3af350929e
The Amphenol ChipCap 2 is a capacitive polymer humidity and temperature sensor with an integrated EEPROM and minimum/maximum humidity alarms. All device variants offer an I2C interface and depending on the part number, two different output modes: - CC2D: digital output - CC2A: analog (PDM) output This driver adds support for the digital variant (CC2D part numbers), which includes the following part numbers: - non-sleep measurement mode (CC2D23, CC2D25, CC2D33, CC2D35) - sleep measurement mode (CC2D23S, CC2D25S, CC2D33S, CC2D35S) The Chipcap 2 EEPROM can be accessed to configure a series of parameters like the minimum/maximum humidity alarm threshold and hysteresis. The EEPROM is only accessible in the command window after a power-on reset. The default window lasts 10 ms if no Start_CM command is sent. After the command window is finished (either after the mentioned timeout of after a Start_NOM command is sent), the device enters the normal operation mode and makes a first measurement automatically. Unfortunately, the device does not provide any hardware or software reset and therefore the driver must trigger power cycles to enter the command mode. A dedicated, external regulator is required for that. This driver keeps the device off until a measurement or access to the EEPROM is required, making use of the first automatic measurement to avoid different code paths for sleep and non-sleep devices. The minimum and maximum humidity alarms are configured with two registers per alarm: one stores the alarm threshold and the other one keeps the value that turns off the alarm. The alarm signals are only updated when a measurement is carried out. Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com> Link: https://lore.kernel.org/r/20240130-topic-chipcap2-v6-5-260bea05cf9b@gmail.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
74 lines
2.8 KiB
ReStructuredText
74 lines
2.8 KiB
ReStructuredText
.. SPDX-License-Identifier: GPL-2.0-or-later
|
|
|
|
Kernel driver ChipCap2
|
|
======================
|
|
|
|
Supported chips:
|
|
|
|
* Amphenol CC2D23, CC2D23S, CC2D25, CC2D25S, CC2D33, CC2D33S, CC2D35, CC2D35S
|
|
|
|
Prefix: 'chipcap2'
|
|
|
|
Addresses scanned: -
|
|
|
|
Datasheet: https://www.amphenol-sensors.com/en/telaire/humidity/527-humidity-sensors/3095-chipcap-2
|
|
|
|
Author:
|
|
|
|
- Javier Carrasco <javier.carrasco.cruz@gmail.com>
|
|
|
|
Description
|
|
-----------
|
|
|
|
This driver implements support for the Amphenol ChipCap 2, a humidity and
|
|
temperature chip family. Temperature is measured in milli degrees celsius,
|
|
relative humidity is expressed as a per cent mille. The measurement ranges
|
|
are the following:
|
|
|
|
- Relative humidity: 0 to 100000 pcm (14-bit resolution)
|
|
- Temperature: -40000 to +125000 m°C (14-bit resolution)
|
|
|
|
The device communicates with the I2C protocol and uses the I2C address 0x28
|
|
by default.
|
|
|
|
Depending on the hardware configuration, up to two humidity alarms to control
|
|
minimum and maximum values are provided. Their thresholds and hystersis can be
|
|
configured via sysfs.
|
|
|
|
Thresholds and hysteris must be provided as a per cent mille. These values
|
|
might be truncated to match the 14-bit device resolution (6.1 pcm/LSB)
|
|
|
|
Known Issues
|
|
------------
|
|
|
|
The driver does not support I2C address and command window length modification.
|
|
|
|
sysfs-Interface
|
|
---------------
|
|
|
|
The following list includes the sysfs attributes that the driver always provides,
|
|
their permissions and a short description:
|
|
|
|
=============================== ======= ========================================
|
|
Name Perm Description
|
|
=============================== ======= ========================================
|
|
temp1_input: RO temperature input
|
|
humidity1_input: RO humidity input
|
|
=============================== ======= ========================================
|
|
|
|
The following list includes the sysfs attributes that the driver may provide
|
|
depending on the hardware configuration:
|
|
|
|
=============================== ======= ========================================
|
|
Name Perm Description
|
|
=============================== ======= ========================================
|
|
humidity1_min: RW humidity low limit. Measurements under
|
|
this limit trigger a humidity low alarm
|
|
humidity1_max: RW humidity high limit. Measurements above
|
|
this limit trigger a humidity high alarm
|
|
humidity1_min_hyst: RW humidity low hystersis
|
|
humidity1_max_hyst: RW humidity high hystersis
|
|
humidity1_min_alarm: RO humidity low alarm indicator
|
|
humidity1_max_alarm: RO humidity high alarm indicator
|
|
=============================== ======= ========================================
|