kevin/linux
1
Fork 0
Code
e6604a7fd7
linux/drivers/usb/host/ehci-fsl.c
Christian Engelmayer e6604a7fd7 EHCI: Quirk flag for port power handling on overcurrent. 
Commit 756aa6b3d5 (ehci-hub: improved
over-current recovery) added port power cycling on overcurrent indications as
needed by the MPC8349 USB controller after resolving of the overcurrent
situation in order to have the host state machine assert the correct port
status again.

Commit 81463c1d70 (EHCI: only power off port if
over-current is active) solved a thus resulting issue of endless overcurrent
changes in combination with the MAX4967 USB power supply chip that signals
overcurrent when power is not enabled by only powering off a port if the
overcurrent is currently active.

Added quirks flag need_oc_pp_cycle in order to specify the needed behaviour as
there is no common behaviour that can comply with both requirements.
Activated the quirks handling for Freescale 83xx based boards.

Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2013-04-03 11:38:53 -07:00

738 lines
19 KiB
C
Raw Blame History

/*
* Copyright 2005-2009 MontaVista Software, Inc.
* Copyright 2008,2012 Freescale Semiconductor, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
* for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software Foundation,
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*
* Ported to 834x by Randy Vinson <rvinson@mvista.com> using code provided
* by Hunter Wu.
* Power Management support by Dave Liu <daveliu@freescale.com>,
* Jerry Huang <Chang-Ming.Huang@freescale.com> and
* Anton Vorontsov <avorontsov@ru.mvista.com>.
*/
#include <linux/kernel.h>
#include <linux/types.h>
#include <linux/delay.h>
#include <linux/pm.h>
#include <linux/err.h>
#include <linux/platform_device.h>
#include <linux/fsl_devices.h>
#include "ehci-fsl.h"
/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */
/**
* usb_hcd_fsl_probe - initialize FSL-based HCDs
* @drvier: Driver to be used for this HCD
* @pdev: USB Host Controller being probed
* Context: !in_interrupt()
*
* Allocates basic resources for this USB host controller.
*
*/
static int usb_hcd_fsl_probe(const struct hc_driver *driver,
struct platform_device *pdev)
{
struct fsl_usb2_platform_data *pdata;
struct usb_hcd *hcd;
struct resource *res;
int irq;
int retval;
pr_debug("initializing FSL-SOC USB Controller\n");
/* Need platform data for setup */
pdata = (struct fsl_usb2_platform_data *)pdev->dev.platform_data;
if (!pdata) {
dev_err(&pdev->dev,
"No platform data for %s.\n", dev_name(&pdev->dev));
return -ENODEV;
}
/*
* This is a host mode driver, verify that we're supposed to be
* in host mode.
*/
if (!((pdata->operating_mode == FSL_USB2_DR_HOST) ||
(pdata->operating_mode == FSL_USB2_MPH_HOST) ||
(pdata->operating_mode == FSL_USB2_DR_OTG))) {
dev_err(&pdev->dev,
"Non Host Mode configured for %s. Wrong driver linked.\n",
dev_name(&pdev->dev));
return -ENODEV;
}
res = platform_get_resource(pdev, IORESOURCE_IRQ, 0);
if (!res) {
dev_err(&pdev->dev,
"Found HC with no IRQ. Check %s setup!\n",
dev_name(&pdev->dev));
return -ENODEV;
}
irq = res->start;
hcd = usb_create_hcd(driver, &pdev->dev, dev_name(&pdev->dev));
if (!hcd) {
retval = -ENOMEM;
goto err1;
}
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
dev_err(&pdev->dev,
"Found HC with no register addr. Check %s setup!\n",
dev_name(&pdev->dev));
retval = -ENODEV;
goto err2;
}
hcd->rsrc_start = res->start;
hcd->rsrc_len = resource_size(res);
if (!request_mem_region(hcd->rsrc_start, hcd->rsrc_len,
driver->description)) {
dev_dbg(&pdev->dev, "controller already in use\n");
retval = -EBUSY;
goto err2;
}
hcd->regs = ioremap(hcd->rsrc_start, hcd->rsrc_len);
if (hcd->regs == NULL) {
dev_dbg(&pdev->dev, "error mapping memory\n");
retval = -EFAULT;
goto err3;
}
pdata->regs = hcd->regs;
if (pdata->power_budget)
hcd->power_budget = pdata->power_budget;
/*
* do platform specific init: check the clock, grab/config pins, etc.
