This patch has removed Momenco Ocelot support from MTD.
Ocelot support has already removed.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Make nandsim use GFP_NOFS when allocating memory, because it might
be used by a file-system (e.g. UBIFS2) which means, if we are short
of memory, we may deadlock. Indee, UBIFS is holding a lock, writes
to the media, reaches this place in NANDsim, kmalloc does not find
the requested amount of RAM, calls memory shrinker, which decides
to writeback inodes, calls FS, and it deadlocks on the lock which
is already being held. Below is the UBIFS backtrace which
demonstrates that:
[<c03717dc>] __mutex_lock_slowpath+0xc8/0x2e6
[<c0371a16>] mutex_lock+0x1c/0x1f
[<f8b9d076>] reserve_space+0x3d/0xa9 [ubifs]
[<f8b9d1bd>] make_one_reservation+0x2b/0x86 [ubifs]
[<f8b9d3fc>] ubifs_jrn_write_block+0xda/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c015d6ab>] shrink_inactive_list+0x7fa/0x969
[<c015d8c8>] shrink_zone+0xae/0x10c
[<c015e3b4>] try_to_free_pages+0x159/0x251
[<c015980a>] __alloc_pages+0x125/0x2f0
[<c016ff6a>] cache_alloc_refill+0x380/0x6ba
[<c01703f3>] __kmalloc+0x14f/0x157
[<f885722a>] do_state_action+0xab7/0xc74 [nandsim]
[<f885760c>] switch_state+0x225/0x402 [nandsim]
[<f8857e7e>] ns_hwcontrol+0x3e2/0x620 [nandsim]
[<f8862f53>] nand_command+0x2e/0x1a5 [nand]
[<f8861ad8>] nand_write_page+0x4a/0x9a [nand]
[<f88617b4>] nand_do_write_ops+0x1cf/0x343 [nand]
[<f8861a70>] nand_write+0x88/0xa6 [nand]
[<f8850b0e>] part_write+0x72/0x8b [mtd]
[<f88e19c5>] ubi_io_write+0x189/0x29c [ubi]
[<f88dfb98>] ubi_eba_write_leb+0xb6/0x699 [ubi]
[<f88def93>] ubi_leb_write+0xe4/0xe9 [ubi]
[<f8ba3b82>] ubifs_wbuf_write_nolock+0x333/0x4c9 [ubifs]
[<f8b9d28c>] write_node+0x74/0x8e [ubifs]
[<f8b9d422>] ubifs_jrn_write_block+0x100/0x12f [ubifs]
[<f8b9ff3a>] ubifs_writepage+0x11d/0x1ec [ubifs]
[<c0159e5b>] __writepage+0xb/0x26
[<c015a318>] write_cache_pages+0x203/0x2d9
[<c015a411>] generic_writepages+0x23/0x2d
[<c015a452>] do_writepages+0x37/0x39
[<c018e24a>] __writeback_single_inode+0x96/0x399
[<c018e903>] sync_sb_inodes+0x1a3/0x274
[<c018ebf3>] writeback_inodes+0xa6/0xd8
[<c015a9dd>] background_writeout+0x86/0x9e
[<c015ae9c>] pdflush+0xfb/0x1b6
[<c01387d7>] kthread+0x37/0x59
[<c0104dc3>] kernel_thread_helper+0x7/0x14
The deadlock is funny because it starts in pdflush/writeback,
and comes back to writeback, then deadlocks. It seems we should look
carefully for other places in UBI and MTD and use GFP_NOFS instead
of GFP_KERNEL.
Caught-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When building NOR flash support, you have compile-time options for the
bus width and the number of individual chips which are interleaved
together onto that bus. The code to deal with arbitrary geometry is a
bit convoluted, and people want to just configure it for the specific
hardware they have, to avoid the runtime overhead.
Selecting _none_ of the available options doesn't make any sense. You
should have at least one. This makes it build though, since people
persist in trying.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
To enable the main read/write at oob ops
Next time we will commit the main read/write support for yaffs2
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Unlike most stuff on the market the chip inside these two allows raw
flash access and doesn't implement and FTL, leaving that functionality
to the device driver.
Raw flash access in a cheap USB cardreader! An MTD test device one can
attach to a PC! What a deal!
The command set of the chip is not documented, so information was
obtained from the existing mass-storage driver
(drivers/usb/storage/alauda.c), its documentation
(http://alauda.sourceforge.net/wikka.php?wakka=BulkCommandReference),
additional reverse engineering and comparison with a vendor driver for a
related chip
(http://www.ratocsystems.com/english/download/driver/linux/sma03u.html).
