390167efa3
Currently there are several dts that don't specify address or size cells for the muram. This causes dtc to use default values, one of which is an address-cells of two, and this breaks the parsing of the muram ranges, which is assuming an address-cells of one. For example: Warning (reg_format): "reg" property in /qe@e0100000/muram@10000/data-only@0 has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1) Explicitly setting the address and size cells gets it parsed properly and gets rid of the four dtc warnings. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
397 lines
9.1 KiB
Plaintext
397 lines
9.1 KiB
Plaintext
/*
|
|
* MPC8323E EMDS Device Tree Source
|
|
*
|
|
* Copyright 2006 Freescale Semiconductor Inc.
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
|
|
* To enable external serial I/O on a Freescale MPC 8323 SYS/MDS board, do
|
|
* this:
|
|
*
|
|
* 1) On chip U61, lift (disconnect) pins 21 (TXD) and 22 (RXD) from the board.
|
|
* 2) Solder a wire from U61-21 to P19A-23. P19 is a grid of pins on the board
|
|
* next to the serial ports.
|
|
* 3) Solder a wire from U61-22 to P19K-22.
|
|
*
|
|
* Note that there's a typo in the schematic. The board labels the last column
|
|
* of pins "P19K", but in the schematic, that column is called "P19J". So if
|
|
* you're going by the schematic, the pin is called "P19J-K22".
|
|
*/
|
|
|
|
/ {
|
|
model = "MPC8323EMDS";
|
|
compatible = "MPC8323EMDS", "MPC832xMDS", "MPC83xxMDS";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
aliases {
|
|
ethernet0 = &enet0;
|
|
ethernet1 = &enet1;
|
|
serial0 = &serial0;
|
|
serial1 = &serial1;
|
|
pci0 = &pci0;
|
|
};
|
|
|
|
cpus {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
PowerPC,8323@0 {
|
|
device_type = "cpu";
|
|
reg = <0>;
|
|
d-cache-line-size = <20>; // 32 bytes
|
|
i-cache-line-size = <20>; // 32 bytes
|
|
d-cache-size = <4000>; // L1, 16K
|
|
i-cache-size = <4000>; // L1, 16K
|
|
timebase-frequency = <0>;
|
|
bus-frequency = <0>;
|
|
clock-frequency = <0>;
|
|
};
|
|
};
|
|
|
|
memory {
|
|
device_type = "memory";
|
|
reg = <00000000 08000000>;
|
|
};
|
|
|
|
bcsr@f8000000 {
|
|
device_type = "board-control";
|
|
reg = <f8000000 8000>;
|
|
};
|
|
|
|
soc8323@e0000000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
device_type = "soc";
|
|
ranges = <0 e0000000 00100000>;
|
|
reg = <e0000000 00000200>;
|
|
bus-frequency = <7DE2900>;
|
|
|
|
wdt@200 {
|
|
device_type = "watchdog";
|
|
compatible = "mpc83xx_wdt";
|
|
reg = <200 100>;
|
|
};
|
|
|
|
i2c@3000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
cell-index = <0>;
|
|
compatible = "fsl-i2c";
|
|
reg = <3000 100>;
|
|
interrupts = <e 8>;
|
|
interrupt-parent = < &ipic >;
|
|
dfsrr;
|
|
|
|
rtc@68 {
|
|
compatible = "dallas,ds1374";
|
|
reg = <68>;
|
|
};
|
|
};
|
|
|
|
serial0: serial@4500 {
|
|
cell-index = <0>;
|
|
device_type = "serial";
|
|
compatible = "ns16550";
|
|
reg = <4500 100>;
|
|
clock-frequency = <0>;
|
|
interrupts = <9 8>;
|
|
interrupt-parent = < &ipic >;
|
|
};
|
|
|
|
serial1: serial@4600 {
|
|
cell-index = <1>;
|
|
device_type = "serial";
|
|
compatible = "ns16550";
|
|
reg = <4600 100>;
|
|
clock-frequency = <0>;
|
|
interrupts = <a 8>;
|
|
interrupt-parent = < &ipic >;
|
|
};
|
|
|
|
crypto@30000 {
|
|
device_type = "crypto";
|
|
model = "SEC2";
|
|
compatible = "talitos";
|
|
reg = <30000 7000>;
|
|
interrupts = <b 8>;
|
|
interrupt-parent = < &ipic >;
|
|
/* Rev. 2.2 */
|
|
num-channels = <1>;
|
|
channel-fifo-len = <18>;
|
|
exec-units-mask = <0000004c>;
|
|
descriptor-types-mask = <0122003f>;
|
|
};
|
|
|
|
ipic: pic@700 {
|
|
interrupt-controller;
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <2>;
|
|
reg = <700 100>;
|
|
device_type = "ipic";
|
|
};
|
|
|
|
par_io@1400 {
