7637c9259f
Drop the old geode_gpio crud, as well as the raw outl() calls; instead, use the Linux GPIO API where possible, and the cs5535_gpio API in other places. Note that we don't actually clean up the driver properly yet (once loaded, it always remains loaded). That'll come later.. This patch is necessary for building the driver. Signed-off-by: Andres Salomon <dilinger@queued.net> Cc: Greg KH <greg@kroah.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
123 lines
2.8 KiB
C
123 lines
2.8 KiB
C
/* OLPC machine specific definitions */
|
|
|
|
#ifndef _ASM_X86_OLPC_H
|
|
#define _ASM_X86_OLPC_H
|
|
|
|
#include <asm/geode.h>
|
|
|
|
struct olpc_platform_t {
|
|
int flags;
|
|
uint32_t boardrev;
|
|
int ecver;
|
|
};
|
|
|
|
#define OLPC_F_PRESENT 0x01
|
|
#define OLPC_F_DCON 0x02
|
|
|
|
#ifdef CONFIG_OLPC
|
|
|
|
extern struct olpc_platform_t olpc_platform_info;
|
|
|
|
/*
|
|
* OLPC board IDs contain the major build number within the mask 0x0ff0,
|
|
* and the minor build number withing 0x000f. Pre-builds have a minor
|
|
* number less than 8, and normal builds start at 8. For example, 0x0B10
|
|
* is a PreB1, and 0x0C18 is a C1.
|
|
*/
|
|
|
|
static inline uint32_t olpc_board(uint8_t id)
|
|
{
|
|
return (id << 4) | 0x8;
|
|
}
|
|
|
|
static inline uint32_t olpc_board_pre(uint8_t id)
|
|
{
|
|
return id << 4;
|
|
}
|
|
|
|
static inline int machine_is_olpc(void)
|
|
{
|
|
return (olpc_platform_info.flags & OLPC_F_PRESENT) ? 1 : 0;
|
|
}
|
|
|
|
/*
|
|
* The DCON is OLPC's Display Controller. It has a number of unique
|
|
* features that we might want to take advantage of..
|
|
*/
|
|
static inline int olpc_has_dcon(void)
|
|
{
|
|
return (olpc_platform_info.flags & OLPC_F_DCON) ? 1 : 0;
|
|
}
|
|
|
|
/*
|
|
* The "Mass Production" version of OLPC's XO is identified as being model
|
|
* C2. During the prototype phase, the following models (in chronological
|
|
* order) were created: A1, B1, B2, B3, B4, C1. The A1 through B2 models
|
|
* were based on Geode GX CPUs, and models after that were based upon
|
|
* Geode LX CPUs. There were also some hand-assembled models floating
|
|
* around, referred to as PreB1, PreB2, etc.
|
|
*/
|
|
static inline int olpc_board_at_least(uint32_t rev)
|
|
{
|
|
return olpc_platform_info.boardrev >= rev;
|
|
}
|
|
|
|
#else
|
|
|
|
static inline int machine_is_olpc(void)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
static inline int olpc_has_dcon(void)
|
|
{
|
|
return 0;
|
|
}
|
|
|
|
#endif
|
|
|
|
extern int pci_olpc_init(void);
|
|
|
|
/* EC related functions */
|
|
|
|
extern int olpc_ec_cmd(unsigned char cmd, unsigned char *inbuf, size_t inlen,
|
|
unsigned char *outbuf, size_t outlen);
|
|
|
|
extern int olpc_ec_mask_set(uint8_t bits);
|
|
extern int olpc_ec_mask_unset(uint8_t bits);
|
|
|
|
/* EC commands */
|
|
|
|
#define EC_FIRMWARE_REV 0x08
|
|
#define EC_WLAN_ENTER_RESET 0x35
|
|
#define EC_WLAN_LEAVE_RESET 0x25
|
|
|
|
/* SCI source values */
|
|
|
|
#define EC_SCI_SRC_EMPTY 0x00
|
|
#define EC_SCI_SRC_GAME 0x01
|
|
#define EC_SCI_SRC_BATTERY 0x02
|
|
#define EC_SCI_SRC_BATSOC 0x04
|
|
#define EC_SCI_SRC_BATERR 0x08
|
|
#define EC_SCI_SRC_EBOOK 0x10
|
|
#define EC_SCI_SRC_WLAN 0x20
|
|
#define EC_SCI_SRC_ACPWR 0x40
|
|
#define EC_SCI_SRC_ALL 0x7F
|
|
|
|
/* GPIO assignments */
|
|
|
|
#define OLPC_GPIO_MIC_AC 1
|
|
#define OLPC_GPIO_DCON_STAT0 5
|
|
#define OLPC_GPIO_DCON_STAT1 6
|
|
#define OLPC_GPIO_DCON_IRQ 7
|
|
#define OLPC_GPIO_THRM_ALRM geode_gpio(10)
|
|
#define OLPC_GPIO_DCON_LOAD 11
|
|
#define OLPC_GPIO_DCON_BLANK 12
|
|
#define OLPC_GPIO_SMB_CLK 14
|
|
#define OLPC_GPIO_SMB_DATA 15
|
|
#define OLPC_GPIO_WORKAUX geode_gpio(24)
|
|
#define OLPC_GPIO_LID geode_gpio(26)
|
|
#define OLPC_GPIO_ECSCI geode_gpio(27)
|
|
|
|
#endif /* _ASM_X86_OLPC_H */
|