The PCMCIA layer obsoleted asking for per device private IRQS some years
ago and all the drivers by inspection correctly use dev_id and handle
shared interrupts [they get em anyway in most PCI bridged PCMCIA/Cardbus]
so can be adjusted.
This gets rid of the various bugs reported where there is spewage about
conflicting irq types and sometimes the driver won't load.
(Note I don't have all of these devices to test each one beyond by inspection)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are two improvements in this simple patch:
1. wiphy_counter is a static var only used in one function, so
can use local static instead of global static;
2. wiphy_counter wrap handling killed one comparision;
Signed-off-by: Denis ChengRq <crquan@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a crypto key is being removed, rt2x00mac should not
reset the key->hw_key_idx value because that will prevent
the driver from removing the correct key from the hardware.
Furthermore ffz() starts counting at 0 instead of 1, so we don't
need to substract 1 from the resulting value.
Signed-off-by: Stephen Blackheath <tramp.enshrine.stephen@blacksapphire.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the led behavior in IBSS. After we joined an IBSS cell we
need to inform the led that we got associated. Although there is no 802.11
association in IBSS mode, the semantic of "There is a link" is relevant.
This allows the led to blink in IBSS mode (at least this solves a bug for
iwlwifi).
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While associated, we should probe with the SSID we're associated to,
not the scan SSID.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Long awaited, hard work. This patch totally cleans up the rate control
API to remove the requirement to include internal headers outside of
net/mac80211/.
There's one internal use in the PID algorithm left for mesh networking,
we'll have to figure out a way to clean that one up and decide how to
do the peer link evaluation, possibly independent of the rate control
algorithm or via new API.
Additionally, ath9k is left using the cross-inclusion hack for now, we
will add new API where necessary to make this work properly, but right
now I'm not expert enough to do it. It's still off better than before.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When I split off the action frame handling I made the code drop
all action frames we don't want to handle. This is wrong since
some action frames are actually handled via rx_h_mgmt through
being queued to the sta/mesh implementations.
Thanks to Li YanBo for noticing the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: Li YanBo <dreamfly281@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the mesh code doesn't support bridging mesh point interfaces
with wired ethernet or AP to construct an MPP or MAP. This patch adds
code to support the "6 address frame format packet" functionality to
mesh point interfaces. Now the mesh network can be used as backhaul
for end to end communication.
Signed-off-by: Li YanBo <dreamfly281@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF adjust is needed only for AP mode when staggered beacons
are used. Since we support only a single interface in IBSS mode,
disable setting the TSF adjust register.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
nexttbtt has to be obtained from the timestamp of the beacon
obtained from mac80211. Fix this.
And <asm/unaligned.h> is not needed anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, remove comments that are not relevant anymore.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes the HT flags from RXON when moving from HT to legacy.
This avoids keeping those flags set and possibly miss configuring firmware.
If we are configured in HT, fat channel: channel 1 above, and move later
to legacy channel 11, we need to clear the FAT channel control flags in
RXON. If we don't, the firmware will understand this as channel 11 above
which is not possible due to regulatory constraints, leading to firmware
crash.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses comments from Dan Williams about the patch
committed as "libertas: Reduce the WPA key installation time."
Signed-off-by: Javier Cardona <javier@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Fix bad udelay calls (using > 2000us) in AR5210 code and clean up
some bits on nic_reset (AR5210 support is still in bad shape)
Changes-licensed-under: ISC
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reject configuring mesh-id for non-mesh, monitor flags for non-monitor.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We currently allow monitor flags changes and mesh ID changes when
the interface is up, which can lead to trouble. Change it to only
allow when down.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes cfg80211 show the interface in the nl80211
information about a specific interface. API users are required
to keep the type updated (everything else is fairly complicated)
but you will get a warning if you fail to keep it updated.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no need to register the master netdev with cfg80211,
in fact, this is quite dangerous and lead to having to add
checks for the master interface all over the config handlers.
