6c4e1ef46c
Introduce new kernel config symbol for Microchip usb5744 SMBus programming
support. Since usb5744 i2c initialization routine uses i2c SMBus APIs these
APIs should only be invoked when kernel has I2C support. This new kernel
config describes the dependency on I2C kernel support and fix the below
build issues when USB_ONBOARD_DEV=y and CONFIG_I2C=m.
riscv64-linux-ld: drivers/usb/misc/onboard_usb_dev.o:
undefined reference to `i2c_find_device_by_fwnode'
drivers/usb/misc/onboard_usb_dev.c:408:(.text+0xb24): undefined
reference to `i2c_smbus_write_block_data'
<snip>
Parsing of the i2c-bus bus handle is not put under usb5744 kernel config
check as the intention is to report an error when DT is configured for
usb5744 SMBus support and kernel has USB_ONBOARD_DEV_USB5744 disabled.
Fixes: 6782311d04 ("usb: misc: onboard_usb_dev: add Microchip usb5744 SMBus programming support")
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Suggested-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202409140539.3Axwv38m-lkp@intel.com/
Acked-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Link: https://lore.kernel.org/r/1727529992-476088-1-git-send-email-radhey.shyam.pandey@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
346 lines
12 KiB
Plaintext
346 lines
12 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0
|
|
#
|
|
# USB Miscellaneous driver configuration
|
|
#
|
|
comment "USB Miscellaneous drivers"
|
|
|
|
config USB_USS720
|
|
tristate "USS720 parport driver"
|
|
depends on PARPORT
|
|
select PARPORT_NOT_PC
|
|
help
|
|
This driver is for USB parallel port adapters that use the Lucent
|
|
Technologies USS-720 chip. These cables are plugged into your USB
|
|
port and provide USB compatibility to peripherals designed with
|
|
parallel port interfaces.
|
|
|
|
The chip has two modes: automatic mode and manual mode. In automatic
|
|
mode, it looks to the computer like a standard USB printer. Only
|
|
printers may be connected to the USS-720 in this mode. The generic
|
|
USB printer driver ("USB Printer support", above) may be used in
|
|
that mode, and you can say N here if you want to use the chip only
|
|
in this mode.
|
|
|
|
Manual mode is not limited to printers, any parallel port
|
|
device should work. This driver utilizes manual mode.
|
|
Note however that some operations are three orders of magnitude
|
|
slower than on a PCI/ISA Parallel Port, so timing critical
|
|
applications might not work.
|
|
|
|
Say Y here if you own an USS-720 USB->Parport cable and intend to
|
|
connect anything other than a printer to it.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called uss720.
|
|
|
|
config USB_EMI62
|
|
tristate "EMI 6|2m USB Audio interface support"
|
|
help
|
|
This driver loads firmware to Emagic EMI 6|2m low latency USB
|
|
Audio and Midi interface.
|
|
|
|
After firmware load the device is handled with standard linux
|
|
USB Audio driver.
|
|
|
|
This code is also available as a module ( = code which can be
|
|
inserted in and removed from the running kernel whenever you want).
|
|
The module will be called audio. If you want to compile it as a
|
|
module, say M here and read <file:Documentation/kbuild/modules.rst>.
|
|
|
|
config USB_EMI26
|
|
tristate "EMI 2|6 USB Audio interface support"
|
|
help
|
|
This driver loads firmware to Emagic EMI 2|6 low latency USB
|
|
Audio interface.
|
|
|
|
After firmware load the device is handled with standard linux
|
|
USB Audio driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called emi26.
|
|
|
|
config USB_ADUTUX
|
|
tristate "ADU devices from Ontrak Control Systems"
|
|
help
|
|
Say Y if you want to use an ADU device from Ontrak Control
|
|
Systems.
|
|
|
|
To compile this driver as a module, choose M here. The module
|
|
will be called adutux.
|
|
|
|
config USB_SEVSEG
|
|
tristate "USB 7-Segment LED Display"
|
|
help
|
|
Say Y here if you have a USB 7-Segment Display by Delcom
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called usbsevseg.
|
|
|
|
config USB_LEGOTOWER
|
|
tristate "USB Lego Infrared Tower support"
|
|
help
|
|
Say Y here if you want to connect a USB Lego Infrared Tower to your
|
|
computer's USB port.
|
|
|
|
This code is also available as a module ( = code which can be
|
|
inserted in and removed from the running kernel whenever you want).
|
|
The module will be called legousbtower. If you want to compile it as
|
|
a module, say M here and read
|
|
<file:Documentation/kbuild/modules.rst>.
|
|
|
|
config USB_LCD
|
|
tristate "USB LCD driver support"
|
|
help
|
|
Say Y here if you want to connect an USBLCD to your computer's
|
|
USB port. The USBLCD is a small USB interface board for
|
|
alphanumeric LCD modules. See <http://www.usblcd.de/> for more
|
|
information.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called usblcd.
