eb83092c2b
AM35x has musb interface and uses CPPI4.1 DMA engine.
Current patch supports only PIO mode. DMA support can be
added later once basic CPPI4.1 DMA patch is accepted.
Also added USB_MUSB_AM35X which is required to differentiate musb ips
between OMAP3x and AM35x. This config would be used to for below
purposes,
- Select am35x.c instead of omap2430.c for compilation
at drivers/usb/musb directory. Please note there are
significant differneces in these two files as musb ip
in quite different on AM35x.
Please note that in multi omap configuration only omap2430.c
file will get compiled and we would require to select only
AM35x based board config to compile am35x.c
- Select workaround codes applicable for AM35x musb issues.
one such workaround is for bytewise read issue on AM35x.
Signed-off-by: Ajay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
49 lines
1.3 KiB
Makefile
49 lines
1.3 KiB
Makefile
#
|
|
# for USB OTG silicon based on Mentor Graphics INVENTRA designs
|
|
#
|
|
|
|
ccflags-$(CONFIG_USB_MUSB_DEBUG) := -DDEBUG
|
|
|
|
obj-$(CONFIG_USB_MUSB_HDRC) += musb_hdrc.o
|
|
|
|
musb_hdrc-y := musb_core.o
|
|
|
|
musb_hdrc-$(CONFIG_ARCH_DAVINCI_DMx) += davinci.o
|
|
musb_hdrc-$(CONFIG_ARCH_DAVINCI_DA8XX) += da8xx.o
|
|
musb_hdrc-$(CONFIG_USB_TUSB6010) += tusb6010.o
|
|
musb_hdrc-$(CONFIG_ARCH_OMAP2430) += omap2430.o
|
|
ifeq ($(CONFIG_USB_MUSB_AM35X),y)
|
|
musb_hdrc-$(CONFIG_ARCH_OMAP3430) += am35x.o
|
|
else
|
|
musb_hdrc-$(CONFIG_ARCH_OMAP3430) += omap2430.o
|
|
endif
|
|
musb_hdrc-$(CONFIG_ARCH_OMAP4) += omap2430.o
|
|
musb_hdrc-$(CONFIG_BF54x) += blackfin.o
|
|
musb_hdrc-$(CONFIG_BF52x) += blackfin.o
|
|
musb_hdrc-$(CONFIG_USB_GADGET_MUSB_HDRC) += musb_gadget_ep0.o musb_gadget.o
|
|
musb_hdrc-$(CONFIG_USB_MUSB_HDRC_HCD) += musb_virthub.o musb_host.o
|
|
musb_hdrc-$(CONFIG_DEBUG_FS) += musb_debugfs.o
|
|
|
|
# the kconfig must guarantee that only one of the
|
|
# possible I/O schemes will be enabled at a time ...
|
|
# PIO only, or DMA (several potential schemes).
|
|
# though PIO is always there to back up DMA, and for ep0
|
|
|
|
ifneq ($(CONFIG_MUSB_PIO_ONLY),y)
|
|
|
|
ifeq ($(CONFIG_USB_INVENTRA_DMA),y)
|
|
musb_hdrc-y += musbhsdma.o
|
|
|
|
else
|
|
ifeq ($(CONFIG_USB_TI_CPPI_DMA),y)
|
|
musb_hdrc-y += cppi_dma.o
|
|
|
|
else
|
|
ifeq ($(CONFIG_USB_TUSB_OMAP_DMA),y)
|
|
musb_hdrc-y += tusb6010_omap.o
|
|
|
|
endif
|
|
endif
|
|
endif
|
|
endif
|