kevin/linux
1
Fork 0
Code
d2d7c05210
linux/drivers/net/wireless/bcm43xx/bcm43xx.h
Larry Finger aa93c85d09 [PATCH] bcm43xx:Eliminate some 'G Mode Enable' magic numbers 
In code manipulating the TM State Low register of 802.11 cores, two
different magic numbers are used to reference the 'G Mode Enable' bit.
One of these, 0x20000000, is clear, but the other, (0x800 << 18), is not.
This patch replaces both types with a defined constant. In addition, two
bits in the TM State High registers are given definitions to help in
following the code.

Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2007-04-28 11:00:59 -04:00

1014 lines
28 KiB
C
Raw Blame History

#ifndef BCM43xx_H_
#define BCM43xx_H_
#include <linux/hw_random.h>
#include <linux/version.h>
#include <linux/kernel.h>
#include <linux/spinlock.h>
#include <linux/interrupt.h>
#include <linux/stringify.h>
#include <linux/pci.h>
#include <net/ieee80211.h>
#include <net/ieee80211softmac.h>
#include <asm/atomic.h>
#include <asm/io.h>
#include "bcm43xx_debugfs.h"
#include "bcm43xx_leds.h"
#define PFX KBUILD_MODNAME ": "
#define BCM43xx_SWITCH_CORE_MAX_RETRIES 50
#define BCM43xx_IRQWAIT_MAX_RETRIES 100
#define BCM43xx_IO_SIZE 8192
/* Active Core PCI Configuration Register. */
#define BCM43xx_PCICFG_ACTIVE_CORE 0x80
/* SPROM control register. */
#define BCM43xx_PCICFG_SPROMCTL 0x88
/* Interrupt Control PCI Configuration Register. (Only on PCI cores with rev >= 6) */
#define BCM43xx_PCICFG_ICR 0x94
/* MMIO offsets */
#define BCM43xx_MMIO_DMA0_REASON 0x20
#define BCM43xx_MMIO_DMA0_IRQ_MASK 0x24
#define BCM43xx_MMIO_DMA1_REASON 0x28
#define BCM43xx_MMIO_DMA1_IRQ_MASK 0x2C
#define BCM43xx_MMIO_DMA2_REASON 0x30
#define BCM43xx_MMIO_DMA2_IRQ_MASK 0x34
#define BCM43xx_MMIO_DMA3_REASON 0x38
#define BCM43xx_MMIO_DMA3_IRQ_MASK 0x3C
#define BCM43xx_MMIO_DMA4_REASON 0x40
#define BCM43xx_MMIO_DMA4_IRQ_MASK 0x44
#define BCM43xx_MMIO_DMA5_REASON 0x48
#define BCM43xx_MMIO_DMA5_IRQ_MASK 0x4C
#define BCM43xx_MMIO_STATUS_BITFIELD 0x120
#define BCM43xx_MMIO_STATUS2_BITFIELD 0x124
#define BCM43xx_MMIO_GEN_IRQ_REASON 0x128
#define BCM43xx_MMIO_GEN_IRQ_MASK 0x12C
#define BCM43xx_MMIO_RAM_CONTROL 0x130
#define BCM43xx_MMIO_RAM_DATA 0x134
#define BCM43xx_MMIO_PS_STATUS 0x140
#define BCM43xx_MMIO_RADIO_HWENABLED_HI 0x158
#define BCM43xx_MMIO_SHM_CONTROL 0x160
#define BCM43xx_MMIO_SHM_DATA 0x164
#define BCM43xx_MMIO_SHM_DATA_UNALIGNED 0x166
#define BCM43xx_MMIO_XMITSTAT_0 0x170
#define BCM43xx_MMIO_XMITSTAT_1 0x174
#define BCM43xx_MMIO_REV3PLUS_TSF_LOW 0x180 /* core rev >= 3 only */
#define BCM43xx_MMIO_REV3PLUS_TSF_HIGH 0x184 /* core rev >= 3 only */
/* 32-bit DMA */
#define BCM43xx_MMIO_DMA32_BASE0 0x200
#define BCM43xx_MMIO_DMA32_BASE1 0x220
#define BCM43xx_MMIO_DMA32_BASE2 0x240
#define BCM43xx_MMIO_DMA32_BASE3 0x260
#define BCM43xx_MMIO_DMA32_BASE4 0x280
#define BCM43xx_MMIO_DMA32_BASE5 0x2A0
/* 64-bit DMA */
#define BCM43xx_MMIO_DMA64_BASE0 0x200
#define BCM43xx_MMIO_DMA64_BASE1 0x240
#define BCM43xx_MMIO_DMA64_BASE2 0x280
#define BCM43xx_MMIO_DMA64_BASE3 0x2C0
#define BCM43xx_MMIO_DMA64_BASE4 0x300
#define BCM43xx_MMIO_DMA64_BASE5 0x340
/* PIO */
#define BCM43xx_MMIO_PIO1_BASE 0x300
#define BCM43xx_MMIO_PIO2_BASE 0x310
