kevin/linux
1
Fork 0
Code
8b9cb3a8f3
linux/arch/arm/mach-omap2/control.c
Paul Walmsley 596efe4792 OMAP3: control/PM: move padconf save code to mach-omap2/control.c 
Move the padconf save code from pm34xx.c to the System Control Module
code in mach-omap2/control.c.  This is part of the general push to
move direct register access from middle-layer core code to low-level
core code, so the middle-layer code can be abstracted to work on
multiple platforms and cleaned up.

In the medium-to-long term, this code should be called by the mux
layer code, not the PM idle code.  This is because, according to the
TRM, saving the padconf only needs to be done when the padconf
changes[1].

Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Tony Lindgren <tony@atomide.com>
Tested-by: Rajendra Nayak <rnayak@ti.com>
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>

1. OMAP34xx Multimedia Device Silicon Revision 3.1.x [Rev. ZH] [SWPU222H]
   Section 4.11.4 "Device Off-Mode Sequences"
2010-12-21 21:05:16 -07:00

565 lines
18 KiB
C
Raw Blame History

/*
* OMAP2/3 System Control Module register access
*
* Copyright (C) 2007 Texas Instruments, Inc.
* Copyright (C) 2007 Nokia Corporation
*
* Written by Paul Walmsley
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#undef DEBUG
#include <linux/kernel.h>
#include <linux/io.h>
#include <plat/common.h>
#include <plat/sdrc.h>
#include "cm-regbits-34xx.h"
#include "prm-regbits-34xx.h"
#include "prm2xxx_3xxx.h"
#include "cm2xxx_3xxx.h"
#include "sdrc.h"
#include "pm.h"
#include "control.h"
/* Used by omap3_ctrl_save_padconf() */
#define START_PADCONF_SAVE 0x2
#define PADCONF_SAVE_DONE 0x1
static void __iomem *omap2_ctrl_base;
static void __iomem *omap4_ctrl_pad_base;
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
struct omap3_scratchpad {
u32 boot_config_ptr;
u32 public_restore_ptr;
u32 secure_ram_restore_ptr;
u32 sdrc_module_semaphore;
u32 prcm_block_offset;
u32 sdrc_block_offset;
};
struct omap3_scratchpad_prcm_block {
u32 prm_clksrc_ctrl;
u32 prm_clksel;
u32 cm_clksel_core;
u32 cm_clksel_wkup;
u32 cm_clken_pll;
u32 cm_autoidle_pll;
u32 cm_clksel1_pll;
u32 cm_clksel2_pll;
u32 cm_clksel3_pll;
u32 cm_clken_pll_mpu;
u32 cm_autoidle_pll_mpu;
u32 cm_clksel1_pll_mpu;
u32 cm_clksel2_pll_mpu;
u32 prcm_block_size;
};
struct omap3_scratchpad_sdrc_block {
u16 sysconfig;
u16 cs_cfg;
u16 sharing;
u16 err_type;
u32 dll_a_ctrl;
u32 dll_b_ctrl;
u32 power;
u32 cs_0;
u32 mcfg_0;
u16 mr_0;
u16 emr_1_0;
u16 emr_2_0;
u16 emr_3_0;
u32 actim_ctrla_0;
u32 actim_ctrlb_0;
u32 rfr_ctrl_0;
u32 cs_1;
u32 mcfg_1;
u16 mr_1;
u16 emr_1_1;
u16 emr_2_1;
u16 emr_3_1;
u32 actim_ctrla_1;
u32 actim_ctrlb_1;
u32 rfr_ctrl_1;
u16 dcdl_1_ctrl;
u16 dcdl_2_ctrl;
u32 flags;
u32 block_size;
};
void *omap3_secure_ram_storage;
/*
* This is used to store ARM registers in SDRAM before attempting
* an MPU OFF. The save and restore happens from the SRAM sleep code.
* The address is stored in scratchpad, so that it can be used
* during the restore path.
