At least one report claims that a878539ef9
failed to solve lockups, whereas the old limit-to-32-bit trick worked.
Restore the 32-bit limit, but also leave the 255-sector limit in place,
because we know that's needed as well.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
A Promise SATA controller will signal hotplug events when a hard
reset (COMRESET) is done on a port. These events aren't masked by
the driver, and the unexpected interrupts will cause a sequence
of failed reset attempts util libata's EH finally gives up.
This has not been a common problem so far, but the pending libata
hardreset-by-default changes makes it a critical issue.
The solution is to disable hotplug events before a reset, and to
reenable them afterwards. (Promise's driver does this too.)
This patch adds SATA-specific versions of ->freeze() and ->thaw()
that also disable and enable hotplug events. PATA ports continue
to use the old versions of ->freeze() and ->thaw().
Accesses to the hotplug register must be serialised via host->lock.
We rely on ap->lock == &ap->host->lock and that libata takes this
lock before ->freeze() and ->thaw(). Document this requirement.
The interrupt handler is adjusted so its hotplug register accesses
are inside the region protected by host->lock.
Tested on various chips (SATA300TX4, SATA300TX2plus, SATAII150TX4,
FastTrack TX4000) with various combinations of SATA and PATA disks,
with and without the pending hardreset-by-default changes.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no point in retrying and eventually failing device detection
when the device rejects READ_NATIVE_MAX[_EXT]. Disable HPA unlocking
if READ_NATIVE_MAX[_EXT] is rejected as done when SET_MAX[_EXT] is
rejected.
This allows some old drives to work even if they aren't blacklisted.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This is to fix bugzilla #10254. QSI cdrom attached to pata_sis as
secondary master appears as phantom device for the slave.
Interestingly, instead of not setting DRQ after IDENTIFY which
triggers NODEV_HINT, it aborts both IDENTIFY and IDENTIFY PACKET which
makes EH retry.
Modify EH such that it assumes no device is attached if both flavors
of IDENTIFY are aborted by the device. There really isn't much point
in retrying when the device actively aborts the commands.
While at it, convert NODEV detection message to ata_dev_printk() to
help debugging obscure detection problems.
This problem was reported by Jan Bücken.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Jan Bücken <jb.faq@gmx.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_it821x needs to look at raw request size in check_atapi_dma().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement ata_qc_raw_nbytes() which determines the raw user-requested
size of a PC command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Fix Oops with TQM5200 on TQM5200
[POWERPC] mpc5200: Fix null dereference if bestcomm fails to initialize
[POWERPC] mpc5200-fec: Fix possible NULL dereference in mdio driver
[POWERPC] Fix crash in init_ipic_sysfs on efika
[POWERPC] Don't use 64k pages for ioremap on pSeries
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: exec PT_DTRACE
[SPARC64]: Use shorter list_splice_init() for brevity.
[SPARC64]: Remove most limitations to kernel image size.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
sch_htb: fix "too many events" situation
connector: convert to single-threaded workqueue
[ATM]: When proc_create() fails, do some error handling work and return -ENOMEM.
[SUNGEM]: Fix NAPI assertion failure.
BNX2X: prevent ethtool from setting port type
[9P] net/9p/trans_fd.c: remove unused variable
[IPV6] net/ipv6/ndisc.c: remove unused variable
[IPV4] fib_trie: fix warning from rcu_assign_poinger
[TCP]: Let skbs grow over a page on fast peers
[DLCI]: Fix tiny race between module unload and sock_ioctl.
[SCTP]: Fix build warnings with IPV6 disabled.
[IPV4]: Fix null dereference in ip_defrag
The iWARP protocol limits RDMA read requests to a single scatter
entry. NFS/RDMA has code in rdma_read_max_sge() that is supposed to
limit the sge_count for RDMA read requests to 1, but the code to do
that is inside an #ifdef RDMA_TRANSPORT_IWARP block. In the mainline
kernel at least, RDMA_TRANSPORT_IWARP is an enum and not a
preprocessor #define, so the #ifdef'ed code is never compiled.
