13fc6c1759
According to the code logic, when the kernel is loaded at address 0, no
copying operation should be performed, but it is currently being done.
This patch fixes the issue where the kernel code was incorrectly
duplicated to address 0 when booting from address 0.
Fixes: b270bebd34
("powerpc/64s: Run at the kernel virtual address earlier in boot")
Cc: stable@vger.kernel.org # v6.4+
Signed-off-by: Jinglin Wen <jinglin.wen@shingroup.cn>
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://msgid.link/20240620024150.14857-1-jinglin.wen@shingroup.cn
1046 lines
26 KiB
ArmAsm
1046 lines
26 KiB
ArmAsm
/* SPDX-License-Identifier: GPL-2.0-or-later */
|
|
/*
|
|
* PowerPC version
|
|
* Copyright (C) 1995-1996 Gary Thomas (gdt@linuxppc.org)
|
|
*
|
|
* Rewritten by Cort Dougan (cort@cs.nmt.edu) for PReP
|
|
* Copyright (C) 1996 Cort Dougan <cort@cs.nmt.edu>
|
|
* Adapted for Power Macintosh by Paul Mackerras.
|
|
* Low-level exception handlers and MMU support
|
|
* rewritten by Paul Mackerras.
|
|
* Copyright (C) 1996 Paul Mackerras.
|
|
*
|
|
* Adapted for 64bit PowerPC by Dave Engebretsen, Peter Bergner, and
|
|
* Mike Corrigan {engebret|bergner|mikejc}@us.ibm.com
|
|
*
|
|
* This file contains the entry point for the 64-bit kernel along
|
|
* with some early initialization code common to all 64-bit powerpc
|
|
* variants.
|
|
*/
|
|
|
|
#include <linux/linkage.h>
|
|
#include <linux/threads.h>
|
|
#include <linux/init.h>
|
|
#include <asm/reg.h>
|
|
#include <asm/page.h>
|
|
#include <asm/mmu.h>
|
|
#include <asm/ppc_asm.h>
|
|
#include <asm/head-64.h>
|
|
#include <asm/asm-offsets.h>
|
|
#include <asm/bug.h>
|
|
#include <asm/cputable.h>
|
|
#include <asm/setup.h>
|
|
#include <asm/hvcall.h>
|
|
#include <asm/thread_info.h>
|
|
#include <asm/firmware.h>
|
|
#include <asm/page_64.h>
|
|
#include <asm/irqflags.h>
|
|
#include <asm/kvm_book3s_asm.h>
|
|
#include <asm/ptrace.h>
|
|
#include <asm/hw_irq.h>
|
|
#include <asm/cputhreads.h>
|
|
#include <asm/ppc-opcode.h>
|
|
#include <asm/feature-fixups.h>
|
|
#ifdef CONFIG_PPC_BOOK3S
|
|
#include <asm/exception-64s.h>
|
|
#else
|
|
#include <asm/exception-64e.h>
|
|
#endif
|
|
|
|
/* The physical memory is laid out such that the secondary processor
|
|
* spin code sits at 0x0000...0x00ff. On server, the vectors follow
|
|
* using the layout described in exceptions-64s.S
|
|
*/
|
|
|
|
/*
|
|
* Entering into this code we make the following assumptions:
|
|
*
|
|
* For pSeries or server processors:
|
|
* 1. The MMU is off & open firmware is running in real mode.
|
|
* 2. The primary CPU enters at __start.
|
|
* 3. If the RTAS supports "query-cpu-stopped-state", then secondary
|
|
* CPUs will enter as directed by "start-cpu" RTAS call, which is
|
|
* generic_secondary_smp_init, with PIR in r3.
|
|
* 4. Else the secondary CPUs will enter at secondary_hold (0x60) as
|
|
* directed by the "start-cpu" RTS call, with PIR in r3.
|
|
* -or- For OPAL entry:
|
|
* 1. The MMU is off, processor in HV mode.
|
|
* 2. The primary CPU enters at 0 with device-tree in r3, OPAL base
|
|
* in r8, and entry in r9 for debugging purposes.
|
|
* 3. Secondary CPUs enter as directed by OPAL_START_CPU call, which
|
|
* is at generic_secondary_smp_init, with PIR in r3.
|
|
*
|
|
* For Book3E processors:
|
|
* 1. The MMU is on running in AS0 in a state defined in ePAPR
|
|
* 2. The kernel is entered at __start
|
|
*/
|
|
|
|
/*
|
|
* boot_from_prom and prom_init run at the physical address. Everything
|
|
* after prom and kexec entry run at the virtual address (PAGE_OFFSET).
|
|
* Secondaries run at the virtual address from generic_secondary_common_init
|
|
* onward.
|
|
*/
|
|
|
|
OPEN_FIXED_SECTION(first_256B, 0x0, 0x100)
|
|
USE_FIXED_SECTION(first_256B)
|
|
/*
|
|
* Offsets are relative from the start of fixed section, and
|
|
* first_256B starts at 0. Offsets are a bit easier to use here
|
|
* than the fixed section entry macros.
|
|
*/
|
|
. = 0x0
|
|
_GLOBAL(__start)
|
|
/* NOP this out unconditionally */
|
|
BEGIN_FTR_SECTION
|
|
FIXUP_ENDIAN
|
|
b __start_initialization_multiplatform
|
|
END_FTR_SECTION(0, 1)
|
|
|
|
/* Catch branch to 0 in real mode */
|
|
trap
|
|
|
|
/* Secondary processors spin on this value until it becomes non-zero.
