kevin/linux
1
Fork 0
Code
124d255382
linux/drivers/usb/serial/ipw.c
Alan Cox a108bfcb37 USB: tty: Prune uses of tty_request_room in the USB layer 
We have lots of callers that do not need to do this in the first place.
Remove the calls as they both cost CPU and for big buffers can mess up the
multi-page allocation avoidance.

Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:55:12 -08:00

504 lines
13 KiB
C
Raw Blame History

/*
* IPWireless 3G UMTS TDD Modem driver (USB connected)
*
* Copyright (C) 2004 Roelf Diedericks <roelfd@inet.co.za>
* Copyright (C) 2004 Greg Kroah-Hartman <greg@kroah.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* All information about the device was acquired using SnoopyPro
* on MSFT's O/S, and examing the MSFT drivers' debug output
* (insanely left _on_ in the enduser version)
*
* It was written out of frustration with the IPWireless USB modem
* supplied by Axity3G/Sentech South Africa not supporting
* Linux whatsoever.
*
* Nobody provided any proprietary information that was not already
* available for this device.
*
* The modem adheres to the "3GPP TS 27.007 AT command set for 3G
* User Equipment (UE)" standard, available from
* http://www.3gpp.org/ftp/Specs/html-info/27007.htm
*
* The code was only tested the IPWireless handheld modem distributed
* in South Africa by Sentech.
*
* It may work for Woosh Inc in .nz too, as it appears they use the
* same kit.
*
* There is still some work to be done in terms of handling
* DCD, DTR, RTS, CTS which are currently faked.
* It's good enough for PPP at this point. It's based off all kinds of
* code found in usb/serial and usb/class
*
*/
#include <linux/kernel.h>
#include <linux/errno.h>
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/tty.h>
#include <linux/tty_flip.h>
#include <linux/module.h>
#include <linux/spinlock.h>
#include <linux/usb.h>
#include <linux/usb/serial.h>
#include <linux/uaccess.h>
/*
* Version Information
*/
#define DRIVER_VERSION "v0.3"
#define DRIVER_AUTHOR "Roelf Diedericks"
#define DRIVER_DESC "IPWireless tty driver"
#define IPW_TTY_MAJOR 240 /* real device node major id, experimental range */
#define IPW_TTY_MINORS 256 /* we support 256 devices, dunno why, it'd be insane :) */
#define USB_IPW_MAGIC 0x6d02 /* magic number for ipw struct */
/* Message sizes */
#define EVENT_BUFFER_SIZE 0xFF
#define CHAR2INT16(c1, c0) (((u32)((c1) & 0xff) << 8) + (u32)((c0) & 0xff))
#define NUM_BULK_URBS 24
#define NUM_CONTROL_URBS 16
/* vendor/product pairs that are known work with this driver*/
#define IPW_VID 0x0bc3
#define IPW_PID 0x0001
/* Vendor commands: */
/* baud rates */
enum {
ipw_sio_b256000 = 0x000e,
ipw_sio_b128000 = 0x001d,
ipw_sio_b115200 = 0x0020,
ipw_sio_b57600 = 0x0040,
ipw_sio_b56000 = 0x0042,
ipw_sio_b38400 = 0x0060,
ipw_sio_b19200 = 0x00c0,
ipw_sio_b14400 = 0x0100,
ipw_sio_b9600 = 0x0180,
ipw_sio_b4800 = 0x0300,
ipw_sio_b2400 = 0x0600,
ipw_sio_b1200 = 0x0c00,
ipw_sio_b600 = 0x1800
};
/* data bits */
#define ipw_dtb_7 0x700
#define ipw_dtb_8 0x810 /* ok so the define is misleading, I know, but forces 8,n,1 */
/* I mean, is there a point to any other setting these days? :) */
/* usb control request types : */
#define IPW_SIO_RXCTL 0x00 /* control bulk rx channel transmissions, value=1/0 (on/off) */
