kevin/linux
1
Fork 0
Code
24a15a62dc
linux/drivers/usb/serial/ftdi_sio.h
Mark Adamson 094c2e6db4 USB: serial: FTDI: add high speed device support 
Added support for FTDI's USB 2.0 hi-speed devices - FT2232H (2
interfaces) and FT4232H (4 interfaces), including a new baud rate
calculation for these devices which can now achieve up to 12Mbaud by
turning off a divide by 2.5 in the baud rate generator of the chips.  In
order to achieve baud rates of <1200 baud, the divide by 2.5 must be
active.  The default product ID of the FT2232H is 0x6010 (same as the
FT2232C IC).  The default PID of the FT4232H is 0x6011.


Signed-off-by: Mark J. Adamson <mark.adamson@ftdichip.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15 21:44:41 -07:00

1451 lines
51 KiB
C
Raw Blame History

/*
* Definitions for the FTDI USB Single Port Serial Converter -
* known as FTDI_SIO (Serial Input/Output application of the chipset)
*
* The example I have is known as the USC-1000 which is available from
* http://www.dse.co.nz - cat no XH4214 It looks similar to this:
* http://www.dansdata.com/usbser.htm but I can't be sure There are other
* USC-1000s which don't look like my device though so beware!
*
* The device is based on the FTDI FT8U100AX chip. It has a DB25 on one side,
* USB on the other.
*
* Thanx to FTDI (http://www.ftdichip.com) for so kindly providing details
* of the protocol required to talk to the device and ongoing assistence
* during development.
*
* Bill Ryder - bryder@sgi.com formerly of Silicon Graphics, Inc.- wrote the
* FTDI_SIO implementation.
*
* Philipp Gühring - pg@futureware.at - added the Device ID of the USB relais
* from Rudolf Gugler
*
*/
#define FTDI_VID 0x0403 /* Vendor Id */
#define FTDI_SIO_PID 0x8372 /* Product Id SIO application of 8U100AX */
#define FTDI_8U232AM_PID 0x6001 /* Similar device to SIO above */
#define FTDI_8U232AM_ALT_PID 0x6006 /* FTDI's alternate PID for above */
#define FTDI_8U2232C_PID 0x6010 /* Dual channel device */
#define FTDI_232RL_PID 0xFBFA /* Product ID for FT232RL */
#define FTDI_4232H_PID 0x6011 /* Quad channel hi-speed device */
#define FTDI_RELAIS_PID 0xFA10 /* Relais device from Rudolf Gugler */
#define FTDI_NF_RIC_VID 0x0DCD /* Vendor Id */
#define FTDI_NF_RIC_PID 0x0001 /* Product Id */
#define FTDI_USBX_707_PID 0xF857 /* ADSTech IR Blaster USBX-707 */
/* Larsen and Brusgaard AltiTrack/USBtrack */
#define LARSENBRUSGAARD_VID 0x0FD8
#define LB_ALTITRACK_PID 0x0001
/* www.canusb.com Lawicel CANUSB device */
#define FTDI_CANUSB_PID 0xFFA8 /* Product Id */
/* AlphaMicro Components AMC-232USB01 device */
#define FTDI_AMC232_PID 0xFF00 /* Product Id */
/* www.candapter.com Ewert Energy Systems CANdapter device */
#define FTDI_CANDAPTER_PID 0x9F80 /* Product Id */
/* SCS HF Radio Modems PID's (http://www.scs-ptc.com) */
/* the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_SCS_DEVICE_0_PID 0xD010 /* SCS PTC-IIusb */
#define FTDI_SCS_DEVICE_1_PID 0xD011 /* SCS Tracker / DSP TNC */
#define FTDI_SCS_DEVICE_2_PID 0xD012
#define FTDI_SCS_DEVICE_3_PID 0xD013
#define FTDI_SCS_DEVICE_4_PID 0xD014
#define FTDI_SCS_DEVICE_5_PID 0xD015
#define FTDI_SCS_DEVICE_6_PID 0xD016
#define FTDI_SCS_DEVICE_7_PID 0xD017
/* ACT Solutions HomePro ZWave interface (http://www.act-solutions.com/HomePro.htm) */
#define FTDI_ACTZWAVE_PID 0xF2D0
/* www.starting-point-systems.com µChameleon device */
#define FTDI_MICRO_CHAMELEON_PID 0xCAA0 /* Product Id */
/* www.irtrans.de device */
#define FTDI_IRTRANS_PID 0xFC60 /* Product Id */
/* www.thoughttechnology.com/ TT-USB provide with procomp use ftdi_sio */
#define FTDI_TTUSB_PID 0xFF20 /* Product Id */
/* iPlus device */
#define FTDI_IPLUS_PID 0xD070 /* Product Id */
#define FTDI_IPLUS2_PID 0xD071 /* Product Id */
/* DMX4ALL DMX Interfaces */
#define FTDI_DMX4ALL 0xC850
/* OpenDCC (www.opendcc.de) product id */
#define FTDI_OPENDCC_PID 0xBFD8
/* Sprog II (Andrew Crosland's SprogII DCC interface) */
#define FTDI_SPROG_II 0xF0C8
/* www.crystalfontz.com devices - thanx for providing free devices for evaluation ! */
/* they use the ftdi chipset for the USB interface and the vendor id is the same */
#define FTDI_XF_632_PID 0xFC08 /* 632: 16x2 Character Display */
#define FTDI_XF_634_PID 0xFC09 /* 634: 20x4 Character Display */
#define FTDI_XF_547_PID 0xFC0A /* 547: Two line Display */
#define FTDI_XF_633_PID 0xFC0B /* 633: 16x2 Character Display with Keys */
#define FTDI_XF_631_PID 0xFC0C /* 631: 20x2 Character Display */
#define FTDI_XF_635_PID 0xFC0D /* 635: 20x4 Character Display */
#define FTDI_XF_640_PID 0xFC0E /* 640: Two line Display */
#define FTDI_XF_642_PID 0xFC0F /* 642: Two line Display */
/* Video Networks Limited / Homechoice in the UK use an ftdi-based device for their 1Mb */
/* broadband internet service. The following PID is exhibited by the usb device supplied */
/* (the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_VNHCPCUSB_D_PID 0xfe38 /* Product Id */
/*
* PCDJ use ftdi based dj-controllers. The following PID is for their DAC-2 device
* http://www.pcdjhardware.com/DAC2.asp (PID sent by Wouter Paesen)
* (the VID is the standard ftdi vid (FTDI_VID) */
#define FTDI_PCDJ_DAC2_PID 0xFA88
/*
* The following are the values for the Matrix Orbital LCD displays,
* which are the FT232BM ( similar to the 8U232AM )
*/
#define FTDI_MTXORB_0_PID 0xFA00 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_1_PID 0xFA01 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_2_PID 0xFA02 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_3_PID 0xFA03 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_4_PID 0xFA04 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_5_PID 0xFA05 /* Matrix Orbital Product Id */
#define FTDI_MTXORB_6_PID 0xFA06 /* Matrix Orbital Product Id */
/* OOCDlink by Joern Kaipf <joernk@web.de>
* (http://www.joernonline.de/dw/doku.php?id=start&idx=projects:oocdlink) */
#define FTDI_OOCDLINK_PID 0xbaf8 /* Amontec JTAGkey */
/*
* The following are the values for the Matrix Orbital FTDI Range
* Anything in this range will use an FT232RL.
