We currently enforce the !RW mapping for the kernel mapping that maps
holes between different text, rodata and data sections. However, kernel
identity mappings will have different RWX permissions to the pages mapping to
text and to the pages padding (which are freed) the text, rodata sections.
Hence kernel identity mappings will be broken to smaller pages. For 64-bit,
kernel text and kernel identity mappings are different, so we can enable
protection checks that come with CONFIG_DEBUG_RODATA, as well as retain 2MB
large page mappings for kernel text.
Konrad reported a boot failure with the Linux Xen paravirt guest because of
this. In this paravirt guest case, the kernel text mapping and the kernel
identity mapping share the same page-table pages. Thus forcing the !RW mapping
for some of the kernel mappings also cause the kernel identity mappings to be
read-only resulting in the boot failure. Linux Xen paravirt guest also
uses 4k mappings and don't use 2M mapping.
Fix this issue and retain large page performance advantage for native kernels
by not working hard and not enforcing !RW for the kernel text mapping,
if the current mapping is already using small page mapping.
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1266522700.2909.34.camel@sbs-t61.sc.intel.com>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: stable@kernel.org [2.6.32, 2.6.33]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Version 4: use get_irq_chip_data() in destroy_irq() to get rid of some
local vars.
When two drivers are setting up MSI-X at the same time via
pci_enable_msix() there is a race. See this dmesg excerpt:
[ 85.170610] ixgbe 0000:02:00.1: irq 97 for MSI/MSI-X
[ 85.170611] alloc irq_desc for 99 on node -1
[ 85.170613] igb 0000:08:00.1: irq 98 for MSI/MSI-X
[ 85.170614] alloc kstat_irqs on node -1
[ 85.170616] alloc irq_2_iommu on node -1
[ 85.170617] alloc irq_desc for 100 on node -1
[ 85.170619] alloc kstat_irqs on node -1
[ 85.170621] alloc irq_2_iommu on node -1
[ 85.170625] ixgbe 0000:02:00.1: irq 99 for MSI/MSI-X
[ 85.170626] alloc irq_desc for 101 on node -1
[ 85.170628] igb 0000:08:00.1: irq 100 for MSI/MSI-X
[ 85.170630] alloc kstat_irqs on node -1
[ 85.170631] alloc irq_2_iommu on node -1
[ 85.170635] alloc irq_desc for 102 on node -1
[ 85.170636] alloc kstat_irqs on node -1
[ 85.170639] alloc irq_2_iommu on node -1
[ 85.170646] BUG: unable to handle kernel NULL pointer dereference
at 0000000000000088
As you can see igb and ixgbe are both alternating on create_irq_nr()
via pci_enable_msix() in their probe function.
ixgbe: While looping through irq_desc_ptrs[] via create_irq_nr() ixgbe
choses irq_desc_ptrs[102] and exits the loop, drops vector_lock and
calls dynamic_irq_init. Then it sets irq_desc_ptrs[102]->chip_data =
NULL via dynamic_irq_init().
igb: Grabs the vector_lock now and starts looping over irq_desc_ptrs[]
via create_irq_nr(). It gets to irq_desc_ptrs[102] and does this:
cfg_new = irq_desc_ptrs[102]->chip_data;
if (cfg_new->vector != 0)
continue;
This hits the NULL deref.
Another possible race exists via pci_disable_msix() in a driver or in
the number of error paths that call free_msi_irqs():
destroy_irq()
dynamic_irq_cleanup() which sets desc->chip_data = NULL
...race window...
desc->chip_data = cfg;
Remove the save and restore code for cfg in create_irq_nr() and
destroy_irq() and take the desc->lock when checking the irq_cfg.
Reported-and-analyzed-by: Brandon Philips <bphilips@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <20100207210250.GB8256@jenkins.home.ifup.org>
Signed-off-by: Brandon Phiilps <bphilips@suse.de>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
On the iMac9,1 /sbin/reboot results in a black mangled screen. Adding
this DMI entry gets the machine to reboot cleanly as it should.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
LKML-Reference: <1266362249-3337-1-git-send-email-justinmattock@gmail.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Thomas Renninger <trenn@suse.de> reported on IBM x3330
booting a latest kernel on this machine results in:
PCI: PCI BIOS revision 2.10 entry at 0xfd61c, last bus=1
PCI: Using configuration type 1 for base access bio: create slab <bio-0> at 0
ACPI: SCI (IRQ30) allocation failed
ACPI Exception: AE_NOT_ACQUIRED, Unable to install System Control Interrupt handler (20090903/evevent-161)
ACPI: Unable to start the ACPI Interpreter
Later all kind of devices fail...
and bisect it down to this commit:
commit b9c61b7007
x86/pci: update pirq_enable_irq() to setup io apic routing
it turns out we need to set irq routing for the sci on ioapic1 early.