Signed-off-by: Joern Engel <joern@logfs.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The tqm834x map Kconfig options depends on TQM834x which does not
exist anywhere else in the kernel.
The pq2fads map Kconfig/makefile support was removed a while ago but
the actual file persisted.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
These drivers are specific to 4xx support in arch/ppc at the moment. Make
sure they don't get built on arch/powerpc.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The NUMA layer only supports NUMA policies for the highest zone. When
ZONE_MOVABLE is configured with kernelcore=, the the highest zone becomes
ZONE_MOVABLE. The result is that policies are only applied to allocations
like anonymous pages and page cache allocated from ZONE_MOVABLE when the
zone is used.
This patch applies policies to the two highest zones when the highest zone
is ZONE_MOVABLE. As ZONE_MOVABLE consists of pages from the highest "real"
zone, it's always functionally equivalent.
The patch has been tested on a variety of machines both NUMA and non-NUMA
covering x86, x86_64 and ppc64. No abnormal results were seen in
kernbench, tbench, dbench or hackbench. It passes regression tests from
the numactl package with and without kernelcore= once numactl tests are
patched to wait for vmstat counters to update.
akpm: this is the nasty hack to fix NUMA mempolicies in the presence of
ZONE_MOVABLE and kernelcore= in 2.6.23. Christoph says "For .24 either merge
the mobility or get the other solution that Mel is working on. That solution
would only use a single zonelist per node and filter on the fly. That may
help performance and also help to make memory policies work better."
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Tested-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Cc: Andi Kleen <ak@suse.de>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
au1100fb_fb_blank() should come before au1100fb_setmode().
drivers/video/au1100fb.c: In function 'au1100fb_setmode':
drivers/video/au1100fb.c:211: error: implicit declaration of function 'au1100fb_fb_blank'
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/console/newport_con.c: In function `newport_console_init':
drivers/video/console/newport_con.c:743: warning: return makes integer from pointer without a cast
Although one wonders whether that should have been -ENODEV...
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In file included from drivers/video/console/newport_con.c:16:
include/linux/selection.h:16: warning: "struct tty_struct" declared inside parameter list
include/linux/selection.h:16: warning: its scope is only this definition or declaration, which is probably not what you want
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is the correct fix according to Paul Mackerras and allows an
allyesconfig on PPC64 to build.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xen i386 xen-head.S fix sections mixup
xen-head.S does not come back to the data section, leaving the text section
as current section. It causes problems with a slightly enhanced DEBUG_RODATA
that supports CONFIG_HOTPLUG and bringing a CPU up after the text has been
marked read-only: reference to early_gdt_descr causes a page fault.
Updates:
- It should be using pushsection/popsection.
- Actually, the push/popsections around the ELFNOTEs are redundant; ELFNOTE()
does its own push/popsection to put things into the appropriate .note* section
anyway.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
de_thread:
if (atomic_read(&oldsighand->count) <= 1)
BUG_ON(atomic_read(&sig->count) != 1);
This is not safe without the rmb() in between. The results of two
correctly ordered __exit_signal()->atomic_dec_and_test()'s could be seen
out of order on our CPU.
The same is true for the "thread_group_empty()" case, __unhash_process()'s
changes could be seen before atomic_dec_and_test(&sig->count).
On some platforms (including i386) atomic_read() doesn't provide even the
compiler barrier, in that case these checks are simply racy.
Remove these BUG_ON()'s. Alternatively, we can do something like
BUG_ON( ({ smp_rmb(); atomic_read(&sig->count) != 1; }) );
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Minor tweaks to rtc-max6902: make it hotplug correctly, and fix a few
space-before-tab whitespace botches. This driver has no current in-tree
users, so the hotplug fix changes the driver name.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Print a big fat warning and do what is necessary to continue if a node is
marked as up (meaning either node is online (upstream) or node has memory
(Andrew's tree)) but allocations from the node do not succeed.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SLUB is using atomic_read() for variables declared atomic_long_t.
Switch to atomic_long_read().
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This one-liner patch fixes a bug in drivers/auxdisplay/cfag12864b.c
At cfag12864b_init(), the driver tries to kalloc some memory in the
variable cfag12864b_cache.
Then, as usual, it checks if the call failed. However, it checks
cfag12864b_buffer instead.
This patch changes the "cfag12864b_buffer" to "cfag12864b_cache" so the
correct variable is checked.
Signed-off-by: Miguel Ojeda <maxextreme@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add PCI IDs for the onchip UARTs on PA Semi PWRficient.
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to inconsistent locking in the VFS between calls to lookup and
revalidate deadlock can occur in the automounter.
