0c0382e32d
This patch (as580) is perhaps the only result from the long discussion I had with David about his changes to the root-hub suspend/resume code. It renames the hub_suspend and hub_resume methods in struct usb_hcd to bus_suspend and bus_resume. These are more descriptive names, since the methods really do suspend or resume an entire USB bus, and less likely to be confused with the hub_suspend and hub_resume routines in hub.c. It also takes David's advice about removing the layer of bus glue, where those methods are called. And it implements a related change that David made to the other HCDs but forgot to put into dummy_hcd. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
415 lines
11 KiB
C
415 lines
11 KiB
C
/*
|
|
* EHCI HCD (Host Controller Driver) PCI Bus Glue.
|
|
*
|
|
* Copyright (c) 2000-2004 by David Brownell
|
|
*
|
|
* This program is free software; you can redistribute it and/or modify it
|
|
* under the terms of the GNU General Public License as published by the
|
|
* Free Software Foundation; either version 2 of the License, or (at your
|
|
* option) any later version.
|
|
*
|
|
* This program is distributed in the hope that it will be useful, but
|
|
* WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY
|
|
* or FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
|
|
* for more details.
|
|
*
|
|
* You should have received a copy of the GNU General Public License
|
|
* along with this program; if not, write to the Free Software Foundation,
|
|
* Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
|
|
*/
|
|
|
|
#ifndef CONFIG_PCI
|
|
#error "This file is PCI bus glue. CONFIG_PCI must be defined."
|
|
#endif
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
/* EHCI 0.96 (and later) section 5.1 says how to kick BIOS/SMM/...
|
|
* off the controller (maybe it can boot from highspeed USB disks).
|
|
*/
|
|
static int bios_handoff (struct ehci_hcd *ehci, int where, u32 cap)
|
|
{
|
|
struct pci_dev *pdev = to_pci_dev(ehci_to_hcd(ehci)->self.controller);
|
|
|
|
/* always say Linux will own the hardware */
|
|
pci_write_config_byte(pdev, where + 3, 1);
|
|
|
|
/* maybe wait a while for BIOS to respond */
|
|
if (cap & (1 << 16)) {
|
|
int msec = 5000;
|
|
|
|
do {
|
|
msleep(10);
|
|
msec -= 10;
|
|
pci_read_config_dword(pdev, where, &cap);
|
|
} while ((cap & (1 << 16)) && msec);
|
|
if (cap & (1 << 16)) {
|
|
ehci_err(ehci, "BIOS handoff failed (%d, %08x)\n",
|
|
where, cap);
|
|
// some BIOS versions seem buggy...
|
|
// return 1;
|
|
ehci_warn (ehci, "continuing after BIOS bug...\n");
|
|
/* disable all SMIs, and clear "BIOS owns" flag */
|
|
pci_write_config_dword(pdev, where + 4, 0);
|
|
pci_write_config_byte(pdev, where + 2, 0);
|
|
} else
|
|
ehci_dbg(ehci, "BIOS handoff succeeded\n");
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
/* called by khubd or root hub init threads */
|
|
static int ehci_pci_reset (struct usb_hcd *hcd)
|
|
{
|
|
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
|
|
u32 temp;
|
|
unsigned count = 256/4;
|
|
|
|
spin_lock_init (&ehci->lock);
|
|
|
|
ehci->caps = hcd->regs;
|
|
ehci->regs = hcd->regs + HC_LENGTH (readl (&ehci->caps->hc_capbase));
|
|
dbg_hcs_params (ehci, "reset");
|
|
dbg_hcc_params (ehci, "reset");
|
|
|
|
/* cache this readonly data; minimize chip reads */
|
|
ehci->hcs_params = readl (&ehci->caps->hcs_params);
|
|
|
|
if (hcd->self.controller->bus == &pci_bus_type) {
|
|
struct pci_dev *pdev = to_pci_dev(hcd->self.controller);
|
|
|
|
switch (pdev->vendor) {
|
|
case PCI_VENDOR_ID_TDI:
|
|
if (pdev->device == PCI_DEVICE_ID_TDI_EHCI) {
|
|
ehci->is_tdi_rh_tt = 1;
|
|
tdi_reset (ehci);
|
|
}
|
|
break;
|
|
case PCI_VENDOR_ID_AMD:
|
|
/* AMD8111 EHCI doesn't work, according to AMD errata */
|
|
if (pdev->device == 0x7463) {
|
|
ehci_info (ehci, "ignoring AMD8111 (errata)\n");
|
|
return -EIO;
|
|
}
|
|
break;
|
|
case PCI_VENDOR_ID_NVIDIA:
|
|
/* NVidia reports that certain chips don't handle
|
|
* QH, ITD, or SITD addresses above 2GB. (But TD,
|
|
* data buffer, and periodic schedule are normal.)