|
|
* When non-zero, it contains the real address of the function the cpu
|
|
* should jump to.
|
|
*/
|
|
.balign 8
|
|
.globl __secondary_hold_spinloop
|
|
__secondary_hold_spinloop:
|
|
.8byte 0x0
|
|
|
|
/* Secondary processors write this value with their cpu # */
|
|
/* after they enter the spin loop immediately below. */
|
|
.globl __secondary_hold_acknowledge
|
|
__secondary_hold_acknowledge:
|
|
.8byte 0x0
|
|
|
|
#ifdef CONFIG_RELOCATABLE
|
|
/* This flag is set to 1 by a loader if the kernel should run
|
|
* at the loaded address instead of the linked address. This
|
|
* is used by kexec-tools to keep the kdump kernel in the
|
|
* crash_kernel region. The loader is responsible for
|
|
* observing the alignment requirement.
|
|
*/
|
|
|
|
#ifdef CONFIG_RELOCATABLE_TEST
|
|
#define RUN_AT_LOAD_DEFAULT 1 /* Test relocation, do not copy to 0 */
|
|
#else
|
|
#define RUN_AT_LOAD_DEFAULT 0x72756e30 /* "run0" -- relocate to 0 by default */
|
|
#endif
|
|
|
|
/* Do not move this variable as kexec-tools knows about it. */
|
|
. = 0x5c
|
|
.globl __run_at_load
|
|
__run_at_load:
|
|
DEFINE_FIXED_SYMBOL(__run_at_load, first_256B)
|
|
.long RUN_AT_LOAD_DEFAULT
|
|
#endif
|
|
|
|
. = 0x60
|
|
/*
|
|
* The following code is used to hold secondary processors
|
|
* in a spin loop after they have entered the kernel, but
|
|
* before the bulk of the kernel has been relocated. This code
|
|
* is relocated to physical address 0x60 before prom_init is run.
|
|
* All of it must fit below the first exception vector at 0x100.
|
|
* Use .globl here not _GLOBAL because we want __secondary_hold
|
|
* to be the actual text address, not a descriptor.
|
|
*/
|
|
.globl __secondary_hold
|
|
__secondary_hold:
|
|
FIXUP_ENDIAN
|
|
#ifndef CONFIG_PPC_BOOK3E_64
|
|
mfmsr r24
|
|
ori r24,r24,MSR_RI
|
|
mtmsrd r24 /* RI on */
|
|
#endif
|
|
/* Grab our physical cpu number */
|
|
mr r24,r3
|
|
/* stash r4 for book3e */
|
|
mr r25,r4
|
|
|
|
/* Tell the master cpu we're here */
|
|
/* Relocation is off & we are located at an address less */
|
|
/* than 0x100, so only need to grab low order offset. */
|
|
std r24,(ABS_ADDR(__secondary_hold_acknowledge, first_256B))(0)
|
|
sync
|
|
|
|
/* All secondary cpus wait here until told to start. */
|
|
100: ld r12,(ABS_ADDR(__secondary_hold_spinloop, first_256B))(0)
|
|
cmpdi 0,r12,0
|
|
beq 100b
|
|
|
|
#if defined(CONFIG_SMP) || defined(CONFIG_KEXEC_CORE)
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
tovirt(r12,r12)
|
|
#endif
|
|
mtctr r12
|
|
mr r3,r24
|
|
/*
|
|
* it may be the case that other platforms have r4 right to
|
|
* begin with, this gives us some safety in case it is not
|
|
*/
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
mr r4,r25
|
|
#else
|
|
li r4,0
|
|
#endif
|
|
/* Make sure that patched code is visible */
|
|
isync
|
|
bctr
|
|
#else
|
|
0: trap
|
|
EMIT_BUG_ENTRY 0b, __FILE__, __LINE__, 0
|
|
#endif
|
|
CLOSE_FIXED_SECTION(first_256B)
|
|
|
|
/*
|
|
* On server, we include the exception vectors code here as it
|
|
* relies on absolute addressing which is only possible within
|
|
* this compilation unit
|
|
*/
|
|
#ifdef CONFIG_PPC_BOOK3S
|
|
#include "exceptions-64s.S"
|
|
#else
|
|
OPEN_TEXT_SECTION(0x100)
|
|
#endif
|
|
|
|
USE_TEXT_SECTION()
|
|
|
|
#include "interrupt_64.S"
|
|
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
/*
|
|
* The booting_thread_hwid holds the thread id we want to boot in cpu
|
|
* hotplug case. It is set by cpu hotplug code, and is invalid by default.
|
|
* The thread id is the same as the initial value of SPRN_PIR[THREAD_ID]
|
|
* bit field.