*/
if (pdata->init && pdata->init(pdev)) {
retval = -ENODEV;
goto err4;
}
/* Enable USB controller, 83xx or 8536 */
if (pdata->have_sysif_regs)
setbits32(hcd->regs + FSL_SOC_USB_CTRL, 0x4);
/* Don't need to set host mode here. It will be done by tdi_reset() */
retval = usb_add_hcd(hcd, irq, IRQF_SHARED);
if (retval != 0)
goto err4;
#ifdef CONFIG_USB_OTG
if (pdata->operating_mode == FSL_USB2_DR_OTG) {
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
hcd->phy = usb_get_phy(USB_PHY_TYPE_USB2);
dev_dbg(&pdev->dev, "hcd=0x%p ehci=0x%p, phy=0x%p\n",
hcd, ehci, hcd->phy);
if (!IS_ERR_OR_NULL(hcd->phy)) {
retval = otg_set_host(hcd->phy->otg,
&ehci_to_hcd(ehci)->self);
if (retval) {
usb_put_phy(hcd->phy);
goto err4;
}
} else {
dev_err(&pdev->dev, "can't find phy\n");
retval = -ENODEV;
goto err4;
}
}
#endif
return retval;
err4:
iounmap(hcd->regs);
err3:
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
err2:
usb_put_hcd(hcd);
err1:
dev_err(&pdev->dev, "init %s fail, %d\n", dev_name(&pdev->dev), retval);
if (pdata->exit)
pdata->exit(pdev);
return retval;
}
/* may be called without controller electrically present */
/* may be called with controller, bus, and devices active */
/**
* usb_hcd_fsl_remove - shutdown processing for FSL-based HCDs
* @dev: USB Host Controller being removed
* Context: !in_interrupt()
*
* Reverses the effect of usb_hcd_fsl_probe().
*
*/
static void usb_hcd_fsl_remove(struct usb_hcd *hcd,
struct platform_device *pdev)
{
struct fsl_usb2_platform_data *pdata = pdev->dev.platform_data;
if (!IS_ERR_OR_NULL(hcd->phy)) {
otg_set_host(hcd->phy->otg, NULL);
usb_put_phy(hcd->phy);
}
usb_remove_hcd(hcd);
/*
* do platform specific un-initialization:
* release iomux pins, disable clock, etc.
*/
if (pdata->exit)
pdata->exit(pdev);
iounmap(hcd->regs);
release_mem_region(hcd->rsrc_start, hcd->rsrc_len);
usb_put_hcd(hcd);
}
static int ehci_fsl_setup_phy(struct usb_hcd *hcd,
enum fsl_usb2_phy_modes phy_mode,
unsigned int port_offset)
{
u32 portsc;
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
void __iomem *non_ehci = hcd->regs;
struct device *dev = hcd->self.controller;
struct fsl_usb2_platform_data *pdata = dev->platform_data;
if (pdata->controller_ver < 0) {
dev_warn(hcd->self.controller, "Could not get controller version\n");
return -ENODEV;
}
portsc = ehci_readl(ehci, &ehci->regs->port_status[port_offset]);
portsc &= ~(PORT_PTS_MSK | PORT_PTS_PTW);
switch (phy_mode) {
case FSL_USB2_PHY_ULPI:
if (pdata->have_sysif_regs && pdata->controller_ver) {
/* controller version 1.6 or above */
setbits32(non_ehci + FSL_SOC_USB_CTRL,
ULPI_PHY_CLK_SEL);
/*
* Due to controller issue of PHY_CLK_VALID in ULPI
* mode, we set USB_CTRL_USB_EN before checking
* PHY_CLK_VALID, otherwise PHY_CLK_VALID doesn't work.
