The same patch to add support for MTK gps loggers was submitted by two
different people and applied twice. Remove the redundant lines.
Signed-off-by: James Treacy <treacy@debian.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While disabling an endpoint the driver nuking any pending requests,
thus completing them with -ESHUTDOWN status. But the driver doesn't
clear the tx_req, which means that a next TX request (after
ep_enable), might get stalled, since the driver won't queue the new
reqests.
This patch fixes a bug I'm observing with ethernet gadget while
playing with ifconfig usb0 up/down (the up/down sequence disables
and enables `in' and `out' endpoints).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Before freeing an endpoint's muram memory, we should stop all activity
of the endpoint, otherwise the QE UDC controller might do nasty things
with the muram memory that isn't belong to that endpoint anymore.
The qe_ep_reset() effectively flushes the hardware fifos, finishes all
late transaction and thus prevents the corruption.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Freescale QE UDC controllers can't report the "port change" states,
so the only way to handle disconnects is to process bus reset
interrupts. The bus reset can take some time, that is, few irqs.
Gadgets may print the disconnection events, and this causes few
repetitive messages in the kernel log.
This patch fixes the issue by using the usb_state machine, if the
usb controller has been already reset, just quit the reset irq
early.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
qe_udc_reg_init() leaves the USB controller enabled before muram memory
initialized. Sometimes the uninitialized muram memory confuses the
controller, and it start sending the busy interrupts.
Fix this by disabling the controller, it will be enabled later by
the gadget driver, at bind time.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The call chain is this:
qe_udc_irq() <- grabs the udc->lock spinlock
rx_irq()
qe_ep0_rx()
ep0_setup_handle()
setup_received_handle()
ch9getstatus()
qe_ep_queue() <- tries to grab the udc->lock again
It seems unsafe to temporarily drop the lock in the ch9getstatus(),
so to fix that bug the lock-less __qe_ep_queue() function
implemented and used by the ch9getstatus().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In case of probing errors the driver kfrees the udc_controller, but it
doesn't set the pointer to NULL.
When usb_gadget_register_driver is called, it checks for udc_controller
!= NULL, the check passes and the driver accesses nonexistent memory.
Fix this by setting udc_controller to NULL in case of errors.
While at it, also implement irq_of_parse_and_map()'s failure and cleanup
cases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The DRI people seem to have a hard time getting these right (see also
commit aeb565dfc3).
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/i915: select framebuffer support automatically
drm/i915: add get_vblank_counter function for GM45
drm/i915: capture last_vblank count at IRQ uninstall time too
drm/i915: Unlock mutex on i915_gem_fault() error path
drm/i915: Quiet the message on get/setparam ioctl with an unknown value.
drm/i915: skip LVDS initialization on Apple Mac Mini
drm/i915: sync SDVO code with stable userland modesetting driver
drm/i915: Unref the object after failing to set tiling mode.
drm/i915: add fence register management to execbuf
drm/i915: Return error from i915_gem_object_get_fence_reg() when failing.
drm/i915: Set up an MTRR covering the GTT at driver load.
drm/i915: Skip SDVO/HDMI init when the chipset tells us it's not present.
drm/i915: Suppress GEM teardown on X Server exit in KMS mode.
drm/radeon: fix ioremap conflict with AGP mappings
i915: fix unneeded locking in i915 LVDS get modes code.
Architectures other than mips and x86 are not using ticket spinlocks.
Therefore, the contention on the lock is meaningless, since there is
nobody known to be waiting on it (arguably /fairly/ unfair locks).
Dummy it out to return 0 on other architectures.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's illegal to call flush_dcache_page on slab pages on a number
of architectures. So this patch avoids doing so if PageSlab is
true.
In future we can move the flush_dcache_page call to those page
cache users that actually need it.
Reported-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Commit 27421e211a, Manually revert
"mlock: downgrade mmap sem while populating mlocked regions", has
introduced its own regression: __mlock_vma_pages_range() may report
an error (for example, -EFAULT from trying to lock down pages from
beyond EOF), but mlock_vma_pages_range() must hide that from its
callers as before.
Reported-by: Sami Farin <safari-kernel@safari.iki.fi>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For historical reason, this driver used its own saving/restoring
of the PCI config space, and used the state of it on resume as
an indication as to whether it needed to re-POST the chip or not.
This methods breaks with the later core changes since the core will
have restored things for us.
