CONFIG_OMAP_DSP is not in mainline, CONFIG_OMAP_MBOX_FWK is.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Now we use a memory address to store the debug port info, So we need
to read/write this address when we choose DEBUG_LL. When MMU isn't
enable(I.E. the begining part of init stage of the linux kernel boot),
we need to access physical address instead of virtual address,
otherwise the kernel will crash.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds in the necessary clocks and mux pins for UART
control on omap7xx devices. I also made a change in the serial
code to only try and initialize two UARTs in omap_serial_init, as
these devices don't have three.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert most of the magic numbers in mach-omap1/clock_data.c to use
macros. Clean up a few comments to conform with Documentation/CodingStyle.
Mark the current clkops_uart as being OMAP16xx-only, and add some comments
to indicate that it does not belong there, for future cleanup.
This patch should not cause any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add KConfig entry for one of the OMAP1 DVFS rates that was missing it.
Based on the surrounding rate KConfigs and the oscillator frequency,
this patch marks it as valid for all OMAP1 platforms -- Richard,
Tuukka, Tony, perhaps you can comment if this does not look right?
In the long term, all of these CONFIG_OMAP_ARM_*MHZ should be removed.
The OPP settings should be associated with the platform information in
the structure data (perhaps by extending the omap_chip defines). The
selection of which rates to use should be handled at runtime; rates
that are impossible due to xtal frequency mismatch or SoC-type
mismatch should not be included. If implemented correctly, this
should save some CPU time and some memory on OMAP1 kernels.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Reported-by: The VAMOS Research Project <vamos@i4.informatik.uni-erlangen.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tuukka Tikkanen <tuukka.tikkanen@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
APM doesn't exist in Kconfig, therefore removing all references for it
from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_STI doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_DSP doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated to apply on top of already queued patches]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_IR doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
[tony@atomide.com: updated for new mux code]
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP_MUX_ERRORS doesn't exist in Kconfig, therefore replacing all
references for it with OMAP_MUX_WARNINGS in the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we get pin muxing out of plat-omap and can convert H4 to use the
new mux functions.
Note that it should be safe to assume we can mux all the keypad pins
except on H4 which may have Menelaus connected.
Signed-off-by: Tony Lindgren <tony@atomide.com>
remove the section annotation from omap1_clk_disable_unused()
to kill the section mismatch warning.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
These files include linux/bootmem.h without using anything from this
file; remove the unnecessary include.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch adds initialization of FIQ related handlers to the Amstrad Delta
videophone board code. FIQ will be used instead of a traditional IRQ for
processing all GPIO generated interrupts, including a keyboard serial clock
line.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of Amstrad Delta modem utilized GPIO line, interrupt is requested from
standard serial8250 driver code without first requesting the GPIO pin itself.
Even if it works with default OMAP GPIO interrupt handler, it appeared not
compatible with recent, optimized version of the board GPIO FIQ handler,
required for fast processing of interrupts generated by other GPIO pin that a
serial keyboard clock hangs off.
This patch fills the board specific modem initialization routine with common
GPIO line reservation and direction setup.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces an IRQ handler used for processing interrupts generated
by the FIQ handler when it decides there are data ready for processing.
The handler further invokes device specific interrupt routines based on
interrupt source counters passed from the FIQ handler.
The handler setup function is intended to be called from the board
provided init_machine() callback.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
[tony@atomide.com: Updated to include linux/io.h instead of plat/io.h
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch introduces a Fast Interrupt Request (FIQ) handler for Amstrad Delta
(E3) videophone. The handler's purpose is to process interrupts generated by a
GPIO line that a serial keyboard clock hangs off. It collects consecutive bits
into words, pushing them into a buffer, then requests a higher level interrupt
after one or more words are ready for further processing by a keyboard port
driver.
The handler also processes interrupts generated by two other GPIO lines, used
by other on-board supported devices, by simply requesting a higher level
interrupt, that in turn should invoke those device's specific irq handlers.