In my test of a kernel build with -j8 on an NFS/RDMA mount, this
problem eventually leads to trouble starting with:
svcrdma: Error posting send = -22
svcrdma : RDMA_READ error = -22
and things go downhill from there.
The trivial fix is to delete the #ifdef guard. The check seems to be
a remnant of when the NFS/RDMA code was not merged and needed to
compile against multiple kernel versions, although I don't think it
ever worked as intended. In any case now that the code is upstream
there's no need to test whether the RDMA_TRANSPORT_IWARP constant is
defined or not.
Without this patch, my kernel build on an NFS/RDMA mount using NetEffect
adapters quickly and 100% reproducibly failed with an error like:
ld: final link failed: Software caused connection abort
With the patch applied I was able to complete a kernel build on the
same setup.
(Tom Tucker says this is "actually an _ancient_ remnant when it had to
compile against iWARP vs. non-iWARP enabled OFA trees.")
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Acked-by: Tom Tucker <tom@opengridcomputing.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It appears that 64-bit PCI resources cannot possibly ever have worked on
x86-32 even when the RESOURCES_64BIT config option was set, because any
driver that tried to [pci_]ioremap() the resource would have been unable
to do so because the high 32 bits would have been silently dropped on
the floor by the ioremap() routines that only used "unsigned long".
Change them to use "resource_size_t" instead, which properly encodes the
whole 64-bit resource data if RESOURCES_64BIT is enabled.
Acked-by: H. Peter Anvin <hpa@kernel.org>
Acked-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The printk() can deadlock because it can wake up klogd(), and
task enqueueing will try to read the time in order to set a hrtimer.
Reported-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Debugged-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The "bestcomm-core" driver defines its of_match table as follows
static struct of_device_id mpc52xx_bcom_of_match[] = {
{ .type = "dma-controller", .compatible = "fsl,mpc5200-bestcomm", },
{ .type = "dma-controller", .compatible = "mpc5200-bestcomm", },
{},
};
so while registering the driver, the driver's probe function won't be
called, because the device tree node doesn't have a device_type
property. Thus the driver's bcom_engine structure won't be allocated.
Referencing this structure later causes observed Oops.
Checking bcom_eng pointer for NULL before referencing data pointed
by it prevents oopsing, but fec driver still doesn't work (because
of the lost bestcomm match and resulted task allocation failure).
Actually the compatible property exists and should match and so
the fec driver should work.
This removes .type = "dma-controller" from the bestcomm driver's
mpc52xx_bcom_of_match table to solve the problem.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the bestcomm initialization fails, calls to the task allocate
function should fail gracefully instead of oopsing with a NULL deref.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the reg property is missing from the phy node (unlikely, but possible),
then the kernel will oops with a NULL pointer dereference. This fixes
it by checking the pointer first.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The global primary_ipic in arch/powerpc/sysdev/ipic.c can remain NULL
if ipic_init() fails, which will happen on machines that don't have an
ipic interrupt controller. init_ipic_sysfs() will crash in that case.
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
On pSeries, the hypervisor doesn't let us map in the eHEA ethernet
adapter using 64k pages, and thus the ehea driver will fail if 64k
pages are configured. This works around the problem by always
using 4k pages for ioremap on pSeries (but not on other platforms).
A better fix would be to check whether the partition could ever
have an eHEA adapter, and only force 4k pages if it could, but this
will do for 2.6.25.
This is based on an earlier patch by Tony Breeds.
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PT_DTRACE flag is meaningless and obsolete.
Don't touch it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HTB is event driven algorithm and part of its work is to apply
scheduled events at proper times. It tried to defend itself from
livelock by processing only limited number of events per dequeue.
Because of faster computers some users already hit this hardcoded
limit.
This patch limits processing up to 2 jiffies (why not 1 jiffie ?
because it might stop prematurely when only fraction of jiffie
remains).
Signed-off-by: Martin Devera <devik@cdi.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
We don't need one cqueue thread for each CPU. cqueue is used for
receiving userspace datagrams, which are very rare and thus will
happily live with a single queue.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Johannes Berg:
I started getting this warning with recent kernels:
[ 773.908927] ------------[ cut here ]------------
[ 773.908954] Badness at net/core/dev.c:2204
...