The inconsistency is that the directory inode mutex is held for both lookup
and revalidate calls when called via lookup_hash whereas it is held only
for lookup during a path walk. Consequently, if the mutex is held during a
call to revalidate autofs4 can't release the mutex to callback the daemon
as it can't know whether it owns the mutex.
This situation happens when a process tries to create a directory within an
automount and a second process also tries to create the same directory
between the lookup and the mkdir. Since the first process has dropped the
mutex for the daemon callback, the second process takes it during
revalidate leading to deadlock between the autofs daemon and the second
process when the daemon tries to create the mount point directory.
After spending quite a bit of time trying to resolve this on more than one
occassion, using rather complex and ulgy approaches, it turns out that just
delaying the hashing of the dentry until the create operation works fine.
Signed-off-by: Ian Kent <raven@themaw.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch which limited the number of sectors in a single request
to a COWed device was correct in concept, but the limit was implemented in
the wrong place.
By putting it in ubd_add, it covered the cases where the COWing was
specified on the command line. However, when the command line only has the
COW file specified, the fact that it's a COW file isn't known until it's
opened, so the limit is missed in these cases.
This patch moves the sector limit from ubd_add to ubd_open_dev.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a raid1 array is reshaped (number of drives changed), the list of devices
is compacted, so that slots for missing devices are filled with working
devices from later slots. This requires the "rd%d" symlinks in sysfs to be
updated.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 1757128438 was slightly bad. If an array
has a write-intent bitmap, and you remove a drive, then readd it, only the
changed parts should be resynced. However after the above commit, this only
works if the array has not been shut down and restarted.
This is because it sets 'fullsync' at little more often than it should. This
patch is more careful.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case bus master driver provided bogus value as its private data, search
can be incorrect. Problem found by Adrian Bunk.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It seems a simple mistake was made when converting follow_hugetlb_page()
over to the VM_FAULT flags bitmasks (in "mm: fault feedback #2", commit
83c54070ee).
By using the wrong bitmask, hugetlb_fault() failures are not being
recognized. This results in an infinite loop whenever follow_hugetlb_page
is involved in a failed fault.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Acked-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Get module reference on open() by generic HDLC to prevent module from
unloading while interface is active.
Signed-off-by: Paul Fulghum <paulkf@microgate.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Skip calling cache_free_alien() when the platform is not numa capable.
This will avoid cache misses that happen while accessing slabp (which is
per page memory reference) to get nodeid. Instead use a global variable to
skip the call, which is mostly likely to be present in the cache.
This gives a 0.8% performance boost with the database oltp workload on a
quad-core SMP platform and by any means the number is not small :)
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this patch any thread can dequeue its own private signals via signalfd,
even if it was created by another sub-thread.
To do so, we pass "current" to dequeue_signal() if the caller is from the same
thread group. This also fixes the scheduling of posix timers broken by the
previous patch.
If the caller doesn't belong to this thread group, we can't handle __SI_TIMER
case properly anyway. Perhaps we should forbid the cross-process signalfd usage
and convert ctx->tsk to ctx->sighand.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
dequeue_signal:
if (__SI_TIMER) {
spin_unlock(&tsk->sighand->siglock);
do_schedule_next_timer(info);
spin_lock(&tsk->sighand->siglock);
}
Unless tsk == curent, this is absolutely unsafe: nothing prevents tsk from
exiting. If signalfd was passed to another process, do_schedule_next_timer()
is just wrong.
Add yet another "tsk == current" check into dequeue_signal().
This patch fixes an oopsable bug, but breaks the scheduling of posix timers
if the shared __SI_TIMER signal was fetched via signalfd attached to another
sub-thread. Mostly fixed by the next patch.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Michael Kerrisk <mtk-manpages@gmx.net>
Cc: Roland McGrath <roland@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sys_timer_create() sets ->it_process and unlocks ->siglock, then checks
tmr->it_sigev_notify to define if get_task_struct() is needed.
We already passed ->it_id to the caller, another thread can delete this timer
and free its memory in between.
As a minimal fix, move this code under ->siglock, sys_timer_delete() takes it
too before calling release_posix_timer(). A proper serialization would be to
take ->it_lock, we add a partly initialized timer on posix_timers_id, not
good.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
timer_delete does:
lock_timer();
timer->it_process = NULL;
unlock_timer();
release_posix_timer();
timer->it_process is checked in lock_timer() to prevent access to a
timer, which is on the way to be deleted, but the check happens after
idr_lock is dropped. This allows release_posix_timer() to delete the
timer before the lock code can check the timer:
CPU 0 CPU 1
lock_timer();
timer->it_process = NULL;
unlock_timer();
lock_timer()
spin_lock(idr_lock);
timer = idr_find();
spin_lock(timer->lock);
spin_unlock(idr_lock);
release_posix_timer();
spin_lock(idr_lock);
idr_remove(timer);
spin_unlock(idr_lock);
free_timer(timer);
if (timer->......)