IRQ12 line, not used by OMAP1510 hardware (described as reserved), has been
choosen as a higher level interrupt source.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This removes the dependency to the UART1 being available for storing
the debug configuration in uncompress.h. This will simplify the
DEBUG_LL UART configuration for boards that may not have UART1, or
have an external UART as it requires only one mapping for DEBUG_LL.
The patch has a few limitations. Basically now we're assuming that
the kernel uncompress code won't overlap with OMAP_UART_INFO. We also
assume the printascii is called at least once before paging_init in
order for addruart to have a chance to read the UART setup from
OMAP_UART_INFO.
As suggested by Cyril Chemparathy <cyril@ti.com>,
Vikram Pandita <vikram.pandita@ti.com> and
Kevin Hilman <khilman@deeprootsystems.com>. Based on an earlier
patch posted for Davinci by Cyril Chemparathy <cyril@ti.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6: (39 commits)
omap: delete unused bootloader tag variables
omap: Devkit8000: Remove unused pins
omap: Devkit8000: Change position of init calls
omap: Devkit8000: Remove unnecessary include file
omap: Devkit8000: Fix typo in pin name
omap: Devkit8000: Add missing package selection
omap: Devkit8000: Fix typo in supplies
n8x0_defconfig: remove CONFIG_NILFS2_FS override
omap: board-sdp-flash.c: Fix typos in debug output
omap4: Fix McBSP4 base address
omap: rx51_defconfig: Remove CONFIG_SYSFS_DEPRECATED*=y options
omap: rx51_defconfig: Remove duplicate phonet
omap: fix a gpmc nand problem
AM3517: initialize i2c subsystem after mux subsystem
omap: remove one of the define of INT_34XX_BENCH_MPU_EMUL
omap: fix the compile error if CONFIG_MTD_NAND_OMAP2 is notenabled
OMAP4: Clocks: Change SPI Instance Names
omap: Devkit8000: Fix wrong usb port on Devkit8000
OMAP4: Fix for CONTROL register Base
OMAP4-HSMMC: FIX for MMC5 Controller IRQ Base
...
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The commit b63128e812 broke the pin muxing
for I2C busses that are enabled from the kernel command line.
Fix this by defining the board registration function omap_register_i2c_bus
in common platform code as it was before but keep the muxing in architecture
dependent files.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP4 platform the iclk control is completly under hardware control
and no software control is available.
This difference w.r.t previous OMAP's needs all the common driver
accross OMAP's , cpu_is_xxxx() checks. To avoid poulluting the
drivers dummy clock nodes are created (The autogeneration
script has been updated accordingly).
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
[paul@pwsan.com: made OMAP1 dummy_ck common and edited patch to reuse that]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The RATE_FIXED clock flag is pointless. In the OMAP1 clock code, it
simply causes the omap1_clk_round_rate() function to return the
current rate of the clock. omap1_clk_round_rate(), however, should
never be called for a fixed-rate clock, since none of these clocks
have a .round_rate function pointer set in their struct clk records.
Similarly, in the OMAP2+ clock code, the RATE_FIXED flag just causes
the clock code to emit a warning if the OMAP clock maintainer was
foolish enough to add a .round_rate function pointer to a fixed-rate
clock. "Doctor, it hurts when I pretend that a fixed-rate clock is
rate-changeable." "Then don't pretend that a fixed-rate clock is
rate-changeable." It has no functional value. This patch drops the
RATE_FIXED clock flag, removing it from all clocks that are so marked.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
After the clkdev conversion, the struct clk.id field became
superfluous, so, drop it. Bring the clock names closer to the TRMs
and ensure they are unique for debugfs.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
use ioremap and remove unused variable to get rid
of compile warnings.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Determine cache size required per McBSP port at init time, based on
processor type running on.
Allocate space for storing cached copies of McBSP register values at
port request.
Modify omap_msbcp_write() function to update the cache with every
register write operation.
Modify omap_mcbsp_read() to support reading from cache or hardware.