If we loop more than once in gem_poll(), we'll
use more than the real budget in our gem_rx()
calls, thus eventually trigger the caller's
assertions in net_rx_action().
Subtract "work_done" from "budget" for the second
arg to gem_rx() to fix the bug.
Signed-off-by: David S. Miller <davem@davemloft.net>
On 10GBaseT boards setting the type to TP will cause the driver to try
to configure 1GBaseT.
Since there are currently no boards that support setting of the port
type, disable this for now.
Signed-off-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable cb is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The variable hlen is initialized but never used otherwise.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
type T;
identifier i;
constant C;
@@
(
extern T i;
|
- T i;
<+... when != i
- i = C;
...+>
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This gets rid of a warning caused by the test in rcu_assign_pointer.
I tried to fix rcu_assign_pointer, but that devolved into a long set
of discussions about doing it right that came to no real solution.
Since the test in rcu_assign_pointer for constant NULL would never
succeed in fib_trie, just open code instead.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
Revert "ide-tape: schedule driver for removal after 6 months"
ide: mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted
ide: mark "hdx=[driver_name]" and "hdx=scsi" kernel parameters as obsoleted
ide: Documentation/ide/ide.txt fixes
ide: mark special "ide0=" kernel parameters as obsoleted
ide: remove commented out entries from ide_pio_blacklist[]
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
[CIFS] Fix mem leak on dfs referral
[CIFS] file create with acl support enabled is slow
[CIFS] Fix mtime on cp -p when file data cached but written out too late
[CIFS] Fix build problem
[CIFS] cifs: replace remaining __FUNCTION__ occurrences
[CIFS] DFS patch that connects inode with dfs handling ops
Change pagemap output format to allow for future reporting of huge pages.
(Format comment and minor cleanups: mpm@selenic.com)
Signed-off-by: Hans Rosenfeld <hans.rosenfeld@amd.com>
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Suppressing uevents turned out to be a bad idea as it screws up the
order of events, making user space very confused. Change the system to
use sysfs groups instead.
This is a regression that, for some odd reason, has gone unnoticed for
some time. It confuses hal so that the block devices (which have the
mmc device as a parent) are not registered. End result being that
desktop magic when cards are inserted won't work.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Increase the number of PnP memory resources from 12 to 24.
This removes an "exceeded the max num of mem resources" warning on boot. I
also noticed the reservation of two more iomem ranges on the computer on
which this was tested.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
PNP_MAX_MEM and PNP_MAX_PORT are mainly used to size tables of PNP
device resources. In 2.6.24, we increased their values to accomodate
ACPI devices that have many resources:
2.6.23 2.6.24
------ ------
PNP_MAX_MEM 4 12
PNP_MAX_PORT 8 40
However, ISAPNP also used these constants as the size of parts of the
logical device register set. This register set is fixed by hardware,
so increasing the constants meant that we were reading and writing
unintended parts of the register set.
This patch changes ISAPNP to use the correct register set sizes (the
same values we used prior to 2.6.24).
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
While testing the virtio-net driver on KVM with TSO I noticed
that TSO performance with a 1500 MTU is significantly worse
compared to the performance of non-TSO with a 16436 MTU. The
packet dump shows that most of the packets sent are smaller
than a page.
Looking at the code this actually is quite obvious as it always
stop extending the packet if it's the first packet yet to be
sent and if it's larger than the MSS. Since each extension is
bound by the page size, this means that (given a 1500 MTU) we're
very unlikely to construct packets greater than a page, provided
that the receiver and the path is fast enough so that packets can
always be sent immediately.
The fix is also quite obvious. The push calls inside the loop
is just an optimisation so that we don't end up doing all the
sending at the end of the loop. Therefore there is no specific
reason why it has to do so at MSS boundaries. For TSO, the
most natural extension of this optimisation is to do the pushing
once the skb exceeds the TSO size goal.