#define BCM43xx_MMIO_PIO3_BASE 0x320
#define BCM43xx_MMIO_PIO4_BASE 0x330
#define BCM43xx_MMIO_PHY_VER 0x3E0
#define BCM43xx_MMIO_PHY_RADIO 0x3E2
#define BCM43xx_MMIO_ANTENNA 0x3E8
#define BCM43xx_MMIO_CHANNEL 0x3F0
#define BCM43xx_MMIO_CHANNEL_EXT 0x3F4
#define BCM43xx_MMIO_RADIO_CONTROL 0x3F6
#define BCM43xx_MMIO_RADIO_DATA_HIGH 0x3F8
#define BCM43xx_MMIO_RADIO_DATA_LOW 0x3FA
#define BCM43xx_MMIO_PHY_CONTROL 0x3FC
#define BCM43xx_MMIO_PHY_DATA 0x3FE
#define BCM43xx_MMIO_MACFILTER_CONTROL 0x420
#define BCM43xx_MMIO_MACFILTER_DATA 0x422
#define BCM43xx_MMIO_RADIO_HWENABLED_LO 0x49A
#define BCM43xx_MMIO_GPIO_CONTROL 0x49C
#define BCM43xx_MMIO_GPIO_MASK 0x49E
#define BCM43xx_MMIO_TSF_0 0x632 /* core rev < 3 only */
#define BCM43xx_MMIO_TSF_1 0x634 /* core rev < 3 only */
#define BCM43xx_MMIO_TSF_2 0x636 /* core rev < 3 only */
#define BCM43xx_MMIO_TSF_3 0x638 /* core rev < 3 only */
#define BCM43xx_MMIO_RNG 0x65A
#define BCM43xx_MMIO_POWERUP_DELAY 0x6A8
/* SPROM offsets. */
#define BCM43xx_SPROM_BASE 0x1000
#define BCM43xx_SPROM_BOARDFLAGS2 0x1c
#define BCM43xx_SPROM_IL0MACADDR 0x24
#define BCM43xx_SPROM_ET0MACADDR 0x27
#define BCM43xx_SPROM_ET1MACADDR 0x2a
#define BCM43xx_SPROM_ETHPHY 0x2d
#define BCM43xx_SPROM_BOARDREV 0x2e
#define BCM43xx_SPROM_PA0B0 0x2f
#define BCM43xx_SPROM_PA0B1 0x30
#define BCM43xx_SPROM_PA0B2 0x31
#define BCM43xx_SPROM_WL0GPIO0 0x32
#define BCM43xx_SPROM_WL0GPIO2 0x33
#define BCM43xx_SPROM_MAXPWR 0x34
#define BCM43xx_SPROM_PA1B0 0x35
#define BCM43xx_SPROM_PA1B1 0x36
#define BCM43xx_SPROM_PA1B2 0x37
#define BCM43xx_SPROM_IDL_TSSI_TGT 0x38
#define BCM43xx_SPROM_BOARDFLAGS 0x39
#define BCM43xx_SPROM_ANTENNA_GAIN 0x3a
#define BCM43xx_SPROM_VERSION 0x3f
/* BCM43xx_SPROM_BOARDFLAGS values */
#define BCM43xx_BFL_BTCOEXIST 0x0001 /* implements Bluetooth coexistance */
#define BCM43xx_BFL_PACTRL 0x0002 /* GPIO 9 controlling the PA */
#define BCM43xx_BFL_AIRLINEMODE 0x0004 /* implements GPIO 13 radio disable indication */
#define BCM43xx_BFL_RSSI 0x0008 /* software calculates nrssi slope. */
#define BCM43xx_BFL_ENETSPI 0x0010 /* has ephy roboswitch spi */
#define BCM43xx_BFL_XTAL_NOSLOW 0x0020 /* no slow clock available */
#define BCM43xx_BFL_CCKHIPWR 0x0040 /* can do high power CCK transmission */
#define BCM43xx_BFL_ENETADM 0x0080 /* has ADMtek switch */
#define BCM43xx_BFL_ENETVLAN 0x0100 /* can do vlan */
#define BCM43xx_BFL_AFTERBURNER 0x0200 /* supports Afterburner mode */
#define BCM43xx_BFL_NOPCI 0x0400 /* leaves PCI floating */
#define BCM43xx_BFL_FEM 0x0800 /* supports the Front End Module */
#define BCM43xx_BFL_EXTLNA 0x1000 /* has an external LNA */
#define BCM43xx_BFL_HGPA 0x2000 /* had high gain PA */
#define BCM43xx_BFL_BTCMOD 0x4000 /* BFL_BTCOEXIST is given in alternate GPIOs */
#define BCM43xx_BFL_ALTIQ 0x8000 /* alternate I/Q settings */
/* GPIO register offset, in both ChipCommon and PCI core. */
#define BCM43xx_GPIO_CONTROL 0x6c
/* SHM Routing */
#define BCM43xx_SHM_SHARED 0x0001
#define BCM43xx_SHM_WIRELESS 0x0002
#define BCM43xx_SHM_PCM 0x0003
#define BCM43xx_SHM_HWMAC 0x0004
#define BCM43xx_SHM_UCODE 0x0300
/* MacFilter offsets. */
#define BCM43xx_MACFILTER_SELF 0x0000
