7f7f4ea15e
STMPE801 is a GPIO expander. Registers for 801 are much different from other variants. This patch adds support for STMPE801 in stmpe mfd driver. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
151 lines
3.2 KiB
C
151 lines
3.2 KiB
C
/*
|
|
* ST Microelectronics MFD: stmpe's spi client specific driver
|
|
*
|
|
* Copyright (C) ST Microelectronics SA 2011
|
|
*
|
|
* License Terms: GNU General Public License, version 2
|
|
* Author: Viresh Kumar <viresh.kumar@st.com> for ST Microelectronics
|
|
*/
|
|
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/kernel.h>
|
|
#include <linux/module.h>
|
|
#include <linux/types.h>
|
|
#include "stmpe.h"
|
|
|
|
#define READ_CMD (1 << 7)
|
|
|
|
static int spi_reg_read(struct stmpe *stmpe, u8 reg)
|
|
{
|
|
struct spi_device *spi = stmpe->client;
|
|
int status = spi_w8r16(spi, reg | READ_CMD);
|
|
|
|
return (status < 0) ? status : status >> 8;
|
|
}
|
|
|
|
static int spi_reg_write(struct stmpe *stmpe, u8 reg, u8 val)
|
|
{
|
|
struct spi_device *spi = stmpe->client;
|
|
u16 cmd = (val << 8) | reg;
|
|
|
|
return spi_write(spi, (const u8 *)&cmd, 2);
|
|
}
|
|
|
|
static int spi_block_read(struct stmpe *stmpe, u8 reg, u8 length, u8 *values)
|
|
{
|
|
int ret, i;
|
|
|
|
for (i = 0; i < length; i++) {
|
|
ret = spi_reg_read(stmpe, reg + i);
|
|
if (ret < 0)
|
|
return ret;
|
|
*(values + i) = ret;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int spi_block_write(struct stmpe *stmpe, u8 reg, u8 length,
|
|
const u8 *values)
|
|
{
|
|
int ret = 0, i;
|
|
|
|
for (i = length; i > 0; i--, reg++) {
|
|
ret = spi_reg_write(stmpe, reg, *(values + i - 1));
|
|
if (ret < 0)
|
|
return ret;
|
|
}
|
|
|
|
return ret;
|
|
}
|
|
|
|
static void spi_init(struct stmpe *stmpe)
|
|
{
|
|
struct spi_device *spi = stmpe->client;
|
|
|
|
spi->bits_per_word = 8;
|
|
|
|
/* This register is only present for stmpe811 */
|
|
if (stmpe->variant->id_val == 0x0811)
|
|
spi_reg_write(stmpe, STMPE811_REG_SPI_CFG, spi->mode);
|
|
|
|
if (spi_setup(spi) < 0)
|
|
dev_dbg(&spi->dev, "spi_setup failed\n");
|
|
}
|
|
|
|
static struct stmpe_client_info spi_ci = {
|
|
.read_byte = spi_reg_read,
|
|
.write_byte = spi_reg_write,
|
|
.read_block = spi_block_read,
|
|
.write_block = spi_block_write,
|
|
.init = spi_init,
|
|
};
|
|
|
|
static int __devinit
|
|
stmpe_spi_probe(struct spi_device *spi)
|
|
{
|
|
const struct spi_device_id *id = spi_get_device_id(spi);
|
|
|
|
/* don't exceed max specified rate - 1MHz - Limitation of STMPE */
|
|
if (spi->max_speed_hz > 1000000) {
|
|
dev_dbg(&spi->dev, "f(sample) %d KHz?\n",
|
|
(spi->max_speed_hz/1000));
|
|
return -EINVAL;
|
|
}
|
|
|
|
spi_ci.irq = spi->irq;
|
|
spi_ci.client = spi;
|
|
spi_ci.dev = &spi->dev;
|
|
|
|
return stmpe_probe(&spi_ci, id->driver_data);
|
|
}
|
|
|
|
static int __devexit stmpe_spi_remove(struct spi_device *spi)
|
|
{
|
|
struct stmpe *stmpe = dev_get_drvdata(&spi->dev);
|
|
|
|
return stmpe_remove(stmpe);
|
|
}
|
|
|
|
static const struct spi_device_id stmpe_spi_id[] = {
|
|
{ "stmpe610", STMPE610 },
|
|
{ "stmpe801", STMPE801 },
|
|
{ "stmpe811", STMPE811 },
|
|
{ "stmpe1601", STMPE1601 },
|
|
{ "stmpe2401", STMPE2401 },
|
|
{ "stmpe2403", STMPE2403 },
|
|
{ }
|
|
};
|
|
MODULE_DEVICE_TABLE(spi, stmpe_id);
|
|
|
|
static struct spi_driver stmpe_spi_driver = {
|
|
.driver = {
|
|
.name = "stmpe-spi",
|
|
.bus = &spi_bus_type,
|
|
.owner = THIS_MODULE,
|
|
#ifdef CONFIG_PM
|
|
.pm = &stmpe_dev_pm_ops,
|
|
#endif
|
|
},
|
|
.probe = stmpe_spi_probe,
|
|
.remove = __devexit_p(stmpe_spi_remove),
|
|
.id_table = stmpe_spi_id,
|
|
};
|
|
|
|
static int __init stmpe_init(void)
|
|
{
|
|
return spi_register_driver(&stmpe_spi_driver);
|
|
}
|
|
subsys_initcall(stmpe_init);
|
|
|
|
static void __exit stmpe_exit(void)
|
|
{
|
|
spi_unregister_driver(&stmpe_spi_driver);
|
|
}
|
|
module_exit(stmpe_exit);
|
|
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_DESCRIPTION("STMPE MFD SPI Interface Driver");
|
|
MODULE_AUTHOR("Viresh Kumar <viresh.kumar@st.com>");
|