*/
#define MTXORB_VID 0x1B3D
#define MTXORB_FTDI_RANGE_0100_PID 0x0100
#define MTXORB_FTDI_RANGE_0101_PID 0x0101
#define MTXORB_FTDI_RANGE_0102_PID 0x0102
#define MTXORB_FTDI_RANGE_0103_PID 0x0103
#define MTXORB_FTDI_RANGE_0104_PID 0x0104
#define MTXORB_FTDI_RANGE_0105_PID 0x0105
#define MTXORB_FTDI_RANGE_0106_PID 0x0106
#define MTXORB_FTDI_RANGE_0107_PID 0x0107
#define MTXORB_FTDI_RANGE_0108_PID 0x0108
#define MTXORB_FTDI_RANGE_0109_PID 0x0109
#define MTXORB_FTDI_RANGE_010A_PID 0x010A
#define MTXORB_FTDI_RANGE_010B_PID 0x010B
#define MTXORB_FTDI_RANGE_010C_PID 0x010C
#define MTXORB_FTDI_RANGE_010D_PID 0x010D
#define MTXORB_FTDI_RANGE_010E_PID 0x010E
#define MTXORB_FTDI_RANGE_010F_PID 0x010F
#define MTXORB_FTDI_RANGE_0110_PID 0x0110
#define MTXORB_FTDI_RANGE_0111_PID 0x0111
#define MTXORB_FTDI_RANGE_0112_PID 0x0112
#define MTXORB_FTDI_RANGE_0113_PID 0x0113
#define MTXORB_FTDI_RANGE_0114_PID 0x0114
#define MTXORB_FTDI_RANGE_0115_PID 0x0115
#define MTXORB_FTDI_RANGE_0116_PID 0x0116
#define MTXORB_FTDI_RANGE_0117_PID 0x0117
#define MTXORB_FTDI_RANGE_0118_PID 0x0118
#define MTXORB_FTDI_RANGE_0119_PID 0x0119
#define MTXORB_FTDI_RANGE_011A_PID 0x011A
#define MTXORB_FTDI_RANGE_011B_PID 0x011B
#define MTXORB_FTDI_RANGE_011C_PID 0x011C
#define MTXORB_FTDI_RANGE_011D_PID 0x011D
#define MTXORB_FTDI_RANGE_011E_PID 0x011E
#define MTXORB_FTDI_RANGE_011F_PID 0x011F
#define MTXORB_FTDI_RANGE_0120_PID 0x0120
#define MTXORB_FTDI_RANGE_0121_PID 0x0121
#define MTXORB_FTDI_RANGE_0122_PID 0x0122
#define MTXORB_FTDI_RANGE_0123_PID 0x0123
#define MTXORB_FTDI_RANGE_0124_PID 0x0124
#define MTXORB_FTDI_RANGE_0125_PID 0x0125
#define MTXORB_FTDI_RANGE_0126_PID 0x0126
#define MTXORB_FTDI_RANGE_0127_PID 0x0127
#define MTXORB_FTDI_RANGE_0128_PID 0x0128
#define MTXORB_FTDI_RANGE_0129_PID 0x0129
#define MTXORB_FTDI_RANGE_012A_PID 0x012A
#define MTXORB_FTDI_RANGE_012B_PID 0x012B
#define MTXORB_FTDI_RANGE_012C_PID 0x012C
#define MTXORB_FTDI_RANGE_012D_PID 0x012D
#define MTXORB_FTDI_RANGE_012E_PID 0x012E
#define MTXORB_FTDI_RANGE_012F_PID 0x012F
#define MTXORB_FTDI_RANGE_0130_PID 0x0130
#define MTXORB_FTDI_RANGE_0131_PID 0x0131
#define MTXORB_FTDI_RANGE_0132_PID 0x0132
#define MTXORB_FTDI_RANGE_0133_PID 0x0133
#define MTXORB_FTDI_RANGE_0134_PID 0x0134
#define MTXORB_FTDI_RANGE_0135_PID 0x0135
#define MTXORB_FTDI_RANGE_0136_PID 0x0136
#define MTXORB_FTDI_RANGE_0137_PID 0x0137
#define MTXORB_FTDI_RANGE_0138_PID 0x0138
#define MTXORB_FTDI_RANGE_0139_PID 0x0139
#define MTXORB_FTDI_RANGE_013A_PID 0x013A
#define MTXORB_FTDI_RANGE_013B_PID 0x013B
#define MTXORB_FTDI_RANGE_013C_PID 0x013C
#define MTXORB_FTDI_RANGE_013D_PID 0x013D
#define MTXORB_FTDI_RANGE_013E_PID 0x013E
#define MTXORB_FTDI_RANGE_013F_PID 0x013F
#define MTXORB_FTDI_RANGE_0140_PID 0x0140
#define MTXORB_FTDI_RANGE_0141_PID 0x0141
#define MTXORB_FTDI_RANGE_0142_PID 0x0142
#define MTXORB_FTDI_RANGE_0143_PID 0x0143
#define MTXORB_FTDI_RANGE_0144_PID 0x0144
#define MTXORB_FTDI_RANGE_0145_PID 0x0145
#define MTXORB_FTDI_RANGE_0146_PID 0x0146
#define MTXORB_FTDI_RANGE_0147_PID 0x0147
#define MTXORB_FTDI_RANGE_0148_PID 0x0148
#define MTXORB_FTDI_RANGE_0149_PID 0x0149
#define MTXORB_FTDI_RANGE_014A_PID 0x014A
#define MTXORB_FTDI_RANGE_014B_PID 0x014B
#define MTXORB_FTDI_RANGE_014C_PID 0x014C
#define MTXORB_FTDI_RANGE_014D_PID 0x014D
#define MTXORB_FTDI_RANGE_014E_PID 0x014E
#define MTXORB_FTDI_RANGE_014F_PID 0x014F
#define MTXORB_FTDI_RANGE_0150_PID 0x0150
#define MTXORB_FTDI_RANGE_0151_PID 0x0151
#define MTXORB_FTDI_RANGE_0152_PID 0x0152
#define MTXORB_FTDI_RANGE_0153_PID 0x0153
#define MTXORB_FTDI_RANGE_0154_PID 0x0154
#define MTXORB_FTDI_RANGE_0155_PID 0x0155
#define MTXORB_FTDI_RANGE_0156_PID 0x0156
#define MTXORB_FTDI_RANGE_0157_PID 0x0157
#define MTXORB_FTDI_RANGE_0158_PID 0x0158
#define MTXORB_FTDI_RANGE_0159_PID 0x0159
#define MTXORB_FTDI_RANGE_015A_PID 0x015A
#define MTXORB_FTDI_RANGE_015B_PID 0x015B
#define MTXORB_FTDI_RANGE_015C_PID 0x015C
#define MTXORB_FTDI_RANGE_015D_PID 0x015D
#define MTXORB_FTDI_RANGE_015E_PID 0x015E
#define MTXORB_FTDI_RANGE_015F_PID 0x015F
#define MTXORB_FTDI_RANGE_0160_PID 0x0160
#define MTXORB_FTDI_RANGE_0161_PID 0x0161
#define MTXORB_FTDI_RANGE_0162_PID 0x0162
#define MTXORB_FTDI_RANGE_0163_PID 0x0163
#define MTXORB_FTDI_RANGE_0164_PID 0x0164
#define MTXORB_FTDI_RANGE_0165_PID 0x0165
#define MTXORB_FTDI_RANGE_0166_PID 0x0166
#define MTXORB_FTDI_RANGE_0167_PID 0x0167
#define MTXORB_FTDI_RANGE_0168_PID 0x0168
#define MTXORB_FTDI_RANGE_0169_PID 0x0169
#define MTXORB_FTDI_RANGE_016A_PID 0x016A
#define MTXORB_FTDI_RANGE_016B_PID 0x016B
#define MTXORB_FTDI_RANGE_016C_PID 0x016C
#define MTXORB_FTDI_RANGE_016D_PID 0x016D
#define MTXORB_FTDI_RANGE_016E_PID 0x016E
#define MTXORB_FTDI_RANGE_016F_PID 0x016F
#define MTXORB_FTDI_RANGE_0170_PID 0x0170
#define MTXORB_FTDI_RANGE_0171_PID 0x0171
#define MTXORB_FTDI_RANGE_0172_PID 0x0172
#define MTXORB_FTDI_RANGE_0173_PID 0x0173
#define MTXORB_FTDI_RANGE_0174_PID 0x0174
#define MTXORB_FTDI_RANGE_0175_PID 0x0175
#define MTXORB_FTDI_RANGE_0176_PID 0x0176
#define MTXORB_FTDI_RANGE_0177_PID 0x0177
#define MTXORB_FTDI_RANGE_0178_PID 0x0178
#define MTXORB_FTDI_RANGE_0179_PID 0x0179
#define MTXORB_FTDI_RANGE_017A_PID 0x017A
#define MTXORB_FTDI_RANGE_017B_PID 0x017B
#define MTXORB_FTDI_RANGE_017C_PID 0x017C
#define MTXORB_FTDI_RANGE_017D_PID 0x017D
#define MTXORB_FTDI_RANGE_017E_PID 0x017E
#define MTXORB_FTDI_RANGE_017F_PID 0x017F
#define MTXORB_FTDI_RANGE_0180_PID 0x0180
#define MTXORB_FTDI_RANGE_0181_PID 0x0181
#define MTXORB_FTDI_RANGE_0182_PID 0x0182
#define MTXORB_FTDI_RANGE_0183_PID 0x0183
#define MTXORB_FTDI_RANGE_0184_PID 0x0184
#define MTXORB_FTDI_RANGE_0185_PID 0x0185
#define MTXORB_FTDI_RANGE_0186_PID 0x0186
