kevin/linux
1
Fork 0
Code
4a05e20917
linux/drivers/ata/pata_sil680.c
Tejun Heo 1626aeb881 libata: clean up SFF init mess 
The intention of using port_mask in SFF init helpers was to eventually
support exoctic configurations such as combination of legacy and
native port on the same controller.  This never became actually
necessary and the related code always has been subtly broken one way
or the other.  Now that new init model is in place, there is no reason
to make common helpers capable of handling all corner cases.  Exotic
cases can simply dealt within LLDs as necessary.

This patch removes port_mask handling in SFF init helpers.  SFF init
helpers don't take n_ports argument and interpret it into port_mask
anymore.  All information is carried via port_info.  n_ports argument
is dropped and always two ports are allocated.  LLD can tell SFF to
skip certain port by marking it dummy.  Note that SFF code has been
treating unuvailable ports this way for a long time until recent
breakage fix from Linus and is consistent with how other drivers
handle with unavailable ports.

This fixes 1-port legacy host handling still broken after the recent
native mode fix and simplifies SFF init logic.  The following changes
are made...

* ata_pci_init_native_host() and ata_init_legacy_host() both now try
  to initialized whatever they can and mark failed ports dummy.  They
  return 0 if any port is successfully initialized.

* ata_pci_prepare_native_host() and ata_pci_init_one() now doesn't
  take n_ports argument.  All info should be specified via port_info
  array.  Always two ports are allocated.

* ata_pci_init_bmdma() exported to be used by LLDs in exotic cases.

* port_info handling in all LLDs are standardized - all port_info
  arrays are const stack variable named ppi.  Unless the second port
  is different from the first, its port_info is specified as NULL
  (tells libata that it's identical to the last non-NULL port_info).

* pata_hpt37x/hpt3x2n: don't modify static variable directly.  Make an
  on-stack copy instead as ata_piix does.

* pata_uli: It has 4 ports instead of 2.  Don't use
  ata_pci_prepare_native_host().  Allocate the host explicitly and use
  init helpers.  It's simple enough.

Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-11 18:09:18 -04:00

420 lines
11 KiB
C
Raw Blame History

/*
* pata_sil680.c - SIL680 PATA for new ATA layer
* (C) 2005 Red Hat Inc
* Alan Cox <alan@redhat.com>
*
* based upon
*
* linux/drivers/ide/pci/siimage.c Version 1.07 Nov 30, 2003
*
* Copyright (C) 2001-2002 Andre Hedrick <andre@linux-ide.org>
* Copyright (C) 2003 Red Hat <alan@redhat.com>
*
* May be copied or modified under the terms of the GNU General Public License
*
* Documentation publically available.
*
* If you have strange problems with nVidia chipset systems please
* see the SI support documentation and update your system BIOS
* if neccessary
*
* TODO
* If we know all our devices are LBA28 (or LBA28 sized) we could use
* the command fifo mode.
*/
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/blkdev.h>
#include <linux/delay.h>
#include <scsi/scsi_host.h>
#include <linux/libata.h>
#define DRV_NAME "pata_sil680"
#define DRV_VERSION "0.4.6"
/**
* sil680_selreg - return register base
* @hwif: interface
* @r: config offset
*
* Turn a config register offset into the right address in either
* PCI space or MMIO space to access the control register in question
* Thankfully this is a configuration operation so isnt performance
* criticial.
*/
static unsigned long sil680_selreg(struct ata_port *ap, int r)
{
unsigned long base = 0xA0 + r;
base += (ap->port_no << 4);
return base;
}
/**
* sil680_seldev - return register base
* @hwif: interface
* @r: config offset
*
* Turn a config register offset into the right address in either
* PCI space or MMIO space to access the control register in question
* including accounting for the unit shift.
*/
static unsigned long sil680_seldev(struct ata_port *ap, struct ata_device *adev, int r)
{
unsigned long base = 0xA0 + r;
base += (ap->port_no << 4);
base |= adev->devno ? 2 : 0;
return base;
}
/**
* sil680_cable_detect - cable detection
* @ap: ATA port
*
* Perform cable detection. The SIL680 stores this in PCI config
* space for us.
*/
static int sil680_cable_detect(struct ata_port *ap) {
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned long addr = sil680_selreg(ap, 0);
u8 ata66;
pci_read_config_byte(pdev, addr, &ata66);
if (ata66 & 1)
return ATA_CBL_PATA80;
else
return ATA_CBL_PATA40;
}
/**
* sil680_bus_reset - reset the SIL680 bus
* @ap: ATA port to reset
* @deadline: deadline jiffies for the operation
*
* Perform the SIL680 housekeeping when doing an ATA bus reset
*/
static int sil680_bus_reset(struct ata_port *ap,unsigned int *classes,
unsigned long deadline)
{
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned long addr = sil680_selreg(ap, 0);
u8 reset;
pci_read_config_byte(pdev, addr, &reset);
pci_write_config_byte(pdev, addr, reset | 0x03);
udelay(25);
pci_write_config_byte(pdev, addr, reset);
return ata_std_softreset(ap, classes, deadline);
}
static void sil680_error_handler(struct ata_port *ap)
{
ata_bmdma_drive_eh(ap, ata_std_prereset, sil680_bus_reset, NULL, ata_std_postreset);
}
/**
* sil680_set_piomode - set initial PIO mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the SIL680 registers for PIO mode. Note that the task speed
* registers are shared between the devices so we must pick the lowest
* mode for command work.
*/
static void sil680_set_piomode(struct ata_port *ap, struct ata_device *adev)
{
static u16 speed_p[5] = { 0x328A, 0x2283, 0x1104, 0x10C3, 0x10C1 };
static u16 speed_t[5] = { 0x328A, 0x2283, 0x1281, 0x10C3, 0x10C1 };
unsigned long tfaddr = sil680_selreg(ap, 0x02);
unsigned long addr = sil680_seldev(ap, adev, 0x04);
unsigned long addr_mask = 0x80 + 4 * ap->port_no;