-v2: make it work without sparseirq too.
-v3: fix checkpatch.pl warning, and cc to stable
Reported-by: Thomas Renninger <trenn@suse.de>
Bisected-by: Thomas Renninger <trenn@suse.de>
Tested-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
LKML-Reference: <1265793639-15071-2-git-send-email-yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Do not set current->mm->mmap to NULL in 32-bit emulation on 64-bit
load_aout_binary after flush_old_exec as it would destroy already
set brpm mapping with arguments.
Introduced by b6a2fea393
mm: variable length argument support
where the argument mapping in bprm was added.
[ hpa: this is a regression from 2.6.22... time to kill a.out? ]
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
LKML-Reference: <1265831716-7668-1-git-send-email-jslaby@suse.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ollie Wild <aaw@google.com>
Cc: x86@kernel.org
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
We need to fall back from logical-flat APIC mode to physical-flat mode
when we have more than 8 CPUs. However, in the presence of CPU
hotplug(with bios listing not enabled but possible cpus as disabled cpus in
MADT), we have to consider the number of possible CPUs rather than
the number of current CPUs; otherwise we may cross the 8-CPU boundary
when CPUs are added later.
32bit apic code can use more cleanups (like the removal of vendor checks in
32bit default_setup_apic_routing()) and more unifications with 64bit code.
Yinghai has some patches in works already. This patch addresses the boot issue
that is reported in the virtualization guest context.
[ hpa: incorporated function annotation feedback from Yinghai Lu ]
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
LKML-Reference: <1265767304.2833.19.camel@sbs-t61.sc.intel.com>
Acked-by: Shaohui Zheng <shaohui.zheng@intel.com>
Reviewed-by: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both x86-32 and x86-64 with 32-bit compat use ARCH_DLINFO_IA32,
which defines two saved_auxv entries. But system.h only defines
AT_VECTOR_SIZE_ARCH as 2 for CONFIG_IA32_EMULATION, not for
CONFIG_X86_32. Fix that.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
LKML-Reference: <20100209023502.GA15408@us.ibm.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This fixes the regression introduced by commit
42590a7501 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").
The commit 61684ceaad fixed the
above regression but it's not enough. When amd64-agp is built as
a module, AGP isn't initialized, iommu is initialized, all the
aperture is owned by the iommu.
Reported-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
LKML-Reference: <20100204090802S.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix minor spelling error in comment. No code change.
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
LKML-Reference: <201002022238.o12McDiF018720@imap1.linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
cfq-iosched: Do not idle on async queues
blk-cgroup: Fix potential deadlock in blk-cgroup
block: fix bugs in bio-integrity mempool usage
block: fix bio_add_page for non trivial merge_bvec_fn case
drbd: null dereference bug
drbd: fix max_segment_size initialization
Improve handling of fragmented per-CPU vmaps. We previously don't free
up per-CPU maps until all its addresses have been used and freed. So
fragmented blocks could fill up vmalloc space even if they actually had
no active vmap regions within them.
Add some logic to allow all CPUs to have these blocks purged in the case
of failure to allocate a new vm area, and also put some logic to trim
such blocks of a current CPU if we hit them in the allocation path (so
as to avoid a large build up of them).
Christoph reported some vmap allocation failures when using the per CPU
vmap APIs in XFS, which cannot be reproduced after this patch and the
previous bug fix.
Cc: linux-mm@kvack.org
Cc: stable@kernel.org
Tested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
--
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
RCU list walking of the per-cpu vmap cache was broken. It did not use
RCU primitives, and also the union of free_list and rcu_head is
obviously wrong (because free_list is indeed the list we are RCU
walking).
While we are there, remove a couple of unused fields from an earlier
iteration.
These APIs aren't actually used anywhere, because of problems with the
XFS conversion. Christoph has now verified that the problems are solved
with these patches. Also it is an exported interface, so I think it
will be good to be merged now (and Christoph wants to get the XFS
changes into their local tree).