|
|
|
|
config USB_CYPRESS_CY7C63
|
|
tristate "Cypress CY7C63xxx USB driver support"
|
|
help
|
|
Say Y here if you want to connect a Cypress CY7C63xxx
|
|
micro controller to your computer's USB port. Currently this
|
|
driver supports the pre-programmed devices (incl. firmware)
|
|
by AK Modul-Bus Computer GmbH.
|
|
|
|
Please see: https://www.ak-modul-bus.de/stat/mikrocontroller.html
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called cypress_cy7c63.
|
|
|
|
config USB_CYTHERM
|
|
tristate "Cypress USB thermometer driver support"
|
|
help
|
|
Say Y here if you want to connect a Cypress USB thermometer
|
|
device to your computer's USB port. This device is also known
|
|
as the Cypress USB Starter kit or demo board. The Elektor
|
|
magazine published a modified version of this device in issue
|
|
#291.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called cytherm.
|
|
|
|
config USB_IDMOUSE
|
|
tristate "Siemens ID USB Mouse Fingerprint sensor support"
|
|
help
|
|
Say Y here if you want to use the fingerprint sensor on
|
|
the Siemens ID Mouse. There is also a Siemens ID Mouse
|
|
_Professional_, which has not been tested with this driver,
|
|
but uses the same sensor and may therefore work.
|
|
|
|
This driver creates an entry "/dev/idmouseX" or "/dev/usb/idmouseX",
|
|
which can be used by, e.g.,"cat /dev/idmouse0 > fingerprint.pnm".
|
|
|
|
See also <https://www.fs.tum.de/~echtler/idmouse/>.
|
|
|
|
config USB_APPLEDISPLAY
|
|
tristate "Apple Cinema Display support"
|
|
select BACKLIGHT_CLASS_DEVICE
|
|
help
|
|
Say Y here if you want to control the backlight of Apple Cinema
|
|
Displays over USB. This driver provides a sysfs interface.
|
|
|
|
config USB_QCOM_EUD
|
|
tristate "QCOM Embedded USB Debugger(EUD) Driver"
|
|
depends on ARCH_QCOM || COMPILE_TEST
|
|
select USB_ROLE_SWITCH
|
|
help
|
|
This module enables support for Qualcomm Technologies, Inc.
|
|
Embedded USB Debugger (EUD). The EUD is a control peripheral
|
|
which reports VBUS attach/detach events and has USB-based
|
|
debug and trace capabilities. On selecting m, the module name
|
|
that is built is qcom_eud.ko
|
|
|
|
config APPLE_MFI_FASTCHARGE
|
|
tristate "Fast charge control for iOS devices"
|
|
select POWER_SUPPLY
|
|
help
|
|
Say Y here if you want to control whether iOS devices will
|
|
fast charge from the USB interface, as implemented in "MFi"
|
|
chargers.
|
|
|
|
It is safe to say M here.
|
|
|
|
config USB_LJCA
|
|
tristate "Intel La Jolla Cove Adapter support"
|
|
select AUXILIARY_BUS
|
|
depends on USB && ACPI
|
|
help
|
|
This adds support for Intel La Jolla Cove USB-I2C/SPI/GPIO
|
|
Master Adapter (LJCA). Additional drivers such as I2C_LJCA,
|
|
GPIO_LJCA and SPI_LJCA must be enabled in order to use the
|
|
functionality of the device.
|
|
|
|
This driver can also be built as a module. If so, the module
|
|
will be called usb-ljca.
|
|
|
|
source "drivers/usb/misc/sisusbvga/Kconfig"
|
|
|
|
config USB_LD
|
|
tristate "USB LD driver"
|
|
help
|
|
This driver is for generic USB devices that use interrupt transfers,
|
|
like LD Didactic's USB devices.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ldusb.
|
|
|
|
config USB_TRANCEVIBRATOR
|
|
tristate "PlayStation 2 Trance Vibrator driver support"
|
|
help
|
|
Say Y here if you want to connect a PlayStation 2 Trance Vibrator
|
|
device to your computer's USB port.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called trancevibrator.
|
|
|
|
config USB_IOWARRIOR
|
|
tristate "IO Warrior driver support"
|
|
help
|
|
Say Y here if you want to support the IO Warrior devices from Code
|
|
Mercenaries. This includes support for the following devices:
|
|
IO Warrior 40
|
|
IO Warrior 24
|
|
IO Warrior 56
|
|
IO Warrior 24 Power Vampire
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called iowarrior.
|
|
|
|
config USB_TEST
|
|
tristate "USB testing driver"
|
|
help
|
|
This driver is for testing host controller software. It is used
|
|
with specialized device firmware for regression and stress testing,
|
|
to help prevent problems from cropping up with "real" drivers.
|
|
|
|
See <http://www.linux-usb.org/usbtest/> for more information,
|
|
including sample test device firmware and "how to use it".
|
|
|
|
config USB_EHSET_TEST_FIXTURE
|
|
tristate "USB EHSET Test Fixture driver"
|
|
help
|
|
Say Y here if you want to support the special test fixture device
|
|
used for the USB-IF Embedded Host High-Speed Electrical Test procedure.