This is what the patch does and testing with KVM shows that the
TSO performance with a 1500 MTU easily surpasses that of a 16436
MTU and indeed the packet sizes sent are generally larger than
16436.
I don't see any obvious downsides for slower peers or connections,
but it would be prudent to test this extensively to ensure that
those cases don't regress.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert
commit f62f1fc9ef
Author: Yinghai Lu <yhlu.kernel@gmail.com>
Date: Fri Mar 7 15:02:50 2008 -0800
x86: reserve dma32 early for gart
The patch has a dependency on bootmem modifications which are not .25
material that late in the -rc cycle. The problem which is addressed by
the patch is limited to machines with 256G and more memory booted with
NUMA disabled. This is not a .25 regression and the audience which is
affected by this problem is very limited, so it's safer to do the
revert than pulling in intrusive bootmem changes right now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit d48567dd43.
Borislav is working on ide-tape "light" version instead.
Cc: Borislav Petkov <petkovbb@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark "hdx=remap" and "hdx=remap63" kernel parameters as obsoleted
(they are layering violation and should be dealt with in the same
way as done by libata - device-mapper should be used instead).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark "hdx=[driver_name]" and "hdx=scsi" kernel parameters as obsoleted
(nowadays device-driver binding can be changed at runtime through sysfs
and it can also be dealt with using per device driver parameters).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* "hdx=cyls,heads,sects,wpcom,irq" should be "hdx=cyls,heads,sects".
* "hdx=" is for "x" from 'a' to 'u', "idex=" is for "x" from '0' to '9'.
* "idex=noautotune" is long gone.
* Obsoleted "ide0=" parameters were already removed from the documentation.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Mark "ide0=ali14xx|cmd640_vlb|dtc2278|ht6560b|qd65xx|umc8672" kernel
parameters as obsoleted (per host driver replacements have been available
for a long time).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently kernel images are limited to 8MB in size, and this causes
problems especially when enabling features that take up a lot of
kernel image space such as lockdep.
The code now will align the kernel image size up to 4MB and map that
many locked TLB entries. So, the only practical limitation is the
number of available locked TLB entries which is 16 on Cheetah and 64
on pre-Cheetah sparc64 cpus. Niagara cpus don't actually have hw
locked TLB entry support. Rather, the hypervisor transparently
provides support for "locked" TLB entries since it runs with physical
addressing and does the initial TLB miss processing.
Fully utilizing this change requires some help from SILO, a patch for
which will be submitted to the maintainer. Essentially, SILO will
only currently map up to 8MB for the kernel image and that needs to be
increased.
Note that neither this patch nor the SILO bits will help with network
booting. The openfirmware code will only map up to a certain amount
of kernel image during a network boot and there isn't much we can to
about that other than to implemented a layered network booting
facility. Solaris has this, and calls it "wanboot" and we may
implement something similar at some point.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a narrow pedantry :) but the dlci_ioctl_hook check and call
should not be parted with the mutex lock.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduced by 270637abff
("[SCTP]: Fix a race between module load and protosw access")
Reported by Gabriel C:
In file included from net/sctp/sm_statetable.c:50:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
In file included from net/sctp/sm_statefuns.c:62:
include/net/sctp/sctp.h: In function 'sctp_v6_pf_init':
include/net/sctp/sctp.h:392: warning: 'return' with a value, in function returning void
...
Signed-off-by: David S. Miller <davem@davemloft.net>
Been seeing occasional panics in my testing of 2.6.25-rc in ip_defrag.
Offending line in ip_defrag is here:
net = skb->dev->nd_net
where dev is NULL. Bisected the problem down to commit
ac18e7509e ([NETNS][FRAGS]: Make the
inet_frag_queue lookup work in namespaces).
Below patch (idea from Patrick McHardy) fixes the problem for me.
Signed-off-by: Phil Oester <kernel@linuxace.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the calculation of the MSS for RDMA connections: we need to
allow space in frames for a VLAN tag too.
Signed-off-by: Chien Tung <ctung@neteffect.com>
Signed-off-by: Glenn Streiff <gstreiff@neteffect.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
