The current 85xxCDS restart code fails to reset the PCI bus which can
lead to odd behavior after the restart. This patch uses the VIA Super
Southbridge to perform a PCI reset which will reset the entire system.
NOTE: Since the VIA chip is behind a PCI-to-PCI bridge which can be
disabled with a switch setting, it may not be possible to perform the
PCI bus reset. In this case, the code defaults to the previous restart
mechanism.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The Freescale MPC8555CDS and MPC8548CDS reference hardware has a legacy
8259 interrupt controller pair contained within a VIA VT82C686B Southbridge
on the main carrier board. The processor complex plugs into the carrier
card using a PCI slot which limits the available interrupts to the
INTA-INTD PCI interrupts. The output of the 8259 cascade pair is routed
through a gate array and connected to the PCI INTA interrupt line.
The normal interrupt chaining hook (set_irq_chained_handler) does
not allow sharing of the chained interrupt which prevents the
use of PCI INTA by PCI devices. This patch allows the 8259 cascade
pair to share their interrupt line with PCI devices.
NOTE: The addition of the .end routine for the MPIC is not strictly
necessary for this patch. It's there so this code will run from within
the threaded interrupt context used by the Real Time patch.
Signed-off-by: Randy Vinson <rvinson@mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some set of 85xx platforms have PCI-X controllers. The old arch/ppc
code setup these controllers and we haven't moved it over to arch/powerpc.
We use the PCI-X Capabilties to know if we are in PCI-X mode instead
of the Global Utilities PORDEVSR.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
For the Freescale PCIe PHBs Not all firmwares setup the virtual P2P
bridge registers properly. Make sure they get setup based on what
the struct pci_controller got from the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We need the ability to set P2P bridge registers to properly setup the virtual
P2P bridges that exist in PCIe controllers for some of the embedded setups.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add basic support for the PCIe PHB and enable the ULI bridge.
Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Make it so we do a runtime check to know if we need to write cfg_addr
as big or little endian. This is needed if we want to allow 86xx support
to co-exist in the same kernel as other 6xx PPCs.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
We don't use setup_indirect_pci_nomap in arch/powerpc and it appears
the users that needed it from arch/ppc are now using setup_indirect_pci.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The newer Arcadia boards for CDS have an FPGA that shows up on PCI
however isn't a real PCI device. Add a quirk to just ignore the
FPGA.
This is based on the following patch from Andy & York:
http://ozlabs.org/pipermail/linuxppc-dev/2007-February/032042.html
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
On the 85xx/86xx PCIe controllers if there is no device connected to the
PHB we will still allocate a pci_bus for downstream bus of the virtual
P2P bridge. However the resources allocated to the downstream bus are not
correct and so we just mimic the resources from the upstream pci_bus.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Switch the 85xx platform over to using the FSL generic PCI code. This
gets ups PCIe support in addition to base PCI support.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Updated the 83xx & 85xx device tree PCI related compartible property.
Used the following compatible properties:
PCI "fsl,mpc8349-pci"
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add 8548 CDS PCI express controller node and PCI-X device node. The current
dts file is suitable for 8548 Rev 2.0 board with Arcadia 3.1.
This kind of board combination is the most popular.
Used the following compatible properties:
PCI "fsl,mpc8540-pci"
PCI-X: "fsl,mpc8540-pcix"
PCIe: "fsl,mpc8548-pcie"
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use the PCI capabilities to determine if we are PCIe PHB. Also use
PPC_INDIRECT_TYPE_NO_PCIE_LINK since the Freescale PCIe controllers
will lock the system if they don't have link and you try to do a config
access to anything but the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added PPC_INDIRECT_TYPE_NO_PCIE_LINK flag to the indirect pci handling
code to ensure that we don't talk to any device other than the PHB
if we don't have PCIe link. Some controllers will lockup if they try
to do a config cycle to any device on the bus except the PHB.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Added early_find_capability that wraps pci_bus_find_capability and uses
fake_pci_bus() to allow us to call it before we've fully setup the
pci_controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Rewrite the Freescale PCI code to support PCI on 83xx/85xx/86xx and
PCIe on 85xx/86xx.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Move
arch/powerpc/platforms/86xx/pci.c -> arch/powerpc/sysdev/fsl_pci.c
arch/powerpc/sysdev/fsl_pcie.h -> arch/powerpc/sysdev/fsl_pci.h
as the base to unify 83xx/85xx/86xx pci and pcie.
