kevin/linux
1
Fork 0
Code
083d06edfd
linux/arch/arm/mach-ixp2000/enp2611.c
Lennert Buytenhek f8e5b28413 [ARM] 3302/1: make pci=firmware the default for ixp2000 
Patch from Lennert Buytenhek

Most ixp2000 boards don't actually work if pci=firmware isn't used, so
the defconfig isn't really the right place to specify this.  Instead of
specifying it in the defconfigs, make the relevant board code take care
of setting pci=firmware.

Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-02-08 21:09:04 +00:00

268 lines
6.9 KiB
C
Raw Blame History

/*
* arch/arm/mach-ixp2000/enp2611.c
*
* Radisys ENP-2611 support.
*
* Created 2004 by Lennert Buytenhek from the ixdp2x01 code. The
* original version carries the following notices:
*
* Original Author: Andrzej Mialkowski <andrzej.mialkowski@intel.com>
* Maintainer: Deepak Saxena <dsaxena@plexity.net>
*
* Copyright (C) 2002-2003 Intel Corp.
* Copyright (C) 2003-2004 MontaVista Software, Inc.
*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License as published by the
* Free Software Foundation; either version 2 of the License, or (at your
* option) any later version.
*/
#include <linux/config.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/mm.h>
#include <linux/sched.h>
#include <linux/interrupt.h>
#include <linux/bitops.h>
#include <linux/pci.h>
#include <linux/ioport.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/serial.h>
#include <linux/tty.h>
#include <linux/serial_core.h>
#include <linux/platform_device.h>
#include <asm/io.h>
#include <asm/irq.h>
#include <asm/pgtable.h>
#include <asm/page.h>
#include <asm/system.h>
#include <asm/hardware.h>
#include <asm/mach-types.h>
#include <asm/mach/pci.h>
#include <asm/mach/map.h>
#include <asm/mach/irq.h>
#include <asm/mach/time.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
/*************************************************************************
* ENP-2611 timer tick configuration
*************************************************************************/
static void __init enp2611_timer_init(void)
{
ixp2000_init_time(50 * 1000 * 1000);
}
static struct sys_timer enp2611_timer = {
.init = enp2611_timer_init,
.offset = ixp2000_gettimeoffset,
};
/*************************************************************************
* ENP-2611 I/O
*************************************************************************/
static struct map_desc enp2611_io_desc[] __initdata = {
{
.virtual = ENP2611_CALEB_VIRT_BASE,
.pfn = __phys_to_pfn(ENP2611_CALEB_PHYS_BASE),
.length = ENP2611_CALEB_SIZE,
.type = MT_IXP2000_DEVICE,
}, {
.virtual = ENP2611_PM3386_0_VIRT_BASE,
.pfn = __phys_to_pfn(ENP2611_PM3386_0_PHYS_BASE),
.length = ENP2611_PM3386_0_SIZE,
.type = MT_IXP2000_DEVICE,
}, {
.virtual = ENP2611_PM3386_1_VIRT_BASE,
.pfn = __phys_to_pfn(ENP2611_PM3386_1_PHYS_BASE),
.length = ENP2611_PM3386_1_SIZE,
.type = MT_IXP2000_DEVICE,
}
};
void __init enp2611_map_io(void)
{
ixp2000_map_io();
iotable_init(enp2611_io_desc, ARRAY_SIZE(enp2611_io_desc));
}
/*************************************************************************
* ENP-2611 PCI
*************************************************************************/
static int enp2611_pci_setup(int nr, struct pci_sys_data *sys)
{
sys->mem_offset = 0xe0000000;
ixp2000_pci_setup(nr, sys);
return 1;
}
static void __init enp2611_pci_preinit(void)
{
ixp2000_reg_write(IXP2000_PCI_ADDR_EXT, 0x00100000);
ixp2000_pci_preinit();
pcibios_setup("firmware");
}
static inline int enp2611_pci_valid_device(struct pci_bus *bus,
unsigned int devfn)
{
/* The 82559 ethernet controller appears at both PCI:1:0:0 and
* PCI:1:2:0, so let's pretend the second one isn't there.
*/