This patch fixes it by removing that custom code, using standard
core methods to save/restore state, and testing for the need to
re-POST by comparing the content of a few key PLL registers.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes aty128fb to properly save the PCI config space -before- it
potentially switches the PM state of the chip. This avoids a
warning with the new PM core and is the right thing to do anyway.
I also replaced the hand-coded switch to D2 with a call to the
genericc pci_set_power_state() and removed the code that switches it
back to D0 since the generic code is doing that for us nowadays.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes atyfb to properly save the PCI config space -before- it
potentially switches the PM state of the chip. This avoids a
warning with the new PM core and is the right thing to do anyway.
I also slightly cleaned up the code that checks whether we are
running on a PowerMac to do a runtime check instead of a compile
check only, and replaced a deprecated number with the proper
symbolic constant.
Finally, I removed the useless switch to D0 from resume since
the core does it for us.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
list.h provides a dedicated primitive for
"list_del followed by list_add_tail"... list_move_tail.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Rename the async_*_special() functions to async_*_domain(), which
describes the purpose of these functions much better.
[Broke up long lines to silence checkpatch]
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Add some kerneldoc to the async interface.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
If we fail to create the manager thread, fall back to non-fastboot.
If we fail to create an async thread, try again after waiting for
a bit.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
async_schedule() should pass in async_running as the running
list, and run_one_entry() should put the entry to be run on
the provided running list instead of always on the generic one.
Reported-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Migration helper.
The i915 driver recently added a 'depends on FB' rule to its
Kconfig entry - which silently turns off DRM_I915 if someone
has a working config but no CONFIG_FB selected, and upgrades
to the latest upstream kernel.
Norbert Preining reported this problem:
Bug-Entry : http://bugzilla.kernel.org/show_bug.cgi?id=12599
Subject : dri /dev node disappeared with 2.6.29-rc1
So change it to "select FB", which auto-selects framebuffer
support. This way the driver keeps working, regardless of
whether FB was enabled before or not.
Kconfig select's of interactive options can be problematic to
dependencies and can cause build breakages - but in this case
it's safe because it's a leaf entry with no dependencies of its
own.
( There is some minor circular dependency fallout as FB_I810
and FB_INTEL also used 'depends on FB' constructs - update
those to "select FB" too. )
Reported-by: Norbert Preining <preining@logic.at>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@linux.ie>
As discussed in the long thread about vblank related timeouts, it turns out
GM45 has different frame count registers than previous chips. This patch
adds support for them, which prevents us from waiting on really stale
sequence values in drm_wait_vblank (which rather than returning immediately
ends up timing out or getting interrupted).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In dc1336ff4f (set vblank enable flag correctly
across IRQ uninstall), we made sure drivers that uninstall their interrupt
handler set the vblank enabled flag correctly, so that when interrupts are
re-enabled, vblank interrupts & counts work as expected. However I missed the
last_vblank field: it needs to be updated as well, otherwise, at the next
drm_update_vblank_count we'll end up comparing a current count to a stale
one (the last one captured by the disable function), which may trigger the
wraparound handling, leading to a jumpy counter and hangs in drm_wait_vblank.
The jumpy counter can prevent the DRM_WAIT_ON from returning success if the
difference between the current count and the requested count is greater than
2^23, leading to timeouts or hangs, if the ioctl is restarted in a loop (as
is the case in libdrm < 2.4.4).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Michel Dänzer <michel@daenzer.net>
Tested-by: Timo Aaltonen <tjaalton@cc.hut.fi>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If we failed to allocate a new fence register we would return
VM_FAULT_SIGBUS without relinquishing the lock.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Getting an unknown get/setparam used to be more significant back when they
didn't change much. However, now that we're in the git world we're using
them instead of a monotonic version number to signal feature availability,
so clients ask about unknown params on older kernels more often.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The Apple Mac Mini falsely reports LVDS. Use DMI to check whether we
are running on a Mac Mini, and skip LVDS initialization if that proves
to be the case.