#define MTXORB_FTDI_RANGE_0187_PID 0x0187
#define MTXORB_FTDI_RANGE_0188_PID 0x0188
#define MTXORB_FTDI_RANGE_0189_PID 0x0189
#define MTXORB_FTDI_RANGE_018A_PID 0x018A
#define MTXORB_FTDI_RANGE_018B_PID 0x018B
#define MTXORB_FTDI_RANGE_018C_PID 0x018C
#define MTXORB_FTDI_RANGE_018D_PID 0x018D
#define MTXORB_FTDI_RANGE_018E_PID 0x018E
#define MTXORB_FTDI_RANGE_018F_PID 0x018F
#define MTXORB_FTDI_RANGE_0190_PID 0x0190
#define MTXORB_FTDI_RANGE_0191_PID 0x0191
#define MTXORB_FTDI_RANGE_0192_PID 0x0192
#define MTXORB_FTDI_RANGE_0193_PID 0x0193
#define MTXORB_FTDI_RANGE_0194_PID 0x0194
#define MTXORB_FTDI_RANGE_0195_PID 0x0195
#define MTXORB_FTDI_RANGE_0196_PID 0x0196
#define MTXORB_FTDI_RANGE_0197_PID 0x0197
#define MTXORB_FTDI_RANGE_0198_PID 0x0198
#define MTXORB_FTDI_RANGE_0199_PID 0x0199
#define MTXORB_FTDI_RANGE_019A_PID 0x019A
#define MTXORB_FTDI_RANGE_019B_PID 0x019B
#define MTXORB_FTDI_RANGE_019C_PID 0x019C
#define MTXORB_FTDI_RANGE_019D_PID 0x019D
#define MTXORB_FTDI_RANGE_019E_PID 0x019E
#define MTXORB_FTDI_RANGE_019F_PID 0x019F
#define MTXORB_FTDI_RANGE_01A0_PID 0x01A0
#define MTXORB_FTDI_RANGE_01A1_PID 0x01A1
#define MTXORB_FTDI_RANGE_01A2_PID 0x01A2
#define MTXORB_FTDI_RANGE_01A3_PID 0x01A3
#define MTXORB_FTDI_RANGE_01A4_PID 0x01A4
#define MTXORB_FTDI_RANGE_01A5_PID 0x01A5
#define MTXORB_FTDI_RANGE_01A6_PID 0x01A6
#define MTXORB_FTDI_RANGE_01A7_PID 0x01A7
#define MTXORB_FTDI_RANGE_01A8_PID 0x01A8
#define MTXORB_FTDI_RANGE_01A9_PID 0x01A9
#define MTXORB_FTDI_RANGE_01AA_PID 0x01AA
#define MTXORB_FTDI_RANGE_01AB_PID 0x01AB
#define MTXORB_FTDI_RANGE_01AC_PID 0x01AC
#define MTXORB_FTDI_RANGE_01AD_PID 0x01AD
#define MTXORB_FTDI_RANGE_01AE_PID 0x01AE
#define MTXORB_FTDI_RANGE_01AF_PID 0x01AF
#define MTXORB_FTDI_RANGE_01B0_PID 0x01B0
#define MTXORB_FTDI_RANGE_01B1_PID 0x01B1
#define MTXORB_FTDI_RANGE_01B2_PID 0x01B2
#define MTXORB_FTDI_RANGE_01B3_PID 0x01B3
#define MTXORB_FTDI_RANGE_01B4_PID 0x01B4
#define MTXORB_FTDI_RANGE_01B5_PID 0x01B5
#define MTXORB_FTDI_RANGE_01B6_PID 0x01B6
#define MTXORB_FTDI_RANGE_01B7_PID 0x01B7
#define MTXORB_FTDI_RANGE_01B8_PID 0x01B8
#define MTXORB_FTDI_RANGE_01B9_PID 0x01B9
#define MTXORB_FTDI_RANGE_01BA_PID 0x01BA
#define MTXORB_FTDI_RANGE_01BB_PID 0x01BB
#define MTXORB_FTDI_RANGE_01BC_PID 0x01BC
#define MTXORB_FTDI_RANGE_01BD_PID 0x01BD
#define MTXORB_FTDI_RANGE_01BE_PID 0x01BE
#define MTXORB_FTDI_RANGE_01BF_PID 0x01BF
#define MTXORB_FTDI_RANGE_01C0_PID 0x01C0
#define MTXORB_FTDI_RANGE_01C1_PID 0x01C1
#define MTXORB_FTDI_RANGE_01C2_PID 0x01C2
#define MTXORB_FTDI_RANGE_01C3_PID 0x01C3
#define MTXORB_FTDI_RANGE_01C4_PID 0x01C4
#define MTXORB_FTDI_RANGE_01C5_PID 0x01C5
#define MTXORB_FTDI_RANGE_01C6_PID 0x01C6
#define MTXORB_FTDI_RANGE_01C7_PID 0x01C7
#define MTXORB_FTDI_RANGE_01C8_PID 0x01C8
#define MTXORB_FTDI_RANGE_01C9_PID 0x01C9
#define MTXORB_FTDI_RANGE_01CA_PID 0x01CA
#define MTXORB_FTDI_RANGE_01CB_PID 0x01CB
#define MTXORB_FTDI_RANGE_01CC_PID 0x01CC
#define MTXORB_FTDI_RANGE_01CD_PID 0x01CD
#define MTXORB_FTDI_RANGE_01CE_PID 0x01CE
#define MTXORB_FTDI_RANGE_01CF_PID 0x01CF
#define MTXORB_FTDI_RANGE_01D0_PID 0x01D0
#define MTXORB_FTDI_RANGE_01D1_PID 0x01D1
#define MTXORB_FTDI_RANGE_01D2_PID 0x01D2
#define MTXORB_FTDI_RANGE_01D3_PID 0x01D3
#define MTXORB_FTDI_RANGE_01D4_PID 0x01D4
#define MTXORB_FTDI_RANGE_01D5_PID 0x01D5
#define MTXORB_FTDI_RANGE_01D6_PID 0x01D6
#define MTXORB_FTDI_RANGE_01D7_PID 0x01D7
#define MTXORB_FTDI_RANGE_01D8_PID 0x01D8
#define MTXORB_FTDI_RANGE_01D9_PID 0x01D9
#define MTXORB_FTDI_RANGE_01DA_PID 0x01DA
#define MTXORB_FTDI_RANGE_01DB_PID 0x01DB
#define MTXORB_FTDI_RANGE_01DC_PID 0x01DC
#define MTXORB_FTDI_RANGE_01DD_PID 0x01DD
#define MTXORB_FTDI_RANGE_01DE_PID 0x01DE
#define MTXORB_FTDI_RANGE_01DF_PID 0x01DF
#define MTXORB_FTDI_RANGE_01E0_PID 0x01E0
#define MTXORB_FTDI_RANGE_01E1_PID 0x01E1
#define MTXORB_FTDI_RANGE_01E2_PID 0x01E2
#define MTXORB_FTDI_RANGE_01E3_PID 0x01E3
#define MTXORB_FTDI_RANGE_01E4_PID 0x01E4
#define MTXORB_FTDI_RANGE_01E5_PID 0x01E5
#define MTXORB_FTDI_RANGE_01E6_PID 0x01E6
#define MTXORB_FTDI_RANGE_01E7_PID 0x01E7
#define MTXORB_FTDI_RANGE_01E8_PID 0x01E8
#define MTXORB_FTDI_RANGE_01E9_PID 0x01E9
#define MTXORB_FTDI_RANGE_01EA_PID 0x01EA
#define MTXORB_FTDI_RANGE_01EB_PID 0x01EB
#define MTXORB_FTDI_RANGE_01EC_PID 0x01EC
#define MTXORB_FTDI_RANGE_01ED_PID 0x01ED
#define MTXORB_FTDI_RANGE_01EE_PID 0x01EE
#define MTXORB_FTDI_RANGE_01EF_PID 0x01EF
#define MTXORB_FTDI_RANGE_01F0_PID 0x01F0
#define MTXORB_FTDI_RANGE_01F1_PID 0x01F1
#define MTXORB_FTDI_RANGE_01F2_PID 0x01F2
#define MTXORB_FTDI_RANGE_01F3_PID 0x01F3
#define MTXORB_FTDI_RANGE_01F4_PID 0x01F4
#define MTXORB_FTDI_RANGE_01F5_PID 0x01F5
#define MTXORB_FTDI_RANGE_01F6_PID 0x01F6
#define MTXORB_FTDI_RANGE_01F7_PID 0x01F7
#define MTXORB_FTDI_RANGE_01F8_PID 0x01F8
#define MTXORB_FTDI_RANGE_01F9_PID 0x01F9
#define MTXORB_FTDI_RANGE_01FA_PID 0x01FA
#define MTXORB_FTDI_RANGE_01FB_PID 0x01FB
#define MTXORB_FTDI_RANGE_01FC_PID 0x01FC
#define MTXORB_FTDI_RANGE_01FD_PID 0x01FD
#define MTXORB_FTDI_RANGE_01FE_PID 0x01FE
#define MTXORB_FTDI_RANGE_01FF_PID 0x01FF
/* Interbiometrics USB I/O Board */
/* Developed for Interbiometrics by Rudolf Gugler */
#define INTERBIOMETRICS_VID 0x1209
#define INTERBIOMETRICS_IOBOARD_PID 0x1002
#define INTERBIOMETRICS_MINI_IOBOARD_PID 0x1006
/*
* The following are the values for the Perle Systems
* UltraPort USB serial converters
*/
#define FTDI_PERLE_ULTRAPORT_PID 0xF0C0 /* Perle UltraPort Product Id */
/*
* The following are the values for the Sealevel SeaLINK+ adapters.
* (Original list sent by Tuan Hoang. Ian Abbott renamed the macros and
* removed some PIDs that don't seem to match any existing products.)