#define IPW_SIO_SET_BAUD 0x01 /* set baud, value=requested ipw_sio_bxxxx */
#define IPW_SIO_SET_LINE 0x03 /* set databits, parity. value=ipw_dtb_x */
#define IPW_SIO_SET_PIN 0x03 /* set/clear dtr/rts value=ipw_pin_xxx */
#define IPW_SIO_POLL 0x08 /* get serial port status byte, call with value=0 */
#define IPW_SIO_INIT 0x11 /* initializes ? value=0 (appears as first thing todo on open) */
#define IPW_SIO_PURGE 0x12 /* purge all transmissions?, call with value=numchar_to_purge */
#define IPW_SIO_HANDFLOW 0x13 /* set xon/xoff limits value=0, and a buffer of 0x10 bytes */
#define IPW_SIO_SETCHARS 0x13 /* set the flowcontrol special chars, value=0, buf=6 bytes, */
/* last 2 bytes contain flowcontrol chars e.g. 00 00 00 00 11 13 */
/* values used for request IPW_SIO_SET_PIN */
#define IPW_PIN_SETDTR 0x101
#define IPW_PIN_SETRTS 0x202
#define IPW_PIN_CLRDTR 0x100
#define IPW_PIN_CLRRTS 0x200 /* unconfirmed */
/* values used for request IPW_SIO_RXCTL */
#define IPW_RXBULK_ON 1
#define IPW_RXBULK_OFF 0
/* various 16 byte hardcoded transferbuffers used by flow control */
#define IPW_BYTES_FLOWINIT { 0x01, 0, 0, 0, 0x40, 0, 0, 0, \
0, 0, 0, 0, 0, 0, 0, 0 }
/* Interpretation of modem status lines */
/* These need sorting out by individually connecting pins and checking
* results. FIXME!
* When data is being sent we see 0x30 in the lower byte; this must
* contain DSR and CTS ...
*/
#define IPW_DSR ((1<<4) | (1<<5))
#define IPW_CTS ((1<<5) | (1<<4))
#define IPW_WANTS_TO_SEND 0x30
static const struct usb_device_id usb_ipw_ids[] = {
{ USB_DEVICE(IPW_VID, IPW_PID) },
{ },
};
MODULE_DEVICE_TABLE(usb, usb_ipw_ids);
static struct usb_driver usb_ipw_driver = {
.name = "ipwtty",
.probe = usb_serial_probe,
.disconnect = usb_serial_disconnect,
.id_table = usb_ipw_ids,
.no_dynamic_id = 1,
};
static int debug;
static void ipw_read_bulk_callback(struct urb *urb)
{
struct usb_serial_port *port = urb->context;
unsigned char *data = urb->transfer_buffer;
struct tty_struct *tty;
int result;
int status = urb->status;
dbg("%s - port %d", __func__, port->number);
if (status) {
dbg("%s - nonzero read bulk status received: %d",
__func__, status);
return;
}
usb_serial_debug_data(debug, &port->dev, __func__,
urb->actual_length, data);
tty = tty_port_tty_get(&port->port);
if (tty && urb->actual_length) {
tty_insert_flip_string(tty, data, urb->actual_length);
tty_flip_buffer_push(tty);
}
tty_kref_put(tty);
/* Continue trying to always read */
usb_fill_bulk_urb(port->read_urb, port->serial->dev,
usb_rcvbulkpipe(port->serial->dev,
port->bulk_in_endpointAddress),
port->read_urb->transfer_buffer,
port->read_urb->transfer_buffer_length,
ipw_read_bulk_callback, port);
result = usb_submit_urb(port->read_urb, GFP_ATOMIC);
if (result)
dev_err(&port->dev,
"%s - failed resubmitting read urb, error %d\n",
__func__, result);
return;
}
static int ipw_open(struct tty_struct *tty, struct usb_serial_port *port)
{
struct usb_device *dev = port->serial->dev;
u8 buf_flow_static[16] = IPW_BYTES_FLOWINIT;
u8 *buf_flow_init;
int result;
dbg("%s", __func__);
buf_flow_init = kmemdup(buf_flow_static, 16, GFP_KERNEL);
if (!buf_flow_init)
return -ENOMEM;
/* --1: Tell the modem to initialize (we think) From sniffs this is
* always the first thing that gets sent to the modem during