#define BCM43xx_MACFILTER_ASSOC 0x0003
/* Chipcommon registers. */
#define BCM43xx_CHIPCOMMON_CAPABILITIES 0x04
#define BCM43xx_CHIPCOMMON_CTL 0x28
#define BCM43xx_CHIPCOMMON_PLLONDELAY 0xB0
#define BCM43xx_CHIPCOMMON_FREFSELDELAY 0xB4
#define BCM43xx_CHIPCOMMON_SLOWCLKCTL 0xB8
#define BCM43xx_CHIPCOMMON_SYSCLKCTL 0xC0
/* PCI core specific registers. */
#define BCM43xx_PCICORE_BCAST_ADDR 0x50
#define BCM43xx_PCICORE_BCAST_DATA 0x54
#define BCM43xx_PCICORE_SBTOPCI2 0x108
/* SBTOPCI2 values. */
#define BCM43xx_SBTOPCI2_PREFETCH 0x4
#define BCM43xx_SBTOPCI2_BURST 0x8
#define BCM43xx_SBTOPCI2_MEMREAD_MULTI 0x20
/* PCI-E core registers. */
#define BCM43xx_PCIECORE_REG_ADDR 0x0130
#define BCM43xx_PCIECORE_REG_DATA 0x0134
#define BCM43xx_PCIECORE_MDIO_CTL 0x0128
#define BCM43xx_PCIECORE_MDIO_DATA 0x012C
/* PCI-E registers. */
#define BCM43xx_PCIE_TLP_WORKAROUND 0x0004
#define BCM43xx_PCIE_DLLP_LINKCTL 0x0100
/* PCI-E MDIO bits. */
#define BCM43xx_PCIE_MDIO_ST 0x40000000
#define BCM43xx_PCIE_MDIO_WT 0x10000000
#define BCM43xx_PCIE_MDIO_DEV 22
#define BCM43xx_PCIE_MDIO_REG 18
#define BCM43xx_PCIE_MDIO_TA 0x00020000
#define BCM43xx_PCIE_MDIO_TC 0x0100
/* MDIO devices. */
#define BCM43xx_MDIO_SERDES_RX 0x1F
/* SERDES RX registers. */
#define BCM43xx_SERDES_RXTIMER 0x2
#define BCM43xx_SERDES_CDR 0x6
#define BCM43xx_SERDES_CDR_BW 0x7
/* Chipcommon capabilities. */
#define BCM43xx_CAPABILITIES_PCTL 0x00040000
#define BCM43xx_CAPABILITIES_PLLMASK 0x00030000
#define BCM43xx_CAPABILITIES_PLLSHIFT 16
#define BCM43xx_CAPABILITIES_FLASHMASK 0x00000700
#define BCM43xx_CAPABILITIES_FLASHSHIFT 8
#define BCM43xx_CAPABILITIES_EXTBUSPRESENT 0x00000040
#define BCM43xx_CAPABILITIES_UARTGPIO 0x00000020
#define BCM43xx_CAPABILITIES_UARTCLOCKMASK 0x00000018
#define BCM43xx_CAPABILITIES_UARTCLOCKSHIFT 3
#define BCM43xx_CAPABILITIES_MIPSBIGENDIAN 0x00000004
#define BCM43xx_CAPABILITIES_NRUARTSMASK 0x00000003
/* PowerControl */
#define BCM43xx_PCTL_IN 0xB0
#define BCM43xx_PCTL_OUT 0xB4
#define BCM43xx_PCTL_OUTENABLE 0xB8
#define BCM43xx_PCTL_XTAL_POWERUP 0x40
#define BCM43xx_PCTL_PLL_POWERDOWN 0x80
/* PowerControl Clock Modes */
#define BCM43xx_PCTL_CLK_FAST 0x00
#define BCM43xx_PCTL_CLK_SLOW 0x01
#define BCM43xx_PCTL_CLK_DYNAMIC 0x02
#define BCM43xx_PCTL_FORCE_SLOW 0x0800
#define BCM43xx_PCTL_FORCE_PLL 0x1000
#define BCM43xx_PCTL_DYN_XTAL 0x2000
/* COREIDs */
#define BCM43xx_COREID_CHIPCOMMON 0x800
#define BCM43xx_COREID_ILINE20 0x801
#define BCM43xx_COREID_SDRAM 0x803
#define BCM43xx_COREID_PCI 0x804
#define BCM43xx_COREID_MIPS 0x805
#define BCM43xx_COREID_ETHERNET 0x806
#define BCM43xx_COREID_V90 0x807
#define BCM43xx_COREID_USB11_HOSTDEV 0x80a
#define BCM43xx_COREID_IPSEC 0x80b
#define BCM43xx_COREID_PCMCIA 0x80d
#define BCM43xx_COREID_EXT_IF 0x80f
#define BCM43xx_COREID_80211 0x812
#define BCM43xx_COREID_MIPS_3302 0x816
#define BCM43xx_COREID_USB11_HOST 0x817
#define BCM43xx_COREID_USB11_DEV 0x818
#define BCM43xx_COREID_USB20_HOST 0x819
#define BCM43xx_COREID_USB20_DEV 0x81a
#define BCM43xx_COREID_SDIO_HOST 0x81b
#define BCM43xx_COREID_PCIE 0x820
/* Core Information Registers */
#define BCM43xx_CIR_BASE 0xf00
#define BCM43xx_CIR_SBTPSFLAG (BCM43xx_CIR_BASE + 0x18)