Update MCBSP_READ() macro for modified omap_mcbsp_read() function API.
Introduce a new macro that reads from the cache.
Tested on OMAP1510 based Amstrad Delta using linux-omap for-next, commit
fb7380d70e041e4b3892f6b19dff7efb609d15a4 (2.6.33-rc3+ dated 2010-01-11).
Compile-tested with: omap_perseus2_730_defconfig, omap_generic_1610_defconfig,
omap_generic_2420_defconfig, omap_2430sdp_defconfig, omap_3430sdp_defconfig,
omap_4430sdp_defconfig with CONFIG_OMAP_MCBSP=y selected.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OMAP based boards to use physmap-flash. Refreshed against today's
Linux omap kernel tree
Cc: linux-mtd@lists.infradead.org
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Define arch_decomp_setup() the same way as some other
architectures do. Use arch_id to configure the debug uart
based on the machine_is by storing it into the uart
scratchpad register for DEBUG_LL code to use.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This way we don't have conflicts with the defines
with compiling in multiple omaps. Set the addresses
for uarts in struct omap_globals for the early serial
init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise more complicated uart configuration won't be possible.
We can use r1 for tmp register for both head.S and debug.S.
NOTE: This patch depends on another patch to add the the tmp register
into all debug-macro.S files. That can be done with:
$ sed -i -e "s/addruart,rx|addruart, rx/addruart, rx, tmp/"
arch/arm/*/include/*/debug-macro.S
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The armwdt_ck clock uses a fixed divisor, so it can use the OMAP clock
fixed divisor recalculation code, rather than a custom function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 52650505fb caused clock initialization
to fail on OMAP1 with "BUG: spinlock lockup on CPU#0" -- this is because
omap1_select_table_rate() and omap1_round_to_table_rate() call clk_get_rate()
with the clockfw spinlock held. Fix by accessing the rate directly from
the internal clock framework functions.
Thanks to Tony Lindgren <tony@atomide.com> for reporting and testing the fix.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
Commit 52650505fb added an __initdata
decoration to the structure containing the clk_enable and clk_disable
functions. Once init data was freed, these pointers went to null, and
the next enable or disable call caused the kernel to crash. This
change removes this decoration.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: patch manually split and commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This change adds in some missing clocks that were needed as a result
of 526505... (OMAP1 clock: convert mach-omap1/clock.h to
mach-omap1/clock_data.c). Prior to this, it was just assumed that
these clocks existed for all devices, and it was used directly instead
of calling it out with a clock_get call or similar. So, not having
the CK_7XX meant these clocks weren't being used anymore for omap 7xx
devices, which broke things badly.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 35c9049b27 added
drivers/spi/omap_spi_100k.c.
This patch add the related clocks and pin muxing
entries to make the driver work on omap7xx platforms.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch corrects the issue introduced with one of my earlier patches:
OMAP: DMA: Fix omapfb/lcdc on OMAP1510 broken when PM set[1]
as pointed out by OMAP subsystem maintainer.
Applies on top of my prevoius patch:
OMAP: DMA: move LCD DMA related code from plat-omap to mach-omap1[2]
Tested on Amstrad Delta
Compile tested with omap_generic_2420_defconfig
[1] http://patchwork.kernel.org/patch/57922/
[2] http://patchwork.kernel.org/patch/61952/
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds MUX pin configuration and clocks for I2C support
to OMAP 730 and 850-based devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change implements USB client side support into the HTC
Herald board configuration. It uses a similar, but updated
algorithm to initialize the USB as is used in the linwizard
project.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
All of the LCD DMA code in plat-omap/dma.c appears to be OMAP1-only (and
apparently only is available on a subset of OMAP1 chips).
Move this code to mach-omap1/lcd_dma.c.
Tested on OMAP1510 Amstrad Delta.
Compile-tested with omap_generic_2420_defconfig.
Reported-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Reviewed-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since omapnand driver never find its way into mainline, switch to gen_nand instead.