Cc: stable@kernel.org
Cc: linux-mm@kvack.org
Tested-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Nick Piggin <npiggin@suse.de>
--
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'sh/for-2.6.33' of git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
sh: Fix access to released memory in clk_debugfs_register_one()
sh: Fix access to released memory in dwarf_unwinder_cleanup()
usb: r8a66597-hdc disable interrupts fix
spi: spi_sh_msiof: Fixed data sampling on the correct edge
Commit 221af7f87b ("Split 'flush_old_exec' into two functions") split
the function at the point of no return - ie right where there were no
more error cases to check. That made sense from a technical standpoint,
but when we then also combined it with the actual personality setting
going in between flush_old_exec() and setup_new_exec(), it needs to be a
bit more careful.
In particular, we need to make sure that we really flush the old
personality bits in the 'flush' stage, rather than later in the 'setup'
stage, since otherwise we might be flushing the _new_ personality state
that we're just setting up.
So this moves the flags and personality flushing (and 'flush_thread()',
which is the arch-specific function that generally resets lazy FP state
etc) of the old process into flush_old_exec(), so that it doesn't affect
any state that execve() is setting up for the new process environment.
This was reported by Michal Simek as breaking his Microblaze qemu
environment.
Reported-and-tested-by: Michal Simek <michal.simek@petalogix.com>
Cc: Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Few weeks back, Shaohua Li had posted similar patch. I am reposting it
with more test results.
This patch does two things.
- Do not idle on async queues.
- It also changes the write queue depth CFQ drives (cfq_may_dispatch()).
Currently, we seem to driving queue depth of 1 always for WRITES. This is
true even if there is only one write queue in the system and all the logic
of infinite queue depth in case of single busy queue as well as slowly
increasing queue depth based on last delayed sync request does not seem to
be kicking in at all.
This patch will allow deeper WRITE queue depths (subjected to the other
WRITE queue depth contstraints like cfq_quantum and last delayed sync
request).
Shaohua Li had reported getting more out of his SSD. For me, I have got
one Lun exported from an HP EVA and when pure buffered writes are on, I
can get more out of the system. Following are test results of pure
buffered writes (with end_fsync=1) with vanilla and patched kernel. These
results are average of 3 sets of run with increasing number of threads.
AVERAGE[bufwfs][vanilla]
-------
job Set NR ReadBW(KB/s) MaxClat(us) WriteBW(KB/s) MaxClat(us)
--- --- -- ------------ ----------- ------------- -----------
bufwfs 3 1 0 0 95349 474141
bufwfs 3 2 0 0 100282 806926
bufwfs 3 4 0 0 109989 2.7301e+06
bufwfs 3 8 0 0 116642 3762231
bufwfs 3 16 0 0 118230 6902970
AVERAGE[bufwfs] [patched kernel]
-------
bufwfs 3 1 0 0 270722 404352
bufwfs 3 2 0 0 206770 1.06552e+06
bufwfs 3 4 0 0 195277 1.62283e+06
bufwfs 3 8 0 0 260960 2.62979e+06
bufwfs 3 16 0 0 299260 1.70731e+06
I also ran buffered writes along with some sequential reads and some
buffered reads going on in the system on a SATA disk because the potential
risk could be that we should not be driving queue depth higher in presence
of sync IO going to keep the max clat low.
With some random and sequential reads going on in the system on one SATA
disk I did not see any significant increase in max clat. So it looks like
other WRITE queue depth control logic is doing its job. Here are the
results.
AVERAGE[brr, bsr, bufw together] [vanilla]
-------
job Set NR ReadBW(KB/s) MaxClat(us) WriteBW(KB/s) MaxClat(us)
--- --- -- ------------ ----------- ------------- -----------
brr 3 1 850 546345 0 0
bsr 3 1 14650 729543 0 0
bufw 3 1 0 0 23908 8274517
brr 3 2 981.333 579395 0 0
bsr 3 2 14149.7 1175689 0 0
bufw 3 2 0 0 21921 1.28108e+07
brr 3 4 898.333 1.75527e+06 0 0
bsr 3 4 12230.7 1.40072e+06 0 0
bufw 3 4 0 0 19722.3 2.4901e+07
brr 3 8 900 3160594 0 0
bsr 3 8 9282.33 1.91314e+06 0 0
bufw 3 8 0 0 18789.3 23890622
AVERAGE[brr, bsr, bufw mixed] [patched kernel]
-------
job Set NR ReadBW(KB/s) MaxClat(us) WriteBW(KB/s) MaxClat(us)
--- --- -- ------------ ----------- ------------- -----------
brr 3 1 837 417973 0 0
bsr 3 1 14357.7 591275 0 0
bufw 3 1 0 0 24869.7 8910662
brr 3 2 1038.33 543434 0 0
bsr 3 2 13351.3 1205858 0 0
bufw 3 2 0 0 18626.3 13280370
brr 3 4 913 1.86861e+06 0 0
bsr 3 4 12652.3 1430974 0 0
bufw 3 4 0 0 15343.3 2.81305e+07
brr 3 8 890 2.92695e+06 0 0
bsr 3 8 9635.33 1.90244e+06 0 0
bufw 3 8 0 0 17200.3 24424392
So looks like it might make sense to include this patch.