|
|
*/
|
|
.globl booting_thread_hwid
|
|
booting_thread_hwid:
|
|
.long INVALID_THREAD_HWID
|
|
.align 3
|
|
/*
|
|
* start a thread in the same core
|
|
* input parameters:
|
|
* r3 = the thread physical id
|
|
* r4 = the entry point where thread starts
|
|
*/
|
|
_GLOBAL(book3e_start_thread)
|
|
LOAD_REG_IMMEDIATE(r5, MSR_KERNEL)
|
|
cmpwi r3, 0
|
|
beq 10f
|
|
cmpwi r3, 1
|
|
beq 11f
|
|
/* If the thread id is invalid, just exit. */
|
|
b 13f
|
|
10:
|
|
MTTMR(TMRN_IMSR0, 5)
|
|
MTTMR(TMRN_INIA0, 4)
|
|
b 12f
|
|
11:
|
|
MTTMR(TMRN_IMSR1, 5)
|
|
MTTMR(TMRN_INIA1, 4)
|
|
12:
|
|
isync
|
|
li r6, 1
|
|
sld r6, r6, r3
|
|
mtspr SPRN_TENS, r6
|
|
13:
|
|
blr
|
|
|
|
/*
|
|
* stop a thread in the same core
|
|
* input parameter:
|
|
* r3 = the thread physical id
|
|
*/
|
|
_GLOBAL(book3e_stop_thread)
|
|
cmpwi r3, 0
|
|
beq 10f
|
|
cmpwi r3, 1
|
|
beq 10f
|
|
/* If the thread id is invalid, just exit. */
|
|
b 13f
|
|
10:
|
|
li r4, 1
|
|
sld r4, r4, r3
|
|
mtspr SPRN_TENC, r4
|
|
13:
|
|
blr
|
|
|
|
_GLOBAL(fsl_secondary_thread_init)
|
|
mfspr r4,SPRN_BUCSR
|
|
|
|
/* Enable branch prediction */
|
|
lis r3,BUCSR_INIT@h
|
|
ori r3,r3,BUCSR_INIT@l
|
|
mtspr SPRN_BUCSR,r3
|
|
isync
|
|
|
|
/*
|
|
* Fix PIR to match the linear numbering in the device tree.
|
|
*
|
|
* On e6500, the reset value of PIR uses the low three bits for
|
|
* the thread within a core, and the upper bits for the core
|
|
* number. There are two threads per core, so shift everything
|
|
* but the low bit right by two bits so that the cpu numbering is
|
|
* continuous.
|
|
*
|
|
* If the old value of BUCSR is non-zero, this thread has run
|
|
* before. Thus, we assume we are coming from kexec or a similar
|
|
* scenario, and PIR is already set to the correct value. This
|
|
* is a bit of a hack, but there are limited opportunities for
|
|
* getting information into the thread and the alternatives
|
|
* seemed like they'd be overkill. We can't tell just by looking
|
|
* at the old PIR value which state it's in, since the same value
|
|
* could be valid for one thread out of reset and for a different
|
|
* thread in Linux.
|
|
*/
|
|
|
|
mfspr r3, SPRN_PIR
|
|
cmpwi r4,0
|
|
bne 1f
|
|
rlwimi r3, r3, 30, 2, 30
|
|
mtspr SPRN_PIR, r3
|
|
1:
|
|
mr r24,r3
|
|
|
|
/* turn on 64-bit mode */
|
|
bl enable_64b_mode
|
|
|
|
/* Book3E initialization */
|
|
mr r3,r24
|
|
bl book3e_secondary_thread_init
|
|
bl relative_toc
|
|
|
|
b generic_secondary_common_init
|
|
|
|
#endif /* CONFIG_PPC_BOOK3E_64 */
|
|
|
|
/*
|
|
* On pSeries and most other platforms, secondary processors spin
|
|
* in the following code.
|
|
* At entry, r3 = this processor's number (physical cpu id)
|
|
*
|
|
* On Book3E, r4 = 1 to indicate that the initial TLB entry for
|
|
* this core already exists (setup via some other mechanism such
|
|
* as SCOM before entry).
|
|
*/
|
|
_GLOBAL(generic_secondary_smp_init)
|
|
FIXUP_ENDIAN
|
|
|
|
li r13,0
|
|
|
|
/* Poison TOC */
|
|
li r2,-1
|
|
|
|
mr r24,r3
|
|
mr r25,r4
|
|
|
|
/* turn on 64-bit mode */
|
|
bl enable_64b_mode
|
|
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
/* Book3E initialization */
|
|
mr r3,r24
|
|
mr r4,r25
|
|
bl book3e_secondary_core_init
|
|
/* Now NIA and r2 are relocated to PAGE_OFFSET if not already */
|
|
/*
|
|
* After common core init has finished, check if the current thread is the
|
|
* one we wanted to boot. If not, start the specified thread and stop the
|
|
* current thread.
|
|
*/
|
|
LOAD_REG_ADDR(r4, booting_thread_hwid)
|
|
lwz r3, 0(r4)
|
|
li r5, INVALID_THREAD_HWID
|
|
cmpw r3, r5
|
|
beq 20f
|
|
|
|
/*
|
|
* The value of booting_thread_hwid has been stored in r3,
|
|
* so make it invalid.
|
|
*/
|
|
stw r5, 0(r4)
|
|
|
|
/*
|
|
* Get the current thread id and check if it is the one we wanted.
|
|
* If not, start the one specified in booting_thread_hwid and stop
|
|
* the current thread.