Following patch is compile tested only, but it is based on code I wrote for
NetStar board and runtime tested it there.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Brian Swetland <swetland@google.com>
Cc: Kevin Hilman <kjh@hilman.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use smc91x_platdata to setup smc91x, so we can get rid of OMAP specific stuff
in smc91x driver
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Otherwise we cannot limit new mux code to mach-omap2.
The same signal names should eventually work for other
omaps under mach-omap2.
Note that these pins don't need to be OMAP_PIN_INPUT_PULLUP,
just OMAP_PIN_INPUT is enough.
Cc: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The OMAP1 clock code currently #includes a large .h file full of static
data structures. Instead, define the data in a .c file.
Russell King <linux@arm.linux.org.uk> proposed this new arrangement:
http://marc.info/?l=linux-omap&m=125967425908895&w=2
This patch also deals with most of the flagrant checkpatch violations.
While here, separate the mpu_rate data structures out into their own
files, opp.h and opp_data.c. In the long run, these mpu_rate tables
should be replaced with OPP code.
Also includes a patch from Felipe Balbi <felipe.balbi@nokia.com> to
mark omap1_clk_functions as __initdata to avoid a section warning:
http://patchwork.kernel.org/patch/64366/
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Nishanth Menon <nm@ti.com>
mach-omap1/clock.c:omap1_clk_disable_unused() contains a test that
assumes that the clock structures are available in the file's
namespace. After a following patch, this will no longer be the case.
So we need to reimplement that test. It turns out that we already
have a facility in the clock framework to handle this case - the
ENABLE_ON_INIT flag - used on OMAP2/3. Remove the offending test and
mark the clocks that it was intended to catch as ENABLE_ON_INIT.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some parts of the clock code took advantage of the fact that the statically
allocated clock tree was in clock{,24xx,34xx}.c's local namespace to do some
extra argument checks. These are overzealous and are more difficult to
maintain when the clock tree is in a separate namespace, so, remove them.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Split arch/arm/plat-omap/include/mach/omapfb.h into two files:
include/linux/omapfb.h - ioctls etc for userspace and some kernel
stuff for board files
drivers/video/omap/omapfb.h - for omapfb internal use
This cleans up omapfb.h and also makes it easier for the upcoming new
DSS driver to co-exist with the old driver.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
This patch introduces support for the HTC Herald (T-Mobile
Wing, etc.) series of smart phones -- board support and LCD
panel settings.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The l3_ocpi_ck clock is needed on omap7xx processors for USB.
Additionally, bit 8 of the SOFT_REQ_REG needs to be enabled for
the usb_dc_ck on omap7xx, which is a different bit than that
of the omap16xx-defined clock of the same name.
I added a provision for the usb_dc_ck and l3_ocpi_ck clocks as
dc_clk and hhc_clk, respectively, for omap7xx CPUs. Additionally,
I added a check in machine_without_vbus_sense for all omap7xx
devices, as presently I know of no omap7xx-based devices that
have vbus sense, and it made more sense to me to use a cpu check
here than to spell out each machine one at a time. Finally, DMA
is disabled for omap7xx, as it causes problems with these chips.
Cc: linux-usb@vger.kernel.org
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC mux pins normally used by omap chips in devices.c
are different from what is needed by omap7xx chips. This
change adds a conditional around the mux setup code to
enable the correct mux pins.
The omap730 and omap850 both use a different clock for the "fck"
clock of the MMC interface than other omap processors based on the
SOFT_REQ_REG, pin 12. The "ick" clock is the same as that used
by other omap processors.
* Added the missing clock definition as mmc3_ck to clock.h
* Added the clock definition to omap_clks in clock.c
* Added CK_7XX to the mmci-omap.0 "ick" clock already in clock.c
With these changes, it is now possible to initialize and use MMC
cards with omap730 and omap850 devices.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Eliminate OMAP_MAX_NR_PORTS
Note that also the null terminator entry for omap1
serial_platform_data needs to be now removed to avoid
oopsing.