#define BCM43xx_CIR_SBIMSTATE (BCM43xx_CIR_BASE + 0x90)
#define BCM43xx_CIR_SBINTVEC (BCM43xx_CIR_BASE + 0x94)
#define BCM43xx_CIR_SBTMSTATELOW (BCM43xx_CIR_BASE + 0x98)
#define BCM43xx_CIR_SBTMSTATEHIGH (BCM43xx_CIR_BASE + 0x9c)
#define BCM43xx_CIR_SBIMCONFIGLOW (BCM43xx_CIR_BASE + 0xa8)
#define BCM43xx_CIR_SB_ID_HI (BCM43xx_CIR_BASE + 0xfc)
/* Mask to get the Backplane Flag Number from SBTPSFLAG. */
#define BCM43xx_BACKPLANE_FLAG_NR_MASK 0x3f
/* SBIMCONFIGLOW values/masks. */
#define BCM43xx_SBIMCONFIGLOW_SERVICE_TOUT_MASK 0x00000007
#define BCM43xx_SBIMCONFIGLOW_SERVICE_TOUT_SHIFT 0
#define BCM43xx_SBIMCONFIGLOW_REQUEST_TOUT_MASK 0x00000070
#define BCM43xx_SBIMCONFIGLOW_REQUEST_TOUT_SHIFT 4
#define BCM43xx_SBIMCONFIGLOW_CONNID_MASK 0x00ff0000
#define BCM43xx_SBIMCONFIGLOW_CONNID_SHIFT 16
/* sbtmstatelow state flags */
#define BCM43xx_SBTMSTATELOW_RESET 0x01
#define BCM43xx_SBTMSTATELOW_REJECT 0x02
#define BCM43xx_SBTMSTATELOW_CLOCK 0x10000
#define BCM43xx_SBTMSTATELOW_FORCE_GATE_CLOCK 0x20000
#define BCM43xx_SBTMSTATELOW_G_MODE_ENABLE 0x20000000
/* sbtmstatehigh state flags */
#define BCM43xx_SBTMSTATEHIGH_SERROR 0x00000001
#define BCM43xx_SBTMSTATEHIGH_BUSY 0x00000004
#define BCM43xx_SBTMSTATEHIGH_TIMEOUT 0x00000020
#define BCM43xx_SBTMSTATEHIGH_G_PHY_AVAIL 0x00010000
#define BCM43xx_SBTMSTATEHIGH_A_PHY_AVAIL 0x00020000
#define BCM43xx_SBTMSTATEHIGH_COREFLAGS 0x1FFF0000
#define BCM43xx_SBTMSTATEHIGH_DMA64BIT 0x10000000
#define BCM43xx_SBTMSTATEHIGH_GATEDCLK 0x20000000
#define BCM43xx_SBTMSTATEHIGH_BISTFAILED 0x40000000
#define BCM43xx_SBTMSTATEHIGH_BISTCOMPLETE 0x80000000
/* sbimstate flags */
#define BCM43xx_SBIMSTATE_IB_ERROR 0x20000
#define BCM43xx_SBIMSTATE_TIMEOUT 0x40000
/* PHYVersioning */
#define BCM43xx_PHYTYPE_A 0x00
#define BCM43xx_PHYTYPE_B 0x01
#define BCM43xx_PHYTYPE_G 0x02
/* PHYRegisters */
#define BCM43xx_PHY_ILT_A_CTRL 0x0072
#define BCM43xx_PHY_ILT_A_DATA1 0x0073
#define BCM43xx_PHY_ILT_A_DATA2 0x0074
#define BCM43xx_PHY_G_LO_CONTROL 0x0810
#define BCM43xx_PHY_ILT_G_CTRL 0x0472
#define BCM43xx_PHY_ILT_G_DATA1 0x0473
#define BCM43xx_PHY_ILT_G_DATA2 0x0474
#define BCM43xx_PHY_A_PCTL 0x007B
#define BCM43xx_PHY_G_PCTL 0x0029
#define BCM43xx_PHY_A_CRS 0x0029
#define BCM43xx_PHY_RADIO_BITFIELD 0x0401
#define BCM43xx_PHY_G_CRS 0x0429
#define BCM43xx_PHY_NRSSILT_CTRL 0x0803
#define BCM43xx_PHY_NRSSILT_DATA 0x0804
/* RadioRegisters */
#define BCM43xx_RADIOCTL_ID 0x01
/* StatusBitField */
#define BCM43xx_SBF_MAC_ENABLED 0x00000001
#define BCM43xx_SBF_2 0x00000002 /*FIXME: fix name*/
#define BCM43xx_SBF_CORE_READY 0x00000004
#define BCM43xx_SBF_400 0x00000400 /*FIXME: fix name*/
#define BCM43xx_SBF_4000 0x00004000 /*FIXME: fix name*/
#define BCM43xx_SBF_8000 0x00008000 /*FIXME: fix name*/
#define BCM43xx_SBF_XFER_REG_BYTESWAP 0x00010000
#define BCM43xx_SBF_MODE_NOTADHOC 0x00020000
#define BCM43xx_SBF_MODE_AP 0x00040000
#define BCM43xx_SBF_RADIOREG_LOCK 0x00080000
#define BCM43xx_SBF_MODE_MONITOR 0x00400000
#define BCM43xx_SBF_MODE_PROMISC 0x01000000
#define BCM43xx_SBF_PS1 0x02000000
#define BCM43xx_SBF_PS2 0x04000000
#define BCM43xx_SBF_NO_SSID_BCAST 0x08000000
#define BCM43xx_SBF_TIME_UPDATE 0x10000000
#define BCM43xx_SBF_MODE_G 0x80000000