|
|
*/
|
|
switch (pdev->device) {
|
|
case 0x003c: /* MCP04 */
|
|
case 0x005b: /* CK804 */
|
|
case 0x00d8: /* CK8 */
|
|
case 0x00e8: /* CK8S */
|
|
if (pci_set_consistent_dma_mask(pdev,
|
|
DMA_31BIT_MASK) < 0)
|
|
ehci_warn (ehci, "can't enable NVidia "
|
|
"workaround for >2GB RAM\n");
|
|
break;
|
|
}
|
|
break;
|
|
}
|
|
|
|
/* optional debug port, normally in the first BAR */
|
|
temp = pci_find_capability (pdev, 0x0a);
|
|
if (temp) {
|
|
pci_read_config_dword(pdev, temp, &temp);
|
|
temp >>= 16;
|
|
if ((temp & (3 << 13)) == (1 << 13)) {
|
|
temp &= 0x1fff;
|
|
ehci->debug = hcd->regs + temp;
|
|
temp = readl (&ehci->debug->control);
|
|
ehci_info (ehci, "debug port %d%s\n",
|
|
HCS_DEBUG_PORT(ehci->hcs_params),
|
|
(temp & DBGP_ENABLED)
|
|
? " IN USE"
|
|
: "");
|
|
if (!(temp & DBGP_ENABLED))
|
|
ehci->debug = NULL;
|
|
}
|
|
}
|
|
|
|
temp = HCC_EXT_CAPS (readl (&ehci->caps->hcc_params));
|
|
} else
|
|
temp = 0;
|
|
|
|
/* EHCI 0.96 and later may have "extended capabilities" */
|
|
while (temp && count--) {
|
|
u32 cap;
|
|
|
|
pci_read_config_dword (to_pci_dev(hcd->self.controller),
|
|
temp, &cap);
|
|
ehci_dbg (ehci, "capability %04x at %02x\n", cap, temp);
|
|
switch (cap & 0xff) {
|
|
case 1: /* BIOS/SMM/... handoff */
|
|
if (bios_handoff (ehci, temp, cap) != 0)
|
|
return -EOPNOTSUPP;
|
|
break;
|
|
case 0: /* illegal reserved capability */
|
|
ehci_warn (ehci, "illegal capability!\n");
|
|
cap = 0;
|
|
/* FALLTHROUGH */
|
|
default: /* unknown */
|
|
break;
|
|
}
|
|
temp = (cap >> 8) & 0xff;
|
|
}
|
|
if (!count) {
|
|
ehci_err (ehci, "bogus capabilities ... PCI problems!\n");
|
|
return -EIO;
|
|
}
|
|
if (ehci_is_TDI(ehci))
|
|
ehci_reset (ehci);
|
|
|
|
ehci_port_power (ehci, 0);
|
|
|
|
/* at least the Genesys GL880S needs fixup here */
|
|
temp = HCS_N_CC(ehci->hcs_params) * HCS_N_PCC(ehci->hcs_params);
|
|
temp &= 0x0f;
|
|
if (temp && HCS_N_PORTS(ehci->hcs_params) > temp) {
|
|
ehci_dbg (ehci, "bogus port configuration: "
|
|
"cc=%d x pcc=%d < ports=%d\n",
|
|
HCS_N_CC(ehci->hcs_params),
|
|
HCS_N_PCC(ehci->hcs_params),
|
|
HCS_N_PORTS(ehci->hcs_params));
|
|
|
|
if (hcd->self.controller->bus == &pci_bus_type) {
|
|
struct pci_dev *pdev;
|
|
|
|
pdev = to_pci_dev(hcd->self.controller);
|
|
switch (pdev->vendor) {
|
|
case 0x17a0: /* GENESYS */
|
|
/* GL880S: should be PORTS=2 */
|
|
temp |= (ehci->hcs_params & ~0xf);
|
|
ehci->hcs_params = temp;
|
|
break;
|
|
case PCI_VENDOR_ID_NVIDIA:
|
|
/* NF4: should be PCC=10 */
|
|
break;
|
|
}
|
|
}
|
|
}
|
|
|
|
/* force HC to halt state */
|
|
return ehci_halt (ehci);
|
|
}
|
|
|
|
static int ehci_pci_start (struct usb_hcd *hcd)
|
|
{
|
|
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
|
|
int result = 0;
|
|
|
|
if (hcd->self.controller->bus == &pci_bus_type) {