*/
u32 omap3_arm_context[128];
struct omap3_control_regs {
u32 sysconfig;
u32 devconf0;
u32 mem_dftrw0;
u32 mem_dftrw1;
u32 msuspendmux_0;
u32 msuspendmux_1;
u32 msuspendmux_2;
u32 msuspendmux_3;
u32 msuspendmux_4;
u32 msuspendmux_5;
u32 sec_ctrl;
u32 devconf1;
u32 csirxfe;
u32 iva2_bootaddr;
u32 iva2_bootmod;
u32 debobs_0;
u32 debobs_1;
u32 debobs_2;
u32 debobs_3;
u32 debobs_4;
u32 debobs_5;
u32 debobs_6;
u32 debobs_7;
u32 debobs_8;
u32 prog_io0;
u32 prog_io1;
u32 dss_dpll_spreading;
u32 core_dpll_spreading;
u32 per_dpll_spreading;
u32 usbhost_dpll_spreading;
u32 pbias_lite;
u32 temp_sensor;
u32 sramldo4;
u32 sramldo5;
u32 csi;
u32 padconf_sys_nirq;
};
static struct omap3_control_regs control_context;
#endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */
#define OMAP_CTRL_REGADDR(reg) (omap2_ctrl_base + (reg))
#define OMAP4_CTRL_PAD_REGADDR(reg) (omap4_ctrl_pad_base + (reg))
void __init omap2_set_globals_control(struct omap_globals *omap2_globals)
{
/* Static mapping, never released */
if (omap2_globals->ctrl) {
omap2_ctrl_base = ioremap(omap2_globals->ctrl, SZ_4K);
WARN_ON(!omap2_ctrl_base);
}
/* Static mapping, never released */
if (omap2_globals->ctrl_pad) {
omap4_ctrl_pad_base = ioremap(omap2_globals->ctrl_pad, SZ_4K);
WARN_ON(!omap4_ctrl_pad_base);
}
}
void __iomem *omap_ctrl_base_get(void)
{
return omap2_ctrl_base;
}
u8 omap_ctrl_readb(u16 offset)
{
return __raw_readb(OMAP_CTRL_REGADDR(offset));
}
u16 omap_ctrl_readw(u16 offset)
{
return __raw_readw(OMAP_CTRL_REGADDR(offset));
}
u32 omap_ctrl_readl(u16 offset)
{
return __raw_readl(OMAP_CTRL_REGADDR(offset));
}
void omap_ctrl_writeb(u8 val, u16 offset)
{
__raw_writeb(val, OMAP_CTRL_REGADDR(offset));
}
void omap_ctrl_writew(u16 val, u16 offset)
{
__raw_writew(val, OMAP_CTRL_REGADDR(offset));
}
void omap_ctrl_writel(u32 val, u16 offset)
{
__raw_writel(val, OMAP_CTRL_REGADDR(offset));
}
/*
* On OMAP4 control pad are not addressable from control
* core base. So the common omap_ctrl_read/write APIs breaks
* Hence export separate APIs to manage the omap4 pad control
* registers. This APIs will work only for OMAP4
*/
u32 omap4_ctrl_pad_readl(u16 offset)
{
return __raw_readl(OMAP4_CTRL_PAD_REGADDR(offset));
}
void omap4_ctrl_pad_writel(u32 val, u16 offset)
{
__raw_writel(val, OMAP4_CTRL_PAD_REGADDR(offset));
}
#ifdef CONFIG_ARCH_OMAP3
/**
* omap3_ctrl_write_boot_mode - set scratchpad boot mode for the next boot
* @bootmode: 8-bit value to pass to some boot code
*
* Set the bootmode in the scratchpad RAM. This is used after the
* system restarts. Not sure what actually uses this - it may be the
* bootloader, rather than the boot ROM - contrary to the preserved
* comment below. No return value.
*/
void omap3_ctrl_write_boot_mode(u8 bootmode)
{
u32 l;
l = ('B' << 24) | ('M' << 16) | bootmode;
/*
* Reserve the first word in scratchpad for communicating
* with the boot ROM. A pointer to a data structure
* describing the boot process can be stored there,
* cf. OMAP34xx TRM, Initialization / Software Booting
* Configuration.