*/
#define SEALEVEL_VID 0x0c52 /* Sealevel Vendor ID */
#define SEALEVEL_2101_PID 0x2101 /* SeaLINK+232 (2101/2105) */
#define SEALEVEL_2102_PID 0x2102 /* SeaLINK+485 (2102) */
#define SEALEVEL_2103_PID 0x2103 /* SeaLINK+232I (2103) */
#define SEALEVEL_2104_PID 0x2104 /* SeaLINK+485I (2104) */
#define SEALEVEL_2106_PID 0x9020 /* SeaLINK+422 (2106) */
#define SEALEVEL_2201_1_PID 0x2211 /* SeaPORT+2/232 (2201) Port 1 */
#define SEALEVEL_2201_2_PID 0x2221 /* SeaPORT+2/232 (2201) Port 2 */
#define SEALEVEL_2202_1_PID 0x2212 /* SeaPORT+2/485 (2202) Port 1 */
#define SEALEVEL_2202_2_PID 0x2222 /* SeaPORT+2/485 (2202) Port 2 */
#define SEALEVEL_2203_1_PID 0x2213 /* SeaPORT+2 (2203) Port 1 */
#define SEALEVEL_2203_2_PID 0x2223 /* SeaPORT+2 (2203) Port 2 */
#define SEALEVEL_2401_1_PID 0x2411 /* SeaPORT+4/232 (2401) Port 1 */
#define SEALEVEL_2401_2_PID 0x2421 /* SeaPORT+4/232 (2401) Port 2 */
#define SEALEVEL_2401_3_PID 0x2431 /* SeaPORT+4/232 (2401) Port 3 */
#define SEALEVEL_2401_4_PID 0x2441 /* SeaPORT+4/232 (2401) Port 4 */
#define SEALEVEL_2402_1_PID 0x2412 /* SeaPORT+4/485 (2402) Port 1 */
#define SEALEVEL_2402_2_PID 0x2422 /* SeaPORT+4/485 (2402) Port 2 */
#define SEALEVEL_2402_3_PID 0x2432 /* SeaPORT+4/485 (2402) Port 3 */
#define SEALEVEL_2402_4_PID 0x2442 /* SeaPORT+4/485 (2402) Port 4 */
#define SEALEVEL_2403_1_PID 0x2413 /* SeaPORT+4 (2403) Port 1 */
#define SEALEVEL_2403_2_PID 0x2423 /* SeaPORT+4 (2403) Port 2 */
#define SEALEVEL_2403_3_PID 0x2433 /* SeaPORT+4 (2403) Port 3 */
#define SEALEVEL_2403_4_PID 0x2443 /* SeaPORT+4 (2403) Port 4 */
#define SEALEVEL_2801_1_PID 0X2811 /* SeaLINK+8/232 (2801) Port 1 */
#define SEALEVEL_2801_2_PID 0X2821 /* SeaLINK+8/232 (2801) Port 2 */
#define SEALEVEL_2801_3_PID 0X2831 /* SeaLINK+8/232 (2801) Port 3 */
#define SEALEVEL_2801_4_PID 0X2841 /* SeaLINK+8/232 (2801) Port 4 */
#define SEALEVEL_2801_5_PID 0X2851 /* SeaLINK+8/232 (2801) Port 5 */
#define SEALEVEL_2801_6_PID 0X2861 /* SeaLINK+8/232 (2801) Port 6 */
#define SEALEVEL_2801_7_PID 0X2871 /* SeaLINK+8/232 (2801) Port 7 */
#define SEALEVEL_2801_8_PID 0X2881 /* SeaLINK+8/232 (2801) Port 8 */
#define SEALEVEL_2802_1_PID 0X2812 /* SeaLINK+8/485 (2802) Port 1 */
#define SEALEVEL_2802_2_PID 0X2822 /* SeaLINK+8/485 (2802) Port 2 */
#define SEALEVEL_2802_3_PID 0X2832 /* SeaLINK+8/485 (2802) Port 3 */
#define SEALEVEL_2802_4_PID 0X2842 /* SeaLINK+8/485 (2802) Port 4 */
#define SEALEVEL_2802_5_PID 0X2852 /* SeaLINK+8/485 (2802) Port 5 */
#define SEALEVEL_2802_6_PID 0X2862 /* SeaLINK+8/485 (2802) Port 6 */
#define SEALEVEL_2802_7_PID 0X2872 /* SeaLINK+8/485 (2802) Port 7 */
#define SEALEVEL_2802_8_PID 0X2882 /* SeaLINK+8/485 (2802) Port 8 */
#define SEALEVEL_2803_1_PID 0X2813 /* SeaLINK+8 (2803) Port 1 */
#define SEALEVEL_2803_2_PID 0X2823 /* SeaLINK+8 (2803) Port 2 */
#define SEALEVEL_2803_3_PID 0X2833 /* SeaLINK+8 (2803) Port 3 */
#define SEALEVEL_2803_4_PID 0X2843 /* SeaLINK+8 (2803) Port 4 */
#define SEALEVEL_2803_5_PID 0X2853 /* SeaLINK+8 (2803) Port 5 */
#define SEALEVEL_2803_6_PID 0X2863 /* SeaLINK+8 (2803) Port 6 */
#define SEALEVEL_2803_7_PID 0X2873 /* SeaLINK+8 (2803) Port 7 */
#define SEALEVEL_2803_8_PID 0X2883 /* SeaLINK+8 (2803) Port 8 */
/*
* The following are the values for two KOBIL chipcard terminals.
*/
#define KOBIL_VID 0x0d46 /* KOBIL Vendor ID */
#define KOBIL_CONV_B1_PID 0x2020 /* KOBIL Konverter for B1 */
#define KOBIL_CONV_KAAN_PID 0x2021 /* KOBIL_Konverter for KAAN */
/*
* Icom ID-1 digital transceiver
*/
#define ICOM_ID1_VID 0x0C26
#define ICOM_ID1_PID 0x0004
/*
* ASK.fr devices
*/
#define FTDI_ASK_RDR400_PID 0xC991 /* ASK RDR 400 series card reader */
/*
* FTDI USB UART chips used in construction projects from the
* Elektor Electronics magazine (http://elektor-electronics.co.uk)
*/
#define ELEKTOR_VID 0x0C7D
#define ELEKTOR_FT323R_PID 0x0005 /* RFID-Reader, issue 09-2006 */
/*
* DSS-20 Sync Station for Sony Ericsson P800
*/
#define FTDI_DSS20_PID 0xFC82
/*
* Home Electronics (www.home-electro.com) USB gadgets
*/
#define FTDI_HE_TIRA1_PID 0xFA78 /* Tira-1 IR transceiver */
/* USB-UIRT - An infrared receiver and transmitter using the 8U232AM chip */
/* http://home.earthlink.net/~jrhees/USBUIRT/index.htm */
#define FTDI_USB_UIRT_PID 0xF850 /* Product Id */
/* TNC-X USB-to-packet-radio adapter, versions prior to 3.0 (DLP module) */
#define FTDI_TNC_X_PID 0xEBE0
/*
* ELV USB devices submitted by Christian Abt of ELV (www.elv.de).
* All of these devices use FTDI's vendor ID (0x0403).
*
* The previously included PID for the UO 100 module was incorrect.
* In fact, that PID was for ELV's UR 100 USB-RS232 converter (0xFB58).
*
* Armin Laeuger originally sent the PID for the UM 100 module.
*/
#define FTDI_ELV_UR100_PID 0xFB58 /* USB-RS232-Umsetzer (UR 100) */
#define FTDI_ELV_UM100_PID 0xFB5A /* USB-Modul UM 100 */
#define FTDI_ELV_UO100_PID 0xFB5B /* USB-Modul UO 100 */
#define FTDI_ELV_ALC8500_PID 0xF06E /* ALC 8500 Expert */
/* Additional ELV PIDs that default to using the FTDI D2XX drivers on
* MS Windows, rather than the FTDI Virtual Com Port drivers.