* opening of the device */
dbg("%s: Sending SIO_INIT (we guess)", __func__);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_INIT,
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
0,
0, /* index */
NULL,
0,
100000);
if (result < 0)
dev_err(&port->dev,
"Init of modem failed (error = %d)\n", result);
/* reset the bulk pipes */
usb_clear_halt(dev,
usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress));
usb_clear_halt(dev,
usb_sndbulkpipe(dev, port->bulk_out_endpointAddress));
/*--2: Start reading from the device */
dbg("%s: setting up bulk read callback", __func__);
usb_fill_bulk_urb(port->read_urb, dev,
usb_rcvbulkpipe(dev, port->bulk_in_endpointAddress),
port->bulk_in_buffer,
port->bulk_in_size,
ipw_read_bulk_callback, port);
result = usb_submit_urb(port->read_urb, GFP_KERNEL);
if (result < 0)
dbg("%s - usb_submit_urb(read bulk) failed with status %d",
__func__, result);
/*--3: Tell the modem to open the floodgates on the rx bulk channel */
dbg("%s:asking modem for RxRead (RXBULK_ON)", __func__);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_RXCTL,
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
IPW_RXBULK_ON,
0, /* index */
NULL,
0,
100000);
if (result < 0)
dev_err(&port->dev,
"Enabling bulk RxRead failed (error = %d)\n", result);
/*--4: setup the initial flowcontrol */
dbg("%s:setting init flowcontrol (%s)", __func__, buf_flow_init);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_HANDFLOW,
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
0,
0,
buf_flow_init,
0x10,
200000);
if (result < 0)
dev_err(&port->dev,
"initial flowcontrol failed (error = %d)\n", result);
/*--5: raise the dtr */
dbg("%s:raising dtr", __func__);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_SET_PIN,
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
IPW_PIN_SETDTR,
0,
NULL,
0,
200000);
if (result < 0)
dev_err(&port->dev,
"setting dtr failed (error = %d)\n", result);
/*--6: raise the rts */
dbg("%s:raising rts", __func__);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_SET_PIN,
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
IPW_PIN_SETRTS,
0,
NULL,
0,
200000);
if (result < 0)
dev_err(&port->dev,
"setting dtr failed (error = %d)\n", result);
kfree(buf_flow_init);
return 0;
}
static void ipw_dtr_rts(struct usb_serial_port *port, int on)
{
struct usb_device *dev = port->serial->dev;
int result;
/*--1: drop the dtr */
dbg("%s:dropping dtr", __func__);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_SET_PIN,
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
on ? IPW_PIN_SETDTR : IPW_PIN_CLRDTR,
0,
NULL,
0,
200000);
if (result < 0)
dev_err(&port->dev, "dropping dtr failed (error = %d)\n",
result);
/*--2: drop the rts */
dbg("%s:dropping rts", __func__);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_SET_PIN, USB_TYPE_VENDOR |
USB_RECIP_INTERFACE | USB_DIR_OUT,
on ? IPW_PIN_SETRTS : IPW_PIN_CLRRTS,
0,
NULL,
0,
200000);
if (result < 0)
dev_err(&port->dev,
"dropping rts failed (error = %d)\n", result);
}
static void ipw_close(struct usb_serial_port *port)
{
struct usb_device *dev = port->serial->dev;
int result;
/*--3: purge */
dbg("%s:sending purge", __func__);
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_PURGE, USB_TYPE_VENDOR |