/* Microcode */
#define BCM43xx_UCODE_REVISION 0x0000
#define BCM43xx_UCODE_PATCHLEVEL 0x0002
#define BCM43xx_UCODE_DATE 0x0004
#define BCM43xx_UCODE_TIME 0x0006
#define BCM43xx_UCODE_STATUS 0x0040
/* MicrocodeFlagsBitfield (addr + lo-word values?)*/
#define BCM43xx_UCODEFLAGS_OFFSET 0x005E
#define BCM43xx_UCODEFLAG_AUTODIV 0x0001
#define BCM43xx_UCODEFLAG_UNKBGPHY 0x0002
#define BCM43xx_UCODEFLAG_UNKBPHY 0x0004
#define BCM43xx_UCODEFLAG_UNKGPHY 0x0020
#define BCM43xx_UCODEFLAG_UNKPACTRL 0x0040
#define BCM43xx_UCODEFLAG_JAPAN 0x0080
/* Hardware Radio Enable masks */
#define BCM43xx_MMIO_RADIO_HWENABLED_HI_MASK (1 << 16)
#define BCM43xx_MMIO_RADIO_HWENABLED_LO_MASK (1 << 4)
/* Generic-Interrupt reasons. */
#define BCM43xx_IRQ_READY (1 << 0)
#define BCM43xx_IRQ_BEACON (1 << 1)
#define BCM43xx_IRQ_PS (1 << 2)
#define BCM43xx_IRQ_REG124 (1 << 5)
#define BCM43xx_IRQ_PMQ (1 << 6)
#define BCM43xx_IRQ_PIO_WORKAROUND (1 << 8)
#define BCM43xx_IRQ_XMIT_ERROR (1 << 11)
#define BCM43xx_IRQ_RX (1 << 15)
#define BCM43xx_IRQ_SCAN (1 << 16)
#define BCM43xx_IRQ_NOISE (1 << 18)
#define BCM43xx_IRQ_XMIT_STATUS (1 << 29)
#define BCM43xx_IRQ_ALL 0xffffffff
#define BCM43xx_IRQ_INITIAL (BCM43xx_IRQ_PS | \
BCM43xx_IRQ_REG124 | \
BCM43xx_IRQ_PMQ | \
BCM43xx_IRQ_XMIT_ERROR | \
BCM43xx_IRQ_RX | \
BCM43xx_IRQ_SCAN | \
BCM43xx_IRQ_NOISE | \
BCM43xx_IRQ_XMIT_STATUS)
/* Initial default iw_mode */
#define BCM43xx_INITIAL_IWMODE IW_MODE_INFRA
/* Bus type PCI. */
#define BCM43xx_BUSTYPE_PCI 0
/* Bus type Silicone Backplane Bus. */
#define BCM43xx_BUSTYPE_SB 1
/* Bus type PCMCIA. */
#define BCM43xx_BUSTYPE_PCMCIA 2
/* Threshold values. */
#define BCM43xx_MIN_RTS_THRESHOLD 1U
#define BCM43xx_MAX_RTS_THRESHOLD 2304U
#define BCM43xx_DEFAULT_RTS_THRESHOLD BCM43xx_MAX_RTS_THRESHOLD
#define BCM43xx_DEFAULT_SHORT_RETRY_LIMIT 7
#define BCM43xx_DEFAULT_LONG_RETRY_LIMIT 4
/* FIXME: the next line is a guess as to what the maximum RSSI value might be */
#define RX_RSSI_MAX 60
/* Max size of a security key */
#define BCM43xx_SEC_KEYSIZE 16
/* Security algorithms. */
enum {
BCM43xx_SEC_ALGO_NONE = 0, /* unencrypted, as of TX header. */
BCM43xx_SEC_ALGO_WEP,
BCM43xx_SEC_ALGO_UNKNOWN,
BCM43xx_SEC_ALGO_AES,
BCM43xx_SEC_ALGO_WEP104,
BCM43xx_SEC_ALGO_TKIP,
};
#ifdef assert
# undef assert
#endif
#ifdef CONFIG_BCM43XX_DEBUG
#define assert(expr) \
do { \
if (unlikely(!(expr))) { \
printk(KERN_ERR PFX "ASSERTION FAILED (%s) at: %s:%d:%s()\n", \
#expr, __FILE__, __LINE__, __FUNCTION__); \
} \
} while (0)
#else
#define assert(expr) do { /* nothing */ } while (0)
#endif
/* rate limited printk(). */
#ifdef printkl
# undef printkl
#endif
#define printkl(f, x...) do { if (printk_ratelimit()) printk(f ,##x); } while (0)
/* rate limited printk() for debugging */
#ifdef dprintkl
# undef dprintkl
#endif
#ifdef CONFIG_BCM43XX_DEBUG
# define dprintkl printkl
#else
# define dprintkl(f, x...) do { /* nothing */ } while (0)
#endif
/* Helper macro for if branches.
* An if branch marked with this macro is only taken in DEBUG mode.
* Example:
* if (DEBUG_ONLY(foo == bar)) {
* do something
* }
* In DEBUG mode, the branch will be taken if (foo == bar).
* In non-DEBUG mode, the branch will never be taken.