* Maybe these will be easier to use with the libftdi/libusb user-space
* drivers, or possibly the Comedi drivers in some cases. */
#define FTDI_ELV_CLI7000_PID 0xFB59 /* Computer-Light-Interface (CLI 7000) */
#define FTDI_ELV_PPS7330_PID 0xFB5C /* Processor-Power-Supply (PPS 7330) */
#define FTDI_ELV_TFM100_PID 0xFB5D /* Temperartur-Feuchte Messgeraet (TFM 100) */
#define FTDI_ELV_UDF77_PID 0xFB5E /* USB DCF Funkurh (UDF 77) */
#define FTDI_ELV_UIO88_PID 0xFB5F /* USB-I/O Interface (UIO 88) */
#define FTDI_ELV_UAD8_PID 0xF068 /* USB-AD-Wandler (UAD 8) */
#define FTDI_ELV_UDA7_PID 0xF069 /* USB-DA-Wandler (UDA 7) */
#define FTDI_ELV_USI2_PID 0xF06A /* USB-Schrittmotoren-Interface (USI 2) */
#define FTDI_ELV_T1100_PID 0xF06B /* Thermometer (T 1100) */
#define FTDI_ELV_PCD200_PID 0xF06C /* PC-Datenlogger (PCD 200) */
#define FTDI_ELV_ULA200_PID 0xF06D /* USB-LCD-Ansteuerung (ULA 200) */
#define FTDI_ELV_FHZ1000PC_PID 0xF06F /* FHZ 1000 PC */
#define FTDI_ELV_CSI8_PID 0xE0F0 /* Computer-Schalt-Interface (CSI 8) */
#define FTDI_ELV_EM1000DL_PID 0xE0F1 /* PC-Datenlogger fuer Energiemonitor (EM 1000 DL) */
#define FTDI_ELV_PCK100_PID 0xE0F2 /* PC-Kabeltester (PCK 100) */
#define FTDI_ELV_RFP500_PID 0xE0F3 /* HF-Leistungsmesser (RFP 500) */
#define FTDI_ELV_FS20SIG_PID 0xE0F4 /* Signalgeber (FS 20 SIG) */
#define FTDI_ELV_WS300PC_PID 0xE0F6 /* PC-Wetterstation (WS 300 PC) */
#define FTDI_ELV_FHZ1300PC_PID 0xE0E8 /* FHZ 1300 PC */
#define FTDI_ELV_WS500_PID 0xE0E9 /* PC-Wetterstation (WS 500) */
#define FTDI_ELV_HS485_PID 0xE0EA /* USB to RS-485 adapter */
#define FTDI_ELV_EM1010PC_PID 0xE0EF /* Engery monitor EM 1010 PC */
#define FTDI_PHI_FISCO_PID 0xE40B /* PHI Fisco USB to Serial cable */
/*
* Definitions for ID TECH (www.idt-net.com) devices
*/
#define IDTECH_VID 0x0ACD /* ID TECH Vendor ID */
#define IDTECH_IDT1221U_PID 0x0300 /* IDT1221U USB to RS-232 adapter */
/*
* Definitions for Omnidirectional Control Technology, Inc. devices
*/
#define OCT_VID 0x0B39 /* OCT vendor ID */
/* Note: OCT US101 is also rebadged as Dick Smith Electronics (NZ) XH6381 */
/* Also rebadged as Dick Smith Electronics (Aus) XH6451 */
/* Also rebadged as SIIG Inc. model US2308 hardware version 1 */
#define OCT_US101_PID 0x0421 /* OCT US101 USB to RS-232 */
/* an infrared receiver for user access control with IR tags */
#define FTDI_PIEGROUP_PID 0xF208 /* Product Id */
/*
* Definitions for Artemis astronomical USB based cameras
* Check it at http://www.artemisccd.co.uk/
*/
#define FTDI_ARTEMIS_PID 0xDF28 /* All Artemis Cameras */
/*
* Definitions for ATIK Instruments astronomical USB based cameras
* Check it at http://www.atik-instruments.com/
*/
#define FTDI_ATIK_ATK16_PID 0xDF30 /* ATIK ATK-16 Grayscale Camera */
#define FTDI_ATIK_ATK16C_PID 0xDF32 /* ATIK ATK-16C Colour Camera */
#define FTDI_ATIK_ATK16HR_PID 0xDF31 /* ATIK ATK-16HR Grayscale Camera */
#define FTDI_ATIK_ATK16HRC_PID 0xDF33 /* ATIK ATK-16HRC Colour Camera */
#define FTDI_ATIK_ATK16IC_PID 0xDF35 /* ATIK ATK-16IC Grayscale Camera */
/*
* Protego product ids
*/
#define PROTEGO_SPECIAL_1 0xFC70 /* special/unknown device */
#define PROTEGO_R2X0 0xFC71 /* R200-USB TRNG unit (R210, R220, and R230) */
#define PROTEGO_SPECIAL_3 0xFC72 /* special/unknown device */
#define PROTEGO_SPECIAL_4 0xFC73 /* special/unknown device */
/*
* Gude Analog- und Digitalsysteme GmbH
*/
#define FTDI_GUDEADS_E808_PID 0xE808
#define FTDI_GUDEADS_E809_PID 0xE809
#define FTDI_GUDEADS_E80A_PID 0xE80A
#define FTDI_GUDEADS_E80B_PID 0xE80B
#define FTDI_GUDEADS_E80C_PID 0xE80C
#define FTDI_GUDEADS_E80D_PID 0xE80D
#define FTDI_GUDEADS_E80E_PID 0xE80E
#define FTDI_GUDEADS_E80F_PID 0xE80F
#define FTDI_GUDEADS_E888_PID 0xE888 /* Expert ISDN Control USB */
#define FTDI_GUDEADS_E889_PID 0xE889 /* USB RS-232 OptoBridge */
#define FTDI_GUDEADS_E88A_PID 0xE88A
#define FTDI_GUDEADS_E88B_PID 0xE88B
#define FTDI_GUDEADS_E88C_PID 0xE88C
#define FTDI_GUDEADS_E88D_PID 0xE88D
#define FTDI_GUDEADS_E88E_PID 0xE88E
#define FTDI_GUDEADS_E88F_PID 0xE88F
/*
* Linx Technologies product ids
*/
#define LINX_SDMUSBQSS_PID 0xF448 /* Linx SDM-USB-QS-S */
#define LINX_MASTERDEVEL2_PID 0xF449 /* Linx Master Development 2.0 */
#define LINX_FUTURE_0_PID 0xF44A /* Linx future device */
#define LINX_FUTURE_1_PID 0xF44B /* Linx future device */
#define LINX_FUTURE_2_PID 0xF44C /* Linx future device */
/* CCS Inc. ICDU/ICDU40 product ID - the FT232BM is used in an in-circuit-debugger */
/* unit for PIC16's/PIC18's */
#define FTDI_CCSICDU20_0_PID 0xF9D0
#define FTDI_CCSICDU40_1_PID 0xF9D1
#define FTDI_CCSMACHX_2_PID 0xF9D2
/* Inside Accesso contactless reader (http://www.insidefr.com) */
#define INSIDE_ACCESSO 0xFAD0
/*
* Intrepid Control Systems (http://www.intrepidcs.com/) ValueCAN and NeoVI
*/
#define INTREPID_VID 0x093C
#define INTREPID_VALUECAN_PID 0x0601
#define INTREPID_NEOVI_PID 0x0701
/*
* Falcom Wireless Communications GmbH
*/
#define FALCOM_VID 0x0F94 /* Vendor Id */
#define FALCOM_TWIST_PID 0x0001 /* Falcom Twist USB GPRS modem */
#define FALCOM_SAMBA_PID 0x0005 /* Falcom Samba USB GPRS modem */
/*
* SUUNTO product ids
*/
#define FTDI_SUUNTO_SPORTS_PID 0xF680 /* Suunto Sports instrument */
/*
* Oceanic product ids
*/
#define FTDI_OCEANIC_PID 0xF460 /* Oceanic dive instrument */
/*
* TTi (Thurlby Thandar Instruments)
*/
#define TTI_VID 0x103E /* Vendor Id */
#define TTI_QL355P_PID 0x03E8 /* TTi QL355P power supply */
/*
* Definitions for B&B Electronics products.
*/
#define BANDB_VID 0x0856 /* B&B Electronics Vendor ID */
#define BANDB_USOTL4_PID 0xAC01 /* USOTL4 Isolated RS-485 Converter */
#define BANDB_USTL4_PID 0xAC02 /* USTL4 RS-485 Converter */
#define BANDB_USO9ML2_PID 0xAC03 /* USO9ML2 Isolated RS-232 Converter */
/*
* RM Michaelides CANview USB (http://www.rmcan.com)
* CAN fieldbus interface adapter, added by port GmbH www.port.de)
* Ian Abbott changed the macro names for consistency.
*/
#define FTDI_RM_CANVIEW_PID 0xfd60 /* Product Id */
/*
* EVER Eco Pro UPS (http://www.ever.com.pl/)
*/
#define EVER_ECO_PRO_CDS 0xe520 /* RS-232 converter */
/*
* 4N-GALAXY.DE PIDs for CAN-USB, USB-RS232, USB-RS422, USB-RS485,
* USB-TTY activ, USB-TTY passiv. Some PIDs are used by several devices
* and I'm not entirely sure which are used by which.
*/
#define FTDI_4N_GALAXY_DE_1_PID 0xF3C0
#define FTDI_4N_GALAXY_DE_2_PID 0xF3C1
/*
* Mobility Electronics products.
*/
#define MOBILITY_VID 0x1342
#define MOBILITY_USB_SERIAL_PID 0x0202 /* EasiDock USB 200 serial */
/*
* microHAM product IDs (http://www.microham.com).
* Submitted by Justin Burket (KL1RL) <zorton@jtan.com>
* and Mike Studer (K6EEP) <k6eep@hamsoftware.org>.
* Ian Abbott <abbotti@mev.co.uk> added a few more from the driver INF file.
*/
#define FTDI_MHAM_KW_PID 0xEEE8 /* USB-KW interface */
#define FTDI_MHAM_YS_PID 0xEEE9 /* USB-YS interface */
#define FTDI_MHAM_Y6_PID 0xEEEA /* USB-Y6 interface */
#define FTDI_MHAM_Y8_PID 0xEEEB /* USB-Y8 interface */
#define FTDI_MHAM_IC_PID 0xEEEC /* USB-IC interface */
#define FTDI_MHAM_DB9_PID 0xEEED /* USB-DB9 interface */
#define FTDI_MHAM_RS232_PID 0xEEEE /* USB-RS232 interface */
#define FTDI_MHAM_Y9_PID 0xEEEF /* USB-Y9 interface */
/*
* Active Robots product ids.
*/
#define FTDI_ACTIVE_ROBOTS_PID 0xE548 /* USB comms board */
/*
* Xsens Technologies BV products (http://www.xsens.com).
*/
#define XSENS_CONVERTER_0_PID 0xD388
#define XSENS_CONVERTER_1_PID 0xD389
#define XSENS_CONVERTER_2_PID 0xD38A
#define XSENS_CONVERTER_3_PID 0xD38B
#define XSENS_CONVERTER_4_PID 0xD38C
#define XSENS_CONVERTER_5_PID 0xD38D
#define XSENS_CONVERTER_6_PID 0xD38E
#define XSENS_CONVERTER_7_PID 0xD38F
/*
* Teratronik product ids.
* Submitted by O. Wölfelschneider.