Note that mach-omap1 uses struct plat_serial8250_port
array, which requires a null terminator at the end,
and that's why we need to use ARRAY_SIZE - 1. This
is not needed on mach-omap2 as the array used is
struct omap_uart_state, and does not use a null
terminator.
Signed-off-by: Alexander Shishkin <virtuoso@slind.org>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
DSP public peripherals used to work on OMAP1510 based (or all OMAP1 class?)
machines as long as old dspgateway code were present in the l-o tree. For
several months it is no longer included, breaking support for McBSP1 based
audio on Amstrad Delta, for example.
This patch, derived from the old dspgateway code, corrects the problem for the
board by simply taking the DSP out of reset state, I guess. That way, things
should not break when a new dsp code is added to the tree, and the change can
be reverted then.
If there are any reports on McBSP1 or other DSP public peripherals not working
for other OMAP1 machines (I've not heard of any for now), I can prepare a more
general patch providing an extra include file with a helper function defined.
Created and tested against linux-2.6.32-rc5
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit 15ac408ee5 removed enabled_uart
and OMAP_TAG_UART. This works for mach-omap2, but causes issues on
mach-omap1 for some boards as the mach-omap1 serial.c was muxing
pins based on the enabled_uart flag for 15xx.
Fix this by muxing pins in board-*.c files for the 15xx boards for
the uart ports that had enabled_uart flag set before the commit
above.
Tested on Amsdtrad Delta only.
Note that in the future we should add support for powering down
the uarts with a timer like mach-omap2/serial.c does. Otherwise
the enabled uarts will be blocking retention-while-idle.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move the remaining headers under plat-omap/include/mach
to plat-omap/include/plat. Also search and replace the
files using these headers to include using the right path.
This was done with:
#!/bin/bash
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
headers=$(cd $mach_dir_old && ls *.h)
omap_dirs="arch/arm/*omap*/ \
drivers/video/omap \
sound/soc/omap"
other_files="drivers/leds/leds-ams-delta.c \
drivers/mfd/menelaus.c \
drivers/mfd/twl4030-core.c \
drivers/mtd/nand/ams-delta.c"
for header in $headers; do
old="#include <mach\/$header"
new="#include <plat\/$header"
for dir in $omap_dirs; do
find $dir -type f -name \*.[chS] | \
xargs sed -i "s/$old/$new/"
done
find drivers/ -type f -name \*omap*.[chS] | \
xargs sed -i "s/$old/$new/"
for file in $other_files; do
sed -i "s/$old/$new/" $file
done
done
for header in $(ls $mach_dir_old/*.h); do
git mv $header $plat_dir_new/
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Create the headers needed for compiling under
mach-omap1/include/mach and mach-omap2/include/mach.
This was done with the following script:
#!/bin/bash
mach_files="clkdev.h gpio.h hardware.h io.h irqs.h memory.h \
smp.h system.h timex.h uncompress.h vmalloc.h"
omaps="mach-omap1 mach-omap2"
mach_dir_old="arch/arm/plat-omap/include/mach"
plat_dir_new="arch/arm/plat-omap/include/plat"
mkdir -p $plat_dir_new
git add $plat_dir_new
for dir in $omaps; do
mach_dir_new="arch/arm/$dir/include/mach"
for header in $mach_files; do
file="$mach_dir_new/$header"
if [ ! -f $file ]; then
echo -ne "/*\n * $file\n */\n\n#include <plat/$header>\n" > $file
git add $file
if [ ! -f $plat_dir_new/$header ]; then
git mv $mach_dir_old/$header $plat_dir_new/$header
fi
fi
done
done
Signed-off-by: Tony Lindgren <tony@atomide.com>
Earlier patch "omap: Remap L3, L4 to get more kernel io address space"
changed the VMALLOC_END.