|
|
*/
|
|
mfspr r8, SPRN_TIR
|
|
cmpw r3, r8
|
|
beq 20f
|
|
|
|
/* start the specified thread */
|
|
LOAD_REG_ADDR(r5, DOTSYM(fsl_secondary_thread_init))
|
|
bl book3e_start_thread
|
|
|
|
/* stop the current thread */
|
|
mr r3, r8
|
|
bl book3e_stop_thread
|
|
10:
|
|
b 10b
|
|
20:
|
|
#else
|
|
/* Now the MMU is off, can branch to our PAGE_OFFSET address */
|
|
bcl 20,31,$+4
|
|
1: mflr r11
|
|
addi r11,r11,(2f - 1b)
|
|
tovirt(r11, r11)
|
|
mtctr r11
|
|
bctr
|
|
2:
|
|
bl relative_toc
|
|
#endif
|
|
|
|
generic_secondary_common_init:
|
|
/* Set up a paca value for this processor. Since we have the
|
|
* physical cpu id in r24, we need to search the pacas to find
|
|
* which logical id maps to our physical one.
|
|
*/
|
|
#ifndef CONFIG_SMP
|
|
b kexec_wait /* wait for next kernel if !SMP */
|
|
#else
|
|
LOAD_REG_ADDR(r8, paca_ptrs) /* Load paca_ptrs pointe */
|
|
ld r8,0(r8) /* Get base vaddr of array */
|
|
#if (NR_CPUS == 1) || defined(CONFIG_FORCE_NR_CPUS)
|
|
LOAD_REG_IMMEDIATE(r7, NR_CPUS)
|
|
#else
|
|
LOAD_REG_ADDR(r7, nr_cpu_ids) /* Load nr_cpu_ids address */
|
|
lwz r7,0(r7) /* also the max paca allocated */
|
|
#endif
|
|
li r5,0 /* logical cpu id */
|
|
1:
|
|
sldi r9,r5,3 /* get paca_ptrs[] index from cpu id */
|
|
ldx r13,r9,r8 /* r13 = paca_ptrs[cpu id] */
|
|
lhz r6,PACAHWCPUID(r13) /* Load HW procid from paca */
|
|
cmpw r6,r24 /* Compare to our id */
|
|
beq 2f
|
|
addi r5,r5,1
|
|
cmpw r5,r7 /* Check if more pacas exist */
|
|
blt 1b
|
|
|
|
mr r3,r24 /* not found, copy phys to r3 */
|
|
b kexec_wait /* next kernel might do better */
|
|
|
|
2: SET_PACA(r13)
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
addi r12,r13,PACA_EXTLB /* and TLB exc frame in another */
|
|
mtspr SPRN_SPRG_TLB_EXFRAME,r12
|
|
#endif
|
|
|
|
/* From now on, r24 is expected to be logical cpuid */
|
|
mr r24,r5
|
|
|
|
/* Create a temp kernel stack for use before relocation is on. */
|
|
ld r1,PACAEMERGSP(r13)
|
|
subi r1,r1,STACK_FRAME_MIN_SIZE
|
|
|
|
/* See if we need to call a cpu state restore handler */
|
|
LOAD_REG_ADDR(r23, cur_cpu_spec)
|
|
ld r23,0(r23)
|
|
ld r12,CPU_SPEC_RESTORE(r23)
|
|
cmpdi 0,r12,0
|
|
beq 3f
|
|
#ifdef CONFIG_PPC64_ELF_ABI_V1
|
|
ld r12,0(r12)
|
|
#endif
|
|
mtctr r12
|
|
bctrl
|
|
|
|
3: LOAD_REG_ADDR(r3, spinning_secondaries) /* Decrement spinning_secondaries */
|
|
lwarx r4,0,r3
|
|
subi r4,r4,1
|
|
stwcx. r4,0,r3
|
|
bne 3b
|
|
isync
|
|
|
|
4: HMT_LOW
|
|
lbz r23,PACAPROCSTART(r13) /* Test if this processor should */
|
|
/* start. */
|
|
cmpwi 0,r23,0
|
|
beq 4b /* Loop until told to go */
|
|
|
|
sync /* order paca.run and cur_cpu_spec */
|
|
isync /* In case code patching happened */
|
|
|
|
b __secondary_start
|
|
#endif /* SMP */
|
|
|
|
/*
|
|
* Turn the MMU off.
|
|
* Assumes we're mapped EA == RA if the MMU is on.
|
|
*/
|
|
#ifdef CONFIG_PPC_BOOK3S
|
|
SYM_FUNC_START_LOCAL(__mmu_off)
|
|
mfmsr r3
|
|
andi. r0,r3,MSR_IR|MSR_DR
|
|
beqlr
|
|
mflr r4
|
|
andc r3,r3,r0
|
|
mtspr SPRN_SRR0,r4
|
|
mtspr SPRN_SRR1,r3
|
|
sync
|
|
rfid
|
|
b . /* prevent speculative execution */
|
|
SYM_FUNC_END(__mmu_off)
|
|
|
|
SYM_FUNC_START_LOCAL(start_initialization_book3s)
|
|
mflr r25
|
|
|
|
/* Setup some critical 970 SPRs before switching MMU off */
|
|
mfspr r0,SPRN_PVR
|
|
srwi r0,r0,16
|
|
cmpwi r0,0x39 /* 970 */
|
|
beq 1f
|
|
cmpwi r0,0x3c /* 970FX */
|
|
beq 1f
|
|
cmpwi r0,0x44 /* 970MP */
|
|
beq 1f
|
|
cmpwi r0,0x45 /* 970GX */
|
|
bne 2f
|
|
1: bl __cpu_preinit_ppc970
|
|
2:
|
|
|
|
/* Switch off MMU if not already off */
|
|
bl __mmu_off
|
|
|
|
/* Now the MMU is off, can return to our PAGE_OFFSET address */
|
|
tovirt(r25,r25)
|
|
mtlr r25
|
|
blr
|
|
SYM_FUNC_END(start_initialization_book3s)
|
|
#endif
|
|
|
|
/*
|
|
* Here is our main kernel entry point. We support currently 2 kind of entries
|
|
* depending on the value of r5.