This patch removes the "ieee80211_ptr" from the master iface
in favour of having a small netdev_priv() associated with
the master interface that stores the ieee80211_local pointer.
Because of this, a lot of code in the configuration handlers
can go away. To make this patch easier to verify I have also
removed a number of wiphy_priv() calls in favour of getting
the sdata first and then the local pointer from that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds named constants for configuring MIMO power save
chain settings.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Scan need to be delayed only after association to allow EAPOL
exchange. We don't need the delay for IBSS mode.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the system is misconfigured with CONFIG_RFKILL set but CONFIG_RFKILL_INPUT
not set, the built-in radio LEDs will not work. In the current code, no warning
is issued.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis added the regulatory hint stuff to this file without
observing that __ieee80211_get_channel and ieee80211_get_channel
really belong together.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The statically defined regdomains are used in a very convoluted
way, use them instead to prime the information we have and then
continue operating normally.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few pointers and structures in the regulatory code are const,
but because it wasn't done properly a whole bunch of bogus
casts were needed to compile without warning. Mark everything
const properly to avoid that kind of junk code.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent code from Luis is an #ifdef hell and contains lots of
code that's stuffed into the wrong file making a whole bunch of
things needlessly non-static, and besides, what is it doing in
core.c??
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When Luis added the static regdomains back he used +/-20
of the centre frequencies to account for 40MHz bandwidth
neglecting the fact that 40MHz bandwidth cannot be used
on the channels close to the allowed band edges.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The SIOCSIWSCAN handler is passed data in an iw_point structure. Some
drivers erronously use an iw_param instead.
On 32 bit architectures the difference isn't noticed as the flags
parameter tends to be the only one used by scan handlers and is at the
same offset.
On 64 bit architectures the pointer in the iw_point structure means the
flag parameter is at different offsets in these structures.
Thanks to Jean Tourrilhes for tracking this down for orinoco, and Pavel
Roskin for confirming the fix and identifying other suspect handlers.
Signed-off-by: David Kilroy <kilroyd@googlemail.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported by Thomas Graf.
If we don't unlink the SKB from the queue when we send it
out in aoenet_xmit(), dev_hard_start_xmit() will see skb->next
as non-NULL and interpret this to mean the SKB is part of a
GSO segment list.
Add __skb_unlink() call to fix that.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a usage documentation for the virtual CAN driver (vcan).
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current check wrongly uses the state of one (currently the first)
tx queue for all tx queues in case of non-default qdiscs. This check
mainly prevented requeuing loop with __netif_schedule(), but now it's
controlled inside __qdisc_run(), while dequeuing. The wrongness of
this check was first noticed by Herbert Xu.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A lot of code wants to iterate over an SKB queue at the top level using
it's own control structure and iterator scheme.
Provide skb_queue_next(), which is only valid to invoke if
skb_queue_is_last() returns false.
Signed-off-by: David S. Miller <davem@davemloft.net>
Several bits of code want to know "is this the last SKB in
a queue", and all of them implement this by hand.
Provide an common interface to make this check.
Signed-off-by: David S. Miller <davem@davemloft.net>
Check in dequeue_skb() the state of tx_queue for requeued skb to save
on locking and re-requeuing, and possibly remove the current check in
qdisc_run(). Based on the idea of Alexander Duyck.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason to call into the complicated qdiscs
just to remember the last SKB where we found the device
blocked.
The SKB is outside of the qdiscs realm at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
Handle the case of head being non-empty, by adding list->qlen
to head->qlen instead of using direct assignment.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch add support for keeping an additional character alias
associated with an network interface. This is useful for maintaining
the SNMP ifAlias value which is a user defined value. Routers use this
to hold information like which circuit or line it is connected to. It
is just an arbitrary text label on the network device.
There are two exposed interfaces with this patch, the value can be
read/written either via netlink or sysfs.
This could be maintained just by the snmp daemon, but it is more
generally useful for other management tools, and the kernel is good
place to act as an agreed upon interface to store it.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
