a683b14df8
two reasons: 1. GPIO namings and their mode definitions are conceptually not part of the PXA register definitions 2. this is actually a temporary move in the transition of PXA2xx to use MFP-alike APIs (as what PXA3xx is now doing), so that legacy code will still work and new code can be added in step by step Signed-off-by: eric miao <eric.miao@marvell.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
255 lines
7.0 KiB
C
255 lines
7.0 KiB
C
/*
|
|
* Battery and Power Management code for the Sharp SL-Cxx00
|
|
*
|
|
* Copyright (c) 2005 Richard Purdie
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify
|
|
* it under the terms of the GNU General Public License version 2 as
|
|
* published by the Free Software Foundation.
|
|
*
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/stat.h>
|
|
#include <linux/init.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/apm-emulation.h>
|
|
|
|
#include <asm/irq.h>
|
|
#include <asm/mach-types.h>
|
|
#include <asm/hardware.h>
|
|
#include <asm/hardware/scoop.h>
|
|
|
|
#include <asm/arch/sharpsl.h>
|
|
#include <asm/arch/spitz.h>
|
|
#include <asm/arch/pxa-regs.h>
|
|
#include <asm/arch/pxa2xx-gpio.h>
|
|
#include "sharpsl.h"
|
|
|
|
#define SHARPSL_CHARGE_ON_VOLT 0x99 /* 2.9V */
|
|
#define SHARPSL_CHARGE_ON_TEMP 0xe0 /* 2.9V */
|
|
#define SHARPSL_CHARGE_ON_ACIN_HIGH 0x9b /* 6V */
|
|
#define SHARPSL_CHARGE_ON_ACIN_LOW 0x34 /* 2V */
|
|
#define SHARPSL_FATAL_ACIN_VOLT 182 /* 3.45V */
|
|
#define SHARPSL_FATAL_NOACIN_VOLT 170 /* 3.40V */
|
|
|
|
static int spitz_last_ac_status;
|
|
|
|
static void spitz_charger_init(void)
|
|
{
|
|
pxa_gpio_mode(SPITZ_GPIO_KEY_INT | GPIO_IN);
|
|
pxa_gpio_mode(SPITZ_GPIO_SYNC | GPIO_IN);
|
|
sharpsl_pm_pxa_init();
|
|
}
|
|
|
|
static void spitz_measure_temp(int on)
|
|
{
|
|
if (on)
|
|
set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON);
|
|
else
|
|
reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_ADC_TEMP_ON);
|
|
}
|
|
|
|
static void spitz_charge(int on)
|
|
{
|
|
if (on) {
|
|
if (sharpsl_pm.flags & SHARPSL_SUSPENDED) {
|
|
set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
|
|
reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
|
|
} else {
|
|
reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
|
|
reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
|
|
}
|
|
} else {
|
|
reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_B);
|
|
set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_CHRG_ON);
|
|
}
|
|
}
|
|
|
|
static void spitz_discharge(int on)
|
|
{
|
|
if (on)
|
|
set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A);
|
|
else
|
|
reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_JK_A);
|
|
}
|
|
|
|