|
|
*
|
|
* r5 != NULL -> OF entry, we go to prom_init, "legacy" parameter content
|
|
* in r3...r7
|
|
*
|
|
* r5 == NULL -> kexec style entry. r3 is a physical pointer to the
|
|
* DT block, r4 is a physical pointer to the kernel itself
|
|
*
|
|
*/
|
|
__start_initialization_multiplatform:
|
|
/* Make sure we are running in 64 bits mode */
|
|
bl enable_64b_mode
|
|
|
|
/* Zero r13 (paca) so early program check / mce don't use it */
|
|
li r13,0
|
|
|
|
/* Poison TOC */
|
|
li r2,-1
|
|
|
|
/*
|
|
* Are we booted from a PROM Of-type client-interface ?
|
|
*/
|
|
cmpldi cr0,r5,0
|
|
beq 1f
|
|
b __boot_from_prom /* yes -> prom */
|
|
1:
|
|
/* Save parameters */
|
|
mr r31,r3
|
|
mr r30,r4
|
|
#ifdef CONFIG_PPC_EARLY_DEBUG_OPAL
|
|
/* Save OPAL entry */
|
|
mr r28,r8
|
|
mr r29,r9
|
|
#endif
|
|
|
|
/* Get TOC pointer (current runtime address) */
|
|
bl relative_toc
|
|
|
|
/* These functions return to the virtual (PAGE_OFFSET) address */
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
bl start_initialization_book3e
|
|
#else
|
|
bl start_initialization_book3s
|
|
#endif /* CONFIG_PPC_BOOK3E_64 */
|
|
|
|
/* Get TOC pointer, virtual */
|
|
bl relative_toc
|
|
|
|
/* find out where we are now */
|
|
|
|
/* OPAL doesn't pass base address in r4, have to derive it. */
|
|
bcl 20,31,$+4
|
|
0: mflr r26 /* r26 = runtime addr here */
|
|
addis r26,r26,(_stext - 0b)@ha
|
|
addi r26,r26,(_stext - 0b)@l /* current runtime base addr */
|
|
|
|
b __after_prom_start
|
|
|
|
__REF
|
|
__boot_from_prom:
|
|
#ifdef CONFIG_PPC_OF_BOOT_TRAMPOLINE
|
|
/* Get TOC pointer, non-virtual */
|
|
bl relative_toc
|
|
|
|
/* find out where we are now */
|
|
bcl 20,31,$+4
|
|
0: mflr r26 /* r26 = runtime addr here */
|
|
addis r26,r26,(_stext - 0b)@ha
|
|
addi r26,r26,(_stext - 0b)@l /* current runtime base addr */
|
|
|
|
/* Save parameters */
|
|
mr r31,r3
|
|
mr r30,r4
|
|
mr r29,r5
|
|
mr r28,r6
|
|
mr r27,r7
|
|
|
|
/*
|
|
* Align the stack to 16-byte boundary
|
|
* Depending on the size and layout of the ELF sections in the initial
|
|
* boot binary, the stack pointer may be unaligned on PowerMac
|
|
*/
|
|
rldicr r1,r1,0,59
|
|
|
|
#ifdef CONFIG_RELOCATABLE
|
|
/* Relocate code for where we are now */
|
|
mr r3,r26
|
|
bl relocate
|
|
#endif
|
|
|
|
/* Restore parameters */
|
|
mr r3,r31
|
|
mr r4,r30
|
|
mr r5,r29
|
|
mr r6,r28
|
|
mr r7,r27
|
|
|
|
/* Do all of the interaction with OF client interface */
|
|
mr r8,r26
|
|
bl CFUNC(prom_init)
|
|
#endif /* #CONFIG_PPC_OF_BOOT_TRAMPOLINE */
|
|
|
|
/* We never return. We also hit that trap if trying to boot
|
|
* from OF while CONFIG_PPC_OF_BOOT_TRAMPOLINE isn't selected */
|
|
trap
|
|
.previous
|
|
|
|
__after_prom_start:
|
|
#ifdef CONFIG_RELOCATABLE
|
|
/* process relocations for the final address of the kernel */
|
|
lwz r7,(FIXED_SYMBOL_ABS_ADDR(__run_at_load))(r26)
|
|
cmplwi cr0,r7,1 /* flagged to stay where we are ? */
|
|
mr r25,r26 /* then use current kernel base */
|
|
beq 1f
|
|
LOAD_REG_IMMEDIATE(r25, PAGE_OFFSET) /* else use static kernel base */
|
|
1: mr r3,r25
|
|
bl relocate
|
|
#if defined(CONFIG_PPC_BOOK3E_64)
|
|
/* IVPR needs to be set after relocation. */
|
|
bl init_core_book3e
|
|
#endif
|
|
#endif
|
|
|
|
/*
|
|
* We need to run with _stext at physical address PHYSICAL_START.
|
|
* This will leave some code in the first 256B of
|
|
* real memory, which are reserved for software use.