|
|
|
|
When the test fixture is connected, it can enumerate as one of several
|
|
VID/PID pairs. This driver then initiates a corresponding test mode on
|
|
the downstream port to which the test fixture is attached.
|
|
|
|
See <http://www.usb.org/developers/onthego/EHSET_v1.01.pdf> for more
|
|
information.
|
|
|
|
config USB_ISIGHTFW
|
|
tristate "iSight firmware loading support"
|
|
select FW_LOADER
|
|
help
|
|
This driver loads firmware for USB Apple iSight cameras, allowing
|
|
them to be driven by the USB video class driver available at
|
|
http://linux-uvc.berlios.de
|
|
|
|
The firmware for this driver must be extracted from the MacOS
|
|
driver beforehand. Tools for doing so are available at
|
|
http://bersace03.free.fr
|
|
|
|
config USB_YUREX
|
|
tristate "USB YUREX driver support"
|
|
help
|
|
Say Y here if you want to connect a YUREX to your computer's
|
|
USB port. The YUREX is a leg-shakes sensor. See
|
|
<http://bbu.kayac.com/en/> for further information.
|
|
This driver supports read/write of leg-shakes counter and
|
|
fasync for the counter update via a device file /dev/yurex*.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called yurex.
|
|
|
|
config USB_EZUSB_FX2
|
|
tristate "Functions for loading firmware on EZUSB chips"
|
|
help
|
|
Say Y here if you need EZUSB device support.
|
|
(Cypress FX/FX2/FX2LP microcontrollers)
|
|
|
|
config USB_HUB_USB251XB
|
|
tristate "USB251XB Hub Controller Configuration Driver"
|
|
depends on I2C
|
|
help
|
|
This option enables support for configuration via SMBus of the
|
|
Microchip USB251x/xBi USB 2.0 Hub Controller series. Configuration
|
|
parameters may be set in devicetree or platform data.
|
|
Say Y or M here if you need to configure such a device via SMBus.
|
|
|
|
config USB_HSIC_USB3503
|
|
tristate "USB3503 HSIC to USB20 Driver"
|
|
depends on I2C
|
|
select REGMAP_I2C
|
|
help
|
|
This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver.
|
|
|
|
config USB_HSIC_USB4604
|
|
tristate "USB4604 HSIC to USB20 Driver"
|
|
depends on I2C
|
|
help
|
|
This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver.
|
|
|
|
config USB_LINK_LAYER_TEST
|
|
tristate "USB Link Layer Test driver"
|
|
help
|
|
This driver is for generating specific traffic for Super Speed Link
|
|
Layer Test Device. Say Y only when you want to conduct USB Super Speed
|
|
Link Layer Test for host controllers.
|
|
|
|
config USB_CHAOSKEY
|
|
tristate "ChaosKey random number generator driver support"
|
|
depends on HW_RANDOM
|
|
help
|
|
Say Y here if you want to connect an AltusMetrum ChaosKey or
|
|
Araneus Alea I to your computer's USB port. These devices
|
|
are hardware random number generators which hook into the
|
|
kernel entropy pool to ensure a large supply of entropy for
|
|
/dev/random and /dev/urandom and also provides direct access
|
|
via /dev/chaoskeyX
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called chaoskey.
|
|
|
|
config BRCM_USB_PINMAP
|
|
tristate "Broadcom pinmap driver support"
|
|
depends on (ARCH_BRCMSTB && PHY_BRCM_USB) || COMPILE_TEST
|
|
default ARCH_BRCMSTB && PHY_BRCM_USB
|
|
help
|
|
This option enables support for remapping some USB external
|
|
signals, which are typically on dedicated pins on the chip,
|
|
to any gpio.
|
|
|
|
config USB_ONBOARD_DEV
|
|
tristate "Onboard USB device support"
|
|
depends on OF
|
|
help
|
|
Say Y here if you want to support discrete onboard USB devices
|
|
that don't require an additional control bus for initialization,
|
|
but need some non-trivial form of initialization, such as
|
|
enabling a power regulator. An example for such device is the
|
|
Realtek RTS5411 hub.
|
|
|
|
This driver can be used as a module but its state (module vs
|
|
builtin) must match the state of the USB subsystem. Enabling
|
|
this config will enable the driver and it will automatically
|
|
match the state of the USB subsystem. If this driver is a
|
|
module it will be called onboard_usb_dev.
|
|
|
|
config USB_ONBOARD_DEV_USB5744
|
|
bool "Onboard USB Microchip usb5744 hub with SMBus support"
|
|
depends on (USB_ONBOARD_DEV && I2C=y) || (USB_ONBOARD_DEV=m && I2C=m)
|
|
help
|
|
Say Y here if you want to support onboard USB Microchip usb5744
|
|
hub that requires SMBus initialization.
|
|
|
|
This options enables usb5744 i2c default initialization sequence
|
|
during hub start-up configuration stage. It is must to enable this
|
|
option on AMD Kria KR260 Robotics Starter Kit as this hub is
|
|
connected to USB-SD converter which mounts the root filesystem.
|