However, this change causes problems on mach-omap1:
BUG: mapping for 0xe0000000 at 0xe0000000 overlaps vmalloc space
BUG: mapping for 0xe1000000 at 0xe1000000 overlaps vmalloc space
Fix this by creating separate vmalloc.h files for mach-omap1
and mach-omap2.
Signed-off-by: Tony Lindgren <tony@atomide.com>
These clocks are required for booting.
Signed-off-by: Angelo Arrifano <miknix@gmail.com>
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which removes references to omap730 in code
which is shared with omap850, replacing them with references to omap7xx.
This updates all the remaining omap730 references in miscellaneous local
variables, macros and similar.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which removes references to omap730 in code
which is shared with omap850, replacing them with references to omap7xx.
Turns INT_730_* to INT_7XX_* for definitions in irqs.h and all users.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which removes references to omap730 in code
which is shared with omap850, replacing them with references to omap7xx.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
This file had no omap850 specific code. Initial clock support was done in
the Linwizard tree by Zebediah C. McClure.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
This file had no omap850 specific code. Original omap850 support in Linwizard
was done by cloning the omap730 code. That work was done by Zebediah C. McClure.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
This fixes a bug which prevents IRQs from being enabled on omap850 due to
a missing check in entry-macro.S, which was found by Cory Maccarrone.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
This patch is part of a series which unifies all duplicated code between
omap730 and omap850. All cpu checks are converted to cpu_is_omap7xx() and
CONFIG_ARCH_OMAP850 is added to all CONFIG_ARCH_OMAP730 checks.
Signed-off-by: Alistair Buxton <a.j.buxton@gmail.com>
Reviewed-by: Zebediah C. McClure <zmc@lurian.net>
Original message:
The previous value of the jtag_id was set for the omap730. For the
omap850, this value is different, and this was causing
autodetection to fail.
Reported-by:
Cory Maccarrone <darkstar6262@gmail.com>
Angelo Arrifano <miknix@gmail.com>
Alistair Buxton <a.j.buxton@gmail.com>
Signed-off-by: Angelo Arrifano <miknix@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP tags are deprecrated so drop them.
Drop UART config data which decides which UARTs to enable during boot.
This is no longer necessary since serial core code disables clocks
after inactivity.
Background: with new UART idle code, all on-chip UARTs are idled using
a configurable inactivity timer (default 5 seconds.) After the
inactivity timer, UART clocks are disabled automatically.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Search and replace OMAP_IO_ADDRESS with OMAP1_IO_ADDRESS and OMAP2_IO_ADDRESS,
and convert omap_read/write into a functions instead of a macros.
Also rename OMAP_MPUIO_VBASE to OMAP1_MPUIO_VBASE.
In the long run, most code should use ioremap + __raw_read/write instead.
Signed-off-by: Tony Lindgren <tony@atomide.com>
fix the following 'make includecheck' warning:
arch/arm/mach-omap1/mcbsp.c: mach/irqs.h is included more than once.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Some of the N770's MMC configuration options seem to have been
dropped. This patch adds them back in again.
Note that only the .ocr_mask change was /critical/, but I've added the
.max_freq setting back as well, as the original sources had it. Can
anyone confirm if this is unnecessary?
Secondly, there is support in the original code for a 4wire/higher
speed mode. As I don't have the requisite N770 hardware (I think it
was a rev2 N770?) to test this, I can't really add it back.
Signed-off-by: Andrew de Quincey <adq@lidskialf.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This fixes the positioning of " in MODULE_AUTHOR, which is currently
causing a build failure on latest git with CONFIG_OMAP_MBOX_FWK=m; the
original breakage appears to date from the end of last year in
a5abbbe52b7e89a7633319c5417bd4331f7ac8ed
Signed-Off-By: Jonathan McDowell <noodles@earth.li>
Acked-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make 770 LCD work by adding clk_add_alias().
Also remove the old unused functions.
Note that the clk_add_alias() could probably be moved
to arch/arm/clkdev.c later on.