*/
#ifdef DEBUG_ONLY
# undef DEBUG_ONLY
#endif
#ifdef CONFIG_BCM43XX_DEBUG
# define DEBUG_ONLY(x) (x)
#else
# define DEBUG_ONLY(x) 0
#endif
/* debugging printk() */
#ifdef dprintk
# undef dprintk
#endif
#ifdef CONFIG_BCM43XX_DEBUG
# define dprintk(f, x...) do { printk(f ,##x); } while (0)
#else
# define dprintk(f, x...) do { /* nothing */ } while (0)
#endif
struct net_device;
struct pci_dev;
struct bcm43xx_dmaring;
struct bcm43xx_pioqueue;
struct bcm43xx_initval {
u16 offset;
u16 size;
u32 value;
} __attribute__((__packed__));
/* Values for bcm430x_sprominfo.locale */
enum {
BCM43xx_LOCALE_WORLD = 0,
BCM43xx_LOCALE_THAILAND,
BCM43xx_LOCALE_ISRAEL,
BCM43xx_LOCALE_JORDAN,
BCM43xx_LOCALE_CHINA,
BCM43xx_LOCALE_JAPAN,
BCM43xx_LOCALE_USA_CANADA_ANZ,
BCM43xx_LOCALE_EUROPE,
BCM43xx_LOCALE_USA_LOW,
BCM43xx_LOCALE_JAPAN_HIGH,
BCM43xx_LOCALE_ALL,
BCM43xx_LOCALE_NONE,
};
#define BCM43xx_SPROM_SIZE 64 /* in 16-bit words. */
struct bcm43xx_sprominfo {
u16 boardflags2;
u8 il0macaddr[6];
u8 et0macaddr[6];
u8 et1macaddr[6];
u8 et0phyaddr:5;
u8 et1phyaddr:5;
u8 boardrev;
u8 locale:4;
u8 antennas_aphy:2;
u8 antennas_bgphy:2;
u16 pa0b0;
u16 pa0b1;
u16 pa0b2;
u8 wl0gpio0;
u8 wl0gpio1;
u8 wl0gpio2;
u8 wl0gpio3;
u8 maxpower_aphy;
u8 maxpower_bgphy;
u16 pa1b0;
u16 pa1b1;
u16 pa1b2;
u8 idle_tssi_tgt_aphy;
u8 idle_tssi_tgt_bgphy;
u16 boardflags;
u16 antennagain_aphy;
u16 antennagain_bgphy;
};
/* Value pair to measure the LocalOscillator. */
struct bcm43xx_lopair {
s8 low;
s8 high;
u8 used:1;
};
#define BCM43xx_LO_COUNT (14*4)
struct bcm43xx_phyinfo {
/* Hardware Data */
u8 analog;
u8 type;
u8 rev;
u16 antenna_diversity;
u16 savedpctlreg;
u16 minlowsig[2];
u16 minlowsigpos[2];
u8 connected:1,
calibrated:1,
is_locked:1, /* used in bcm43xx_phy_{un}lock() */
dyn_tssi_tbl:1; /* used in bcm43xx_phy_init_tssi2dbm_table() */
/* LO Measurement Data.
* Use bcm43xx_get_lopair() to get a value.
*/
struct bcm43xx_lopair *_lo_pairs;
/* TSSI to dBm table in use */
const s8 *tssi2dbm;
/* idle TSSI value */
s8 idle_tssi;
/* Values from bcm43xx_calc_loopback_gain() */
u16 loopback_gain[2];
/* PHY lock for core.rev < 3
* This lock is only used by bcm43xx_phy_{un}lock()
*/
spinlock_t lock;
/* Firmware. */
const struct firmware *ucode;
const struct firmware *pcm;
const struct firmware *initvals0;
const struct firmware *initvals1;
};
struct bcm43xx_radioinfo {
u16 manufact;
u16 version;
u8 revision;
/* Desired TX power in dBm Q5.2 */
u16 txpower_desired;
/* TX Power control values. */
union {
/* B/G PHY */
struct {
u16 baseband_atten;
u16 radio_atten;
u16 txctl1;
u16 txctl2;
};
/* A PHY */
struct {
u16 txpwr_offset;
};
};
/* Current Interference Mitigation mode */
int interfmode;
/* Stack of saved values from the Interference Mitigation code.
* Each value in the stack is layed out as follows:
* bit 0-11: offset
* bit 12-15: register ID
* bit 16-32: value
* register ID is: 0x1 PHY, 0x2 Radio, 0x3 ILT
*/
#define BCM43xx_INTERFSTACK_SIZE 26
u32 interfstack[BCM43xx_INTERFSTACK_SIZE];
/* Saved values from the NRSSI Slope calculation */
s16 nrssi[2];
s32 nrssislope;
/* In memory nrssi lookup table. */
s8 nrssi_lt[64];
/* current channel */
u8 channel;
u8 initial_channel;
u16 lofcal;
u16 initval;
u8 enabled:1;
/* ACI (adjacent channel interference) flags. */
u8 aci_enable:1,
aci_wlan_automatic:1,
aci_hw_rssi:1;
};
/* Data structures for DMA transmission, per 80211 core. */
struct bcm43xx_dma {
struct bcm43xx_dmaring *tx_ring0;
struct bcm43xx_dmaring *tx_ring1;
struct bcm43xx_dmaring *tx_ring2;
struct bcm43xx_dmaring *tx_ring3;
struct bcm43xx_dmaring *tx_ring4;
struct bcm43xx_dmaring *tx_ring5;
struct bcm43xx_dmaring *rx_ring0;
struct bcm43xx_dmaring *rx_ring3; /* only available on core.rev < 5 */
};
/* Data structures for PIO transmission, per 80211 core. */
struct bcm43xx_pio {
struct bcm43xx_pioqueue *queue0;
struct bcm43xx_pioqueue *queue1;
struct bcm43xx_pioqueue *queue2;
struct bcm43xx_pioqueue *queue3;
};
#define BCM43xx_MAX_80211_CORES 2
#ifdef CONFIG_BCM947XX
#define core_offset(bcm) (bcm)->current_core_offset
#else
#define core_offset(bcm) 0
#endif
/* Generic information about a core. */
struct bcm43xx_coreinfo {