*
* XXX This should use some omap_ctrl_writel()-type function
*/
__raw_writel(l, OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD + 4));
}
#endif
#if defined(CONFIG_ARCH_OMAP3) && defined(CONFIG_PM)
/*
* Clears the scratchpad contents in case of cold boot-
* called during bootup
*/
void omap3_clear_scratchpad_contents(void)
{
u32 max_offset = OMAP343X_SCRATCHPAD_ROM_OFFSET;
void __iomem *v_addr;
u32 offset = 0;
v_addr = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD_ROM);
if (omap2_prm_read_mod_reg(OMAP3430_GR_MOD, OMAP3_PRM_RSTST_OFFSET) &
OMAP3430_GLOBAL_COLD_RST_MASK) {
for ( ; offset <= max_offset; offset += 0x4)
__raw_writel(0x0, (v_addr + offset));
omap2_prm_set_mod_reg_bits(OMAP3430_GLOBAL_COLD_RST_MASK,
OMAP3430_GR_MOD,
OMAP3_PRM_RSTST_OFFSET);
}
}
/* Populate the scratchpad structure with restore structure */
void omap3_save_scratchpad_contents(void)
{
void __iomem *scratchpad_address;
u32 arm_context_addr;
struct omap3_scratchpad scratchpad_contents;
struct omap3_scratchpad_prcm_block prcm_block_contents;
struct omap3_scratchpad_sdrc_block sdrc_block_contents;
/*
* Populate the Scratchpad contents
*
* The "get_*restore_pointer" functions are used to provide a
* physical restore address where the ROM code jumps while waking
* up from MPU OFF/OSWR state.
* The restore pointer is stored into the scratchpad.
*/
scratchpad_contents.boot_config_ptr = 0x0;
if (cpu_is_omap3630())
scratchpad_contents.public_restore_ptr =
virt_to_phys(get_omap3630_restore_pointer());
else if (omap_rev() != OMAP3430_REV_ES3_0 &&
omap_rev() != OMAP3430_REV_ES3_1)
scratchpad_contents.public_restore_ptr =
virt_to_phys(get_restore_pointer());
else
scratchpad_contents.public_restore_ptr =
virt_to_phys(get_es3_restore_pointer());
if (omap_type() == OMAP2_DEVICE_TYPE_GP)
scratchpad_contents.secure_ram_restore_ptr = 0x0;
else
scratchpad_contents.secure_ram_restore_ptr =
(u32) __pa(omap3_secure_ram_storage);
scratchpad_contents.sdrc_module_semaphore = 0x0;
scratchpad_contents.prcm_block_offset = 0x2C;
scratchpad_contents.sdrc_block_offset = 0x64;
/* Populate the PRCM block contents */
prcm_block_contents.prm_clksrc_ctrl =
omap2_prm_read_mod_reg(OMAP3430_GR_MOD,
OMAP3_PRM_CLKSRC_CTRL_OFFSET);
prcm_block_contents.prm_clksel =
omap2_prm_read_mod_reg(OMAP3430_CCR_MOD,
OMAP3_PRM_CLKSEL_OFFSET);
prcm_block_contents.cm_clksel_core =
omap2_cm_read_mod_reg(CORE_MOD, CM_CLKSEL);
prcm_block_contents.cm_clksel_wkup =
omap2_cm_read_mod_reg(WKUP_MOD, CM_CLKSEL);
prcm_block_contents.cm_clken_pll =
omap2_cm_read_mod_reg(PLL_MOD, CM_CLKEN);
prcm_block_contents.cm_autoidle_pll =
omap2_cm_read_mod_reg(PLL_MOD, OMAP3430_CM_AUTOIDLE_PLL);
prcm_block_contents.cm_clksel1_pll =
omap2_cm_read_mod_reg(PLL_MOD, OMAP3430_CM_CLKSEL1_PLL);
prcm_block_contents.cm_clksel2_pll =
omap2_cm_read_mod_reg(PLL_MOD, OMAP3430_CM_CLKSEL2_PLL);
prcm_block_contents.cm_clksel3_pll =
omap2_cm_read_mod_reg(PLL_MOD, OMAP3430_CM_CLKSEL3);
prcm_block_contents.cm_clken_pll_mpu =
omap2_cm_read_mod_reg(MPU_MOD, OMAP3430_CM_CLKEN_PLL);
prcm_block_contents.cm_autoidle_pll_mpu =
omap2_cm_read_mod_reg(MPU_MOD, OMAP3430_CM_AUTOIDLE_PLL);
prcm_block_contents.cm_clksel1_pll_mpu =
omap2_cm_read_mod_reg(MPU_MOD, OMAP3430_CM_CLKSEL1_PLL);
prcm_block_contents.cm_clksel2_pll_mpu =
omap2_cm_read_mod_reg(MPU_MOD, OMAP3430_CM_CLKSEL2_PLL);
prcm_block_contents.prcm_block_size = 0x0;
/* Populate the SDRC block contents */
sdrc_block_contents.sysconfig =
(sdrc_read_reg(SDRC_SYSCONFIG) & 0xFFFF);
sdrc_block_contents.cs_cfg =
(sdrc_read_reg(SDRC_CS_CFG) & 0xFFFF);
sdrc_block_contents.sharing =
(sdrc_read_reg(SDRC_SHARING) & 0xFFFF);
sdrc_block_contents.err_type =
(sdrc_read_reg(SDRC_ERR_TYPE) & 0xFFFF);
sdrc_block_contents.dll_a_ctrl = sdrc_read_reg(SDRC_DLLA_CTRL);
sdrc_block_contents.dll_b_ctrl = 0x0;
/*
* Due to a OMAP3 errata (1.142), on EMU/HS devices SRDC should
* be programed to issue automatic self refresh on timeout
* of AUTO_CNT = 1 prior to any transition to OFF mode.