*/
#define FTDI_TERATRONIK_VCP_PID 0xEC88 /* Teratronik device (preferring VCP driver on windows) */
#define FTDI_TERATRONIK_D2XX_PID 0xEC89 /* Teratronik device (preferring D2XX driver on windows) */
/*
* Evolution Robotics products (http://www.evolution.com/).
* Submitted by Shawn M. Lavelle.
*/
#define EVOLUTION_VID 0xDEEE /* Vendor ID */
#define EVOLUTION_ER1_PID 0x0300 /* ER1 Control Module */
#define EVO_8U232AM_PID 0x02FF /* Evolution robotics RCM2 (FT232AM)*/
#define EVO_HYBRID_PID 0x0302 /* Evolution robotics RCM4 PID (FT232BM)*/
#define EVO_RCM4_PID 0x0303 /* Evolution robotics RCM4 PID */
/* Pyramid Computer GmbH */
#define FTDI_PYRAMID_PID 0xE6C8 /* Pyramid Appliance Display */
/*
* Posiflex inc retail equipment (http://www.posiflex.com.tw)
*/
#define POSIFLEX_VID 0x0d3a /* Vendor ID */
#define POSIFLEX_PP7000_PID 0x0300 /* PP-7000II thermal printer */
/*
* Westrex International devices submitted by Cory Lee
*/
#define FTDI_WESTREX_MODEL_777_PID 0xDC00 /* Model 777 */
#define FTDI_WESTREX_MODEL_8900F_PID 0xDC01 /* Model 8900F */
/*
* RR-CirKits LocoBuffer USB (http://www.rr-cirkits.com)
*/
#define FTDI_RRCIRKITS_LOCOBUFFER_PID 0xc7d0 /* LocoBuffer USB */
/*
* Eclo (http://www.eclo.pt/) product IDs.
* PID 0xEA90 submitted by Martin Grill.
*/
#define FTDI_ECLO_COM_1WIRE_PID 0xEA90 /* COM to 1-Wire USB adaptor */
/*
* Papouch products (http://www.papouch.com/)
* Submitted by Folkert van Heusden
*/
#define PAPOUCH_VID 0x5050 /* Vendor ID */
#define PAPOUCH_TMU_PID 0x0400 /* TMU USB Thermometer */
#define PAPOUCH_QUIDO4x4_PID 0x0900 /* Quido 4/4 Module */
/*
* ACG Identification Technologies GmbH products (http://www.acg.de/).
* Submitted by anton -at- goto10 -dot- org.
*/
#define FTDI_ACG_HFDUAL_PID 0xDD20 /* HF Dual ISO Reader (RFID) */
/*
* Yost Engineering, Inc. products (www.yostengineering.com).
* PID 0xE050 submitted by Aaron Prose.
*/
#define FTDI_YEI_SERVOCENTER31_PID 0xE050 /* YEI ServoCenter3.1 USB */
/*
* ThorLabs USB motor drivers
*/
#define FTDI_THORLABS_PID 0xfaf0 /* ThorLabs USB motor drivers */
/*
* Testo products (http://www.testo.com/)
* Submitted by Colin Leroy
*/
#define TESTO_VID 0x128D
#define TESTO_USB_INTERFACE_PID 0x0001
/*
* Gamma Scout (http://gamma-scout.com/). Submitted by rsc@runtux.com.
*/
#define FTDI_GAMMA_SCOUT_PID 0xD678 /* Gamma Scout online */
/*
* Tactrix OpenPort (ECU) devices.
* OpenPort 1.3M submitted by Donour Sizemore.
* OpenPort 1.3S and 1.3U submitted by Ian Abbott.
*/
#define FTDI_TACTRIX_OPENPORT_13M_PID 0xCC48 /* OpenPort 1.3 Mitsubishi */
#define FTDI_TACTRIX_OPENPORT_13S_PID 0xCC49 /* OpenPort 1.3 Subaru */
#define FTDI_TACTRIX_OPENPORT_13U_PID 0xCC4A /* OpenPort 1.3 Universal */
/*
* Telldus Technologies
*/
#define TELLDUS_VID 0x1781 /* Vendor ID */
#define TELLDUS_TELLSTICK_PID 0x0C30 /* RF control dongle 433 MHz using FT232RL */
/*
* IBS elektronik product ids
* Submitted by Thomas Schleusener
*/
#define FTDI_IBS_US485_PID 0xff38 /* IBS US485 (USB<-->RS422/485 interface) */
#define FTDI_IBS_PICPRO_PID 0xff39 /* IBS PIC-Programmer */
#define FTDI_IBS_PCMCIA_PID 0xff3a /* IBS Card reader for PCMCIA SRAM-cards */
#define FTDI_IBS_PK1_PID 0xff3b /* IBS PK1 - Particel counter */
#define FTDI_IBS_RS232MON_PID 0xff3c /* IBS RS232 - Monitor */
#define FTDI_IBS_APP70_PID 0xff3d /* APP 70 (dust monitoring system) */
#define FTDI_IBS_PEDO_PID 0xff3e /* IBS PEDO-Modem (RF modem 868.35 MHz) */
#define FTDI_IBS_PROD_PID 0xff3f /* future device */
/*
* MaxStream devices www.maxstream.net
*/
#define FTDI_MAXSTREAM_PID 0xEE18 /* Xbee PKG-U Module */
/* Olimex */
#define OLIMEX_VID 0x15BA
#define OLIMEX_ARM_USB_OCD_PID 0x0003
/* Luminary Micro Stellaris Boards, VID = FTDI_VID */
/* FTDI 2332C Dual channel device, side A=245 FIFO (JTAG), Side B=RS232 UART */
#define LMI_LM3S_DEVEL_BOARD_PID 0xbcd8
#define LMI_LM3S_EVAL_BOARD_PID 0xbcd9
/* www.elsterelectricity.com Elster Unicom III Optical Probe */
#define FTDI_ELSTER_UNICOM_PID 0xE700 /* Product Id */
/*
* The Mobility Lab (TML)
* Submitted by Pierre Castella
*/
#define TML_VID 0x1B91 /* Vendor ID */
#define TML_USB_SERIAL_PID 0x0064 /* USB - Serial Converter */
/* NDI Polaris System */
#define FTDI_NDI_HUC_PID 0xDA70
/* Propox devices */
#define FTDI_PROPOX_JTAGCABLEII_PID 0xD738
/* Rig Expert Ukraine devices */
#define FTDI_REU_TINY_PID 0xED22 /* RigExpert Tiny */
/* Domintell products http://www.domintell.com */
#define FTDI_DOMINTELL_DGQG_PID 0xEF50 /* Master */
#define FTDI_DOMINTELL_DUSB_PID 0xEF51 /* DUSB01 module */
/* Alti-2 products http://www.alti-2.com */
#define ALTI2_VID 0x1BC9
#define ALTI2_N3_PID 0x6001 /* Neptune 3 */
/* Commands */
#define FTDI_SIO_RESET 0 /* Reset the port */
#define FTDI_SIO_MODEM_CTRL 1 /* Set the modem control register */
#define FTDI_SIO_SET_FLOW_CTRL 2 /* Set flow control register */
#define FTDI_SIO_SET_BAUD_RATE 3 /* Set baud rate */
#define FTDI_SIO_SET_DATA 4 /* Set the data characteristics of the port */
#define FTDI_SIO_GET_MODEM_STATUS 5 /* Retrieve current value of modern status register */
#define FTDI_SIO_SET_EVENT_CHAR 6 /* Set the event character */
#define FTDI_SIO_SET_ERROR_CHAR 7 /* Set the error character */
#define FTDI_SIO_SET_LATENCY_TIMER 9 /* Set the latency timer */
#define FTDI_SIO_GET_LATENCY_TIMER 10 /* Get the latency timer */
/* Interface indicies for FT2232, FT2232H and FT4232H devices*/
#define INTERFACE_A 1
#define INTERFACE_B 2
#define INTERFACE_C 3
#define INTERFACE_D 4
/*
* FIC / OpenMoko, Inc. http://wiki.openmoko.org/wiki/Neo1973_Debug_Board_v3
* Submitted by Harald Welte <laforge@openmoko.org>
*/
#define FIC_VID 0x1457
#define FIC_NEO1973_DEBUG_PID 0x5118
/*
* RATOC REX-USB60F
*/
#define RATOC_VENDOR_ID 0x0584
#define RATOC_PRODUCT_ID_USB60F 0xb020
/*
* DIEBOLD BCS SE923
*/
#define DIEBOLD_BCS_SE923_PID 0xfb99
/*
* Atmel STK541
*/
#define ATMEL_VID 0x03eb /* Vendor ID */
#define STK541_PID 0x2109 /* Zigbee Controller */
/*
* Dresden Elektronic Sensor Terminal Board
*/
#define DE_VID 0x1cf1 /* Vendor ID */
#define STB_PID 0x0001 /* Sensor Terminal Board */
#define WHT_PID 0x0004 /* Wireless Handheld Terminal */
/*
* Blackfin gnICE JTAG
* http://docs.blackfin.uclinux.org/doku.php?id=hw:jtag:gnice
*/
#define ADI_VID 0x0456
#define ADI_GNICE_PID 0xF000
/*
* JETI SPECTROMETER SPECBOS 1201
* http://www.jeti.com/products/sys/scb/scb1201.php
*/
#define JETI_VID 0x0c6c
#define JETI_SPC1201_PID 0x04b2
/*
* Marvell SheevaPlug
*/
#define MARVELL_VID 0x9e88
#define MARVELL_SHEEVAPLUG_PID 0x9e8f
/*
* BmRequestType: 1100 0000b
* bRequest: FTDI_E2_READ
* wValue: 0
* wIndex: Address of word to read
* wLength: 2
* Data: Will return a word of data from E2Address
*
*/
/* Port Identifier Table */
#define PIT_DEFAULT 0 /* SIOA */
#define PIT_SIOA 1 /* SIOA */
/* The device this driver is tested with one has only one port */
#define PIT_SIOB 2 /* SIOB */
#define PIT_PARALLEL 3 /* Parallel */
/* FTDI_SIO_RESET */
#define FTDI_SIO_RESET_REQUEST FTDI_SIO_RESET
#define FTDI_SIO_RESET_REQUEST_TYPE 0x40
#define FTDI_SIO_RESET_SIO 0
#define FTDI_SIO_RESET_PURGE_RX 1
#define FTDI_SIO_RESET_PURGE_TX 2
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_RESET
* wValue: Control Value
* 0 = Reset SIO
* 1 = Purge RX buffer
* 2 = Purge TX buffer
* wIndex: Port
* wLength: 0
* Data: None
*
* The Reset SIO command has this effect:
*
* Sets flow control set to 'none'
* Event char = $0D
* Event trigger = disabled
* Purge RX buffer
* Purge TX buffer
* Clear DTR
* Clear RTS
* baud and data format not reset
*
* The Purge RX and TX buffer commands affect nothing except the buffers
*
*/
/* FTDI_SIO_SET_BAUDRATE */
#define FTDI_SIO_SET_BAUDRATE_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_BAUDRATE_REQUEST 3
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_SET_BAUDRATE
* wValue: BaudDivisor value - see below
* wIndex: Port
* wLength: 0
* Data: None
* The BaudDivisor values are calculated as follows:
* - BaseClock is either 12000000 or 48000000 depending on the device. FIXME: I wish
* I knew how to detect old chips to select proper base clock!