|
|
reg = <1400 100>;
|
|
device_type = "par_io";
|
|
num-ports = <7>;
|
|
|
|
pio3: ucc_pin@03 {
|
|
pio-map = <
|
|
/* port pin dir open_drain assignment has_irq */
|
|
3 4 3 0 2 0 /* MDIO */
|
|
3 5 1 0 2 0 /* MDC */
|
|
0 d 2 0 1 0 /* RX_CLK (CLK9) */
|
|
3 18 2 0 1 0 /* TX_CLK (CLK10) */
|
|
1 0 1 0 1 0 /* TxD0 */
|
|
1 1 1 0 1 0 /* TxD1 */
|
|
1 2 1 0 1 0 /* TxD2 */
|
|
1 3 1 0 1 0 /* TxD3 */
|
|
1 4 2 0 1 0 /* RxD0 */
|
|
1 5 2 0 1 0 /* RxD1 */
|
|
1 6 2 0 1 0 /* RxD2 */
|
|
1 7 2 0 1 0 /* RxD3 */
|
|
1 8 2 0 1 0 /* RX_ER */
|
|
1 9 1 0 1 0 /* TX_ER */
|
|
1 a 2 0 1 0 /* RX_DV */
|
|
1 b 2 0 1 0 /* COL */
|
|
1 c 1 0 1 0 /* TX_EN */
|
|
1 d 2 0 1 0>;/* CRS */
|
|
};
|
|
pio4: ucc_pin@04 {
|
|
pio-map = <
|
|
/* port pin dir open_drain assignment has_irq */
|
|
3 1f 2 0 1 0 /* RX_CLK (CLK7) */
|
|
3 6 2 0 1 0 /* TX_CLK (CLK8) */
|
|
1 12 1 0 1 0 /* TxD0 */
|
|
1 13 1 0 1 0 /* TxD1 */
|
|
1 14 1 0 1 0 /* TxD2 */
|
|
1 15 1 0 1 0 /* TxD3 */
|
|
1 16 2 0 1 0 /* RxD0 */
|
|
1 17 2 0 1 0 /* RxD1 */
|
|
1 18 2 0 1 0 /* RxD2 */
|
|
1 19 2 0 1 0 /* RxD3 */
|
|
1 1a 2 0 1 0 /* RX_ER */
|
|
1 1b 1 0 1 0 /* TX_ER */
|
|
1 1c 2 0 1 0 /* RX_DV */
|
|
1 1d 2 0 1 0 /* COL */
|
|
1 1e 1 0 1 0 /* TX_EN */
|
|
1 1f 2 0 1 0>;/* CRS */
|
|
};
|
|
pio5: ucc_pin@05 {
|
|
pio-map = <
|
|
/*
|
|
* open has
|
|
* port pin dir drain sel irq
|
|
*/
|
|
2 0 1 0 2 0 /* TxD5 */
|
|
2 8 2 0 2 0 /* RxD5 */
|
|
|
|
2 1d 2 0 0 0 /* CTS5 */
|
|
2 1f 1 0 2 0 /* RTS5 */
|
|
|
|
2 18 2 0 0 0 /* CD */
|
|
|
|
>;
|
|
};
|
|
|
|
};
|
|
};
|
|
|
|
qe@e0100000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
device_type = "qe";
|
|
compatible = "fsl,qe";
|
|
ranges = <0 e0100000 00100000>;
|
|
reg = <e0100000 480>;
|
|
brg-frequency = <0>;
|
|
bus-frequency = <BCD3D80>;
|
|
|
|
muram@10000 {
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
compatible = "fsl,qe-muram", "fsl,cpm-muram";
|
|
ranges = <0 00010000 00004000>;
|
|
|
|
data-only@0 {
|
|
compatible = "fsl,qe-muram-data",
|
|
"fsl,cpm-muram-data";
|
|
reg = <0 4000>;
|
|
};
|
|
};
|
|
|
|
spi@4c0 {
|
|
cell-index = <0>;
|
|
compatible = "fsl,spi";
|
|
reg = <4c0 40>;
|
|
interrupts = <2>;
|
|
interrupt-parent = < &qeic >;
|
|
mode = "cpu";
|
|
};
|
|
|
|
spi@500 {
|
|
cell-index = <1>;
|
|
compatible = "fsl,spi";
|
|
reg = <500 40>;
|
|
interrupts = <1>;
|
|
interrupt-parent = < &qeic >;
|
|
mode = "cpu";
|
|
};
|
|
|
|
usb@6c0 {
|
|
compatible = "qe_udc";
|
|
reg = <6c0 40 8B00 100>;
|
|
interrupts = <b>;
|
|
interrupt-parent = < &qeic >;
|
|
mode = "slave";
|
|
};
|
|
|
|
enet0: ucc@2200 {
|
|
device_type = "network";
|
|
compatible = "ucc_geth";
|
|
model = "UCC";
|
|
cell-index = <3>;
|
|
device-id = <3>;
|
|
reg = <2200 200>;
|
|
interrupts = <22>;
|
|
interrupt-parent = < &qeic >;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
rx-clock-name = "clk9";
|
|
tx-clock-name = "clk10";
|
|
phy-handle = < &phy3 >;
|
|
pio-handle = < &pio3 >;
|
|
};
|
|
|
|
enet1: ucc@3200 {
|
|
device_type = "network";
|
|
compatible = "ucc_geth";
|
|
model = "UCC";
|
|
cell-index = <4>;
|
|
device-id = <4>;
|
|
reg = <3200 200>;
|
|
interrupts = <23>;
|
|
interrupt-parent = < &qeic >;
|
|
local-mac-address = [ 00 00 00 00 00 00 ];
|
|
rx-clock-name = "clk7";
|
|
tx-clock-name = "clk8";
|
|
phy-handle = < &phy4 >;
|
|
pio-handle = < &pio4 >;
|
|
};
|
|
|
|
ucc@2400 {
|
|
device_type = "serial";
|
|
compatible = "ucc_uart";
|
|
model = "UCC";
|
|
device-id = <5>; /* The UCC number, 1-7*/
|
|
port-number = <0>; /* Which ttyQEx device */
|
|
soft-uart; /* We need Soft-UART */
|
|
reg = <2400 200>;
|
|
interrupts = <28>; /* From Table 18-12 */
|
|
interrupt-parent = < &qeic >;
|
|
/*
|
|
* For Soft-UART, we need to set TX to 1X, which
|
|
* means specifying separate clock sources.
