch implements this new scheme in generic_file_llseek.
I dropped generic_file_llseek_unlocked and changed all callers.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This doesn't change anything for the compiler, but hch thought it would
make the code clearer.
I moved the reference counting into its own little inline.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Add inlines to all the submission path functions. While this increases
code size it also gives gcc a lot of optimization opportunities
in this critical hotpath.
In particular -- together with some other changes -- this
allows gcc to get rid of the unnecessary clearing of
sdio at the beginning and optimize the messy parameter passing.
Any non inlining of a function which takes a sdio parameter
would break this optimization because they cannot be done if the
address of a structure is taken.
Note that benefits are only seen with CONFIG_OPTIMIZE_INLINING
and CONFIG_CC_OPTIMIZE_FOR_SIZE both set to off.
This gives about 2.2% improvement on a large database benchmark
with a high IOPS rate.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Only a single b_private field in the map_bh buffer head is needed after
the submission path. Move map_bh separately to avoid storing
this information in the long term slab.
This avoids the weird 104 byte hole in struct dio_submit which also needed
to be memseted early.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
A direct slab call is slightly faster than kmalloc and can be better cached
per CPU. It also avoids rounding to the next kmalloc slab.
In addition this enforces cache line alignment for struct dio to avoid
any false sharing.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fix most problems reported by pahole.
There is still a weird 104 byte hole after map_bh. I'm not sure what
causes this.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
There's nothing on the stack, even before my changes.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This large, but largely mechanic, patch moves all fields in struct dio
that are only used in the submission path into a separate on stack
data structure. This has the advantage that the memory is very likely
cache hot, which is not guaranteed for memory fresh out of kmalloc.
This also gives gcc more optimization potential because it can easier
determine that there are no external aliases for these variables.
The sdio initialization is a initialization now instead of memset.
This allows gcc to break sdio into individual fields and optimize
away unnecessary zeroing (after all the functions are inlined)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We need to move the inode to the end of the list to actually make the
spinning prevention explained in the comment above it work. With a
plain list_move it will simply stay in place as we're always reclaiming
from the head of the list.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruen@kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruen@kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
We are going to add more flags and having them in hex format
make it simpler
Acked-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: J. Bruce Fields <bfields@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruen@kernel.org>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
This was found by inspection while tracking a similar
bug in compat_statfs64, that has been fixed in mainline
since decemeber.
- This fixes a bug where not all of the f_spare fields
were cleared on mips and s390.
- Add the f_flags field to struct compat_statfs
- Copy f_flags to userspace in case someone cares.
- Use __clear_user to copy the f_spare field to userspace
to ensure that all of the elements of f_spare are cleared.
On some architectures f_spare is has 5 ints and on some
architectures f_spare only has 4 ints. Which makes
the previous technique of clearing each int individually
broken.
I don't expect anyone actually uses the old statfs system
call anymore but if they do let them benefit from having
the compat and the native version working the same.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
* 'drm-core-next' of git://people.freedesktop.org/~airlied/linux: (290 commits)
Revert "drm/ttm: add a way to bo_wait for either the last read or last write"
Revert "drm/radeon/kms: add a new gem_wait ioctl with read/write flags"
vmwgfx: Don't pass unused arguments to do_dirty functions
vmwgfx: Emulate depth 32 framebuffers
drm/radeon: Lower the severity of the radeon lockup messages.
drm/i915/dp: Fix eDP on PCH DP on CPT/PPT
drm/i915/dp: Introduce is_cpu_edp()
drm/i915: use correct SPD type value
drm/i915: fix ILK+ infoframe support
drm/i915: add DP test request handling
drm/i915: read full receiver capability field during DP hot plug
drm/i915/dp: Remove eDP special cases from bandwidth checks
drm/i915/dp: Fix the math in intel_dp_link_required
drm/i915/panel: Always record the backlight level again (but cleverly)
i915: Move i915_read/write out of line
drm/i915: remove transcoder PLL mashing from mode_set per specs
drm/i915: if transcoder disable fails, say which
drm/i915: set watermarks for third pipe on IVB
drm/i915: export a CPT mode set verification function
drm/i915: fix transcoder PLL select masking
...