*/
if ((omap_type() != OMAP2_DEVICE_TYPE_GP)
&& (omap_rev() >= OMAP3430_REV_ES3_0))
sdrc_block_contents.power = (sdrc_read_reg(SDRC_POWER) &
~(SDRC_POWER_AUTOCOUNT_MASK|
SDRC_POWER_CLKCTRL_MASK)) |
(1 << SDRC_POWER_AUTOCOUNT_SHIFT) |
SDRC_SELF_REFRESH_ON_AUTOCOUNT;
else
sdrc_block_contents.power = sdrc_read_reg(SDRC_POWER);
sdrc_block_contents.cs_0 = 0x0;
sdrc_block_contents.mcfg_0 = sdrc_read_reg(SDRC_MCFG_0);
sdrc_block_contents.mr_0 = (sdrc_read_reg(SDRC_MR_0) & 0xFFFF);
sdrc_block_contents.emr_1_0 = 0x0;
sdrc_block_contents.emr_2_0 = 0x0;
sdrc_block_contents.emr_3_0 = 0x0;
sdrc_block_contents.actim_ctrla_0 =
sdrc_read_reg(SDRC_ACTIM_CTRL_A_0);
sdrc_block_contents.actim_ctrlb_0 =
sdrc_read_reg(SDRC_ACTIM_CTRL_B_0);
sdrc_block_contents.rfr_ctrl_0 =
sdrc_read_reg(SDRC_RFR_CTRL_0);
sdrc_block_contents.cs_1 = 0x0;
sdrc_block_contents.mcfg_1 = sdrc_read_reg(SDRC_MCFG_1);
sdrc_block_contents.mr_1 = sdrc_read_reg(SDRC_MR_1) & 0xFFFF;
sdrc_block_contents.emr_1_1 = 0x0;
sdrc_block_contents.emr_2_1 = 0x0;
sdrc_block_contents.emr_3_1 = 0x0;
sdrc_block_contents.actim_ctrla_1 =
sdrc_read_reg(SDRC_ACTIM_CTRL_A_1);
sdrc_block_contents.actim_ctrlb_1 =
sdrc_read_reg(SDRC_ACTIM_CTRL_B_1);
sdrc_block_contents.rfr_ctrl_1 =
sdrc_read_reg(SDRC_RFR_CTRL_1);
sdrc_block_contents.dcdl_1_ctrl = 0x0;
sdrc_block_contents.dcdl_2_ctrl = 0x0;
sdrc_block_contents.flags = 0x0;
sdrc_block_contents.block_size = 0x0;
arm_context_addr = virt_to_phys(omap3_arm_context);
/* Copy all the contents to the scratchpad location */
scratchpad_address = OMAP2_L4_IO_ADDRESS(OMAP343X_SCRATCHPAD);
memcpy_toio(scratchpad_address, &scratchpad_contents,
sizeof(scratchpad_contents));
/* Scratchpad contents being 32 bits, a divide by 4 done here */
memcpy_toio(scratchpad_address +
scratchpad_contents.prcm_block_offset,
&prcm_block_contents, sizeof(prcm_block_contents));
memcpy_toio(scratchpad_address +
scratchpad_contents.sdrc_block_offset,
&sdrc_block_contents, sizeof(sdrc_block_contents));
/*
* Copies the address of the location in SDRAM where ARM
* registers get saved during a MPU OFF transition.