|
|
*
|
|
* Note: This process overwrites the OF exception vectors.
|
|
*/
|
|
LOAD_REG_IMMEDIATE(r3, PAGE_OFFSET)
|
|
mr r4,r26 /* Load the virtual source address into r4 */
|
|
cmpld r3,r4 /* Check if source == dest */
|
|
beq 9f /* If so skip the copy */
|
|
li r6,0x100 /* Start offset, the first 0x100 */
|
|
/* bytes were copied earlier. */
|
|
|
|
#ifdef CONFIG_RELOCATABLE
|
|
/*
|
|
* Check if the kernel has to be running as relocatable kernel based on the
|
|
* variable __run_at_load, if it is set the kernel is treated as relocatable
|
|
* kernel, otherwise it will be moved to PHYSICAL_START
|
|
*/
|
|
lwz r7,(FIXED_SYMBOL_ABS_ADDR(__run_at_load))(r26)
|
|
cmplwi cr0,r7,1
|
|
bne 3f
|
|
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
LOAD_REG_ADDR(r5, __end_interrupts)
|
|
LOAD_REG_ADDR(r11, _stext)
|
|
sub r5,r5,r11
|
|
#else
|
|
/* just copy interrupts */
|
|
LOAD_REG_IMMEDIATE_SYM(r5, r11, FIXED_SYMBOL_ABS_ADDR(__end_interrupts))
|
|
#endif
|
|
b 5f
|
|
3:
|
|
#endif
|
|
/* # bytes of memory to copy */
|
|
lis r5,(ABS_ADDR(copy_to_here, text))@ha
|
|
addi r5,r5,(ABS_ADDR(copy_to_here, text))@l
|
|
|
|
bl copy_and_flush /* copy the first n bytes */
|
|
/* this includes the code being */
|
|
/* executed here. */
|
|
/* Jump to the copy of this code that we just made */
|
|
addis r8,r3,(ABS_ADDR(4f, text))@ha
|
|
addi r12,r8,(ABS_ADDR(4f, text))@l
|
|
mtctr r12
|
|
bctr
|
|
|
|
.balign 8
|
|
p_end: .8byte _end - copy_to_here
|
|
|
|
4:
|
|
/*
|
|
* Now copy the rest of the kernel up to _end, add
|
|
* _end - copy_to_here to the copy limit and run again.
|
|
*/
|
|
addis r8,r26,(ABS_ADDR(p_end, text))@ha
|
|
ld r8,(ABS_ADDR(p_end, text))@l(r8)
|
|
add r5,r5,r8
|
|
5: bl copy_and_flush /* copy the rest */
|
|
|
|
9: b start_here_multiplatform
|
|
|
|
/*
|
|
* Copy routine used to copy the kernel to start at physical address 0
|
|
* and flush and invalidate the caches as needed.
|
|
* r3 = dest addr, r4 = source addr, r5 = copy limit, r6 = start offset
|
|
* on exit, r3, r4, r5 are unchanged, r6 is updated to be >= r5.
|
|
*
|
|
* Note: this routine *only* clobbers r0, r6 and lr
|
|
*/
|
|
_GLOBAL(copy_and_flush)
|
|
addi r5,r5,-8
|
|
addi r6,r6,-8
|
|
4: li r0,8 /* Use the smallest common */
|
|
/* denominator cache line */
|
|
/* size. This results in */
|
|
/* extra cache line flushes */
|
|
/* but operation is correct. */
|
|
/* Can't get cache line size */
|
|
/* from NACA as it is being */
|
|
/* moved too. */
|
|
|
|
mtctr r0 /* put # words/line in ctr */
|
|
3: addi r6,r6,8 /* copy a cache line */
|
|
ldx r0,r6,r4
|
|
stdx r0,r6,r3
|
|
bdnz 3b
|
|
dcbst r6,r3 /* write it to memory */
|
|
sync
|
|
icbi r6,r3 /* flush the icache line */
|
|
cmpld 0,r6,r5
|
|
blt 4b
|
|
sync
|
|
addi r5,r5,8
|
|
addi r6,r6,8
|
|
isync
|
|
blr
|
|
|
|
_ASM_NOKPROBE_SYMBOL(copy_and_flush); /* Called in real mode */
|
|
|
|
.align 8
|
|
copy_to_here:
|
|
|
|
#ifdef CONFIG_SMP
|
|
#ifdef CONFIG_PPC_PMAC
|
|
/*
|
|
* On PowerMac, secondary processors starts from the reset vector, which
|
|
* is temporarily turned into a call to one of the functions below.