*/
clrsetbits_be32(non_ehci + FSL_SOC_USB_CTRL,
UTMI_PHY_EN, USB_CTRL_USB_EN);
}
portsc |= PORT_PTS_ULPI;
break;
case FSL_USB2_PHY_SERIAL:
portsc |= PORT_PTS_SERIAL;
break;
case FSL_USB2_PHY_UTMI_WIDE:
portsc |= PORT_PTS_PTW;
/* fall through */
case FSL_USB2_PHY_UTMI:
if (pdata->have_sysif_regs && pdata->controller_ver) {
/* controller version 1.6 or above */
setbits32(non_ehci + FSL_SOC_USB_CTRL, UTMI_PHY_EN);
mdelay(FSL_UTMI_PHY_DLY); /* Delay for UTMI PHY CLK to
become stable - 10ms*/
}
/* enable UTMI PHY */
if (pdata->have_sysif_regs)
setbits32(non_ehci + FSL_SOC_USB_CTRL,
CTRL_UTMI_PHY_EN);
portsc |= PORT_PTS_UTMI;
break;
case FSL_USB2_PHY_NONE:
break;
}
if (pdata->have_sysif_regs && pdata->controller_ver &&
(phy_mode == FSL_USB2_PHY_ULPI)) {
/* check PHY_CLK_VALID to get phy clk valid */
if (!spin_event_timeout(in_be32(non_ehci + FSL_SOC_USB_CTRL) &
PHY_CLK_VALID, FSL_USB_PHY_CLK_TIMEOUT, 0)) {
printk(KERN_WARNING "fsl-ehci: USB PHY clock invalid\n");
return -EINVAL;
}
}
ehci_writel(ehci, portsc, &ehci->regs->port_status[port_offset]);
if (phy_mode != FSL_USB2_PHY_ULPI && pdata->have_sysif_regs)
setbits32(non_ehci + FSL_SOC_USB_CTRL, USB_CTRL_USB_EN);
return 0;
}
static int ehci_fsl_usb_setup(struct ehci_hcd *ehci)
{
struct usb_hcd *hcd = ehci_to_hcd(ehci);
struct fsl_usb2_platform_data *pdata;
void __iomem *non_ehci = hcd->regs;
pdata = hcd->self.controller->platform_data;
if (pdata->have_sysif_regs) {
/*
* Turn on cache snooping hardware, since some PowerPC platforms
* wholly rely on hardware to deal with cache coherent
*/
/* Setup Snooping for all the 4GB space */
/* SNOOP1 starts from 0x0, size 2G */
out_be32(non_ehci + FSL_SOC_USB_SNOOP1, 0x0 | SNOOP_SIZE_2GB);
/* SNOOP2 starts from 0x80000000, size 2G */
out_be32(non_ehci + FSL_SOC_USB_SNOOP2, 0x80000000 | SNOOP_SIZE_2GB);
}
if ((pdata->operating_mode == FSL_USB2_DR_HOST) ||
(pdata->operating_mode == FSL_USB2_DR_OTG))
if (ehci_fsl_setup_phy(hcd, pdata->phy_mode, 0))
return -EINVAL;
if (pdata->operating_mode == FSL_USB2_MPH_HOST) {
unsigned int chip, rev, svr;
svr = mfspr(SPRN_SVR);
chip = svr >> 16;
rev = (svr >> 4) & 0xf;
/* Deal with USB Erratum #14 on MPC834x Rev 1.0 & 1.1 chips */
if ((rev == 1) && (chip >= 0x8050) && (chip <= 0x8055))
ehci->has_fsl_port_bug = 1;
if (pdata->port_enables & FSL_USB2_PORT0_ENABLED)
if (ehci_fsl_setup_phy(hcd, pdata->phy_mode, 0))
return -EINVAL;
if (pdata->port_enables & FSL_USB2_PORT1_ENABLED)
if (ehci_fsl_setup_phy(hcd, pdata->phy_mode, 1))
return -EINVAL;
}
if (pdata->have_sysif_regs) {
#ifdef CONFIG_FSL_SOC_BOOKE
out_be32(non_ehci + FSL_SOC_USB_PRICTRL, 0x00000008);
out_be32(non_ehci + FSL_SOC_USB_AGECNTTHRSH, 0x00000080);
#else
out_be32(non_ehci + FSL_SOC_USB_PRICTRL, 0x0000000c);
out_be32(non_ehci + FSL_SOC_USB_AGECNTTHRSH, 0x00000040);
#endif
out_be32(non_ehci + FSL_SOC_USB_SICTRL, 0x00000001);
}
return 0;
}
/* called after powerup, by probe or system-pm "wakeup" */
static int ehci_fsl_reinit(struct ehci_hcd *ehci)
{
if (ehci_fsl_usb_setup(ehci))
return -EINVAL;
return 0;
}
/* called during probe() after chip reset completes */
static int ehci_fsl_setup(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
int retval;
struct fsl_usb2_platform_data *pdata;
struct device *dev;
dev = hcd->self.controller;
pdata = hcd->self.controller->platform_data;
ehci->big_endian_desc = pdata->big_endian_desc;
ehci->big_endian_mmio = pdata->big_endian_mmio;
/* EHCI registers start at offset 0x100 */
ehci->caps = hcd->regs + 0x100;
#ifdef CONFIG_PPC_83xx
/*
* Deal with MPC834X that need port power to be cycled after the power
* fault condition is removed. Otherwise the state machine does not
* reflect PORTSC[CSC] correctly.