* - BaudDivisor is a fixed point number encoded in a funny way.
* (--WRONG WAY OF THINKING--)
* BaudDivisor is a fixed point number encoded with following bit weighs:
* (-2)(-1)(13..0). It is a radical with a denominator of 4, so values
* end with 0.0 (00...), 0.25 (10...), 0.5 (01...), and 0.75 (11...).
* (--THE REALITY--)
* The both-bits-set has quite different meaning from 0.75 - the chip designers
* have decided it to mean 0.125 instead of 0.75.
* This info looked up in FTDI application note "FT8U232 DEVICES \ Data Rates
* and Flow Control Consideration for USB to RS232".
* - BaudDivisor = (BaseClock / 16) / BaudRate, where the (=) operation should
* automagically re-encode the resulting value to take fractions into consideration.
* As all values are integers, some bit twiddling is in order:
* BaudDivisor = (BaseClock / 16 / BaudRate) |
* (((BaseClock / 2 / BaudRate) & 4) ? 0x4000 // 0.5
* : ((BaseClock / 2 / BaudRate) & 2) ? 0x8000 // 0.25
* : ((BaseClock / 2 / BaudRate) & 1) ? 0xc000 // 0.125
* : 0)
*
* For the FT232BM, a 17th divisor bit was introduced to encode the multiples
* of 0.125 missing from the FT8U232AM. Bits 16 to 14 are coded as follows
* (the first four codes are the same as for the FT8U232AM, where bit 16 is
* always 0):
* 000 - add .000 to divisor
* 001 - add .500 to divisor
* 010 - add .250 to divisor
* 011 - add .125 to divisor
* 100 - add .375 to divisor
* 101 - add .625 to divisor
* 110 - add .750 to divisor
* 111 - add .875 to divisor
* Bits 15 to 0 of the 17-bit divisor are placed in the urb value. Bit 16 is
* placed in bit 0 of the urb index.
*
* Note that there are a couple of special cases to support the highest baud
* rates. If the calculated divisor value is 1, this needs to be replaced with
* 0. Additionally for the FT232BM, if the calculated divisor value is 0x4001
* (1.5), this needs to be replaced with 0x0001 (1) (but this divisor value is
* not supported by the FT8U232AM).
*/
typedef enum {
SIO = 1,
FT8U232AM = 2,
FT232BM = 3,
FT2232C = 4,
FT232RL = 5,
FT2232H = 6,
FT4232H = 7
} ftdi_chip_type_t;
typedef enum {
ftdi_sio_b300 = 0,
ftdi_sio_b600 = 1,
ftdi_sio_b1200 = 2,
ftdi_sio_b2400 = 3,
ftdi_sio_b4800 = 4,
ftdi_sio_b9600 = 5,
ftdi_sio_b19200 = 6,
ftdi_sio_b38400 = 7,
ftdi_sio_b57600 = 8,
ftdi_sio_b115200 = 9
} FTDI_SIO_baudrate_t;
/*
* The ftdi_8U232AM_xxMHz_byyy constants have been removed. The encoded divisor values
* are calculated internally.
*/
#define FTDI_SIO_SET_DATA_REQUEST FTDI_SIO_SET_DATA
#define FTDI_SIO_SET_DATA_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_DATA_PARITY_NONE (0x0 << 8)
#define FTDI_SIO_SET_DATA_PARITY_ODD (0x1 << 8)
#define FTDI_SIO_SET_DATA_PARITY_EVEN (0x2 << 8)
#define FTDI_SIO_SET_DATA_PARITY_MARK (0x3 << 8)
#define FTDI_SIO_SET_DATA_PARITY_SPACE (0x4 << 8)
#define FTDI_SIO_SET_DATA_STOP_BITS_1 (0x0 << 11)
#define FTDI_SIO_SET_DATA_STOP_BITS_15 (0x1 << 11)
#define FTDI_SIO_SET_DATA_STOP_BITS_2 (0x2 << 11)
#define FTDI_SIO_SET_BREAK (0x1 << 14)
/* FTDI_SIO_SET_DATA */
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_SET_DATA
* wValue: Data characteristics (see below)
* wIndex: Port
* wLength: 0
* Data: No
*
* Data characteristics
*
* B0..7 Number of data bits
* B8..10 Parity
* 0 = None
* 1 = Odd
* 2 = Even
* 3 = Mark
* 4 = Space
* B11..13 Stop Bits
* 0 = 1
* 1 = 1.5
* 2 = 2
* B14
* 1 = TX ON (break)
* 0 = TX OFF (normal state)
* B15 Reserved
*
*/
/* FTDI_SIO_MODEM_CTRL */
#define FTDI_SIO_SET_MODEM_CTRL_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_MODEM_CTRL_REQUEST FTDI_SIO_MODEM_CTRL
/*
* BmRequestType: 0100 0000B
* bRequest: FTDI_SIO_MODEM_CTRL
* wValue: ControlValue (see below)
* wIndex: Port
* wLength: 0
* Data: None
*
* NOTE: If the device is in RTS/CTS flow control, the RTS set by this
* command will be IGNORED without an error being returned
* Also - you can not set DTR and RTS with one control message
*/
#define FTDI_SIO_SET_DTR_MASK 0x1
#define FTDI_SIO_SET_DTR_HIGH (1 | (FTDI_SIO_SET_DTR_MASK << 8))
#define FTDI_SIO_SET_DTR_LOW (0 | (FTDI_SIO_SET_DTR_MASK << 8))
#define FTDI_SIO_SET_RTS_MASK 0x2
#define FTDI_SIO_SET_RTS_HIGH (2 | (FTDI_SIO_SET_RTS_MASK << 8))
#define FTDI_SIO_SET_RTS_LOW (0 | (FTDI_SIO_SET_RTS_MASK << 8))
/*
* ControlValue
* B0 DTR state
* 0 = reset
* 1 = set
* B1 RTS state
* 0 = reset
* 1 = set
* B2..7 Reserved
* B8 DTR state enable
* 0 = ignore
* 1 = use DTR state
* B9 RTS state enable
* 0 = ignore
* 1 = use RTS state
* B10..15 Reserved
*/
/* FTDI_SIO_SET_FLOW_CTRL */
#define FTDI_SIO_SET_FLOW_CTRL_REQUEST_TYPE 0x40
#define FTDI_SIO_SET_FLOW_CTRL_REQUEST FTDI_SIO_SET_FLOW_CTRL
#define FTDI_SIO_DISABLE_FLOW_CTRL 0x0
#define FTDI_SIO_RTS_CTS_HS (0x1 << 8)
#define FTDI_SIO_DTR_DSR_HS (0x2 << 8)
#define FTDI_SIO_XON_XOFF_HS (0x4 << 8)
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_FLOW_CTRL
* wValue: Xoff/Xon
* wIndex: Protocol/Port - hIndex is protocl / lIndex is port
* wLength: 0
* Data: None
*
* hIndex protocol is:
* B0 Output handshaking using RTS/CTS
* 0 = disabled
* 1 = enabled
* B1 Output handshaking using DTR/DSR
* 0 = disabled
* 1 = enabled
* B2 Xon/Xoff handshaking
* 0 = disabled
* 1 = enabled
*
* A value of zero in the hIndex field disables handshaking
*
* If Xon/Xoff handshaking is specified, the hValue field should contain the XOFF character
* and the lValue field contains the XON character.