Thanks
Vivek
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Linux kernel 2.6.32 and later allocate address space from the top of the
kernel virtual memory address space.
This patch implements virtual memory size detection for 64 bit MIPS CPUs
to avoid resulting crashes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/935/
Reviewed-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch improves disable_controller() in the r8a66597-hdc
driver to disable all interrupts and clear status flags. It
also makes sure that disable_controller() is called during
probe(). This fixes the relatively rare case of unexpected
pending interrupts after kexec reboot.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The spi_sh_msiof.c driver presently misconfigures REDG and TEDG. TEDG==0
outputs data at the **rising edge** of the clock and REDG==0 samples data
at the **falling edge** of the clock. Therefore for SPI, TEDG must be
equal to REDG, otherwise the last byte received is not sampled in SPI
mode 3.
This brings the driver in line with the SH7723 HW Reference Manual
settings documented in Figures 20.20 and 20.21 ("SPI Clock and data
timing").
Signed-off-by: Markus Pietrek <Markus.Pietrek@emtrion.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The previous changeset left behind an unused inode variable.
This patch removes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
As the padlock driver for SHA uses a software fallback to perform
partial hashing, it must implement custom import/export functions.
Otherwise hmac which depends on import/export for prehashing will
not work with padlock-sha.
Reported-by: Wolfgang Walter <wolfgang.walter@stwm.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
No other driver does anything remotely like this that I know of except
for the tty drivers, and I can't see any reason for random/urandom to do
it. In fact, it's a (trivial, harmless) timing information leak. And
obviously, it generates power- and flash-cycle wasting I/O, especially
if combined with something like hwrngd. Also, it breaks ubifs's
expectations.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
DBDMA descriptors need to be located at 32-byte aligned addresses;
however kmalloc in conjunction with the SLAB allocator and
CONFIG_DEBUG_SLUB enabled doesn't deliver any. The dbdma code works
around that by allocating a larger area and realigning the start
address within it.
When freeing a channel however this adjustment is not taken into
account which results in an oops:
Kernel bug detected[#1]:
[...]
Call Trace:
[<80186010>] cache_free_debugcheck+0x284/0x318
[<801869d8>] kfree+0xe8/0x2a0
[<8010b31c>] au1xxx_dbdma_chan_free+0x2c/0x7c
[<80388dc8>] au1x_pcm_dbdma_free+0x34/0x4c
[<80388fa8>] au1xpsc_pcm_close+0x28/0x38
[<80383cb8>] soc_codec_close+0x14c/0x1cc
[<8036dbb4>] snd_pcm_release_substream+0x60/0xac
[<8036dc40>] snd_pcm_release+0x40/0xa0
[<8018c7a8>] __fput+0x11c/0x228
[<80188f60>] filp_close+0x7c/0x98
[<80189018>] sys_close+0x9c/0xe4
[<801022a0>] stack_done+0x20/0x3c
Fix this by recording the address delivered by kmalloc() and using
it as parameter to kfree().
This fix is only necessary with the SLAB allocator and CONFIG_DEBUG_SLAB
enabled; non-debug SLAB, SLUB do return nicely aligned addresses,
debug-enabled SLUB currently panics early in the boot process.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/878/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ASoC: AM3517: ASoC driver not getting compiled
ASoC: AIC23: Fixing writes to non-existing registers in resume function
ALSA: hda - Add an ASUS mobo to MSI blacklist
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms: Fix oops after radeon_cs_parser_init() failure.
drm/radeon/kms: move radeon KMS on/off switch out of staging.