Add CONFIG_FSL_PCI to build fsl_pci.c for Freescale pci and pcie option.
The code still works for 86xx platforms.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This avoids a conflict with sparse builds.
Reported by Alexey Dobriyan, fix suggested by Al Viro
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The recent 9p commit: bd238fb431 that
supposedly only moved files also introduced a new 9p sysctl interface
that did not properly register it's sysctl binary numbers.
And since it was only for debugging clearly did not need a binary fast
path in any case. So this patch just remove the binary numbers.
See Documentation/sysctl/ctl_unnumbered.txt for more details.
While I was at it I cleaned up the sysctl initializers a little as
well so there is less to read.
Cc: Latchesar Ionkov <lucho@ionkov.net>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a typo in SubmittingPatches where "probably" was spelt "probabally".
Signed-off-by: Linus Nilsson <lajnold@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change a headline to reflect that there are three main types of kernel
locking, not two.
Signed-off-by: Linus Nilsson <lajnold@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/ehca: Support small QP queues
IB/ehca: Make internal_create/destroy_qp() static
IB/ehca: Move ehca2ib_return_code() out of line
IB/ehca: Generate async event when SRQ limit reached
IB/ehca: Support large page MRs
IB/mlx4: Fix error path in create_qp_common()
mlx4_core: Change command token on timeout
IB/mthca: Change command token on timeout
IB/ipath: Remove ipath_layer dead code
IB/mlx4: Fix leaks in __mlx4_ib_modify_qp
Now that the last inlined instances are gone, all that is left to do
is turning disable_irq_nosync on arm26 and m68k from defines to aliases
and we are all set - we can make these externs in linux/interrupt.h
uncoditional and kill remaining instances in asm/irq.h
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not everyone wants libsas automatically to pull in libata. This patch
makes the behaviour configurable, so you can build libsas with or
without ATA support.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Convert from struct class_device to struct device
leds: leds-gpio for ngw100
leds: Add warning printks in error paths
leds: Fix trigger unregister_simple if register_simple fails
leds: Use menuconfig objects II - LED
leds: Teach leds-gpio to handle timer-unsafe GPIOs
leds: Add generic GPIO LED driver
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
leds: cr_bllcd.c: build fix
backlight: Convert from struct class_device to struct device
backlight: Fix order of Kconfig entries
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Clean up duplicate includes in drivers/macintosh/
[POWERPC] Quiet section mismatch warning on pcibios_setup
[POWERPC] init and exit markings for hvc_iseries
[POWERPC] Quiet section mismatch in hvc_rtas.c
[POWERPC] Constify of_platform_driver match_table
[POWERPC] hvcs: Make some things static and const
[POWERPC] Constify of_platform_driver name
[POWERPC] MPIC protected sources
[POWERPC] of_detach_node()'s device node argument cannot be const
[POWERPC] Fix ARCH=ppc builds
[POWERPC] mv64x60: Use mutex instead of semaphore
[POWERPC] Allow smp_call_function_single() to current cpu
[POWERPC] Allow exec faults on readable areas on classic 32-bit PowerPC
[POWERPC] Fix future firmware feature fixups function failure
[POWERPC] fix showing xmon help
[POWERPC] Make xmon_write accept a const buffer
[POWERPC] Fix misspelled "CONFIG_CHECK_CACHE_COHERENCY" Kconfig option.