*/
/*
* FTDI_SIO_GET_LATENCY_TIMER
*
* Set the timeout interval. The FTDI collects data from the slave
* device, transmitting it to the host when either A) 62 bytes are
* received, or B) the timeout interval has elapsed and the buffer
* contains at least 1 byte. Setting this value to a small number
* can dramatically improve performance for applications which send
* small packets, since the default value is 16ms.
*/
#define FTDI_SIO_GET_LATENCY_TIMER_REQUEST FTDI_SIO_GET_LATENCY_TIMER
#define FTDI_SIO_GET_LATENCY_TIMER_REQUEST_TYPE 0xC0
/*
* BmRequestType: 1100 0000b
* bRequest: FTDI_SIO_GET_LATENCY_TIMER
* wValue: 0
* wIndex: Port
* wLength: 0
* Data: latency (on return)
*/
/*
* FTDI_SIO_SET_LATENCY_TIMER
*
* Set the timeout interval. The FTDI collects data from the slave
* device, transmitting it to the host when either A) 62 bytes are
* received, or B) the timeout interval has elapsed and the buffer
* contains at least 1 byte. Setting this value to a small number
* can dramatically improve performance for applications which send
* small packets, since the default value is 16ms.
*/
#define FTDI_SIO_SET_LATENCY_TIMER_REQUEST FTDI_SIO_SET_LATENCY_TIMER
#define FTDI_SIO_SET_LATENCY_TIMER_REQUEST_TYPE 0x40
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_LATENCY_TIMER
* wValue: Latency (milliseconds)
* wIndex: Port
* wLength: 0
* Data: None
*
* wValue:
* B0..7 Latency timer
* B8..15 0
*
*/
/*
* FTDI_SIO_SET_EVENT_CHAR
*
* Set the special event character for the specified communications port.
* If the device sees this character it will immediately return the
* data read so far - rather than wait 40ms or until 62 bytes are read
* which is what normally happens.
*/
#define FTDI_SIO_SET_EVENT_CHAR_REQUEST FTDI_SIO_SET_EVENT_CHAR
#define FTDI_SIO_SET_EVENT_CHAR_REQUEST_TYPE 0x40
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_EVENT_CHAR
* wValue: EventChar
* wIndex: Port
* wLength: 0
* Data: None
*
* wValue:
* B0..7 Event Character
* B8 Event Character Processing
* 0 = disabled
* 1 = enabled
* B9..15 Reserved
*
*/
/* FTDI_SIO_SET_ERROR_CHAR */
/* Set the parity error replacement character for the specified communications port */
/*
* BmRequestType: 0100 0000b
* bRequest: FTDI_SIO_SET_EVENT_CHAR
* wValue: Error Char
* wIndex: Port
* wLength: 0
* Data: None
*
*Error Char
* B0..7 Error Character
* B8 Error Character Processing
* 0 = disabled
* 1 = enabled
* B9..15 Reserved
*
*/
/* FTDI_SIO_GET_MODEM_STATUS */
/* Retrieve the current value of the modem status register */
#define FTDI_SIO_GET_MODEM_STATUS_REQUEST_TYPE 0xc0
#define FTDI_SIO_GET_MODEM_STATUS_REQUEST FTDI_SIO_GET_MODEM_STATUS
#define FTDI_SIO_CTS_MASK 0x10
#define FTDI_SIO_DSR_MASK 0x20
#define FTDI_SIO_RI_MASK 0x40
#define FTDI_SIO_RLSD_MASK 0x80
/*
* BmRequestType: 1100 0000b
* bRequest: FTDI_SIO_GET_MODEM_STATUS
* wValue: zero
* wIndex: Port
* wLength: 1
* Data: Status
*
* One byte of data is returned
* B0..3 0
* B4 CTS
* 0 = inactive
* 1 = active
* B5 DSR
* 0 = inactive
* 1 = active
* B6 Ring Indicator (RI)
* 0 = inactive
* 1 = active
* B7 Receive Line Signal Detect (RLSD)
* 0 = inactive
* 1 = active
*/
/* Descriptors returned by the device
*
* Device Descriptor
*
* Offset Field Size Value Description
* 0 bLength 1 0x12 Size of descriptor in bytes
* 1 bDescriptorType 1 0x01 DEVICE Descriptor Type
* 2 bcdUSB 2 0x0110 USB Spec Release Number
* 4 bDeviceClass 1 0x00 Class Code
* 5 bDeviceSubClass 1 0x00 SubClass Code
* 6 bDeviceProtocol 1 0x00 Protocol Code
* 7 bMaxPacketSize0 1 0x08 Maximum packet size for endpoint 0
* 8 idVendor 2 0x0403 Vendor ID
* 10 idProduct 2 0x8372 Product ID (FTDI_SIO_PID)
* 12 bcdDevice 2 0x0001 Device release number
* 14 iManufacturer 1 0x01 Index of man. string desc
* 15 iProduct 1 0x02 Index of prod string desc
* 16 iSerialNumber 1 0x02 Index of serial nmr string desc
* 17 bNumConfigurations 1 0x01 Number of possible configurations
*
* Configuration Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x09 Size of descriptor in bytes
* 1 bDescriptorType 1 0x02 CONFIGURATION Descriptor Type
* 2 wTotalLength 2 0x0020 Total length of data
* 4 bNumInterfaces 1 0x01 Number of interfaces supported
* 5 bConfigurationValue 1 0x01 Argument for SetCOnfiguration() req
* 6 iConfiguration 1 0x02 Index of config string descriptor
* 7 bmAttributes 1 0x20 Config characteristics Remote Wakeup
* 8 MaxPower 1 0x1E Max power consumption
*
* Interface Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x09 Size of descriptor in bytes
* 1 bDescriptorType 1 0x04 INTERFACE Descriptor Type
* 2 bInterfaceNumber 1 0x00 Number of interface
* 3 bAlternateSetting 1 0x00 Value used to select alternate
* 4 bNumEndpoints 1 0x02 Number of endpoints
* 5 bInterfaceClass 1 0xFF Class Code
* 6 bInterfaceSubClass 1 0xFF Subclass Code
* 7 bInterfaceProtocol 1 0xFF Protocol Code
* 8 iInterface 1 0x02 Index of interface string description
*
* IN Endpoint Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x07 Size of descriptor in bytes
* 1 bDescriptorType 1 0x05 ENDPOINT descriptor type
* 2 bEndpointAddress 1 0x82 Address of endpoint
* 3 bmAttributes 1 0x02 Endpoint attributes - Bulk
* 4 bNumEndpoints 2 0x0040 maximum packet size
* 5 bInterval 1 0x00 Interval for polling endpoint
*
* OUT Endpoint Descriptor
*
* Offset Field Size Value
* 0 bLength 1 0x07 Size of descriptor in bytes
* 1 bDescriptorType 1 0x05 ENDPOINT descriptor type
* 2 bEndpointAddress 1 0x02 Address of endpoint
* 3 bmAttributes 1 0x02 Endpoint attributes - Bulk
* 4 bNumEndpoints 2 0x0040 maximum packet size
* 5 bInterval 1 0x00 Interval for polling endpoint
*
* DATA FORMAT
*
* IN Endpoint
*
* The device reserves the first two bytes of data on this endpoint to contain the current
* values of the modem and line status registers. In the absence of data, the device
* generates a message consisting of these two status bytes every 40 ms
*
* Byte 0: Modem Status
*
* Offset Description
* B0 Reserved - must be 1
* B1 Reserved - must be 0
* B2 Reserved - must be 0
* B3 Reserved - must be 0
* B4 Clear to Send (CTS)
* B5 Data Set Ready (DSR)
* B6 Ring Indicator (RI)
* B7 Receive Line Signal Detect (RLSD)
*
* Byte 1: Line Status
*
* Offset Description
* B0 Data Ready (DR)
* B1 Overrun Error (OE)
* B2 Parity Error (PE)
* B3 Framing Error (FE)
* B4 Break Interrupt (BI)
* B5 Transmitter Holding Register (THRE)
* B6 Transmitter Empty (TEMT)
* B7 Error in RCVR FIFO
*
*/
#define FTDI_RS0_CTS (1 << 4)
#define FTDI_RS0_DSR (1 << 5)
#define FTDI_RS0_RI (1 << 6)
#define FTDI_RS0_RLSD (1 << 7)
#define FTDI_RS_DR 1
#define FTDI_RS_OE (1<<1)
#define FTDI_RS_PE (1<<2)
#define FTDI_RS_FE (1<<3)
#define FTDI_RS_BI (1<<4)
#define FTDI_RS_THRE (1<<5)
#define FTDI_RS_TEMT (1<<6)
#define FTDI_RS_FIFO (1<<7)
/*
* OUT Endpoint
*
* This device reserves the first bytes of data on this endpoint contain the length
* and port identifier of the message. For the FTDI USB Serial converter the port
* identifier is always 1.
*
* Byte 0: Line Status
*
* Offset Description
* B0 Reserved - must be 1
* B1 Reserved - must be 0
* B2..7 Length of message - (not including Byte 0)
*
*/
View Git Blame Copy Permalink