u8 available:1,
enabled:1,
initialized:1;
/** core_rev revision number */
u8 rev;
/** Index number for _switch_core() */
u8 index;
/** core_id ID number */
u16 id;
/** Core-specific data. */
void *priv;
};
/* Additional information for each 80211 core. */
struct bcm43xx_coreinfo_80211 {
/* PHY device. */
struct bcm43xx_phyinfo phy;
/* Radio device. */
struct bcm43xx_radioinfo radio;
union {
/* DMA context. */
struct bcm43xx_dma dma;
/* PIO context. */
struct bcm43xx_pio pio;
};
};
/* Context information for a noise calculation (Link Quality). */
struct bcm43xx_noise_calculation {
struct bcm43xx_coreinfo *core_at_start;
u8 channel_at_start;
u8 calculation_running:1;
u8 nr_samples;
s8 samples[8][4];
};
struct bcm43xx_stats {
u8 noise;
struct iw_statistics wstats;
/* Store the last TX/RX times here for updating the leds. */
unsigned long last_tx;
unsigned long last_rx;
};
struct bcm43xx_key {
u8 enabled:1;
u8 algorithm;
};
/* Driver initialization status. */
enum {
BCM43xx_STAT_UNINIT, /* Uninitialized. */
BCM43xx_STAT_INITIALIZING, /* init_board() in progress. */
BCM43xx_STAT_INITIALIZED, /* Fully operational. */
BCM43xx_STAT_SHUTTINGDOWN, /* free_board() in progress. */
BCM43xx_STAT_RESTARTING, /* controller_restart() called. */
};
#define bcm43xx_status(bcm) atomic_read(&(bcm)->init_status)
#define bcm43xx_set_status(bcm, stat) do { \
atomic_set(&(bcm)->init_status, (stat)); \
smp_wmb(); \
} while (0)
/* *** THEORY OF LOCKING ***
*
* We have two different locks in the bcm43xx driver.
* => bcm->mutex: General sleeping mutex. Protects struct bcm43xx_private
* and the device registers. This mutex does _not_ protect
* against concurrency from the IRQ handler.
* => bcm->irq_lock: IRQ spinlock. Protects against IRQ handler concurrency.
*
* Please note that, if you only take the irq_lock, you are not protected
* against concurrency from the periodic work handlers.
* Most times you want to take _both_ locks.
*/
struct bcm43xx_private {
struct ieee80211_device *ieee;
struct ieee80211softmac_device *softmac;
struct net_device *net_dev;
struct pci_dev *pci_dev;
unsigned int irq;
void __iomem *mmio_addr;
spinlock_t irq_lock;
struct mutex mutex;
/* Driver initialization status BCM43xx_STAT_*** */
atomic_t init_status;
u16 was_initialized:1, /* for PCI suspend/resume. */
__using_pio:1, /* Internal, use bcm43xx_using_pio(). */
bad_frames_preempt:1, /* Use "Bad Frames Preemption" (default off) */
reg124_set_0x4:1, /* Some variable to keep track of IRQ stuff. */
short_preamble:1, /* TRUE, if short preamble is enabled. */
firmware_norelease:1, /* Do not release the firmware. Used on suspend. */
radio_hw_enable:1; /* TRUE if radio is hardware enabled */
struct bcm43xx_stats stats;
/* Bus type we are connected to.
* This is currently always BCM43xx_BUSTYPE_PCI
*/
u8 bustype;
u64 dma_mask;
u16 board_vendor;
u16 board_type;
u16 board_revision;
u16 chip_id;
u8 chip_rev;
u8 chip_package;
struct bcm43xx_sprominfo sprom;
#define BCM43xx_NR_LEDS 4
struct bcm43xx_led leds[BCM43xx_NR_LEDS];
spinlock_t leds_lock;
/* The currently active core. */
struct bcm43xx_coreinfo *current_core;
#ifdef CONFIG_BCM947XX
/** current core memory offset */
u32 current_core_offset;
#endif
struct bcm43xx_coreinfo *active_80211_core;
/* coreinfo structs for all possible cores follow.
* Note that a core might not exist.
* So check the coreinfo flags before using it.
*/
struct bcm43xx_coreinfo core_chipcommon;
struct bcm43xx_coreinfo core_pci;
struct bcm43xx_coreinfo core_80211[ BCM43xx_MAX_80211_CORES ];
/* Additional information, specific to the 80211 cores. */
struct bcm43xx_coreinfo_80211 core_80211_ext[ BCM43xx_MAX_80211_CORES ];
/* Number of available 80211 cores. */
int nr_80211_available;
u32 chipcommon_capabilities;
/* Reason code of the last interrupt. */
u32 irq_reason;
u32 dma_reason[6];
/* saved irq enable/disable state bitfield. */
u32 irq_savedstate;
/* Link Quality calculation context. */
struct bcm43xx_noise_calculation noisecalc;
/* if > 0 MAC is suspended. if == 0 MAC is enabled. */
int mac_suspended;
/* Threshold values. */
//TODO: The RTS thr has to be _used_. Currently, it is only set via WX.