Signed-off-by: Paul Collins <paul@ondioline.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Pull in an update from the 2D driver (hopefully the last one, future work
should be done here and pulled back into xf86-video-intel as needed).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Cleanup the object reference on the error paths.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Adds code to set up fence registers at execbuf time on pre-965 chips as
necessary. Also fixes up a few bugs in the pre-965 tile register support
(get_order != ffs). The number of fences available to the kernel defaults
to the hw limit minus 3 (for legacy X front/back/depth), but a new parameter
allows userspace to override that as needed.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Previously, the caller would continue along without knowing that the
function failed, resulting in potential mis-rendering. Right now vm_fault
just returns SIGBUS in that case, and we may need to disable signal handling
to avoid that happening.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
We'd love to just be using PAT, but even on chips with PAT it gets disabled
sometimes due to an errata. It would probably be better to have pat_enabled
exported and only bother with this when !pat_enabled.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This saves startup time from probing SDVO, and saves setting up HDMI outputs
on G4X devices that don't have them.
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI PM: make the PM core more careful with drivers using the new PM framework
PCI PM: Read power state from device after trying to change it on resume
PCI PM: Do not disable and enable bridges during suspend-resume
PCI: PCIe portdrv: Simplify suspend and resume
PCI PM: Fix saving of device state in pci_legacy_suspend
PCI PM: Check if the state has been saved before trying to restore it
PCI PM: Fix handling of devices without drivers
PCI: return error on failure to read PCI ROMs
PCI: properly clean up ASPM link state on device remove
Impact: fix spurious BUG_ON() triggered under load
module_refcount() isn't reliable outside stop_machine(), as demonstrated
by Karsten Keil <kkeil@suse.de>, networking can trigger it under load
(an inc on one cpu and dec on another while module_refcount() is tallying
can give false results, for example).
Almost noone should be using __module_get, but that's another issue.
Cc: Karsten Keil <kkeil@suse.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (30 commits)
ACPI: Kconfig text - Fix the ACPI_CONTAINER module name according to the real module name.
eeepc-laptop: fix oops when changing backlight brightness during eeepc-laptop init
ACPICA: Fix table entry truncation calculation
ACPI: Enable bit 11 in _PDC to advertise hw coord
ACPI: struct device - replace bus_id with dev_name(), dev_set_name()
ACPI: add missing KERN_* constants to printks
ACPI: dock: Don't eval _STA on every show_docked sysfs read
ACPI: disable ACPI cleanly when bad RSDP found
ACPI: delete CPU_IDLE=n code
ACPI: cpufreq: Remove deprecated /proc/acpi/processor/../performance proc entries
ACPI: make some IO ports off-limits to AML
ACPICA: add debug dump of BIOS _OSI strings
ACPI: proc_dir_entry 'video/VGA' already registered
ACPI: Skip the first two elements in the _BCL package
ACPI: remove BM_RLD access from idle entry path
ACPI: remove locking from PM1x_STS register reads
eeepc-laptop: use netlink interface
eeepc-laptop: Implement rfkill hotplugging in eeepc-laptop
eeepc-laptop: Check return values from rfkill_register
eeepc-laptop: Add support for extended hotkeys
...
During early boot, ACPI RSDT/XSDT table entries are gathered into the
'initial_tables[]' array. This array is currently statically defined (see
./drivers/acpi/tables.c). When there are more table entries than can be
held in the 'initial_tables[]' array, the message "Truncating N table
entries!" is output. As currently implemented, this message will always
erroneously calculate N as 0.
This patch fixes the calculation that determines how many table entries
will be missing (truncated).
This modification may be used under either the GPL or the BSD-style
license used for Intel ACPI CA code.
Signed-off-by: Myron Stowe <myron.stowe@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Bit 11 in intel PDC definitions is meant for OS capability to handle
hardware coordination of P-states. In Linux we have always supported
hwardware coordination of P-states. Just let the BIOSes know that we
support it, by setting this bit.
Some BIOSes use this bit to choose between hardware or software coordination
and without this change below, BIOSes switch to software coordination, which
is not very optimal in terms of power consumption and extra wakeups from idle.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the missing peaces here for the acpi subsystem.
Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Len Brown <len.brown@intel.com>
Some devices trigger a DEVICE_CHECK on every evalutation of _STA. This
can also be seen in commit 8b59560a3b
(ACPI: dock: avoid check _STA method). If an undock is processed, the
dock driver sends a uevent and userspace might read the show_docked
property in sysfs. This causes an evaluation of _STA of the particular
device which causes the dock driver to immediately dock again.
In any case, evaluation of _STA (show_docked) does not necessarily mean
that we are docked, so check with the internal device structure.
http://bugzilla.kernel.org/show_bug.cgi?id=12360
Signed-off-by: Holger Macht <hmacht@suse.de>
Signed-off-by: Len Brown <len.brown@intel.com>