* 'x86-vdso-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86-64, doc: Remove int 0xcc from entry_64.S documentation
x86, vsyscall: Add missing <asm/fixmap.h> to arch/x86/mm/fault.c
Fix up trivial conflicts in arch/x86/mm/fault.c (asm/fixmap.h vs
asm/vsyscall.h: both work, which to use? Whatever..)
* 'x86-spinlocks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, ticketlock: remove obsolete comment
x86, cmpxchg: Use __compiletime_error() to make usage messages a bit nicer
x86, ticketlock: Make __ticket_spin_trylock common
x86, ticketlock: Convert __ticket_spin_lock to use xadd()
x86, ticketlock: Convert spin loop to C
x86, ticketlock: Clean up types and accessors
x86: Use xadd helper more widely
x86: Add xadd helper macro
x86, cmpxchg: Unify cmpxchg into cmpxchg.h
x86, cmpxchg: Move 64-bit set64_bit() to match 32-bit
x86, cmpxchg: Move 32-bit __cmpxchg_wrong_size to match 64 bit.
x86, cmpxchg: <linux/alternative.h> has LOCK_PREFIX
* 'x86-rdrand-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, random: Verify RDRAND functionality and allow it to be disabled
x86, random: Architectural inlines to get random integers with RDRAND
random: Add support for architectural random hooks
Fix up trivial conflicts in drivers/char/random.c: the architectural
random hooks touched "get_random_int()" that was simplified to use MD5
and not do the keyptr thing any more (see commit 6e5714eaf7: "net:
Compute protocol sequence numbers and fragment IDs using MD5").
* 'x86-microcode-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, microcode, AMD: Add microcode revision to /proc/cpuinfo
x86, microcode: Correct microcode revision format
coretemp: Get microcode revision from cpu_data
x86, intel: Use c->microcode for Atom errata check
x86, intel: Output microcode revision in /proc/cpuinfo
x86, microcode: Don't request microcode from userspace unnecessarily
Fix up trivial conflicts in arch/x86/kernel/cpu/amd.c (conflict between
moving AMD BSP code to cpu_dev helper function and adding AMD microcode
revision to /proc/cpuinfo code)
* 'x86-hyperv-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Hyper-V: Integrate the clocksource with Hyper-V detection code
Fix up conflicts in drivers/staging/hv/Makefile manually (some of the hv
code has moved out of staging to drivers/hv/)
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, amd: Include linux/elf.h since we use stuff from asm/elf.h
x86: cache_info: Update calculation of AMD L3 cache indices
x86: cache_info: Kill the atomic allocation in amd_init_l3_cache()
x86: cache_info: Kill the moronic shadow struct
x86: cache_info: Remove bogus free of amd_l3_cache data
x86, amd: Include elf.h explicitly, prepare the code for the module.h split
x86-32, amd: Move va_align definition to unbreak 32-bit build
x86, amd: Move BSP code to cpu_dev helper
x86: Add a BSP cpu_dev helper
x86, amd: Avoid cache aliasing penalties on AMD family 15h
nfsiostat was failing to find mounted filesystems on kernels after
2.6.38 because of changes to show_vfsstat() by commit
c7f404b40a. This patch adds back the
"device" tag before the nfs server entry so scripts can parse the
mountstats file correctly.
Signed-off-by: Bryan Schumaker <bjschuma@netapp.com>
CC: stable@kernel.org [>=2.6.39]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Currently, when you call iov_iter_advance, then the pointer to the iovec
array can be incremented, but it does not decrement the nr_segs value in
the iov_iter struct. The result is a iov_iter struct with a nr_segs
value that goes beyond the end of the array.
While I'm not aware of anything that's specifically broken by this, it
seems odd and a bit dangerous not to decrement that value. If someone
were to trust the nr_segs value to be correct, then they could end up
walking off the end of the array.
Changing this might also provide some micro-optimization when dealing
with the last iovec in an array. Many of the other routines that deal
with iov_iter have optimized codepaths when nr_segs == 1.
Cc: Nick Piggin <npiggin@suse.de>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
fs/cifs/transport.c: In function 'wait_for_response':
fs/cifs/transport.c:328: error: implicit declaration of function 'wait_event_freezekillable'
Caused by commit f06ac72e92 ("cifs, freezer: add
wait_event_freezekillable and have cifs use it"). In this config,
CONFIG_FREEZER is not set.
Reviewed-by: Shirish Pargaonkar <shirishp@us.ibm.com>
CC: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <smfrench@gmail.com>