drm/radeon/kms: Bailout of blit if error happen & protect with mutex V3
drm/vmwgfx: Don't send bad flags to the host
drm/vmwgfx: Request SVGA version 2 and bail if not found
drm/vmwgfx: Correctly detect 3D
drm/ttm: remove unnecessary save_flags and ttm_flag_masked in ttm_bo_util.c
drm/kms: Remove incorrect comment in struct drm_mode_modeinfo
drm/ttm: remove padding from ttm_ref_object on 64bit builds
drm/radeon/kms: release agp on error.
drm/kms/radeon/agp: Move the check of the aper_size after drm_acp_acquire and drm_agp_info
drm/kms/radeon/agp: Fix warning, format ‘%d’ expects type ‘int’, but argument 4 has type ‘size_t’
drm/ttm: Avoid conflicting reserve_memtype during ttm_tt_set_page_caching.
drm/kms/radeon: pick digitial encoders smarter. (v3)
drm/radeon/kms: use active device to pick connector for encoder
drm/radeon/kms: fix incorrect logic in DP vs eDP connector checking.
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf, hw_breakpoint, kgdb: Do not take mutex for kernel debugger
x86, hw_breakpoints, kgdb: Fix kgdb to use hw_breakpoint API
hw_breakpoints: Release the bp slot if arch_validate_hwbkpt_settings() fails.
perf: Ignore perf.data.old
perf report: Fix segmentation fault when running with '-g none'
* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: Correct printk whitespace in warning from cpu down task check
sched: Fix incorrect sanity check
sched: Fix fork vs hotplug vs cpuset namespaces
* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing/documentation: Cover new frame pointer semantics
tracing/documentation: Fix a typo in ftrace.txt
ring-buffer: Check for end of page in iterator
ring-buffer: Check if ring buffer iterator has stale data
tracing: Prevent kernel oops with corrupted buffer
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86/agp: Fix agp_amd64_init regression
x86: Add quirk for Intel DG45FC board to avoid low memory corruption
x86: Add Dell OptiPlex 760 reboot quirk
x86, UV: Fix RTC latency bug by reading replicated cachelines
oprofile/x86: add Xeon 7500 series support
oprofile/x86: fix crash when profiling more than 28 events
lib/dma-debug.c: mark file-local struct symbol static.
x86/amd-iommu: Fix deassignment of a device from the pt_domain
x86/amd-iommu: Fix IOMMU-API initialization for iommu=pt
x86/amd-iommu: Fix NULL pointer dereference in __detach_device()
x86/amd-iommu: Fix possible integer overflow
The WM8350 LED driver needs to be able to enable and disable the
regulators it is using. Previously the core wasn't properly enforcing
status change constraints so the driver was able to function but this
has always been intended to be required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
ince gfs2 writes the rindex file a block at a time, and releases the
exclusive lock after each block, it is possible that another process
will grab the lock in the middle of the write. Since rindex entries are
not an even divisor of blocks, that other process may see partial
entries. On grows, this is fine. The process can simply ignore the the
partial entires. Previously, the code withdrew when it saw partial
entries. Now it simply ignores them.
Signed-off-by: Benjamin Marzinski <bmarzins@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Here are the powerpc bits to remove TIF_ABI_PENDING now that
set_personality() is called at the appropriate place in exec.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If radeon_cs_parser_init() fails, radeon_cs_ioctl() calls
radeon_cs_parser_fini() with the non-zero error value. The latter dereferenced
parser->ib which hasn't been initialized yet -> boom. Add a test for parser->ib
being non-NULL before dereferencing it.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
desc->affinity doesn't exit in that case. Let's use a macro for
the UP variant of get_irq_server(), it's the easiest way, avoids
evaluating arguments.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We are happy enough that the KMS driver is stable enough for enough people
for the kms enable/disable to leave staging. Distros can now contemplate
turning this on.
Signed-off-by: Dave Airlie <airlied@redhat.com>
If an error happen in r600_blit_prepare_copy report it rather
than WARNING and keeping execution. For instance if ib allocation
failed we did just warn about but then latter tried to access
NULL ib ptr causing oops. This patch also protect r600_copy_blit
with a mutex as otherwise one process might overwrite blit temporary
data with new one possibly leading to GPU lockup.
Should partialy or totaly fix:
https://bugzilla.redhat.com/show_bug.cgi?id=553279
V2 failing blit initialization is not fatal, fallback to memcpy when
this happen
V3 init blit before startup as we pin in startup, remove duplicate
code (this one was actualy tested unlike V2)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