Cc: linux-fbdev-devel@lists.sourceforge.net
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com
Update OMAP1-specific PM infrastructure. This is a sync of what is in
linux-omap for OMAP1.
This mostly de-couples OMAP1 PM from OMAP2/3 PM and renames things
accordingly, and removes omap2/3 specific code from OMAP1 specific
headers.
Original OMAP1 decoupling patch for OMAP PM branch by Paul Walmsley.
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch is to sync the core linux-omap PM code with mainline. This
code has evolved and been used for a while the linux-omap tree, but
the attempt here is to finally get this into mainline.
Following this will be a series of patches from the 'PM branch' of the
linux-omap tree to add full PM hardware support from the linux-omap
tree.
Much of this PM core code was written by Jouni Hogander with
significant contributions from Paul Walmsley as well as many others
from Nokia, Texas Instruments and linux-omap community.
Signed-off-by: Jouni Hogander <jouni.hogander@nokia.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Rename clk_init_one() to clk_preinit() to distinguish its function
from clk_init() and the individual struct clk init functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Typo error when requesting for clock for dsp in omap1
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This should be done with GPIO calls. Patches against the
mainline tree welcome to add the necessary working functionality
back.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OMAP_TAGS should vanish soon since they're not generic arm tags.
Most of them can be converted to a platform_data or parsed
from a command line like e.g. serial tag.
For OMAP_TAG_USB we just let boards call omap_usb_init()
passing a pointer to omap_usb_config.
Patch updated by Tony for mainline, basically make
n770 and h4 compile. Also folded in a fix for OSK
by David Brownell <dbrownell@users.sourceforge.net>.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
linux-omap source commit 33d000c99ee393fe2042f93e8422f94976d276ce
introduces a way to "dry run" clock changes before they're committed.
However, this involves putting logic to handle this into each and
every recalc function, and unfortunately due to the caching, led to
some bugs.
Solve both of issues by making the recalc methods always return the
clock rate for the clock, which the caller decides what to do with.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Traditionally, we've tracked the parent/child relationships between
clk structures by setting the child's parent member to point at the
upstream clock. As a result, when decending the tree, we have had
to scan all clocks to find the children.
Avoid this wasteful scanning by keeping a list of the clock's children.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes booting, and is a step toward fixing things properly:
- Make enable_reg u32 instead of u16
[rmk: virtual addresses are void __iomem *, not u32]
- Get rid of VIRTUAL_IO_ADDRESS for clocks
- Use __raw_read/write instead of omap_read/write for clock registers
This patch adds a bunch of compile warnings until omap1 clock
also uses offsets.
linux-omap source commit is 9d1dff8638c9e96a401e1885f9948662e9ff9636.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... which now means no driver requests the "armxor_ck" clock directly.
Also, fix the error handling for clk_get(), ensuring that we propagate
the error returned from clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By providing a dummy ick for OMAP1510 and OMAP310, we avoid having
SoC conditional clock information in i2c-omap.c. Also, fix the
error handling by making sure we propagate the error returned via
clk_get().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than introducing a special 'mcbsp_clk' with code behind it in
mach-omap*/mcbsp.c to handle the SoC specifics, arrange for the mcbsp
driver to be like any other driver. mcbsp requests its fck and ick
clocks directly, and the SoC specific code deals with selecting the
correct clock.
There is one oddity to deal with - OMAP1 fiddles with the DSP clocks
and DSP reset, so we move this to the two callback functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert OMAP MMC driver to match clocks using the device ID and a
connection ID rather than a clock name. This allows us to eliminate
the OMAP1/OMAP2 differences for the function clock.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
By providing a dummy clock node, we can eliminate the SoC conditional
clock handing in the OMAP drivers, moving this knowledge out of the
driver and into the machine clock support code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It makes no sense to have the CKCTL rate selection implemented as a flag
and a special exception in the top level set_rate/round_rate methods.
