commit bf56f0a666 (2.6.37-rc1), from Nishanth Menon attempted
to fix card detection for PandaBoard, unfortunately, the fix missed
to initialize .gpio_cd member of omap2_hsmmc_info. This results
in a default value of '0', which is a valid GPIO line.
On PandaBoard, the side effect of this is that GPIO line 0 controls
the powering TFP410 DVI chip, and without the fix DVI chip is
inadvertently powered.
Tested-by: David Anders <x0132446@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The display reset lines are connected to a TPS65930 which may sleep
when changing GPIO values. Use the appropriate function to silence
a nasty warning from gpiolib.
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Acked-by: Thomas Weber <weber@corscience.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cosmetic fixes to the code:
- white spaces and tabs,
- alignement,
- comments rephrase and typos,
- multi-line comments
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Errata covered:
- 1.157 & 1.185
- i443
- i581
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
- Reworked and simplified the execution paths for better
readability and to avoid duplication of code,
- Added comments on the entry and exit points and the interaction
with the ROM code for OFF mode restore,
- Reworked the existing comments for better readability.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Organize the code in the following sections:
- register access macros,
- API functions,
- internal functions.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Using macros from existing include files for registers addresses.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Based on original patch from Vishwa.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Vishwanath BS <vishwanath.bs@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The SRAM PA addresses are locally defined and used at
different places, i.e. SRAM management code and idle sleep code.
The macros are now defined at a centralized place, for
easier maintenance.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon<nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Remove unused code:
- macros,
- variables,
- unused semaphore locking API. This API shall be added back
when needed,
- infinite loops for debug.
Tested on N900 and Beagleboard with full RET and OFF modes,
using cpuidle and suspend.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon<nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Limitation i583: Self_Refresh Exit issue after OFF mode
Issue:
When device is waking up from OFF mode, then SDRC state machine sends
inappropriate sequence violating JEDEC standards.
Impact:
OMAP3630 < ES1.2 is impacted as follows depending on the platform:
CS0: for 38.4MHz as internal sysclk, DDR content seen to be stable, while
for all other sysclk frequencies, varied levels of instability
seen based on varied parameters.
CS1: impacted
This patch takes option #3 as recommended by the Silicon erratum:
Avoid core power domain transitioning to OFF mode. Power consumption
impact is expected in this case.
To do this, we route core OFF requests to RET request on the impacted
revisions of silicon.
Acked-by: Jean Pihet <j-pihet@ti.com>
[nm@ti.com: rebased the code to 2.6.37-rc2- short circuit code changed a bit]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently omap3_cpuidle_update_states makes whole sale decision
on which C states to update based on enable_off_mode variable
Instead, achieve the same functionality by independently providing
mpu and core deepest states the system is allowed to achieve and
update the idle states accordingly.
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[khilman: fixed additional user of this API in OMAP CPUidle driver]
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
While coming out of MPU OSWR/OFF states, L2 controller is reseted.
The reset behavior is implementation specific as per ARMv7 TRM and
hence $L2 needs to be invalidated before it's use. Since the
AUXCTRL register is also reconfigured, disable L2 cache before
invalidating it and re-enables it afterwards. This is as per
Cortex-A8 ARM documentation.
Currently this is identified as being needed on OMAP3630 as the
disable/enable is done from "public side" while, on OMAP3430, this
is done in the "secure side".
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[nm@ti.com: ported to 2.6.37-rc2, added hooks to enable the logic only on 3630]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Erratum id: i608
RTA (Retention Till Access) feature is not supported and leads to device
stability issues when enabled. This impacts modules with embedded memories
on OMAP3630
Workaround is to disable RTA on boot and coming out of core off.
For disabling RTA coming out of off mode, we do this by overriding the
restore pointer for 3630 as the first point of entry before caches are
touched and is common for GP and HS devices. To disable earlier than
this could be possible by modifying the PPA for HS devices, but not for
GP devices.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
[ambresh@ti.com: co-developer]
Signed-off-by: Ambresh K <ambresh@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Introduce errata handling for OMAP3. This patch introduces
errata variable and stub for initialization which will be
filled up by follow-on patches.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Erratum i581 impacts OMAP3 platforms.
PRCM DPLL control FSM removes SDRC_IDLEREQ before DPLL3 locks causing
the DPLL not to be locked at times.
IMPORTANT:
*) This is not a complete workaround implementation as recommended
by the silicon erratum. This is a support logic for detecting lockups and
attempting to recover where possible and is known to provide stability
in multiple platforms.
*) This code is mostly important for inactive and retention. The ROM code
waits for the maximum DLL lock time when resuming from off mode. So for
off mode this code isn't really needed.