/* HACK - For unknown reasons, accurate voltage readings are only made with a load
|
|
on the power bus which the green led on spitz provides */
|
|
static void spitz_discharge1(int on)
|
|
{
|
|
if (on)
|
|
set_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN);
|
|
else
|
|
reset_scoop_gpio(&spitzscoop_device.dev, SPITZ_SCP_LED_GREEN);
|
|
}
|
|
|
|
static void spitz_presuspend(void)
|
|
{
|
|
spitz_last_ac_status = sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN);
|
|
|
|
/* GPIO Sleep Register */
|
|
PGSR0 = 0x00144018;
|
|
PGSR1 = 0x00EF0000;
|
|
if (machine_is_akita()) {
|
|
PGSR2 = 0x2121C000;
|
|
PGSR3 = 0x00600400;
|
|
} else {
|
|
PGSR2 = 0x0121C000;
|
|
PGSR3 = 0x00600000;
|
|
}
|
|
|
|
PGSR0 &= ~SPITZ_GPIO_G0_STROBE_BIT;
|
|
PGSR1 &= ~SPITZ_GPIO_G1_STROBE_BIT;
|
|
PGSR2 &= ~SPITZ_GPIO_G2_STROBE_BIT;
|
|
PGSR3 &= ~SPITZ_GPIO_G3_STROBE_BIT;
|
|
PGSR2 |= GPIO_bit(SPITZ_GPIO_KEY_STROBE0);
|
|
|
|
pxa_gpio_mode(GPIO18_RDY|GPIO_OUT | GPIO_DFLT_HIGH);
|
|
|
|
PRER = GPIO_bit(SPITZ_GPIO_KEY_INT);
|
|
PFER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
|
|
PWER = GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET) | PWER_RTC;
|
|
PKWR = GPIO_bit(SPITZ_GPIO_SYNC) | GPIO_bit(SPITZ_GPIO_KEY_INT) | GPIO_bit(SPITZ_GPIO_RESET);
|
|
PKSR = 0xffffffff; // clear
|
|
|
|
/* nRESET_OUT Disable */
|
|
PSLR |= PSLR_SL_ROD;
|
|
|
|
/* Clear reset status */
|
|
RCSR = RCSR_HWR | RCSR_WDR | RCSR_SMR | RCSR_GPR;
|
|
|
|
/* Stop 3.6MHz and drive HIGH to PCMCIA and CS */
|
|
PCFR = PCFR_GPR_EN | PCFR_OPDE;
|
|
}
|
|
|
|
static void spitz_postsuspend(void)
|
|
{
|
|
pxa_gpio_mode(GPIO18_RDY_MD);
|
|
pxa_gpio_mode(10 | GPIO_IN);
|
|
}
|
|
|
|
static int spitz_should_wakeup(unsigned int resume_on_alarm)
|
|
{
|
|
int is_resume = 0;
|
|
int acin = sharpsl_pm.machinfo->read_devdata(SHARPSL_STATUS_ACIN);
|
|
|
|
if (spitz_last_ac_status != acin) {
|
|
if (acin) {
|
|
/* charge on */
|
|
sharpsl_pm.flags |= SHARPSL_DO_OFFLINE_CHRG;
|
|
dev_dbg(sharpsl_pm.dev, "AC Inserted\n");
|
|
} else {
|
|
/* charge off */
|
|
dev_dbg(sharpsl_pm.dev, "AC Removed\n");
|
|
sharpsl_pm_led(SHARPSL_LED_OFF);
|
|
sharpsl_pm.machinfo->charge(0);
|
|
sharpsl_pm.charge_mode = CHRG_OFF;
|
|
}
|
|
spitz_last_ac_status = acin;
|
|
/* Return to suspend as this must be what we were woken for */
|
|
return 0;
|
|
}
|
|
|
|
if (PEDR & GPIO_bit(SPITZ_GPIO_KEY_INT))
|
|
is_resume |= GPIO_bit(SPITZ_GPIO_KEY_INT);
|
|
|
|
if (PKSR & GPIO_bit(SPITZ_GPIO_SYNC))
|
|
is_resume |= GPIO_bit(SPITZ_GPIO_SYNC);
|
|
|
|
if (resume_on_alarm && (PEDR & PWER_RTC))
|
|
is_resume |= PWER_RTC;
|
|
|
|
dev_dbg(sharpsl_pm.dev, "is_resume: %x\n",is_resume);
|
|
return is_resume;
|
|
}
|
|
|
|
static unsigned long spitz_charger_wakeup(void)