[POWERPC] cell: CONFIG_SPE_BASE is a typo
Obviously broken on little-endian; fortunately, the option is not
frequently used...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
[ Hey, sparse is wonderful, but even better than sparse is having people
like Al that actually _run_ it and fix bugs using it. - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (77 commits)
ACPI: Populate /sys/firmware/acpi/tables/
ACPI: create CONFIG_ACPI_DEBUG_FUNC_TRACE
ACPI: update ACPI proc I/F removal schedule
ACPI: update feature-removal-schedule.txt, /sys/firmware/acpi/namespace is gone
ACPI: export ACPI events via acpi_mc_group multicast group
ACPI: fix empty macros found by -Wextra
ACPI: drivers/acpi/pci_link.c: lower printk severity
sony-laptop: Fix event reading in sony-laptop
sony-laptop: Add Vaio FE to the special init sequence
sony-laptop: Make the driver use MSC_SCAN and a setkeycode and getkeycode key table.
sony-laptop: Invoke _INI for SNC devices that provide it
sony-laptop: Add support for recent Vaios Fn keys (C series for now)
sony-laptop: map wireless switch events to KEY_WLAN
sony-laptop: add new SNC handlers
ACPI: thinkpad-acpi: add locking to brightness subdriver
ACPI: thinkpad-acpi: bump up version to 0.15
ACPI: thinkpad-acpi: make EC-based thermal readings non-experimental
ACPI: thinkpad-acpi: make sure DSDT TMPx readings don't return +128
ACPI: thinkpad-acpi: react to Lenovo ThinkPad differences in hot key
ACPI: thinkpad-acpi: allow use of CMOS NVRAM for brightness control
...
They are identical
Indirectly pointed out by Thomas Gleixner
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get rid of warnings like
WARNING: vmlinux.o(.bootstrap.text+0x1a8): Section mismatch: reference to .init.text:x86_64_start_kernel (between 'initial_code' and 'init_rsp')
- Move initialization code into .text.head like i386 because modpost knows about this already
- Mark initial_code .initdata
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warning:
WARNING: vmlinux.o(.text+0x188ea): Section mismatch: reference to .init.text:__alloc_bootmem_core (between 'alloc_bootmem_high_node' and 'get_gate_vma')
alloc_bootmem_high_node() is only used from __init scope so declare it __init.
And in addition declare the weak variant __init too.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix following warnings:
WARNING: vmlinux.o(.text+0x945e): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
WARNING: vmlinux.o(.text+0x9474): Section mismatch: reference to .init.text:__set_fixmap (between 'hpet_arch_init' and 'hpet_mask_rtc_irq_bit')
hpet_arch_init is only used from __init context so mark it __init.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The performance counters on K7 are only 48 bits wide, so using bit 63 to
check if the counter overflowed is wrong. Let's use bit 47 instead.
Signed-off-by: Björn Steinbrink <B.Steinbrink@gmx.de>
Cc: Don Zickus <dzickus@redhat.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Previously lock was unconditionally used, but shouldn't be needed on
UP systems.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I got an oops while booting a 32bit kernel on KVM because it doesn't
implement performance counters used by the NMI watchdog. Handle this
case.
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to index register access ordering problems, when using macros a line
like this fails (and does nothing):
setCx86(CX86_CCR2, getCx86(CX86_CCR2) | 0x88);
With inlined functions this line will work as expected.
Note about a side effect: Seems on Geode GX1 based systems the
"suspend on halt power saving feature" was never enabled due to this
wrong macro expansion. With inlined functions it will be enabled, but
this will stop the TSC when the CPU runs into a HLT instruction.
Kernel output something like this:
Clocksource tsc unstable (delta = -472746897 ns)
This is the 3rd version of this patch.
- Adding missed arch/i386/kernel/cpu/mtrr/state.c
Thanks to Andres Salomon
- Adding some big fat comments into the new header file
Suggested by Andi Kleen
AK: fixed x86-64 compilation
Signed-off-by: Juergen Beisert <juergen@kreuzholzen.de>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
local_cmpxchg() should not use any LOCK prefix. This change probably
got lost in the move to cmpxchg.h.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kstat_irqs(0) includes the count of interrupt 0 from all cpus, not just
the current cpu. The updated interrupt 0 on other cpus can stop the
nmi_watchdog from tripping, so only include the current cpu's int 0.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