|
|
*/
|
|
.section ".text";
|
|
.align 2 ;
|
|
|
|
.globl __secondary_start_pmac_0
|
|
__secondary_start_pmac_0:
|
|
/* NB the entries for cpus 0, 1, 2 must each occupy 8 bytes. */
|
|
li r24,0
|
|
b 1f
|
|
li r24,1
|
|
b 1f
|
|
li r24,2
|
|
b 1f
|
|
li r24,3
|
|
1:
|
|
|
|
_GLOBAL(pmac_secondary_start)
|
|
/* turn on 64-bit mode */
|
|
bl enable_64b_mode
|
|
|
|
li r0,0
|
|
mfspr r3,SPRN_HID4
|
|
rldimi r3,r0,40,23 /* clear bit 23 (rm_ci) */
|
|
sync
|
|
mtspr SPRN_HID4,r3
|
|
isync
|
|
sync
|
|
slbia
|
|
|
|
/* Branch to our PAGE_OFFSET address */
|
|
bcl 20,31,$+4
|
|
1: mflr r11
|
|
addi r11,r11,(2f - 1b)
|
|
tovirt(r11, r11)
|
|
mtctr r11
|
|
bctr
|
|
2:
|
|
bl relative_toc
|
|
|
|
/* Copy some CPU settings from CPU 0 */
|
|
bl __restore_cpu_ppc970
|
|
|
|
/* pSeries do that early though I don't think we really need it */
|
|
mfmsr r3
|
|
ori r3,r3,MSR_RI
|
|
mtmsrd r3 /* RI on */
|
|
|
|
/* Set up a paca value for this processor. */
|
|
LOAD_REG_ADDR(r4,paca_ptrs) /* Load paca pointer */
|
|
ld r4,0(r4) /* Get base vaddr of paca_ptrs array */
|
|
sldi r5,r24,3 /* get paca_ptrs[] index from cpu id */
|
|
ldx r13,r5,r4 /* r13 = paca_ptrs[cpu id] */
|
|
SET_PACA(r13) /* Save vaddr of paca in an SPRG*/
|
|
|
|
/* Mark interrupts soft and hard disabled (they might be enabled
|
|
* in the PACA when doing hotplug)
|
|
*/
|
|
li r0,IRQS_DISABLED
|
|
stb r0,PACAIRQSOFTMASK(r13)
|
|
li r0,PACA_IRQ_HARD_DIS
|
|
stb r0,PACAIRQHAPPENED(r13)
|
|
|
|
/* Create a temp kernel stack for use before relocation is on. */
|
|
ld r1,PACAEMERGSP(r13)
|
|
subi r1,r1,STACK_FRAME_MIN_SIZE
|
|
|
|
b __secondary_start
|
|
|
|
#endif /* CONFIG_PPC_PMAC */
|
|
|
|
/*
|
|
* This function is called after the master CPU has released the
|
|
* secondary processors. The execution environment is relocation off.
|
|
* The paca for this processor has the following fields initialized at
|
|
* this point:
|
|
* 1. Processor number
|
|
* 2. Segment table pointer (virtual address)
|
|
* On entry the following are set:
|
|
* r1 = stack pointer (real addr of temp stack)
|
|
* r24 = cpu# (in Linux terms)
|
|
* r13 = paca virtual address
|
|
* SPRG_PACA = paca virtual address
|
|
*/
|
|
.section ".text";
|
|
.align 2 ;
|
|
|
|
.globl __secondary_start
|
|
__secondary_start:
|
|
/* Set thread priority to MEDIUM */
|
|
HMT_MEDIUM
|
|
|
|
/*
|
|
* Do early setup for this CPU, in particular initialising the MMU so we
|
|
* can turn it on below. This is a call to C, which is OK, we're still
|
|
* running on the emergency stack.
|
|
*/
|
|
bl CFUNC(early_setup_secondary)
|
|
|
|
/*
|
|
* The primary has initialized our kernel stack for us in the paca, grab
|
|
* it and put it in r1. We must *not* use it until we turn on the MMU
|
|
* below, because it may not be inside the RMO.
|
|
*/
|
|
ld r1, PACAKSAVE(r13)
|
|
|
|
/* Clear backchain so we get nice backtraces */
|
|
li r7,0
|
|
mtlr r7
|
|
|
|
/* Mark interrupts soft and hard disabled (they might be enabled
|
|
* in the PACA when doing hotplug)
|
|
*/
|
|
li r7,IRQS_DISABLED
|
|
stb r7,PACAIRQSOFTMASK(r13)
|
|
li r0,PACA_IRQ_HARD_DIS
|
|
stb r0,PACAIRQHAPPENED(r13)
|
|
|
|
/* enable MMU and jump to start_secondary */
|
|
LOAD_REG_ADDR(r3, start_secondary_prolog)
|
|
LOAD_REG_IMMEDIATE(r4, MSR_KERNEL)
|
|
|
|
mtspr SPRN_SRR0,r3
|
|
mtspr SPRN_SRR1,r4
|
|
RFI_TO_KERNEL
|
|
b . /* prevent speculative execution */
|
|
|
|
/*
|
|
* Running with relocation on at this point. All we want to do is
|
|
* zero the stack back-chain pointer and get the TOC virtual address
|
|
* before going into C code.
|
|
*/
|
|
start_secondary_prolog:
|
|
LOAD_PACA_TOC()
|
|
li r3,0
|
|
std r3,0(r1) /* Zero the stack frame pointer */
|
|
bl CFUNC(start_secondary)
|
|
b .
|
|
/*
|
|
* Reset stack pointer and call start_secondary
|
|
* to continue with online operation when woken up
|
|
* from cede in cpu offline.
|
|
*/
|
|
_GLOBAL(start_secondary_resume)
|
|
ld r1,PACAKSAVE(r13) /* Reload kernel stack pointer */
|
|
li r3,0
|
|
std r3,0(r1) /* Zero the stack frame pointer */
|
|
bl CFUNC(start_secondary)
|
|
b .