|
|
*/
|
|
rx-clock-name = "brg5";
|
|
tx-clock-name = "brg6";
|
|
pio-handle = < &pio5 >;
|
|
};
|
|
|
|
|
|
mdio@2320 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
reg = <2320 18>;
|
|
compatible = "fsl,ucc-mdio";
|
|
|
|
phy3: ethernet-phy@03 {
|
|
interrupt-parent = < &ipic >;
|
|
interrupts = <11 8>;
|
|
reg = <3>;
|
|
device_type = "ethernet-phy";
|
|
};
|
|
phy4: ethernet-phy@04 {
|
|
interrupt-parent = < &ipic >;
|
|
interrupts = <12 8>;
|
|
reg = <4>;
|
|
device_type = "ethernet-phy";
|
|
};
|
|
};
|
|
|
|
qeic: interrupt-controller@80 {
|
|
interrupt-controller;
|
|
compatible = "fsl,qe-ic";
|
|
#address-cells = <0>;
|
|
#interrupt-cells = <1>;
|
|
reg = <80 80>;
|
|
big-endian;
|
|
interrupts = <20 8 21 8>; //high:32 low:33
|
|
interrupt-parent = < &ipic >;
|
|
};
|
|
};
|
|
|
|
pci0: pci@e0008500 {
|
|
cell-index = <1>;
|
|
interrupt-map-mask = <f800 0 0 7>;
|
|
interrupt-map = <
|
|
/* IDSEL 0x11 AD17 */
|
|
8800 0 0 1 &ipic 14 8
|
|
8800 0 0 2 &ipic 15 8
|
|
8800 0 0 3 &ipic 16 8
|
|
8800 0 0 4 &ipic 17 8
|
|
|
|
/* IDSEL 0x12 AD18 */
|
|
9000 0 0 1 &ipic 16 8
|
|
9000 0 0 2 &ipic 17 8
|
|
9000 0 0 3 &ipic 14 8
|
|
9000 0 0 4 &ipic 15 8
|
|
|
|
/* IDSEL 0x13 AD19 */
|
|
9800 0 0 1 &ipic 17 8
|
|
9800 0 0 2 &ipic 14 8
|
|
9800 0 0 3 &ipic 15 8
|
|
9800 0 0 4 &ipic 16 8
|
|
|
|
/* IDSEL 0x15 AD21*/
|
|
a800 0 0 1 &ipic 14 8
|
|
a800 0 0 2 &ipic 15 8
|
|
a800 0 0 3 &ipic 16 8
|
|
a800 0 0 4 &ipic 17 8
|
|
|
|
/* IDSEL 0x16 AD22*/
|
|
b000 0 0 1 &ipic 17 8
|
|
b000 0 0 2 &ipic 14 8
|
|
b000 0 0 3 &ipic 15 8
|
|
b000 0 0 4 &ipic 16 8
|
|
|
|
/* IDSEL 0x17 AD23*/
|
|
b800 0 0 1 &ipic 16 8
|
|
b800 0 0 2 &ipic 17 8
|
|
b800 0 0 3 &ipic 14 8
|
|
b800 0 0 4 &ipic 15 8
|
|
|
|
/* IDSEL 0x18 AD24*/
|
|
c000 0 0 1 &ipic 15 8
|
|
c000 0 0 2 &ipic 16 8
|
|
c000 0 0 3 &ipic 17 8
|
|
c000 0 0 4 &ipic 14 8>;
|
|
interrupt-parent = < &ipic >;
|
|
interrupts = <42 8>;
|
|
bus-range = <0 0>;
|
|
ranges = <02000000 0 90000000 90000000 0 10000000
|
|
42000000 0 80000000 80000000 0 10000000
|
|
01000000 0 00000000 d0000000 0 00100000>;
|
|
clock-frequency = <0>;
|
|
#interrupt-cells = <1>;
|
|
#size-cells = <2>;
|
|
#address-cells = <3>;
|
|
reg = <e0008500 100>;
|
|
compatible = "fsl,mpc8349-pci";
|
|
device_type = "pci";
|
|
};
|
|
};
|