*/
memcpy_toio(scratchpad_address +
scratchpad_contents.sdrc_block_offset +
sizeof(sdrc_block_contents), &arm_context_addr, 4);
}
void omap3_control_save_context(void)
{
control_context.sysconfig = omap_ctrl_readl(OMAP2_CONTROL_SYSCONFIG);
control_context.devconf0 = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
control_context.mem_dftrw0 =
omap_ctrl_readl(OMAP343X_CONTROL_MEM_DFTRW0);
control_context.mem_dftrw1 =
omap_ctrl_readl(OMAP343X_CONTROL_MEM_DFTRW1);
control_context.msuspendmux_0 =
omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_0);
control_context.msuspendmux_1 =
omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_1);
control_context.msuspendmux_2 =
omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_2);
control_context.msuspendmux_3 =
omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_3);
control_context.msuspendmux_4 =
omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_4);
control_context.msuspendmux_5 =
omap_ctrl_readl(OMAP2_CONTROL_MSUSPENDMUX_5);
control_context.sec_ctrl = omap_ctrl_readl(OMAP2_CONTROL_SEC_CTRL);
control_context.devconf1 = omap_ctrl_readl(OMAP343X_CONTROL_DEVCONF1);
control_context.csirxfe = omap_ctrl_readl(OMAP343X_CONTROL_CSIRXFE);
control_context.iva2_bootaddr =
omap_ctrl_readl(OMAP343X_CONTROL_IVA2_BOOTADDR);
control_context.iva2_bootmod =
omap_ctrl_readl(OMAP343X_CONTROL_IVA2_BOOTMOD);
control_context.debobs_0 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(0));
control_context.debobs_1 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(1));
control_context.debobs_2 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(2));
control_context.debobs_3 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(3));
control_context.debobs_4 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(4));
control_context.debobs_5 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(5));
control_context.debobs_6 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(6));
control_context.debobs_7 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(7));
control_context.debobs_8 = omap_ctrl_readl(OMAP343X_CONTROL_DEBOBS(8));
control_context.prog_io0 = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO0);
control_context.prog_io1 = omap_ctrl_readl(OMAP343X_CONTROL_PROG_IO1);
control_context.dss_dpll_spreading =
omap_ctrl_readl(OMAP343X_CONTROL_DSS_DPLL_SPREADING);
control_context.core_dpll_spreading =
omap_ctrl_readl(OMAP343X_CONTROL_CORE_DPLL_SPREADING);
control_context.per_dpll_spreading =
omap_ctrl_readl(OMAP343X_CONTROL_PER_DPLL_SPREADING);
control_context.usbhost_dpll_spreading =
omap_ctrl_readl(OMAP343X_CONTROL_USBHOST_DPLL_SPREADING);
control_context.pbias_lite =
omap_ctrl_readl(OMAP343X_CONTROL_PBIAS_LITE);
control_context.temp_sensor =
omap_ctrl_readl(OMAP343X_CONTROL_TEMP_SENSOR);
control_context.sramldo4 = omap_ctrl_readl(OMAP343X_CONTROL_SRAMLDO4);
control_context.sramldo5 = omap_ctrl_readl(OMAP343X_CONTROL_SRAMLDO5);
control_context.csi = omap_ctrl_readl(OMAP343X_CONTROL_CSI);
control_context.padconf_sys_nirq =
omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_SYSNIRQ);
return;
}
void omap3_control_restore_context(void)
{
omap_ctrl_writel(control_context.sysconfig, OMAP2_CONTROL_SYSCONFIG);
omap_ctrl_writel(control_context.devconf0, OMAP2_CONTROL_DEVCONF0);
omap_ctrl_writel(control_context.mem_dftrw0,
OMAP343X_CONTROL_MEM_DFTRW0);
omap_ctrl_writel(control_context.mem_dftrw1,