|
|
struct pci_dev *pdev;
|
|
u16 port_wake;
|
|
|
|
pdev = to_pci_dev(hcd->self.controller);
|
|
|
|
/* Serial Bus Release Number is at PCI 0x60 offset */
|
|
pci_read_config_byte(pdev, 0x60, &ehci->sbrn);
|
|
|
|
/* port wake capability, reported by boot firmware */
|
|
pci_read_config_word(pdev, 0x62, &port_wake);
|
|
hcd->can_wakeup = (port_wake & 1) != 0;
|
|
|
|
/* help hc dma work well with cachelines */
|
|
result = pci_set_mwi(pdev);
|
|
if (result)
|
|
ehci_dbg(ehci, "unable to enable MWI - not fatal.\n");
|
|
}
|
|
|
|
return ehci_run (hcd);
|
|
}
|
|
|
|
/* always called by thread; normally rmmod */
|
|
|
|
static void ehci_pci_stop (struct usb_hcd *hcd)
|
|
{
|
|
ehci_stop (hcd);
|
|
}
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
#ifdef CONFIG_PM
|
|
|
|
/* suspend/resume, section 4.3 */
|
|
|
|
/* These routines rely on the bus (pci, platform, etc)
|
|
* to handle powerdown and wakeup, and currently also on
|
|
* transceivers that don't need any software attention to set up
|
|
* the right sort of wakeup.
|
|
*/
|
|
|
|
static int ehci_pci_suspend (struct usb_hcd *hcd, pm_message_t message)
|
|
{
|
|
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
|
|
|
|
if (time_before (jiffies, ehci->next_statechange))
|
|
msleep (100);
|
|
|
|
#ifdef CONFIG_USB_SUSPEND
|
|
(void) usb_suspend_device (hcd->self.root_hub);
|
|
#else
|
|
usb_lock_device (hcd->self.root_hub);
|
|
(void) ehci_hub_suspend (hcd);
|
|
usb_unlock_device (hcd->self.root_hub);
|
|
#endif
|
|
|
|
// save (PCI) FLADJ in case of Vaux power loss
|
|
// ... we'd only use it to handle clock skew
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int ehci_pci_resume (struct usb_hcd *hcd)
|
|
{
|
|
struct ehci_hcd *ehci = hcd_to_ehci (hcd);
|
|
unsigned port;
|
|
struct usb_device *root = hcd->self.root_hub;
|
|
int retval = -EINVAL;
|
|
|
|
// maybe restore (PCI) FLADJ
|
|
|
|
if (time_before (jiffies, ehci->next_statechange))
|
|
msleep (100);
|
|
|
|
/* If any port is suspended (or owned by the companion),
|
|
* we know we can/must resume the HC (and mustn't reset it).
|
|
*/
|
|
for (port = HCS_N_PORTS (ehci->hcs_params); port > 0; ) {
|
|
u32 status;
|
|
port--;
|
|
status = readl (&ehci->regs->port_status [port]);
|
|
if (!(status & PORT_POWER))
|
|
continue;
|
|
if (status & (PORT_SUSPEND | PORT_OWNER)) {
|
|
down (&hcd->self.root_hub->serialize);
|
|
retval = ehci_hub_resume (hcd);
|
|
up (&hcd->self.root_hub->serialize);
|
|
break;
|
|
}
|
|
if (!root->children [port])
|
|
continue;
|
|
dbg_port (ehci, __FUNCTION__, port + 1, status);
|
|
usb_set_device_state (root->children[port],
|
|
USB_STATE_NOTATTACHED);
|
|
}
|
|
|
|
/* Else reset, to cope with power loss or flush-to-storage
|
|
* style "resume" having activated BIOS during reboot.