if (bus->number == 0x01 && devfn == 0x10)
return 0;
return 1;
}
static int enp2611_pci_read_config(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 *value)
{
if (enp2611_pci_valid_device(bus, devfn))
return ixp2000_pci_read_config(bus, devfn, where, size, value);
return PCIBIOS_DEVICE_NOT_FOUND;
}
static int enp2611_pci_write_config(struct pci_bus *bus, unsigned int devfn,
int where, int size, u32 value)
{
if (enp2611_pci_valid_device(bus, devfn))
return ixp2000_pci_write_config(bus, devfn, where, size, value);
return PCIBIOS_DEVICE_NOT_FOUND;
}
static struct pci_ops enp2611_pci_ops = {
.read = enp2611_pci_read_config,
.write = enp2611_pci_write_config
};
static struct pci_bus * __init enp2611_pci_scan_bus(int nr,
struct pci_sys_data *sys)
{
return pci_scan_bus(sys->busnr, &enp2611_pci_ops, sys);
}
static int __init enp2611_pci_map_irq(struct pci_dev *dev, u8 slot, u8 pin)
{
int irq;
if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 0) {
/* IXP2400. */
irq = IRQ_IXP2000_PCIA;
} else if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 1) {
/* 21555 non-transparent bridge. */
irq = IRQ_IXP2000_PCIB;
} else if (dev->bus->number == 0 && PCI_SLOT(dev->devfn) == 4) {
/* PCI2050B transparent bridge. */
irq = -1;
} else if (dev->bus->number == 1 && PCI_SLOT(dev->devfn) == 0) {
/* 82559 ethernet. */
irq = IRQ_IXP2000_PCIA;
} else if (dev->bus->number == 1 && PCI_SLOT(dev->devfn) == 1) {
/* SPI-3 option board. */
irq = IRQ_IXP2000_PCIB;
} else {
printk(KERN_ERR "enp2611_pci_map_irq() called for unknown "
"device PCI:%d:%d:%d\n", dev->bus->number,
PCI_SLOT(dev->devfn), PCI_FUNC(dev->devfn));
irq = -1;
}
return irq;
}
struct hw_pci enp2611_pci __initdata = {
.nr_controllers = 1,
.setup = enp2611_pci_setup,
.preinit = enp2611_pci_preinit,
.scan = enp2611_pci_scan_bus,
.map_irq = enp2611_pci_map_irq,
};
int __init enp2611_pci_init(void)
{
if (machine_is_enp2611())
pci_common_init(&enp2611_pci);
return 0;
}
subsys_initcall(enp2611_pci_init);
/*************************************************************************
* ENP-2611 Machine Intialization
*************************************************************************/
static struct flash_platform_data enp2611_flash_platform_data = {
.map_name = "cfi_probe",
.width = 1,
};
static struct ixp2000_flash_data enp2611_flash_data = {
.platform_data = &enp2611_flash_platform_data,
.nr_banks = 1
};
static struct resource enp2611_flash_resource = {
.start = 0xc4000000,
.end = 0xc4000000 + 0x00ffffff,
.flags = IORESOURCE_MEM,
};
static struct platform_device enp2611_flash = {
.name = "IXP2000-Flash",
.id = 0,
.dev = {
.platform_data = &enp2611_flash_data,
},
.num_resources = 1,
.resource = &enp2611_flash_resource,
};
static struct ixp2000_i2c_pins enp2611_i2c_gpio_pins = {
.sda_pin = ENP2611_GPIO_SDA,
.scl_pin = ENP2611_GPIO_SCL,
};
static struct platform_device enp2611_i2c_controller = {
.name = "IXP2000-I2C",
.id = 0,
.dev = {
.platform_data = &enp2611_i2c_gpio_pins
},
.num_resources = 0
};
static struct platform_device *enp2611_devices[] __initdata = {
&enp2611_flash,
&enp2611_i2c_controller
};
static void __init enp2611_init_machine(void)
{
platform_add_devices(enp2611_devices, ARRAY_SIZE(enp2611_devices));
ixp2000_uart_init();
}
MACHINE_START(ENP2611, "Radisys ENP-2611 PCI network processor board")
/* Maintainer: Lennert Buytenhek <buytenh@wantstofly.org> */
.phys_io = IXP2000_UART_PHYS_BASE,
.io_pg_offst = ((IXP2000_UART_VIRT_BASE) >> 18) & 0xfffc,
.boot_params = 0x00000100,
.map_io = enp2611_map_io,
.init_irq = ixp2000_init_irq,
.timer = &enp2611_timer,
.init_machine = enp2611_init_machine,
MACHINE_END
View Git Blame Copy Permalink