*) counters are introduced here for eventual export to userspace once the
cleanups are completed.
This should eventually get refactored as part of cleanups to sleep34xx.S
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Peter 'p2' De Schrijver <peter.de-schrijver@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Analysis in TI kernel with ETM showed that using cache mapped flush
in kernel instead of SO mapped flush cost drops by 65% (3.39mS down
to 1.17mS) for clean_l2 which is used during sleep sequences.
Overall:
- speed up
- unfortunately there isn't a good alternative flush method today
- code reduction and less maintenance and potential bug in
unmaintained code
This also fixes the bug with the clean_l2 function usage.
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Jean Pihet <j-pihet@ti.com>
[nm@ti.com: ported rkw's proposal to 2.6.37-rc2]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
With new OPP layer, OPP users will access OPP API directly instead of
using OMAP PM layer, so remove all notions of OPPs from the OMAP PM
layer.
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Add OPP data for OMAP34xx and OMAP36xx and initialization functions
to populate OPP tables based on current SoC.
introduce an OMAP generic opp initialization routine which OMAP3
and OMAP4+ SoCs can use to register their OPP definitions.
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
omap2_common_pm_init is the API where generic system devices like
mpu, l3 etc get initialized. This has to happen really early on
during the boot and not at a later time. This is especially important
with the new opp changes as these devices need to be built before the
opp tables init happen. Today both are device initcalls and it works
just because of the order of compilation. Making this postcore_initcall
is ideal because the omap device layer init happens as a core_initcall
and typically rest of the driver/device inits are arch_initcall or
something lower.
Signed-off-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Some bad interaction between the idle and the suspend paths has been
identified: the idle code is called during the suspend enter and exit
sequences. This could cause corruption or lock-up of resources.
The solution is to move the calls to disable_hlt at the very beginning
of the suspend sequence (ex. in omap3_pm_begin instead of
omap3_pm_prepare), and the call to enable_hlt at the very end of
the suspend sequence (ex. in omap3_pm_end instead of omap3_pm_finish).
Tested with RET and OFF on Beagle and OMAP3EVM.
Signed-off-by: Jean Pihet <j-pihet@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
If the TPA6130 is compiled as module the id and power_gpio values are
arbitrary at module probing time since the rx51_tpa6130a2_data was marked as
__initdata. Fix this by using __initdata_or_module. Then __initdata is
defined only if the kernel is built without CONFIG_MODULES and omitted
otherwise.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
After commit ed919b0 "mmc: sdio: fix runtime PM anomalies by introducing
MMC_CAP_POWER_OFF_CARD" it is required to specify MMC_CAP_POWER_OFF_CARD
to have runtime PM support. As the wl1251 driver expects card to be
powered down when it's not used, wifi will no longer work after interface
is brought down at least once without functioning runtime PM.
Fix this by declaring MMC_CAP_POWER_OFF_CARD for MMC3.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds omap_reserve functionality to board-omap4panda.c.
Helps in the reserving boot time memory in SDRAM, used here for
framebuffer allocation.
This patch is in similar lines to commit id 71ee7dad9b, from
Russell king
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Raghuveer Murthy <raghuveer.murthy@ti.com>
[tony@atomide.com: fixed to be before .map_io as pointed out by Russell King]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Register BH1780GLI Ambient light sensor, which is an I2C device
for 4430SDP board.
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure the LED is turned off at boot time, and configure the GPIO LED
device as active low.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
gpio_direction_output() has a value argument, there's no need to call
gpio_set_value() explicitly right after.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 72f381ba05 (omap3: Remove VMMC2 regulator on IGEP v2)
removed an unused regulator entry, but left the second MMC channel
(used by the Libertas WLAN module) without link to power regulator.
This causes the SDIO module to fail being detected.
This patch adds the two regulators that actually feed the WLAN module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected. Details of the power supply
implementation were kindly provided by Enric Balletbo i Serra.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Tested on an IGEPv2 Rev-B.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Patch "OMAP2xxx: hwmod: add I2C hwmods for OMAP2420, 2430"
in linux-next as of 20101203 introduced the following build
warning - fix this by removing the stray i2c_dev_attr.
arch/arm/mach-omap2/omap_hwmod_2430_data.c:483: warning: 'i2c_dev_attr' defined but not used
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
To support tvout on rx51,added Intilization data,
tvout as display device and enabled venc through gpio
on rx51
Signed-off-by: Srikar <ext-srikar.1.bhavanarayana@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Upcoming ASoC core and tlv320aic3x changes makes possible to take b part of
TLV320AIC34 into use on RX51/N900. Prepare to this by adding virtual supplies
and platform data for b part of the codec.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove second tlv320aic3x.h inclusion that came along the commit f0fba2a
"ASoC: multi-component - ASoC Multi-Component Support".
