kevin/linux
1
Fork 0
Code
594632efbb
linux/arch/arm/mach-at91/include/mach/board.h
Ryan Mallon 4037242c4f ARM: 6209/3: at91_udc: Add vbus polarity and polling mode 
Allow the vbus signal to optionally use polling. This is required if
the vbus signal is connected to an non-interrupting io expander for
example. If vbus is in polling mode, then it is assumed that the vbus
gpio may sleep. Also add an option to have vbus be an active low
signal. Both options are set in the platform data for the device.

Signed-off-by: Ryan Mallon <ryan@bluewatersys.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2010-07-18 20:39:10 +01:00

219 lines
7.1 KiB
C
Raw Blame History

/*
* arch/arm/mach-at91/include/mach/board.h
*
* Copyright (C) 2005 HP Labs
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
/*
* These are data structures found in platform_device.dev.platform_data,
* and describing board-specific data needed by drivers. For example,
* which pin is used for a given GPIO role.
*
* In 2.6, drivers should strongly avoid board-specific knowledge so
* that supporting new boards normally won't require driver patches.
* Most board-specific knowledge should be in arch/.../board-*.c files.
*/
#ifndef __ASM_ARCH_BOARD_H
#define __ASM_ARCH_BOARD_H
#include <linux/mtd/partitions.h>
#include <linux/device.h>
#include <linux/i2c.h>
#include <linux/leds.h>
#include <linux/spi/spi.h>
#include <linux/usb/atmel_usba_udc.h>
#include <linux/atmel-mci.h>
#include <sound/atmel-ac97c.h>
#include <linux/serial.h>
/* USB Device */
struct at91_udc_data {
u8 vbus_pin; /* high == host powering us */
u8 vbus_active_low; /* vbus polarity */
u8 vbus_polled; /* Use polling, not interrupt */
u8 pullup_pin; /* active == D+ pulled up */
u8 pullup_active_low; /* true == pullup_pin is active low */
};
extern void __init at91_add_device_udc(struct at91_udc_data *data);
/* USB High Speed Device */
extern void __init at91_add_device_usba(struct usba_platform_data *data);
/* Compact Flash */
struct at91_cf_data {
u8 irq_pin; /* I/O IRQ */
u8 det_pin; /* Card detect */
u8 vcc_pin; /* power switching */
u8 rst_pin; /* card reset */
u8 chipselect; /* EBI Chip Select number */
u8 flags;
#define AT91_CF_TRUE_IDE 0x01
#define AT91_IDE_SWAP_A0_A2 0x02
};
extern void __init at91_add_device_cf(struct at91_cf_data *data);
/* MMC / SD */
/* at91_mci platform config */
struct at91_mmc_data {
u8 det_pin; /* card detect IRQ */
unsigned slot_b:1; /* uses Slot B */
unsigned wire4:1; /* (SD) supports DAT0..DAT3 */
u8 wp_pin; /* (SD) writeprotect detect */
u8 vcc_pin; /* power switching (high == on) */
};
extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
/* atmel-mci platform config */
extern void __init at91_add_device_mci(short mmc_id, struct mci_platform_data *data);
/* Ethernet (EMAC & MACB) */
struct at91_eth_data {
u32 phy_mask;
u8 phy_irq_pin; /* PHY IRQ */
u8 is_rmii; /* using RMII interface? */
};
extern void __init at91_add_device_eth(struct at91_eth_data *data);
#if defined(CONFIG_ARCH_AT91SAM9260) || defined(CONFIG_ARCH_AT91SAM9263) || defined(CONFIG_ARCH_AT91SAM9G20) || defined(CONFIG_ARCH_AT91CAP9) \
|| defined(CONFIG_ARCH_AT91SAM9G45) || defined(CONFIG_ARCH_AT572D940HF)
#define eth_platform_data at91_eth_data
#endif
/* USB Host */
struct at91_usbh_data {
u8 ports; /* number of ports on root hub */
u8 vbus_pin[2]; /* port power-control pin */
};
extern void __init at91_add_device_usbh(struct at91_usbh_data *data);
extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data);
extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data);
/* NAND / SmartMedia */
struct atmel_nand_data {
u8 enable_pin; /* chip enable */
u8 det_pin; /* card detect */
u8 rdy_pin; /* ready/busy */
u8 rdy_pin_active_low; /* rdy_pin value is inverted */
u8 ale; /* address line number connected to ALE */
u8 cle; /* address line number connected to CLE */
u8 bus_width_16; /* buswidth is 16 bit */
struct mtd_partition* (*partition_info)(int, int*);
};
extern void __init at91_add_device_nand(struct atmel_nand_data *data);
/* I2C*/
#if defined(CONFIG_ARCH_AT91SAM9G45)
extern void __init at91_add_device_i2c(short i2c_id, struct i2c_board_info *devices, int nr_devices);
#else
extern void __init at91_add_device_i2c(struct i2c_board_info *devices, int nr_devices);
#endif
/* SPI */
extern void __init at91_add_device_spi(struct spi_board_info *devices, int nr_devices);
/* Serial */
#define ATMEL_UART_CTS 0x01
#define ATMEL_UART_RTS 0x02
#define ATMEL_UART_DSR 0x04
#define ATMEL_UART_DTR 0x08
#define ATMEL_UART_DCD 0x10
#define ATMEL_UART_RI 0x20
extern void __init at91_register_uart(unsigned id, unsigned portnr, unsigned pins);
extern void __init at91_set_serial_console(unsigned portnr);
struct at91_uart_config {
unsigned short console_tty; /* tty number of serial console */
unsigned short nr_tty; /* number of serial tty's */
short tty_map[]; /* map UART to tty number */
};
extern struct platform_device *atmel_default_console_device;
extern void __init __deprecated at91_init_serial(struct at91_uart_config *config);
struct atmel_uart_data {
short use_dma_tx; /* use transmit DMA? */
short use_dma_rx; /* use receive DMA? */
void __iomem *regs; /* virt. base address, if any */
struct serial_rs485 rs485; /* rs485 settings */
};
extern void __init at91_add_device_serial(void);
/*
* PWM
*/
#define AT91_PWM0 0
#define AT91_PWM1 1
#define AT91_PWM2 2
#define AT91_PWM3 3
extern void __init at91_add_device_pwm(u32 mask);
/*
* SSC -- accessed through ssc_request(id). Drivers don't bind to SSC
* platform devices. Their SSC ID is part of their configuration data,
* along with information about which SSC signals they should use.
*/
#define ATMEL_SSC_TK 0x01
#define ATMEL_SSC_TF 0x02
#define ATMEL_SSC_TD 0x04
#define ATMEL_SSC_TX (ATMEL_SSC_TK | ATMEL_SSC_TF | ATMEL_SSC_TD)
#define ATMEL_SSC_RK 0x10
#define ATMEL_SSC_RF 0x20
#define ATMEL_SSC_RD 0x40
#define ATMEL_SSC_RX (ATMEL_SSC_RK | ATMEL_SSC_RF | ATMEL_SSC_RD)
extern void __init at91_add_device_ssc(unsigned id, unsigned pins);
/* LCD Controller */
struct atmel_lcdfb_info;
extern void __init at91_add_device_lcdc(struct atmel_lcdfb_info *data);
/* AC97 */
extern void __init at91_add_device_ac97(struct ac97c_platform_data *data);
/* ISI */
extern void __init at91_add_device_isi(void);
/* Touchscreen Controller */
struct at91_tsadcc_data {
unsigned int adc_clock;
u8 pendet_debounce;
u8 ts_sample_hold_time;
};
extern void __init at91_add_device_tsadcc(struct at91_tsadcc_data *data);
/* CAN */
struct at91_can_data {
void (*transceiver_switch)(int on);
};
extern void __init at91_add_device_can(struct at91_can_data *data);
/* LEDs */
extern void __init at91_init_leds(u8 cpu_led, u8 timer_led);
extern void __init at91_gpio_leds(struct gpio_led *leds, int nr);
extern void __init at91_pwm_leds(struct gpio_led *leds, int nr);
/* AT572D940HF DSP */
extern void __init at91_add_device_mAgic(void);
/* FIXME: this needs a better location, but gets stuff building again */
extern int at91_suspend_entering_slow_clock(void);
#endif
View Git Blame Copy Permalink