u32 rts_threshold;
/* Interrupt Service Routine tasklet (bottom-half) */
struct tasklet_struct isr_tasklet;
/* Periodic tasks */
struct delayed_work periodic_work;
unsigned int periodic_state;
struct work_struct restart_work;
/* Informational stuff. */
char nick[IW_ESSID_MAX_SIZE + 1];
/* encryption/decryption */
u16 security_offset;
struct bcm43xx_key key[54];
u8 default_key_idx;
/* Random Number Generator. */
struct hwrng rng;
char rng_name[20 + 1];
/* Debugging stuff follows. */
#ifdef CONFIG_BCM43XX_DEBUG
struct bcm43xx_dfsentry *dfsentry;
#endif
};
static inline
struct bcm43xx_private * bcm43xx_priv(struct net_device *dev)
{
return ieee80211softmac_priv(dev);
}
struct device;
static inline
struct bcm43xx_private * dev_to_bcm(struct device *dev)
{
struct net_device *net_dev;
struct bcm43xx_private *bcm;
net_dev = dev_get_drvdata(dev);
bcm = bcm43xx_priv(net_dev);
return bcm;
}
/* Helper function, which returns a boolean.
* TRUE, if PIO is used; FALSE, if DMA is used.
*/
#if defined(CONFIG_BCM43XX_DMA) && defined(CONFIG_BCM43XX_PIO)
static inline
int bcm43xx_using_pio(struct bcm43xx_private *bcm)
{
return bcm->__using_pio;
}
#elif defined(CONFIG_BCM43XX_DMA)
static inline
int bcm43xx_using_pio(struct bcm43xx_private *bcm)
{
return 0;
}
#elif defined(CONFIG_BCM43XX_PIO)
static inline
int bcm43xx_using_pio(struct bcm43xx_private *bcm)
{
return 1;
}
#else
# error "Using neither DMA nor PIO? Confused..."
#endif
/* Helper functions to access data structures private to the 80211 cores.
* Note that we _must_ have an 80211 core mapped when calling
* any of these functions.
*/
static inline
struct bcm43xx_coreinfo_80211 *
bcm43xx_current_80211_priv(struct bcm43xx_private *bcm)
{
assert(bcm->current_core->id == BCM43xx_COREID_80211);
return bcm->current_core->priv;
}
static inline
struct bcm43xx_pio * bcm43xx_current_pio(struct bcm43xx_private *bcm)
{
assert(bcm43xx_using_pio(bcm));
return &(bcm43xx_current_80211_priv(bcm)->pio);
}
static inline
struct bcm43xx_dma * bcm43xx_current_dma(struct bcm43xx_private *bcm)
{
assert(!bcm43xx_using_pio(bcm));
return &(bcm43xx_current_80211_priv(bcm)->dma);
}
static inline
struct bcm43xx_phyinfo * bcm43xx_current_phy(struct bcm43xx_private *bcm)
{
return &(bcm43xx_current_80211_priv(bcm)->phy);
}
static inline
struct bcm43xx_radioinfo * bcm43xx_current_radio(struct bcm43xx_private *bcm)
{
return &(bcm43xx_current_80211_priv(bcm)->radio);
}
static inline
struct bcm43xx_lopair * bcm43xx_get_lopair(struct bcm43xx_phyinfo *phy,
u16 radio_attenuation,
u16 baseband_attenuation)
{
return phy->_lo_pairs + (radio_attenuation + 14 * (baseband_attenuation / 2));
}
static inline
u16 bcm43xx_read16(struct bcm43xx_private *bcm, u16 offset)
{
return ioread16(bcm->mmio_addr + core_offset(bcm) + offset);
}
static inline
void bcm43xx_write16(struct bcm43xx_private *bcm, u16 offset, u16 value)
{
iowrite16(value, bcm->mmio_addr + core_offset(bcm) + offset);
}
static inline
u32 bcm43xx_read32(struct bcm43xx_private *bcm, u16 offset)
{
return ioread32(bcm->mmio_addr + core_offset(bcm) + offset);
}
static inline
void bcm43xx_write32(struct bcm43xx_private *bcm, u16 offset, u32 value)
{
iowrite32(value, bcm->mmio_addr + core_offset(bcm) + offset);
}
static inline
int bcm43xx_pci_read_config16(struct bcm43xx_private *bcm, int offset, u16 *value)
{
return pci_read_config_word(bcm->pci_dev, offset, value);
}
static inline
int bcm43xx_pci_read_config32(struct bcm43xx_private *bcm, int offset, u32 *value)
{
return pci_read_config_dword(bcm->pci_dev, offset, value);
}
static inline
int bcm43xx_pci_write_config16(struct bcm43xx_private *bcm, int offset, u16 value)
{
return pci_write_config_word(bcm->pci_dev, offset, value);
}
static inline
int bcm43xx_pci_write_config32(struct bcm43xx_private *bcm, int offset, u32 value)
{
return pci_write_config_dword(bcm->pci_dev, offset, value);
}
/** Limit a value between two limits */
#ifdef limit_value
# undef limit_value
#endif
#define limit_value(value, min, max) \
({ \
typeof(value) __value = (value); \
typeof(value) __min = (min); \
typeof(value) __max = (max); \
if (__value < __min) \
__value = __min; \
else if (__value > __max) \
__value = __max; \
__value; \
})
/** Helpers to print MAC addresses. */
#define BCM43xx_MACFMT "%02x:%02x:%02x:%02x:%02x:%02x"
#define BCM43xx_MACARG(x) ((u8*)(x))[0], ((u8*)(x))[1], \
((u8*)(x))[2], ((u8*)(x))[3], \
((u8*)(x))[4], ((u8*)(x))[5]
#endif /* BCM43xx_H_ */
View Git Blame Copy Permalink