Add code to save/restore registers during
R-standby sleep on SH-Mobile processors.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the SH clocksource drivers follow the scheme that the IRQ is setup
prior to registering the clockevent. The interrupt handler in the
clockevent cases looks to the event handler function pointer being filled
in by the registration code, permitting us to get in to situations where
asserted IRQs step in to the handler before registration has had a chance
to complete and hitting a NULL pointer deref.
In practice this is not an issue for most platforms, but some of them
with fairly special loaders (or that are chain-loading from another
kernel) may enter in to this situation. This fixes up the oops reported
by Rafael on hp6xx.
Reported-and-tested-by: Rafael Ignacio Zurita <rafaelignacio.zurita@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
KEYSC::SCN register of SH7724 is 3bit.
Thus, scan_timing should be 0 - 7 here.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This hooks up the SET/GET_UNALIGN_CTL knobs cribbing the bulk of it from
the PPC and ia64 implementations. The thread flags happen to be the
logical inverse of what the global fault mode is set to, so this works
out pretty cleanly. By default the global fault mode is used, with tasks
now being able to override their own settings via prctl().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When FSI and Network (= NFS file system) were used at the same time,
the I/O of FSI was unstable. This patch updates the SPU2 clock (which
is used for FSI) to solve this issue. Special thanks to Jeremy.
Signed-off-by: Jeremy Baker <Jeremy.Baker@renesas.com>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7724 processor code to always enable vpu_clk.
On the Ecovec board, set the vpu_clk to 166 Mhz.
The 166MHz setting results in a divide-by-6 setup for
vpu_clk and improves the VPU performance compared to the
power-on-reset/bootloader configuration.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds a ->kick() callback to clk_div4_table
and ties it into sh_clk_div4_set_rate(). A sh7724
specific kick function is also added that updates the
KICK bit whenever div4 clocks in FRQCRA and FRQCRB
have been set. Allows us to set the VPU clock.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch introduces struct clk_div4_table. The structure
will be used to keep div4 specific data, and is with this
patch replacing the struct clk_div_mult_table pointer arg
used by the sh_clk_div4_register() functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure the div4 bitfield is shifted according
to the enable_bit value in sh_clk_div4_set_rate().
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements a bit of rework for the PMB code, which permits us to
kill off the legacy PMB mode completely. Rather than trusting the boot
loader to do the right thing, we do a quick verification of the PMB
contents to determine whether to have the kernel setup the initial
mappings or whether it needs to mangle them later on instead.
If we're booting from legacy mappings, the kernel will now take control
of them and make them match the kernel's initial mapping configuration.
This is accomplished by breaking the initialization phase out in to
multiple steps: synchronization, merging, and resizing. With the recent
rework, the synchronization code establishes page links for compound
mappings already, so we build on top of this for promoting mappings and
reclaiming unused slots.
At the same time, the changes introduced for the uncached helpers also
permit us to dynamically resize the uncached mapping without any
particular headaches. The smallest page size is more than sufficient for
mapping all of kernel text, and as we're careful not to jump to any far
off locations in the setup code the mapping can safely be resized
regardless of whether we are executing from it or not.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The PMB code is an example of something that spends an absurd amount of
time running uncached when only a couple of operations really need to be.
This switches over to the shiny new uncached helpers, permitting us to
spend far more time running cached.
Additionally, MMUCR twiddling is perfectly safe from cached space given
that it's paired with a control register barrier, so fix that up, too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are lots of registers that can only be updated from the uncached
mapping, so we add some helpers for those cases in order to make it
easier to ensure that we only make the jump when it's absolutely
necessary.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements some locking for the PMB code. A high level rwlock is
added for dealing with rw accesses on the entry map while a per-entry
data structure spinlock is added to deal with the PMB entry changing out
from underneath us.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Write-through PMB mappings still require the cache bit to be set, even if
they're to be flagged with a different cache policy and bufferability
bit. To reduce some of the confusion surrounding the flag encoding we
centralize the cache mask based on the system cache policy while we're at
it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in entry sizing support for existing mappings and then builds
on top of that for linking together entries that are mapping contiguous
areas. This will ultimately permit us to coalesce mappings and promote
head pages while reclaiming PMB slots for dynamic remapping.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some helper routines for uncached mapping support. This
simplifies some of the cases where we need to check the uncached mapping
boundaries in addition to giving us a centralized location for building
more complex manipulation on top of.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some overdue cleanup of the PMB code, killing off unused functionality
and duplication sprinkled about the tree.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Both the store queue API and the PMB remapping take unsigned long for
their pgprot flags, which cuts off the extended protection bits. In the
case of the PMB this isn't really a problem since the cache attribute
bits that we care about are all in the lower 32-bits, but we do it just
to be safe. The store queue remapping on the other hand depends on the
extended prot bits for enabling userspace access to the mappings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7723 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7722 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently there's an ordering issue with the chained handler change
which places the set_irq_chip() after set_irq_chained_handler(). This
causes a warning to be emitted as the IRQ chip needs to be set first.