|
|
*/
|
|
if (port == 0) {
|
|
(void) ehci_halt (ehci);
|
|
(void) ehci_reset (ehci);
|
|
(void) ehci_pci_reset (hcd);
|
|
|
|
/* emptying the schedule aborts any urbs */
|
|
spin_lock_irq (&ehci->lock);
|
|
if (ehci->reclaim)
|
|
ehci->reclaim_ready = 1;
|
|
ehci_work (ehci, NULL);
|
|
spin_unlock_irq (&ehci->lock);
|
|
|
|
/* restart; khubd will disconnect devices */
|
|
retval = ehci_run (hcd);
|
|
|
|
/* here we "know" root ports should always stay powered;
|
|
* but some controllers may lose all power.
|
|
*/
|
|
ehci_port_power (ehci, 1);
|
|
}
|
|
|
|
return retval;
|
|
}
|
|
#endif
|
|
|
|
static const struct hc_driver ehci_pci_hc_driver = {
|
|
.description = hcd_name,
|
|
.product_desc = "EHCI Host Controller",
|
|
.hcd_priv_size = sizeof(struct ehci_hcd),
|
|
|
|
/*
|
|
* generic hardware linkage
|
|
*/
|
|
.irq = ehci_irq,
|
|
.flags = HCD_MEMORY | HCD_USB2,
|
|
|
|
/*
|
|
* basic lifecycle operations
|
|
*/
|
|
.reset = ehci_pci_reset,
|
|
.start = ehci_pci_start,
|
|
#ifdef CONFIG_PM
|
|
.suspend = ehci_pci_suspend,
|
|
.resume = ehci_pci_resume,
|
|
#endif
|
|
.stop = ehci_pci_stop,
|
|
|
|
/*
|
|
* managing i/o requests and associated device resources
|
|
*/
|
|
.urb_enqueue = ehci_urb_enqueue,
|
|
.urb_dequeue = ehci_urb_dequeue,
|
|
.endpoint_disable = ehci_endpoint_disable,
|
|
|
|
/*
|
|
* scheduling support
|
|
*/
|
|
.get_frame_number = ehci_get_frame,
|
|
|
|
/*
|
|
* root hub support
|
|
*/
|
|
.hub_status_data = ehci_hub_status_data,
|
|
.hub_control = ehci_hub_control,
|
|
.bus_suspend = ehci_bus_suspend,
|
|
.bus_resume = ehci_bus_resume,
|
|
};
|
|
|
|
/*-------------------------------------------------------------------------*/
|
|
|
|
/* PCI driver selection metadata; PCI hotplugging uses this */
|
|
static const struct pci_device_id pci_ids [] = { {
|
|
/* handle any USB 2.0 EHCI controller */
|
|
PCI_DEVICE_CLASS(((PCI_CLASS_SERIAL_USB << 8) | 0x20), ~0),
|
|
.driver_data = (unsigned long) &ehci_pci_hc_driver,
|
|
},
|
|
{ /* end: all zeroes */ }
|
|
};
|
|
MODULE_DEVICE_TABLE (pci, pci_ids);
|
|
|
|
/* pci driver glue; this is a "new style" PCI driver module */
|
|
static struct pci_driver ehci_pci_driver = {
|
|
.name = (char *) hcd_name,
|
|
.id_table = pci_ids,
|
|
|
|
.probe = usb_hcd_pci_probe,
|
|
.remove = usb_hcd_pci_remove,
|
|
|
|
#ifdef CONFIG_PM
|
|
.suspend = usb_hcd_pci_suspend,
|
|
.resume = usb_hcd_pci_resume,
|
|
#endif
|
|
};
|
|
|
|
static int __init ehci_hcd_pci_init (void)
|
|
{
|
|
if (usb_disabled())
|
|
return -ENODEV;
|
|
|
|
pr_debug ("%s: block sizes: qh %Zd qtd %Zd itd %Zd sitd %Zd\n",
|
|
hcd_name,
|
|
sizeof (struct ehci_qh), sizeof (struct ehci_qtd),
|
|
sizeof (struct ehci_itd), sizeof (struct ehci_sitd));
|
|
|
|
return pci_register_driver (&ehci_pci_driver);
|
|
}
|
|
module_init (ehci_hcd_pci_init);
|
|
|
|
static void __exit ehci_hcd_pci_cleanup (void)
|
|
{
|
|
pci_unregister_driver (&ehci_pci_driver);
|
|
}
|
|
module_exit (ehci_hcd_pci_cleanup);
|