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
int pio = adev->pio_mode - XFER_PIO_0;
int lowest_pio = pio;
int port_shift = 4 * adev->devno;
u16 reg;
u8 mode;
struct ata_device *pair = ata_dev_pair(adev);
if (pair != NULL && adev->pio_mode > pair->pio_mode)
lowest_pio = pair->pio_mode - XFER_PIO_0;
pci_write_config_word(pdev, addr, speed_p[pio]);
pci_write_config_word(pdev, tfaddr, speed_t[lowest_pio]);
pci_read_config_word(pdev, tfaddr-2, &reg);
pci_read_config_byte(pdev, addr_mask, &mode);
reg &= ~0x0200; /* Clear IORDY */
mode &= ~(3 << port_shift); /* Clear IORDY and DMA bits */
if (ata_pio_need_iordy(adev)) {
reg |= 0x0200; /* Enable IORDY */
mode |= 1 << port_shift;
}
pci_write_config_word(pdev, tfaddr-2, reg);
pci_write_config_byte(pdev, addr_mask, mode);
}
/**
* sil680_set_dmamode - set initial DMA mode data
* @ap: ATA interface
* @adev: ATA device
*
* Program the MWDMA/UDMA modes for the sil680 k
* chipset. The MWDMA mode values are pulled from a lookup table
* while the chipset uses mode number for UDMA.
*/
static void sil680_set_dmamode(struct ata_port *ap, struct ata_device *adev)
{
static u8 ultra_table[2][7] = {
{ 0x0C, 0x07, 0x05, 0x04, 0x02, 0x01, 0xFF }, /* 100MHz */
{ 0x0F, 0x0B, 0x07, 0x05, 0x03, 0x02, 0x01 }, /* 133Mhz */
};
static u16 dma_table[3] = { 0x2208, 0x10C2, 0x10C1 };
struct pci_dev *pdev = to_pci_dev(ap->host->dev);
unsigned long ma = sil680_seldev(ap, adev, 0x08);
unsigned long ua = sil680_seldev(ap, adev, 0x0C);
unsigned long addr_mask = 0x80 + 4 * ap->port_no;
int port_shift = adev->devno * 4;
u8 scsc, mode;
u16 multi, ultra;
pci_read_config_byte(pdev, 0x8A, &scsc);
pci_read_config_byte(pdev, addr_mask, &mode);
pci_read_config_word(pdev, ma, &multi);
pci_read_config_word(pdev, ua, &ultra);
/* Mask timing bits */
ultra &= ~0x3F;
mode &= ~(0x03 << port_shift);
/* Extract scsc */
scsc = (scsc & 0x30) ? 1: 0;
if (adev->dma_mode >= XFER_UDMA_0) {
multi = 0x10C1;
ultra |= ultra_table[scsc][adev->dma_mode - XFER_UDMA_0];
mode |= (0x03 << port_shift);
} else {
multi = dma_table[adev->dma_mode - XFER_MW_DMA_0];
mode |= (0x02 << port_shift);
}
pci_write_config_byte(pdev, addr_mask, mode);
pci_write_config_word(pdev, ma, multi);
pci_write_config_word(pdev, ua, ultra);
}
static struct scsi_host_template sil680_sht = {
.module = THIS_MODULE,
.name = DRV_NAME,
.ioctl = ata_scsi_ioctl,
.queuecommand = ata_scsi_queuecmd,
.can_queue = ATA_DEF_QUEUE,
.this_id = ATA_SHT_THIS_ID,
.sg_tablesize = LIBATA_MAX_PRD,
.cmd_per_lun = ATA_SHT_CMD_PER_LUN,
.emulated = ATA_SHT_EMULATED,
.use_clustering = ATA_SHT_USE_CLUSTERING,
.proc_name = DRV_NAME,
.dma_boundary = ATA_DMA_BOUNDARY,
.slave_configure = ata_scsi_slave_config,
.slave_destroy = ata_scsi_slave_destroy,
.bios_param = ata_std_bios_param,
};
static struct ata_port_operations sil680_port_ops = {
.port_disable = ata_port_disable,
.set_piomode = sil680_set_piomode,
.set_dmamode = sil680_set_dmamode,
.mode_filter = ata_pci_default_filter,
.tf_load = ata_tf_load,
.tf_read = ata_tf_read,
.check_status = ata_check_status,
.exec_command = ata_exec_command,
.dev_select = ata_std_dev_select,
.freeze = ata_bmdma_freeze,
.thaw = ata_bmdma_thaw,
.error_handler = sil680_error_handler,
.post_internal_cmd = ata_bmdma_post_internal_cmd,
.cable_detect = sil680_cable_detect,
.bmdma_setup = ata_bmdma_setup,
.bmdma_start = ata_bmdma_start,
.bmdma_stop = ata_bmdma_stop,
.bmdma_status = ata_bmdma_status,
.qc_prep = ata_qc_prep,
.qc_issue = ata_qc_issue_prot,
.data_xfer = ata_data_xfer,
.irq_handler = ata_interrupt,
.irq_clear = ata_bmdma_irq_clear,
.irq_on = ata_irq_on,
.irq_ack = ata_irq_ack,
.port_start = ata_port_start,
