d7304dee3b
Add a tuner config parameter for TDA9887, default_pll_gating_18, that changes the L standard PLL gating value from 36% to 0% (datasheet says 0%, tda9887 code says 18%). Turn this on for Microtune 4049FM5, as recomended by tuner datasheet. Signed-off-by: Trent Piepho <xyzzy@speakeasy.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
115 lines
4.1 KiB
C
115 lines
4.1 KiB
C
/*
|
|
* descriptions for simple tuners.
|
|
*/
|
|
|
|
#ifndef __TUNER_TYPES_H__
|
|
#define __TUNER_TYPES_H__
|
|
|
|
enum param_type {
|
|
TUNER_PARAM_TYPE_RADIO, \
|
|
TUNER_PARAM_TYPE_PAL, \
|
|
TUNER_PARAM_TYPE_SECAM, \
|
|
TUNER_PARAM_TYPE_NTSC
|
|
};
|
|
|
|
struct tuner_range {
|
|
unsigned short limit;
|
|
unsigned char config;
|
|
unsigned char cb;
|
|
};
|
|
|
|
struct tuner_params {
|
|
enum param_type type;
|
|
|
|
/* Many Philips based tuners have a comment like this in their
|
|
* datasheet:
|
|
*
|
|
* For channel selection involving band switching, and to ensure
|
|
* smooth tuning to the desired channel without causing
|
|
* unnecessary charge pump action, it is recommended to consider
|
|
* the difference between wanted channel frequency and the
|
|
* current channel frequency. Unnecessary charge pump action
|
|
* will result in very low tuning voltage which may drive the
|
|
* oscillator to extreme conditions.
|
|
*
|
|
* Set cb_first_if_lower_freq to 1, if this check is
|
|
* required for this tuner.
|
|
*
|
|
* I tested this for PAL by first setting the TV frequency to
|
|
* 203 MHz and then switching to 96.6 MHz FM radio. The result was
|
|
* static unless the control byte was sent first.
|
|
*/
|
|
unsigned int cb_first_if_lower_freq:1;
|
|
/* Set to 1 if this tuner uses a tda9887 */
|
|
unsigned int has_tda9887:1;
|
|
/* Many Philips tuners use tda9887 PORT1 to select the FM radio
|
|
sensitivity. If this setting is 1, then set PORT1 to 1 to
|
|
get proper FM reception. */
|
|
unsigned int port1_fm_high_sensitivity:1;
|
|
/* Some Philips tuners use tda9887 PORT2 to select the FM radio
|
|
sensitivity. If this setting is 1, then set PORT2 to 1 to
|
|
get proper FM reception. */
|
|
unsigned int port2_fm_high_sensitivity:1;
|
|
/* Most tuners with a tda9887 use QSS mode. Some (cheaper) tuners
|
|
use Intercarrier mode. If this setting is 1, then the tuner
|
|
needs to be set to intercarrier mode. */
|
|
unsigned int intercarrier_mode:1;
|
|
/* This setting sets the default value for PORT1.
|
|
0 means inactive, 1 means active. Note: the actual bit
|
|
value written to the tda9887 is inverted. So a 0 here
|
|
means a 1 in the B6 bit. */
|
|
unsigned int port1_active:1;
|
|
/* This setting sets the default value for PORT2.
|
|
0 means inactive, 1 means active. Note: the actual bit
|
|
value written to the tda9887 is inverted. So a 0 here
|
|
means a 1 in the B7 bit. */
|
|
unsigned int port2_active:1;
|
|
/* Sometimes PORT1 is inverted when the SECAM-L' standard is selected.
|
|
Set this bit to 1 if this is needed. */
|
|
unsigned int port1_invert_for_secam_lc:1;
|
|
/* Sometimes PORT2 is inverted when the SECAM-L' standard is selected.
|
|
Set this bit to 1 if this is needed. */
|
|
unsigned int port2_invert_for_secam_lc:1;
|
|
/* Some cards require PORT1 to be 1 for mono Radio FM and 0 for stereo. */
|
|
unsigned int port1_set_for_fm_mono:1;
|
|
/* Select 18% (or according to datasheet 0%) L standard PLL gating,
|
|
vs the driver default of 36%. */
|
|
unsigned int default_pll_gating_18:1;
|
|
/* Default tda9887 TOP value in dB for the low band. Default is 0.
|
|
Range: -16:+15 */
|
|
signed int default_top_low:5;
|
|
/* Default tda9887 TOP value in dB for the mid band. Default is 0.
|
|
Range: -16:+15 */
|
|
signed int default_top_mid:5;
|
|
/* Default tda9887 TOP value in dB for the high band. Default is 0.
|
|
Range: -16:+15 */
|
|
signed int default_top_high:5;
|
|
/* Default tda9887 TOP value in dB for SECAM-L/L' for the low band.
|
|
Default is 0. Several tuners require a different TOP value for
|
|
the SECAM-L/L' standards. Range: -16:+15 */
|
|
signed int default_top_secam_low:5;
|
|
/* Default tda9887 TOP value in dB for SECAM-L/L' for the mid band.
|
|
Default is 0. Several tuners require a different TOP value for
|
|
the SECAM-L/L' standards. Range: -16:+15 */
|
|
signed int default_top_secam_mid:5;
|
|
/* Default tda9887 TOP value in dB for SECAM-L/L' for the high band.
|
|
Default is 0. Several tuners require a different TOP value for
|
|
the SECAM-L/L' standards. Range: -16:+15 */
|
|
signed int default_top_secam_high:5;
|
|
|
|
|
|
unsigned int count;
|
|
struct tuner_range *ranges;
|
|
};
|
|
|
|
struct tunertype {
|
|
char *name;
|
|
unsigned int count;
|
|
struct tuner_params *params;
|
|
};
|
|
|
|
extern struct tunertype tuners[];
|
|
extern unsigned const int tuner_count;
|
|
|
|
#endif
|