Change the locking to prevent this.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce CONFIG_CHECK_SIGNATURE to control inclusion of check_signature()
and avoid problems on platforms that don't have readb().
Let the few legacy (ISA || PCI || X86) drivers that need check_signature()
select CONFIG_CHECK_SIGNATURE.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k/mac: Make mac_hid_mouse_emulate_buttons() declaration visible
drivers/char/keyboard.c: In function 'kbd_keycode':
drivers/char/keyboard.c:1142: error: implicit declaration of function 'mac_hid_mouse_emulate_buttons'
The forward declaration of mac_hid_mouse_emulate_buttons() is not visible on
m68k because it's hidden in the middle of a big #ifdef block.
Move it to <linux/kbd_kern.h>, correct the type of the second parameter, and
include <linux/kbd_kern.h> where needed.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
zorro: Make the sysfs `config' attribute read-only, as you cannot write to it
(there's no .write function neither).
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k: Fix a few hickups in drivers/scsi/Kconfig
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't include RODATA into text segment as it includes the kallsyms data and
can cause spurious link failures (layout differences can change the number of
symbols in kallsyms, i.e. when a symbol is equal to _etext it's not
included).
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the needed constants and defines to activate the existing code.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When suspend is ever implemented for pmu68k it really should follow the
generic pm_ops concept and not mirror the platform-specific /dev/pmu
device with ioctls on it. Hence, this patch removes the unused code there;
should the implementers need it they can look at via-pmu.c and/or the
history of the file.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new exec code inserts an accounted vma into an mm struct which is not
current->mm. The existing memory check code has a hard coded assumption
that this does not happen as does the security code.
As the correct mm is known we pass the mm to the security method and the
helper function. A new security test is added for the case where we need
to pass the mm and the existing one is modified to pass current->mm to
avoid the need to change large amounts of code.
(Thanks to Tobias for fixing rejects and testing)
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: WU Fengguang <wfg@mail.ustc.edu.cn>
Cc: James Morris <jmorris@redhat.com>
Cc: Tobias Diedrich <ranma+kernel@tdiedrich.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The new rtc-m41t80 driver name doesn't match its module name, which
prevents it from properly hotplugging. Since it's new, no platforms yet
depend on that name ... so this patch fixes the driver name to match its
module name, rather than going the other way around with a MODULE_ALIAS().
NOTE: This sort of bug is a new thing to watch out for with new-style I2C
drivers; previously I2C couldn't hotplug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lumpy reclaim works by selecting a lead page from the LRU list and then
selecting pages for reclaim from the order-aligned area of pages. In the
situation were all pages in that region are inactive and not referenced by any
process over time, it works well.
In the situation where there is even light load on the system, the pages may
not free quickly. Out of a area of 1024 pages, maybe only 950 of them are
freed when the allocation attempt occurs because lumpy reclaim returned early.
This patch alters the behaviour of direct reclaim for large contiguous
blocks.
The first attempt to call shrink_page_list() is asynchronous but if it fails,
the pages are submitted a second time and the calling process waits for the IO
to complete. This may stall allocators waiting for contiguous memory but that
should be expected behaviour for high-order users. It is preferable behaviour
to potentially queueing unnecessary areas for IO. Note that kswapd will not
stall in this fashion.
[apw@shadowen.org: update to version 2]
[apw@shadowen.org: update to version 3]
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As pointed out by Mel when reclaim is applied at higher orders a significant
amount of IO may be started. As this takes finite time to drain reclaim will
consider more areas than ultimatly needed to satisfy the request. This leads
to more reclaim than strictly required and reduced success rates.
I was able to confirm Mel's test results on systems locally. These show that
even under light load the success rates drop off far more than expected.
Testing with a modified version of his patch (which follows) I was able to
allocate almost all of ZONE_MOVABLE with a near idle system. I ran 5 test
passes sequentially following system boot (the system has 29 hugepages in
ZONE_MOVABLE):
2.6.23-rc1 11 8 6 7 7
sync_lumpy 28 28 29 29 26
These show that although hugely better than the near 0% success normally
expected we can only allocate about a 1/4 of the zone. Using synchronous
reclaim for these allocations we get close to 100% as expected.
I have also run our standard high order tests and these show no regressions in
allocation success rates at rest, and some significant improvements under
load.
This patch:
We are transitioning pages from active to inactive in clear_active_flags,
those need counting as PGDEACTIVATE vm events.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
