We've noticed that sometimes "MTD do_write_buffer(): software timeout"
message was printed out when writing to a Fujitsu NOR flash.
It turned out that this was because of a race in the timeout handling
do_write_buffer(). A small timeout of (HZ / 1000) + 1 is used there, and
sometimes if the timer interrupt handling takes more than one or even two
jiffies (which is 1-2 ms with HZ == 1000) and that interrupt happens just
after chip_ready() call, the driver bails out from a ready polling loop
despite the chip has actually become ready while all those interrupts were
handled. To deal with this issue, extra check for chip ready is neccessary on
timeout expiration (and the checks should better be reordered).
As do_write_oneword() uses the same approach, it needs to also be changed.
Signed-off-by: Konstantin Baidarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following patch adds support for the TQ Systems TQM834x Boards.
Verified on TQM8349L.
This is a resubmit after integrating the suggested changes.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix two compile warnings that occur because of treating two
'unsigned long's as 'void *'s.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The assignement of a "const char *" to a "char *" variable
is emitting a warning with gcc 4.0. We cannot change
mtd->name to "const char *" as we have dynamic assignements
of the name. So casting is the correct solution here
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Nathan Roberts noticed the nand_write_ecc index into oobbuf goes out of
bounds when crossing an erase block boundary, causing incorrect OOB data
to be written and corrupting memory. Reset the index to zero after
re-preparing oobbuf for a new erase block.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In case of an odd offset, the result was shifted by 1 instead of 8
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- Use map.virt instead of map.map_priv_1 since it has the correct type.
- Use readw/writew instead of dereferencing an ioremap'd cookie.
- Remove an unused variable.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The Sharp Zaurus akita and borzoi models are large page flash devices.
This patch adds support for them to the sharpsl MTD NAND driver but
keeps the oob layout and bad block positions compatible with the Sharp
Zaurus 2.4 kernel and ROM bootloader.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Change to the extended cfi table parsing for Intel NOR flash that uses
the info in the extended table to 'walk' the table rather than using
hard coding for various primary extended query table version numbers.
From: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some callers to block-layer commit_write function treat non-zero return as
error, notably the loopback mount driver sometimes used in conjunction with
JFFS2 on NAND flash for bad block avoidance, etc. Return zero for success
as do various other commit_write functions.
Signed-off-by: Todd Poynor <tpoynor@mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If they get inlined into non __xipram functions we're screwed.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added .owner initialisation to allow the
tracking of the device_driver owners when
built as a module
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner to device driver field for tracking
when loaded as a module.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Added owner fields to the device_driver for tracking
ownership when built as a module
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Don't assume eraseblock size is power of 2.
Dataflash can have aligned eraseblock size.
From: Peter Menzebach <pm-mtd@mw-itcon.de>
Acked-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- assume wbuf may be of size which is not power of 2
- don't make strange assumption about not padding wbuf for DataFlash
- use wbuf = DataFlash page and eraseblock >= 8 Dataflash pages
From: Peter Menzebach <pm-mtd@mw-itcon.de>
Acked-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add density mask for better support of DDP chips.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Simple bad block table source and header files
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
- cleaned up the partitions and include files
- added more flexible CS and address detection and setup
Regression tested on db1200 and db1550.
Signed-off-by: Pete Popov <ppopov@pacbell.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Simplify the debugging code further.
Update the TODO list
Signed-off-by: Artem B. Bityutskiy <dedekind@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add support for "4G Systems MTX-1 Flash device", better known as meshcube.
From: Bruno Randolf <bruno.randolf@4g-systems.biz>
Signed-off-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Always keep valid data in reserved_size.
It did not cause problems, but the reservation code was unoptimal
when centralized summary was active or the size of the erase block
was very small.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The changes introduced allow to suspend/resume NAND flash.
A new state (FL_PM_SUSPENDED) is introduced, as well as
routines for mtd->suspend and mtd->resume to put the flash in
suspended state from software pov.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Do the summary collection in the right place. If the device
was not writebuffered but had c->mtd->writev function
(e.g. blkmtd) the summary collector function was not called.
Signed-off-by: Ferenc Havasi <havasi@inf.u-szeged.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now we can use the generic platform driver
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