};
/**
* sil680_init_chip - chip setup
* @pdev: PCI device
*
* Perform all the chip setup which must be done both when the device
* is powered up on boot and when we resume in case we resumed from RAM.
* Returns the final clock settings.
*/
static u8 sil680_init_chip(struct pci_dev *pdev)
{
u32 class_rev = 0;
u8 tmpbyte = 0;
pci_read_config_dword(pdev, PCI_CLASS_REVISION, &class_rev);
class_rev &= 0xff;
/* FIXME: double check */
pci_write_config_byte(pdev, PCI_CACHE_LINE_SIZE, (class_rev) ? 1 : 255);
pci_write_config_byte(pdev, 0x80, 0x00);
pci_write_config_byte(pdev, 0x84, 0x00);
pci_read_config_byte(pdev, 0x8A, &tmpbyte);
printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n",
tmpbyte & 1, tmpbyte & 0x30);
switch(tmpbyte & 0x30) {
case 0x00:
/* 133 clock attempt to force it on */
pci_write_config_byte(pdev, 0x8A, tmpbyte|0x10);
break;
case 0x30:
/* if clocking is disabled */
/* 133 clock attempt to force it on */
pci_write_config_byte(pdev, 0x8A, tmpbyte & ~0x20);
break;
case 0x10:
/* 133 already */
break;
case 0x20:
/* BIOS set PCI x2 clocking */
break;
}
pci_read_config_byte(pdev, 0x8A, &tmpbyte);
printk(KERN_INFO "sil680: BA5_EN = %d clock = %02X\n",
tmpbyte & 1, tmpbyte & 0x30);
pci_write_config_byte(pdev, 0xA1, 0x72);
pci_write_config_word(pdev, 0xA2, 0x328A);
pci_write_config_dword(pdev, 0xA4, 0x62DD62DD);
pci_write_config_dword(pdev, 0xA8, 0x43924392);
pci_write_config_dword(pdev, 0xAC, 0x40094009);
pci_write_config_byte(pdev, 0xB1, 0x72);
pci_write_config_word(pdev, 0xB2, 0x328A);
pci_write_config_dword(pdev, 0xB4, 0x62DD62DD);
pci_write_config_dword(pdev, 0xB8, 0x43924392);
pci_write_config_dword(pdev, 0xBC, 0x40094009);
switch(tmpbyte & 0x30) {
case 0x00: printk(KERN_INFO "sil680: 100MHz clock.\n");break;
case 0x10: printk(KERN_INFO "sil680: 133MHz clock.\n");break;
case 0x20: printk(KERN_INFO "sil680: Using PCI clock.\n");break;
/* This last case is _NOT_ ok */
case 0x30: printk(KERN_ERR "sil680: Clock disabled ?\n");
}
return tmpbyte & 0x30;
}
static int sil680_init_one(struct pci_dev *pdev, const struct pci_device_id *id)
{
static const struct ata_port_info info = {
.sht = &sil680_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x7f,
.port_ops = &sil680_port_ops
};
static const struct ata_port_info info_slow = {
.sht = &sil680_sht,
.flags = ATA_FLAG_SLAVE_POSS | ATA_FLAG_SRST,
.pio_mask = 0x1f,
.mwdma_mask = 0x07,
.udma_mask = 0x3f,
.port_ops = &sil680_port_ops
};
const struct ata_port_info *ppi[] = { &info, NULL };
static int printed_version;
if (!printed_version++)
dev_printk(KERN_DEBUG, &pdev->dev, "version " DRV_VERSION "\n");
switch(sil680_init_chip(pdev))
{
case 0:
ppi[0] = &info_slow;
break;
case 0x30:
return -ENODEV;
}
return ata_pci_init_one(pdev, ppi);
}
#ifdef CONFIG_PM
static int sil680_reinit_one(struct pci_dev *pdev)
{
sil680_init_chip(pdev);
return ata_pci_device_resume(pdev);
}
#endif
static const struct pci_device_id sil680[] = {
{ PCI_VDEVICE(CMD, PCI_DEVICE_ID_SII_680), },
{ },
};
static struct pci_driver sil680_pci_driver = {
.name = DRV_NAME,
.id_table = sil680,
.probe = sil680_init_one,
.remove = ata_pci_remove_one,
#ifdef CONFIG_PM
.suspend = ata_pci_device_suspend,
.resume = sil680_reinit_one,
#endif
};
static int __init sil680_init(void)
{
return pci_register_driver(&sil680_pci_driver);
}
static void __exit sil680_exit(void)
{
pci_unregister_driver(&sil680_pci_driver);
}
MODULE_AUTHOR("Alan Cox");
MODULE_DESCRIPTION("low-level driver for SI680 PATA");
MODULE_LICENSE("GPL");
MODULE_DEVICE_TABLE(pci, sil680);
MODULE_VERSION(DRV_VERSION);
module_init(sil680_init);
module_exit(sil680_exit);
View Git Blame Copy Permalink