|
|
{
|
|
return (~GPLR0 & GPIO_bit(SPITZ_GPIO_KEY_INT)) | (GPLR0 & GPIO_bit(SPITZ_GPIO_SYNC));
|
|
}
|
|
|
|
unsigned long spitzpm_read_devdata(int type)
|
|
{
|
|
switch(type) {
|
|
case SHARPSL_STATUS_ACIN:
|
|
return (((~GPLR(SPITZ_GPIO_AC_IN)) & GPIO_bit(SPITZ_GPIO_AC_IN)) != 0);
|
|
case SHARPSL_STATUS_LOCK:
|
|
return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batlock);
|
|
case SHARPSL_STATUS_CHRGFULL:
|
|
return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_batfull);
|
|
case SHARPSL_STATUS_FATAL:
|
|
return READ_GPIO_BIT(sharpsl_pm.machinfo->gpio_fatal);
|
|
case SHARPSL_ACIN_VOLT:
|
|
return sharpsl_pm_pxa_read_max1111(MAX1111_ACIN_VOLT);
|
|
case SHARPSL_BATT_TEMP:
|
|
return sharpsl_pm_pxa_read_max1111(MAX1111_BATT_TEMP);
|
|
case SHARPSL_BATT_VOLT:
|
|
default:
|
|
return sharpsl_pm_pxa_read_max1111(MAX1111_BATT_VOLT);
|
|
}
|
|
}
|
|
|
|
struct sharpsl_charger_machinfo spitz_pm_machinfo = {
|
|
.init = spitz_charger_init,
|
|
.exit = sharpsl_pm_pxa_remove,
|
|
.gpio_batlock = SPITZ_GPIO_BAT_COVER,
|
|
.gpio_acin = SPITZ_GPIO_AC_IN,
|
|
.gpio_batfull = SPITZ_GPIO_CHRG_FULL,
|
|
.batfull_irq = 1,
|
|
.gpio_fatal = SPITZ_GPIO_FATAL_BAT,
|
|
.discharge = spitz_discharge,
|
|
.discharge1 = spitz_discharge1,
|
|
.charge = spitz_charge,
|
|
.measure_temp = spitz_measure_temp,
|
|
.presuspend = spitz_presuspend,
|
|
.postsuspend = spitz_postsuspend,
|
|
.read_devdata = spitzpm_read_devdata,
|
|
.charger_wakeup = spitz_charger_wakeup,
|
|
.should_wakeup = spitz_should_wakeup,
|
|
.backlight_limit = corgibl_limit_intensity,
|
|
.charge_on_volt = SHARPSL_CHARGE_ON_VOLT,
|
|
.charge_on_temp = SHARPSL_CHARGE_ON_TEMP,
|
|
.charge_acin_high = SHARPSL_CHARGE_ON_ACIN_HIGH,
|
|
.charge_acin_low = SHARPSL_CHARGE_ON_ACIN_LOW,
|
|
.fatal_acin_volt = SHARPSL_FATAL_ACIN_VOLT,
|
|
.fatal_noacin_volt= SHARPSL_FATAL_NOACIN_VOLT,
|
|
.bat_levels = 40,
|
|
.bat_levels_noac = spitz_battery_levels_noac,
|
|
.bat_levels_acin = spitz_battery_levels_acin,
|
|
.status_high_acin = 188,
|
|
.status_low_acin = 178,
|
|
.status_high_noac = 185,
|
|
.status_low_noac = 175,
|
|
};
|
|
|
|
static struct platform_device *spitzpm_device;
|
|
|
|
static int __devinit spitzpm_init(void)
|
|
{
|
|
int ret;
|
|
|
|
spitzpm_device = platform_device_alloc("sharpsl-pm", -1);
|
|
if (!spitzpm_device)
|
|
return -ENOMEM;
|
|
|
|
spitzpm_device->dev.platform_data = &spitz_pm_machinfo;
|
|
ret = platform_device_add(spitzpm_device);
|
|
|
|
if (ret)
|
|
platform_device_put(spitzpm_device);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void spitzpm_exit(void)
|
|
{
|
|
platform_device_unregister(spitzpm_device);
|
|
}
|
|
|
|
module_init(spitzpm_init);
|
|
module_exit(spitzpm_exit);
|