*/
ehci->need_oc_pp_cycle = 1;
#endif
hcd->has_tt = 1;
retval = ehci_setup(hcd);
if (retval)
return retval;
if (of_device_is_compatible(dev->parent->of_node,
"fsl,mpc5121-usb2-dr")) {
/*
* set SBUSCFG:AHBBRST so that control msgs don't
* fail when doing heavy PATA writes.
*/
ehci_writel(ehci, SBUSCFG_INCR8,
hcd->regs + FSL_SOC_USB_SBUSCFG);
}
retval = ehci_fsl_reinit(ehci);
return retval;
}
struct ehci_fsl {
struct ehci_hcd ehci;
#ifdef CONFIG_PM
/* Saved USB PHY settings, need to restore after deep sleep. */
u32 usb_ctrl;
#endif
};
#ifdef CONFIG_PM
#ifdef CONFIG_PPC_MPC512x
static int ehci_fsl_mpc512x_drv_suspend(struct device *dev)
{
struct usb_hcd *hcd = dev_get_drvdata(dev);
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct fsl_usb2_platform_data *pdata = dev->platform_data;
u32 tmp;
#ifdef DEBUG
u32 mode = ehci_readl(ehci, hcd->regs + FSL_SOC_USB_USBMODE);
mode &= USBMODE_CM_MASK;
tmp = ehci_readl(ehci, hcd->regs + 0x140); /* usbcmd */
dev_dbg(dev, "suspend=%d already_suspended=%d "
"mode=%d usbcmd %08x\n", pdata->suspended,
pdata->already_suspended, mode, tmp);
#endif
/*
* If the controller is already suspended, then this must be a
* PM suspend. Remember this fact, so that we will leave the
* controller suspended at PM resume time.
*/
if (pdata->suspended) {
dev_dbg(dev, "already suspended, leaving early\n");
pdata->already_suspended = 1;
return 0;
}
dev_dbg(dev, "suspending...\n");
ehci->rh_state = EHCI_RH_SUSPENDED;
dev->power.power_state = PMSG_SUSPEND;
/* ignore non-host interrupts */
clear_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
/* stop the controller */
tmp = ehci_readl(ehci, &ehci->regs->command);
tmp &= ~CMD_RUN;
ehci_writel(ehci, tmp, &ehci->regs->command);
/* save EHCI registers */
pdata->pm_command = ehci_readl(ehci, &ehci->regs->command);
pdata->pm_command &= ~CMD_RUN;
pdata->pm_status = ehci_readl(ehci, &ehci->regs->status);
pdata->pm_intr_enable = ehci_readl(ehci, &ehci->regs->intr_enable);
pdata->pm_frame_index = ehci_readl(ehci, &ehci->regs->frame_index);
pdata->pm_segment = ehci_readl(ehci, &ehci->regs->segment);
pdata->pm_frame_list = ehci_readl(ehci, &ehci->regs->frame_list);
pdata->pm_async_next = ehci_readl(ehci, &ehci->regs->async_next);
pdata->pm_configured_flag =
ehci_readl(ehci, &ehci->regs->configured_flag);
pdata->pm_portsc = ehci_readl(ehci, &ehci->regs->port_status[0]);
pdata->pm_usbgenctrl = ehci_readl(ehci,
hcd->regs + FSL_SOC_USB_USBGENCTRL);
/* clear the W1C bits */
pdata->pm_portsc &= cpu_to_hc32(ehci, ~PORT_RWC_BITS);
pdata->suspended = 1;
/* clear PP to cut power to the port */
tmp = ehci_readl(ehci, &ehci->regs->port_status[0]);
tmp &= ~PORT_POWER;
ehci_writel(ehci, tmp, &ehci->regs->port_status[0]);
return 0;
}
static int ehci_fsl_mpc512x_drv_resume(struct device *dev)
{
struct usb_hcd *hcd = dev_get_drvdata(dev);
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
struct fsl_usb2_platform_data *pdata = dev->platform_data;
u32 tmp;
dev_dbg(dev, "suspend=%d already_suspended=%d\n",
pdata->suspended, pdata->already_suspended);
/*
* If the controller was already suspended at suspend time,
* then don't resume it now.
