Nicolas Pitre 639da5ee37 ARM: add an extra temp register to the low level debugging addruart macro ... Some platforms (like OMAP not to name it) are doing rather complicated hacks just to determine the base UART address to use. Let's give their addruart macro some slack by providing an extra work register which will allow for much needed cleanups. This is basically a no-op as this commit is only adding the extra argument to the macro but no one is using it yet. Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org> Reviewed-by: Kevin Hilman <khilman@ti.com>		2011-09-26 10:11:25 -04:00
..
include/mach	ARM: add an extra temp register to the low level debugging addruart macro	2011-09-26 10:11:25 -04:00
board-mop500-pins.c	Merge branches 'cns3xxx/devel', 'davinci/devel', 'imx/devel', 'lpc32xx/devel', 'pxa/devel', 'tegra/devel' and 'stericsson/master' of git+ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc into next/devel	2011-07-17 21:31:38 +02:00
board-mop500-regulators.c	Merge branch 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc	2011-07-26 17:41:04 -07:00
board-mop500-regulators.h	mach-ux500: configure board for the TPS61052 regulator v2	2011-03-28 08:54:23 +02:00
board-mop500-sdi.c	mach-ux500: Add SDI support for snowball board	2011-06-23 12:04:56 +02:00
board-mop500-stuib.c	mach-ux500: basic HREFv60 support v2	2011-03-14 14:05:16 +01:00
board-mop500-u8500uib.c	staging: ste_rmi4: remove cross-dependent platform data	2011-07-05 20:29:16 -07:00
board-mop500-uib.c	mach-x500: fix SECTION warnings in uib	2011-06-22 13:26:49 +02:00
board-mop500.c	ARM: mach-ux500: convert boot-params to atag_offset	2011-08-21 17:15:18 -04:00
board-mop500.h	mach-ux500: Add SDI support for snowball board	2011-06-23 12:04:56 +02:00
board-u5500-sdi.c	mach-ux500: config Ux500 PL011 PL022 PL180 for DMA	2011-03-14 14:05:14 +01:00
board-u5500.c	ARM: mach-ux500: convert boot-params to atag_offset	2011-08-21 17:15:18 -04:00
clock.c	Merge branch 'next/devel' of ssh://master.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc	2011-07-26 17:41:04 -07:00
clock.h
cpu-db5500.c	mach-ux500: iomap PRCMU TCDM memory	2011-06-21 10:57:42 +02:00
cpu-db8500.c	gpio/nomadik: fix sleepmode for elder Nomadik	2011-06-09 15:03:38 -06:00
cpu.c	mfd: add DB5500 PRCMU driver	2011-05-24 22:19:37 +02:00
devices-common.c	plat-nomadik: support varying number of GPIOs per block	2011-03-14 14:05:14 +01:00
devices-common.h	ARM: 6830/1: mach-ux500: force PrimeCell revisions	2011-05-26 10:33:35 +01:00
devices-db5500.h	ARM: 6830/1: mach-ux500: force PrimeCell revisions	2011-05-26 10:33:35 +01:00
devices-db8500.c	mach-ux500: config Ux500 PL011 PL022 PL180 for DMA	2011-03-14 14:05:14 +01:00
devices-db8500.h	ARM: 6830/1: mach-ux500: force PrimeCell revisions	2011-05-26 10:33:35 +01:00
devices.c
dma-db5500.c	mach-ux500: add MUSB to db5500 devices	2011-03-14 14:05:12 +01:00
headsmp.S
hotplug.c
id.c
Kconfig	mach-ux500: Kconfig for snowball board	2011-06-23 12:04:56 +02:00
localtimer.c
Makefile	mfd: update DB8500 PRCMU driver	2011-05-24 22:18:57 +02:00
Makefile.boot
mbox-db5500.c	treewide: Fix iomap resource size miscalculations	2011-04-10 17:01:04 +02:00
modem-irq-db5500.c	arm: Fold irq_set_chip/irq_set_handler	2011-03-29 14:47:58 +02:00
pins-db5500.h
pins-db8500.h
platsmp.c	ARM: 6993/1: platsmp: Allow secondary cpu hotplug with maxcpus=1	2011-07-07 14:45:07 +01:00
ste-dma40-db5500.h
ste-dma40-db8500.h
usb.c	mach-ux500: fix USB build error	2011-06-27 19:45:40 +02:00