OMAP343X_CONTROL_MEM_DFTRW1);
omap_ctrl_writel(control_context.msuspendmux_0,
OMAP2_CONTROL_MSUSPENDMUX_0);
omap_ctrl_writel(control_context.msuspendmux_1,
OMAP2_CONTROL_MSUSPENDMUX_1);
omap_ctrl_writel(control_context.msuspendmux_2,
OMAP2_CONTROL_MSUSPENDMUX_2);
omap_ctrl_writel(control_context.msuspendmux_3,
OMAP2_CONTROL_MSUSPENDMUX_3);
omap_ctrl_writel(control_context.msuspendmux_4,
OMAP2_CONTROL_MSUSPENDMUX_4);
omap_ctrl_writel(control_context.msuspendmux_5,
OMAP2_CONTROL_MSUSPENDMUX_5);
omap_ctrl_writel(control_context.sec_ctrl, OMAP2_CONTROL_SEC_CTRL);
omap_ctrl_writel(control_context.devconf1, OMAP343X_CONTROL_DEVCONF1);
omap_ctrl_writel(control_context.csirxfe, OMAP343X_CONTROL_CSIRXFE);
omap_ctrl_writel(control_context.iva2_bootaddr,
OMAP343X_CONTROL_IVA2_BOOTADDR);
omap_ctrl_writel(control_context.iva2_bootmod,
OMAP343X_CONTROL_IVA2_BOOTMOD);
omap_ctrl_writel(control_context.debobs_0, OMAP343X_CONTROL_DEBOBS(0));
omap_ctrl_writel(control_context.debobs_1, OMAP343X_CONTROL_DEBOBS(1));
omap_ctrl_writel(control_context.debobs_2, OMAP343X_CONTROL_DEBOBS(2));
omap_ctrl_writel(control_context.debobs_3, OMAP343X_CONTROL_DEBOBS(3));
omap_ctrl_writel(control_context.debobs_4, OMAP343X_CONTROL_DEBOBS(4));
omap_ctrl_writel(control_context.debobs_5, OMAP343X_CONTROL_DEBOBS(5));
omap_ctrl_writel(control_context.debobs_6, OMAP343X_CONTROL_DEBOBS(6));
omap_ctrl_writel(control_context.debobs_7, OMAP343X_CONTROL_DEBOBS(7));
omap_ctrl_writel(control_context.debobs_8, OMAP343X_CONTROL_DEBOBS(8));
omap_ctrl_writel(control_context.prog_io0, OMAP343X_CONTROL_PROG_IO0);
omap_ctrl_writel(control_context.prog_io1, OMAP343X_CONTROL_PROG_IO1);
omap_ctrl_writel(control_context.dss_dpll_spreading,
OMAP343X_CONTROL_DSS_DPLL_SPREADING);
omap_ctrl_writel(control_context.core_dpll_spreading,
OMAP343X_CONTROL_CORE_DPLL_SPREADING);
omap_ctrl_writel(control_context.per_dpll_spreading,
OMAP343X_CONTROL_PER_DPLL_SPREADING);
omap_ctrl_writel(control_context.usbhost_dpll_spreading,
OMAP343X_CONTROL_USBHOST_DPLL_SPREADING);
omap_ctrl_writel(control_context.pbias_lite,
OMAP343X_CONTROL_PBIAS_LITE);
omap_ctrl_writel(control_context.temp_sensor,
OMAP343X_CONTROL_TEMP_SENSOR);
omap_ctrl_writel(control_context.sramldo4, OMAP343X_CONTROL_SRAMLDO4);
omap_ctrl_writel(control_context.sramldo5, OMAP343X_CONTROL_SRAMLDO5);
omap_ctrl_writel(control_context.csi, OMAP343X_CONTROL_CSI);
omap_ctrl_writel(control_context.padconf_sys_nirq,
OMAP343X_CONTROL_PADCONF_SYSNIRQ);
return;
}
void omap3630_ctrl_disable_rta(void)
{
if (!cpu_is_omap3630())
return;
omap_ctrl_writel(OMAP36XX_RTA_DISABLE, OMAP36XX_CONTROL_MEM_RTA_CTRL);
}
/**
* omap3_ctrl_save_padconf - save padconf registers to scratchpad RAM
*
* Tell the SCM to start saving the padconf registers, then wait for
* the process to complete. Returns 0 unconditionally, although it
* should also eventually be able to return -ETIMEDOUT, if the save
* does not complete.
*
* XXX This function is missing a timeout. What should it be?
*/
int omap3_ctrl_save_padconf(void)
{
u32 cpo;
/* Save the padconf registers */
cpo = omap_ctrl_readl(OMAP343X_CONTROL_PADCONF_OFF);
cpo |= START_PADCONF_SAVE;
omap_ctrl_writel(cpo, OMAP343X_CONTROL_PADCONF_OFF);
/* wait for the save to complete */
while (!(omap_ctrl_readl(OMAP343X_CONTROL_GENERAL_PURPOSE_STATUS)
& PADCONF_SAVE_DONE))
udelay(1);
return 0;
}
#endif /* CONFIG_ARCH_OMAP3 && CONFIG_PM */
View Git Blame Copy Permalink