fdd8a532a6
Updated the multiqueue.txt document to call out the correct kernel options to select to enable multiqueue. Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
116 lines
5.0 KiB
Plaintext
116 lines
5.0 KiB
Plaintext
|
|
HOWTO for multiqueue network device support
|
|
===========================================
|
|
|
|
Section 1: Base driver requirements for implementing multiqueue support
|
|
Section 2: Qdisc support for multiqueue devices
|
|
Section 3: Brief howto using PRIO or RR for multiqueue devices
|
|
|
|
|
|
Intro: Kernel support for multiqueue devices
|
|
---------------------------------------------------------
|
|
|
|
Kernel support for multiqueue devices is only an API that is presented to the
|
|
netdevice layer for base drivers to implement. This feature is part of the
|
|
core networking stack, and all network devices will be running on the
|
|
multiqueue-aware stack. If a base driver only has one queue, then these
|
|
changes are transparent to that driver.
|
|
|
|
|
|
Section 1: Base driver requirements for implementing multiqueue support
|
|
-----------------------------------------------------------------------
|
|
|
|
Base drivers are required to use the new alloc_etherdev_mq() or
|
|
alloc_netdev_mq() functions to allocate the subqueues for the device. The
|
|
underlying kernel API will take care of the allocation and deallocation of
|
|
the subqueue memory, as well as netdev configuration of where the queues
|
|
exist in memory.
|
|
|
|
The base driver will also need to manage the queues as it does the global
|
|
netdev->queue_lock today. Therefore base drivers should use the
|
|
netif_{start|stop|wake}_subqueue() functions to manage each queue while the
|
|
device is still operational. netdev->queue_lock is still used when the device
|
|
comes online or when it's completely shut down (unregister_netdev(), etc.).
|
|
|
|
Finally, the base driver should indicate that it is a multiqueue device. The
|
|
feature flag NETIF_F_MULTI_QUEUE should be added to the netdev->features
|
|
bitmap on device initialization. Below is an example from e1000:
|
|
|
|
#ifdef CONFIG_E1000_MQ
|
|
if ( (adapter->hw.mac.type == e1000_82571) ||
|
|
(adapter->hw.mac.type == e1000_82572) ||
|
|
(adapter->hw.mac.type == e1000_80003es2lan))
|
|
netdev->features |= NETIF_F_MULTI_QUEUE;
|
|
#endif
|
|
|
|
|
|
Section 2: Qdisc support for multiqueue devices
|
|
-----------------------------------------------
|
|
|
|
Currently two qdiscs support multiqueue devices. A new round-robin qdisc,
|
|
sch_rr, and sch_prio. The qdisc is responsible for classifying the skb's to
|
|
bands and queues, and will store the queue mapping into skb->queue_mapping.
|
|
Use this field in the base driver to determine which queue to send the skb
|
|
to.
|
|
|
|
sch_rr has been added for hardware that doesn't want scheduling policies from
|
|
software, so it's a straight round-robin qdisc. It uses the same syntax and
|
|
classification priomap that sch_prio uses, so it should be intuitive to
|
|
configure for people who've used sch_prio.
|
|
|
|
In order to utilitize the multiqueue features of the qdiscs, the network
|
|
device layer needs to enable multiple queue support. This can be done by
|
|
selecting NETDEVICES_MULTIQUEUE under Drivers.
|
|
|
|
The PRIO qdisc naturally plugs into a multiqueue device. If
|
|
NETDEVICES_MULTIQUEUE is selected, then on qdisc load, the number of
|
|
bands requested is compared to the number of queues on the hardware. If they
|
|
are equal, it sets a one-to-one mapping up between the queues and bands. If
|
|
they're not equal, it will not load the qdisc. This is the same behavior
|
|
for RR. Once the association is made, any skb that is classified will have
|
|
skb->queue_mapping set, which will allow the driver to properly queue skb's
|
|
to multiple queues.
|
|
|
|
|
|
Section 3: Brief howto using PRIO and RR for multiqueue devices
|
|
---------------------------------------------------------------
|
|
|
|
The userspace command 'tc,' part of the iproute2 package, is used to configure
|
|
qdiscs. To add the PRIO qdisc to your network device, assuming the device is
|
|
called eth0, run the following command:
|
|
|
|
# tc qdisc add dev eth0 root handle 1: prio bands 4 multiqueue
|
|
|
|
This will create 4 bands, 0 being highest priority, and associate those bands
|
|
to the queues on your NIC. Assuming eth0 has 4 Tx queues, the band mapping
|
|
would look like:
|
|
|
|
band 0 => queue 0
|
|
band 1 => queue 1
|
|
band 2 => queue 2
|
|
band 3 => queue 3
|
|
|
|
Traffic will begin flowing through each queue if your TOS values are assigning
|
|
traffic across the various bands. For example, ssh traffic will always try to
|
|
go out band 0 based on TOS -> Linux priority conversion (realtime traffic),
|
|
so it will be sent out queue 0. ICMP traffic (pings) fall into the "normal"
|
|
traffic classification, which is band 1. Therefore pings will be send out
|
|
queue 1 on the NIC.
|
|
|
|
Note the use of the multiqueue keyword. This is only in versions of iproute2
|
|
that support multiqueue networking devices; if this is omitted when loading
|
|
a qdisc onto a multiqueue device, the qdisc will load and operate the same
|
|
if it were loaded onto a single-queue device (i.e. - sends all traffic to
|
|
queue 0).
|
|
|
|
Another alternative to multiqueue band allocation can be done by using the
|
|
multiqueue option and specify 0 bands. If this is the case, the qdisc will
|
|
allocate the number of bands to equal the number of queues that the device
|
|
reports, and bring the qdisc online.
|
|
|
|
The behavior of tc filters remains the same, where it will override TOS priority
|
|
classification.
|
|
|
|
|
|
Author: Peter P. Waskiewicz Jr. <peter.p.waskiewicz.jr@intel.com>
|