*/
if (pdata->already_suspended) {
dev_dbg(dev, "already suspended, leaving early\n");
pdata->already_suspended = 0;
return 0;
}
if (!pdata->suspended) {
dev_dbg(dev, "not suspended, leaving early\n");
return 0;
}
pdata->suspended = 0;
dev_dbg(dev, "resuming...\n");
/* set host mode */
tmp = USBMODE_CM_HOST | (pdata->es ? USBMODE_ES : 0);
ehci_writel(ehci, tmp, hcd->regs + FSL_SOC_USB_USBMODE);
ehci_writel(ehci, pdata->pm_usbgenctrl,
hcd->regs + FSL_SOC_USB_USBGENCTRL);
ehci_writel(ehci, ISIPHYCTRL_PXE | ISIPHYCTRL_PHYE,
hcd->regs + FSL_SOC_USB_ISIPHYCTRL);
ehci_writel(ehci, SBUSCFG_INCR8, hcd->regs + FSL_SOC_USB_SBUSCFG);
/* restore EHCI registers */
ehci_writel(ehci, pdata->pm_command, &ehci->regs->command);
ehci_writel(ehci, pdata->pm_intr_enable, &ehci->regs->intr_enable);
ehci_writel(ehci, pdata->pm_frame_index, &ehci->regs->frame_index);
ehci_writel(ehci, pdata->pm_segment, &ehci->regs->segment);
ehci_writel(ehci, pdata->pm_frame_list, &ehci->regs->frame_list);
ehci_writel(ehci, pdata->pm_async_next, &ehci->regs->async_next);
ehci_writel(ehci, pdata->pm_configured_flag,
&ehci->regs->configured_flag);
ehci_writel(ehci, pdata->pm_portsc, &ehci->regs->port_status[0]);
set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
ehci->rh_state = EHCI_RH_RUNNING;
dev->power.power_state = PMSG_ON;
tmp = ehci_readl(ehci, &ehci->regs->command);
tmp |= CMD_RUN;
ehci_writel(ehci, tmp, &ehci->regs->command);
usb_hcd_resume_root_hub(hcd);
return 0;
}
#else
static inline int ehci_fsl_mpc512x_drv_suspend(struct device *dev)
{
return 0;
}
static inline int ehci_fsl_mpc512x_drv_resume(struct device *dev)
{
return 0;
}
#endif /* CONFIG_PPC_MPC512x */
static struct ehci_fsl *hcd_to_ehci_fsl(struct usb_hcd *hcd)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
return container_of(ehci, struct ehci_fsl, ehci);
}
static int ehci_fsl_drv_suspend(struct device *dev)
{
struct usb_hcd *hcd = dev_get_drvdata(dev);
struct ehci_fsl *ehci_fsl = hcd_to_ehci_fsl(hcd);
void __iomem *non_ehci = hcd->regs;
if (of_device_is_compatible(dev->parent->of_node,
"fsl,mpc5121-usb2-dr")) {
return ehci_fsl_mpc512x_drv_suspend(dev);
}
ehci_prepare_ports_for_controller_suspend(hcd_to_ehci(hcd),
device_may_wakeup(dev));
if (!fsl_deep_sleep())
return 0;
ehci_fsl->usb_ctrl = in_be32(non_ehci + FSL_SOC_USB_CTRL);
return 0;
}
static int ehci_fsl_drv_resume(struct device *dev)
{
struct usb_hcd *hcd = dev_get_drvdata(dev);
struct ehci_fsl *ehci_fsl = hcd_to_ehci_fsl(hcd);
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
void __iomem *non_ehci = hcd->regs;
if (of_device_is_compatible(dev->parent->of_node,
"fsl,mpc5121-usb2-dr")) {
return ehci_fsl_mpc512x_drv_resume(dev);
}
ehci_prepare_ports_for_controller_resume(ehci);
if (!fsl_deep_sleep())
return 0;
usb_root_hub_lost_power(hcd->self.root_hub);
/* Restore USB PHY settings and enable the controller. */