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is no MFD config option, MFD_SUPPORT should be selected instead.
This will prevent build errors when trying out different configurations.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
clk_get() return value should be checked with IS_ERR(). Furthermore,
clocks should be put and disabled properly.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert DMA library into DMA platform driver and make use of
platform data provided by hwmod data base for OMAP2+ onwards.
For OMAP1 processors, the DMA driver in mach-omap uses resource
structures for getting platform data.
Thanks to Tony Lindgren <tony@atomide.com> for fixing various
omap1 issues and testing the same on OSK5912 board.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Prepare OMAP2+ DMA to use hwmod infrastructure so that DMA can register
as platform device.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP4 DMA hwmod data. In addition to original dma hwmod data,
the following changes are added.
1. DMA device attributes structure is introduced for diffenrenciating
OMAP cpu's based on DMA features.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Tested-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2430 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add OMAP2420 DMA hwmod data and also add required
DMA device attributes.
Signed-off-by: G, Manjunath Kondaiah <manjugk@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The convention for omap device naming is omap_XXX.
Rename the device and driver name in order to stick
to this naming convention.
Change device name in clock nodes as well.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Ben Dooks <ben-i2c@fluff.org>
Acked-by: Paul Walmsley <paul@pwsan.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The AXI protocol specifies that the write response can only
be sent back to an AXI master when the last write data has been
accepted. This optimization enables the PL310 to send the write
response of certain write transactions as soon as the store buffer
accepts the write address. This behavior is not compatible with
the AXI protocol and is disabled by default. You enable this
optimization by setting the Early BRESP Enable bit in the
Auxiliary Control Register (bit [30]).
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Mans Rullgard <mans@mansr.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Clearing bit 22 in the PL310 Auxiliary Control register (shared
attribute override enable) has the side effect of transforming Normal
Shared Non-cacheable reads into Cacheable no-allocate reads.
Coherent DMA buffers in Linux always have a Cacheable alias via the
kernel linear mapping and the processor can speculatively load cache
lines into the PL310 controller. With bit 22 cleared, Non-cacheable
reads would unexpectedly hit such cache lines leading to buffer
corruption
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enabling L2 prefetching improves performance as shown on Panda
ES2.1 board with mem test, and it has measurable impact on
performances. I think we should consider it, even though it damages
"writes" a bit. (rebased to k.org)
Usually the prefetch is used at both levels together L1 + L2, however,
to enable the CP15 prefetch engines, these are under security, and on
GP devices, we cannot enable it(e.g. on PandaBoard). However, just
enabling PL310 prefetch seems to provide performance improvement,
as shown in the data below (from Ubuntu) and would be a great thing
to pull in.
What prefetch does is enable automatic next line prefetching. With this
enabled, whenever the PL310 receives a cachable read request, it
automatically prefetches the following cache line as well.
Measurement Data:
==
STOCK 10.10 WITHOUT PATCH
========================
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2aaad000 0x2b2ad000
copy libc 133 MB/s
copy Android v5 273 MB/s
copy Android NEON 235 MB/s
copy INT32 116 MB/s
copy ASM ARM 187 MB/s
copy ASM VLDM 64 204 MB/s
copy ASM VLDM 128 173 MB/s
copy ASM VLD1 216 MB/s
read ASM ARM 286 MB/s
read ASM VLDM 242 MB/s
read ASM VLD1 286 MB/s
write libc 1947 MB/s
write ASM ARM 1943 MB/s
write ASM VSTM 1942 MB/s
write ASM VST1 1935 MB/s
10.10 + PATCH
=============
~# ./memspeed
size 8388608 8192k 8M
offset 8388608, 0
buffers 0x2ab17000 0x2b317000
copy libc 129 MB/s
copy Android v5 256 MB/s
copy Android NEON 356 MB/s
copy INT32 127 MB/s
copy ASM ARM 321 MB/s
copy ASM VLDM 64 337 MB/s
copy ASM VLDM 128 321 MB/s
copy ASM VLD1 350 MB/s
read ASM ARM 496 MB/s
read ASM VLDM 470 MB/s
read ASM VLD1 488 MB/s
write libc 1701 MB/s
write ASM ARM 1682 MB/s
write ASM VSTM 1693 MB/s
write ASM VST1 1681 MB/s
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes the hardcoded value of auxctrl value and
construct it using bitfields
Bit 25 is reserved and is always set to 1. Same value
of this bit is retained in this patch
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