USB_RECIP_INTERFACE | USB_DIR_OUT,
0x03,
0,
NULL,
0,
200000);
if (result < 0)
dev_err(&port->dev, "purge failed (error = %d)\n", result);
/* send RXBULK_off (tell modem to stop transmitting bulk data on
rx chan) */
result = usb_control_msg(dev, usb_sndctrlpipe(dev, 0),
IPW_SIO_RXCTL,
USB_TYPE_VENDOR | USB_RECIP_INTERFACE | USB_DIR_OUT,
IPW_RXBULK_OFF,
0, /* index */
NULL,
0,
100000);
if (result < 0)
dev_err(&port->dev,
"Disabling bulk RxRead failed (error = %d)\n", result);
/* shutdown any in-flight urbs that we know about */
usb_kill_urb(port->read_urb);
usb_kill_urb(port->write_urb);
}
static void ipw_write_bulk_callback(struct urb *urb)
{
struct usb_serial_port *port = urb->context;
int status = urb->status;
dbg("%s", __func__);
port->write_urb_busy = 0;
if (status)
dbg("%s - nonzero write bulk status received: %d",
__func__, status);
usb_serial_port_softint(port);
}
static int ipw_write(struct tty_struct *tty, struct usb_serial_port *port,
const unsigned char *buf, int count)
{
struct usb_device *dev = port->serial->dev;
int ret;
dbg("%s: TOP: count=%d, in_interrupt=%ld", __func__,
count, in_interrupt());
if (count == 0) {
dbg("%s - write request of 0 bytes", __func__);
return 0;
}
spin_lock_bh(&port->lock);
if (port->write_urb_busy) {
spin_unlock_bh(&port->lock);
dbg("%s - already writing", __func__);
return 0;
}
port->write_urb_busy = 1;
spin_unlock_bh(&port->lock);
count = min(count, port->bulk_out_size);
memcpy(port->bulk_out_buffer, buf, count);
dbg("%s count now:%d", __func__, count);
usb_fill_bulk_urb(port->write_urb, dev,
usb_sndbulkpipe(dev, port->bulk_out_endpointAddress),
port->write_urb->transfer_buffer,
count,
ipw_write_bulk_callback,
port);
ret = usb_submit_urb(port->write_urb, GFP_ATOMIC);
if (ret != 0) {
port->write_urb_busy = 0;
dbg("%s - usb_submit_urb(write bulk) failed with error = %d",
__func__, ret);
return ret;
}
dbg("%s returning %d", __func__, count);
return count;
}
static int ipw_probe(struct usb_serial_port *port)
{
return 0;
}
static int ipw_disconnect(struct usb_serial_port *port)
{
usb_set_serial_port_data(port, NULL);
return 0;
}
static struct usb_serial_driver ipw_device = {
.driver = {
.owner = THIS_MODULE,
.name = "ipw",
},
.description = "IPWireless converter",
.usb_driver = &usb_ipw_driver,
.id_table = usb_ipw_ids,
.num_ports = 1,
.open = ipw_open,
.close = ipw_close,
.dtr_rts = ipw_dtr_rts,
.port_probe = ipw_probe,
.port_remove = ipw_disconnect,
.write = ipw_write,
.write_bulk_callback = ipw_write_bulk_callback,
.read_bulk_callback = ipw_read_bulk_callback,
};
static int __init usb_ipw_init(void)
{
int retval;
retval = usb_serial_register(&ipw_device);
if (retval)
return retval;
retval = usb_register(&usb_ipw_driver);
if (retval) {
usb_serial_deregister(&ipw_device);
return retval;
}
printk(KERN_INFO KBUILD_MODNAME ": " DRIVER_VERSION ":"
DRIVER_DESC "\n");
return 0;
}
static void __exit usb_ipw_exit(void)
{
usb_deregister(&usb_ipw_driver);
usb_serial_deregister(&ipw_device);
}
module_init(usb_ipw_init);
module_exit(usb_ipw_exit);
/* Module information */
MODULE_AUTHOR(DRIVER_AUTHOR);
MODULE_DESCRIPTION(DRIVER_DESC);
MODULE_LICENSE("GPL");
module_param(debug, bool, S_IRUGO | S_IWUSR);
MODULE_PARM_DESC(debug, "Debug enabled or not");
View Git Blame Copy Permalink