Provide CKCTL set_rate/round_rate methods, and use these for where ever
RATE_CKCTL is used and they're not already overridden. This allows us
to remove the RATE_CKCTL flag.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
propagate_rate() is recursive, so it makes sense to minimise the
amount of stack which is used for each recursion. So, rather than
recursing back into it from the ->recalc functions if RATE_PROPAGATES
is set, do that test at the higher level.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We've always called propagate_rate() in the parent function to
the .set_rate methods, so there's no point having the .set_rate
methods also call this heavy-weight function - it's mere
duplication of what's happening elsewhere.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the clock propagation calls for set_parent and set_rate into
the core omap clock code, rather than having these calls scattered
throughout the OMAP1 and OMAP2 implementations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
... and use it for clocks which are ALWAYS_ENABLED. These clocks
use a non-NULL enable_reg pointer for other purposes (such as
selecting clock rates.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Collect up all the common enable/disable clock operation functions
into a separate operations structure.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The naming accidentally broke while changing the name for the
driver to not to conflict with the other mmc driver.
Signed-off-by: Tony Lindgren <tony@atomide.com>
A spin_lock deadlock will occur when omap_mcbsp_request() is invoked.
omap_mcbsp_request()
\- clk_enable(mcbsp->clk) [takes and holds clockfw_lock]
\- omap2_clk_enable()
\- _omap2_clk_enable()
\- omap_mcbsp_clk_enable()
\- clk_enable(child clock) [tries for clockfw_lock again]
mcbsp_clk is a virtual clock and it comprises several child clocks. when
enable mcbsp_clk in omap_mcbsp_request(), the enable function of mcbsp_clk
will enable its child clocks, then the deadlock occurs.
The solution is to remove the virtual clock and enable these child clocks in
omap_mcbsp_request() directly.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes old platform devices. Alsa should now
be using the ASoC driver. For boards not yet using ASoC,
please see sound/soc/omap/osk5912.c.
Add dummy aic23_power_up and aic23_power_down functions for 770
to keep things compiling.
Remove references to omap_gpio_switch, and unused h2_nand_dev_ready
function.
This patch is based on an earlier patch by Arun KS.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding I2C board info is required for tlvaic23 i2c chip driver.
Cc: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Arun KS <arunks@mistralsolutions.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix compile by removing remaining omap specific gpio
calls. Based on earlier patches by Jarkko Nikula.
Also remove old GPIO key code, there is already a patch
to do this with gpio_keys.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove old MMC platform init code accidentally
left behind.
Patches are welcome to the new style MMC init code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
arch/arm/mach-at91/at91cap9.c:337: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91rm9200.c:301: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9260.c:351: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9261.c:287: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9263.c:312: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-at91/at91sam9rl.c:304: error: 'NR_AIC_IRQS' undeclared here (not in a function)
arch/arm/mach-h720x/h7202-eval.c:38: error: implicit declaration of function 'IRQ_CHAINED_GPIOB'
arch/arm/mach-ks8695/devices.c:46: error: 'KS8695_IRQ_WAN_RX_STATUS' undeclared here (not in a function)
arch/arm/mach-msm/devices.c:28: error: 'INT_UART1' undeclared here (not in a function)
arch/arm/mach-mx2/devices.c:233: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-mx3/devices.c:128: error: 'MXC_GPIO_IRQ_START' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:140: error: 'INT_730_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:165: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap1/mcbsp.c:200: error: 'INT_McBSP1RX' undeclared here (not in a function)
arch/arm/mach-omap2/board-apollon.c:286: error: implicit declaration of function 'omap_set_gpio_direction'
arch/arm/mach-omap2/mcbsp.c:154: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-omap2/mcbsp.c:181: error: 'INT_24XX_MCBSP1_IRQ_RX' undeclared here (not in a function)
arch/arm/mach-pxa/e350.c:36: error: 'IRQ_BOARD_START' undeclared here (not in a function)
arch/arm/plat-s3c/dev-i2c0.c:32: error: 'IRQ_IIC' undeclared here (not in a function)
...
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