out_be32(non_ehci + FSL_SOC_USB_CTRL, ehci_fsl->usb_ctrl);
ehci_reset(ehci);
ehci_fsl_reinit(ehci);
return 0;
}
static int ehci_fsl_drv_restore(struct device *dev)
{
struct usb_hcd *hcd = dev_get_drvdata(dev);
usb_root_hub_lost_power(hcd->self.root_hub);
return 0;
}
static struct dev_pm_ops ehci_fsl_pm_ops = {
.suspend = ehci_fsl_drv_suspend,
.resume = ehci_fsl_drv_resume,
.restore = ehci_fsl_drv_restore,
};
#define EHCI_FSL_PM_OPS (&ehci_fsl_pm_ops)
#else
#define EHCI_FSL_PM_OPS NULL
#endif /* CONFIG_PM */
#ifdef CONFIG_USB_OTG
static int ehci_start_port_reset(struct usb_hcd *hcd, unsigned port)
{
struct ehci_hcd *ehci = hcd_to_ehci(hcd);
u32 status;
if (!port)
return -EINVAL;
port--;
/* start port reset before HNP protocol time out */
status = readl(&ehci->regs->port_status[port]);
if (!(status & PORT_CONNECT))
return -ENODEV;
/* khubd will finish the reset later */
if (ehci_is_TDI(ehci)) {
writel(PORT_RESET |
(status & ~(PORT_CSC | PORT_PEC | PORT_OCC)),
&ehci->regs->port_status[port]);
} else {
writel(PORT_RESET, &ehci->regs->port_status[port]);
}
return 0;
}
#else
#define ehci_start_port_reset NULL
#endif /* CONFIG_USB_OTG */
static const struct hc_driver ehci_fsl_hc_driver = {
.description = hcd_name,
.product_desc = "Freescale On-Chip EHCI Host Controller",
.hcd_priv_size = sizeof(struct ehci_fsl),
/*
* generic hardware linkage
*/
.irq = ehci_irq,
.flags = HCD_USB2 | HCD_MEMORY,
/*
* basic lifecycle operations
*/
.reset = ehci_fsl_setup,
.start = ehci_run,
.stop = ehci_stop,
.shutdown = ehci_shutdown,
/*
* managing i/o requests and associated device resources
*/
.urb_enqueue = ehci_urb_enqueue,
.urb_dequeue = ehci_urb_dequeue,
.endpoint_disable = ehci_endpoint_disable,
.endpoint_reset = ehci_endpoint_reset,
/*
* scheduling support
*/
.get_frame_number = ehci_get_frame,
/*
* root hub support
*/
.hub_status_data = ehci_hub_status_data,
.hub_control = ehci_hub_control,
.bus_suspend = ehci_bus_suspend,
.bus_resume = ehci_bus_resume,
.start_port_reset = ehci_start_port_reset,
.relinquish_port = ehci_relinquish_port,
.port_handed_over = ehci_port_handed_over,
.clear_tt_buffer_complete = ehci_clear_tt_buffer_complete,
};
static int ehci_fsl_drv_probe(struct platform_device *pdev)
{
if (usb_disabled())
return -ENODEV;
/* FIXME we only want one one probe() not two */
return usb_hcd_fsl_probe(&ehci_fsl_hc_driver, pdev);
}
static int ehci_fsl_drv_remove(struct platform_device *pdev)
{
struct usb_hcd *hcd = platform_get_drvdata(pdev);
/* FIXME we only want one one remove() not two */
usb_hcd_fsl_remove(hcd, pdev);
return 0;
}
MODULE_ALIAS("platform:fsl-ehci");
static struct platform_driver ehci_fsl_driver = {
.probe = ehci_fsl_drv_probe,
.remove = ehci_fsl_drv_remove,
.shutdown = usb_hcd_platform_shutdown,
.driver = {
.name = "fsl-ehci",
.pm = EHCI_FSL_PM_OPS,
},
};
View Git Blame Copy Permalink