However, there is the caveat that redirect IRQs can't use the parent
IRQ's irq chip as they are just dummy redirects, resulting in
intc_enable() blowing up when set_irq_chained_handler() attempts to
start up the redirect IRQ. In these cases we can just use dummy_irq_chip
directly, as we already extract the parent IRQ and chip from the redirect
handler.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
vmemmap and the vmsplit code amongst others need to be able to take page
faults much earlier than trap_init() time, so move this in to the early
CPU initialization. VBR setup for secondary CPUs is already handled
through start_secondary(), so we only need to do this for the boot CPU.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The __va()/__pa() offsets and the boot memory offsets are consistent for
all PMB users, so there is no need to special case these for legacy PMB.
Kill the special casing off and depend on CONFIG_PMB across the board.
This also fixes up yet another addressing bug for sh64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This merges the code for iterating over the legacy PMB mappings and the
code for synchronizing software state with the hardware mappings. There's
really no reason to do the same iteration twice, and this also buys us
the legacy entry logging facility for the dynamic PMB case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The PMB initialization code walks the entries and synchronizes the
software PMB state with the hardware mappings, preserving the slot index.
Unfortunately pmb_alloc() only tested the bit position in the entry map
and failed to set it, resulting in subsequent remaps being able to be
dynamically assigned a slot that trampled an existing boot mapping with
general badness ensuing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update the sh7724 INTC tables with force_enable support
to mask out pending unsupported SDHI interrupt sources.
Without this patch the kernel locks up due to a pending
SDHI interrupt that the tmio_mmc driver cannot handle.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Extend the shared INTC code with force_disable support to
allow keeping mask bits statically disabled. Needed for
SDHI support to mask out unsupported interrupt sources.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixed SH-Mobile panning. Previously the address of the frame to be displayed
was updated in the VSync end interrupt. This meant there was a minimum of 1
frame bewteen calling FBIOPAN_DISPLAY ioctl and the pan occuring. This meant
that apps were not able to use the FBIO_WAITFORVSYNC ioctl to wait for the
pan to complete. This patch moves the write to LDSA1R mirror reg into the
pan ioctl. Tested on MS7724 board against 2.6.33-rc7
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Added FBIO_WAITFORVSYNC ioctl for SH-Mobile devices.
Tested on MS7724 and MigoR boards against 2.6.33-rc7.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the parisc change to ensure that tracehook_signal_handler()
is aware of when we are single-stepping in order to ptrace_notify()
appropriately. While this was implemented for 32-bit SH, sh64 neglected
to make use of TIF_SINGLESTEP when it was folded in with the 32-bit code,
resulting in ptrace_notify() never being called.
As sh64 uses all of the other abstractions already, this simply plugs in
the thread flag in the appropriate enable/disable paths and fixes up the
tracehook notification accordingly. With this in place, sh64 is brought
in line with what 32-bit is already doing.
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: hold ref on flip object until it completes
drm/i915: Fix crash while aborting hibernation
drm/i915: Correctly return -ENOMEM on allocation failure in cmdbuf ioctls.
drm/i915: fix pipe source image setting in flip command
drm/i915: fix flip done interrupt on Ironlake
drm/i915: untangle page flip completion
drm/i915: handle FBC and self-refresh better
drm/i915: Increase fb alignment to 64k
drm/i915: Update write_domains on active list after flush.
drm/i915: Rework DPLL calculation parameters for Ironlake
Replace the zero-division warning message with WARN_ON_ONCE() per the
advice by Linus. This shouldn't happen, but if it happens, it's
possible that the bug happens often due to buggy IRQs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Mike Frysinger pointed out that calling tracehook_signal_handler with
stepping=0 missed testing the thread flags, resulting in not calling
ptrace_notify. Fix this by testing if we're single stepping or branch
stepping and setting the flag accordingly.
Tested, seems to work.
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
regulator/lp3971: vol_map out of bounds in lp3971_{ldo,dcdc}_set_voltage()
regulator: Fix display of null constraints for regulators
After `for (val = LDO_VOL_MIN_IDX; val <= LDO_VOL_MAX_IDX; val++)', if no break
occurs, val reaches LDO_VOL_MIN_IDX + 1, which is out of bounds for
ldo45_voltage_map[] and ldo123_voltage_map[].
Similarly BUCK_TARGET_VOL_MAX_IDX + 1 is out of bounds for buck_voltage_map[].
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If the regulator constraints are empty and there is no voltage
reported then nothing will be added to the text displayed for the
constraints, leading to random stack data being printed. This is
unlikely to happen for practical regulators since most will at
least report a voltage but should still be fixed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This patch solves a corner case during allocation which occurs if both
metadata (indirect) and data blocks are required but there is an
obstacle in the filesystem (e.g. a resource group header or another
allocated block) such that when the allocation is requested only
enough blocks for the metadata are returned.
By changing the exit condition of this loop, we ensure that a
minimum of one data block will always be returned.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
We need this one-liner to signal the mount helper of the 'insufficient journals' condition.
Signed-off-by: Abhijith Das <adas@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