|
|
#endif
|
|
|
|
/*
|
|
* This subroutine clobbers r11 and r12
|
|
*/
|
|
SYM_FUNC_START_LOCAL(enable_64b_mode)
|
|
mfmsr r11 /* grab the current MSR */
|
|
#ifdef CONFIG_PPC_BOOK3E_64
|
|
oris r11,r11,0x8000 /* CM bit set, we'll set ICM later */
|
|
mtmsr r11
|
|
#else /* CONFIG_PPC_BOOK3E_64 */
|
|
LOAD_REG_IMMEDIATE(r12, MSR_64BIT)
|
|
or r11,r11,r12
|
|
mtmsrd r11
|
|
isync
|
|
#endif
|
|
blr
|
|
SYM_FUNC_END(enable_64b_mode)
|
|
|
|
/*
|
|
* This puts the TOC pointer into r2, offset by 0x8000 (as expected
|
|
* by the toolchain). It computes the correct value for wherever we
|
|
* are running at the moment, using position-independent code.
|
|
*
|
|
* Note: The compiler constructs pointers using offsets from the
|
|
* TOC in -mcmodel=medium mode. After we relocate to 0 but before
|
|
* the MMU is on we need our TOC to be a virtual address otherwise
|
|
* these pointers will be real addresses which may get stored and
|
|
* accessed later with the MMU on. We branch to the virtual address
|
|
* while still in real mode then call relative_toc again to handle
|
|
* this.
|
|
*/
|
|
_GLOBAL(relative_toc)
|
|
#ifdef CONFIG_PPC_KERNEL_PCREL
|
|
tdnei r2,-1
|
|
blr
|
|
#else
|
|
mflr r0
|
|
bcl 20,31,$+4
|
|
0: mflr r11
|
|
ld r2,(p_toc - 0b)(r11)
|
|
add r2,r2,r11
|
|
mtlr r0
|
|
blr
|
|
|
|
.balign 8
|
|
p_toc: .8byte .TOC. - 0b
|
|
#endif
|
|
|
|
/*
|
|
* This is where the main kernel code starts.
|
|
*/
|
|
__REF
|
|
start_here_multiplatform:
|
|
/* Adjust TOC for moved kernel. Could adjust when moving it instead. */
|
|
bl relative_toc
|
|
|
|
/* Clear out the BSS. It may have been done in prom_init,
|
|
* already but that's irrelevant since prom_init will soon
|
|
* be detached from the kernel completely. Besides, we need
|
|
* to clear it now for kexec-style entry.
|
|
*/
|
|
LOAD_REG_ADDR(r11,__bss_stop)
|
|
LOAD_REG_ADDR(r8,__bss_start)
|
|
sub r11,r11,r8 /* bss size */
|
|
addi r11,r11,7 /* round up to an even double word */
|
|
srdi. r11,r11,3 /* shift right by 3 */
|
|
beq 4f
|
|
addi r8,r8,-8
|
|
li r0,0
|
|
mtctr r11 /* zero this many doublewords */
|
|
3: stdu r0,8(r8)
|
|
bdnz 3b
|
|
4:
|
|
|
|
#ifdef CONFIG_PPC_EARLY_DEBUG_OPAL
|
|
/* Setup OPAL entry */
|
|
LOAD_REG_ADDR(r11, opal)
|
|
std r28,0(r11);
|
|
std r29,8(r11);
|
|
#endif
|
|
|
|
#ifndef CONFIG_PPC_BOOK3E_64
|
|
mfmsr r6
|
|
ori r6,r6,MSR_RI
|
|
mtmsrd r6 /* RI on */
|
|
#endif
|
|
|
|
#ifdef CONFIG_RELOCATABLE
|
|
/* Save the physical address we're running at in kernstart_addr */
|
|
LOAD_REG_ADDR(r4, kernstart_addr)
|
|
clrldi r0,r25,2
|
|
std r0,0(r4)
|
|
#endif
|
|
|
|
/* set up a stack pointer */
|
|
LOAD_REG_ADDR(r3,init_thread_union)
|
|
LOAD_REG_IMMEDIATE(r1,THREAD_SIZE)
|
|
add r1,r3,r1
|
|
li r0,0
|
|
stdu r0,-STACK_FRAME_MIN_SIZE(r1)
|
|
|
|
/*
|
|
* Do very early kernel initializations, including initial hash table
|
|
* and SLB setup before we turn on relocation.
|
|
*/
|
|
|
|
#ifdef CONFIG_KASAN
|
|
bl CFUNC(kasan_early_init)
|
|
#endif
|
|
/* Restore parameters passed from prom_init/kexec */
|
|
mr r3,r31
|
|
LOAD_REG_ADDR(r12, DOTSYM(early_setup))
|
|
mtctr r12
|
|
bctrl /* also sets r13 and SPRG_PACA */
|
|
|
|
LOAD_REG_ADDR(r3, start_here_common)
|
|
ld r4,PACAKMSR(r13)
|
|
mtspr SPRN_SRR0,r3
|
|
mtspr SPRN_SRR1,r4
|
|
RFI_TO_KERNEL
|
|
b . /* prevent speculative execution */
|
|
|
|
/* This is where all platforms converge execution */
|
|
|
|
start_here_common:
|
|
/* relocation is on at this point */
|
|
std r1,PACAKSAVE(r13)
|
|
|
|
/* Load the TOC (virtual address) */
|
|
LOAD_PACA_TOC()
|
|
|
|
/* Mark interrupts soft and hard disabled (they might be enabled
|
|
* in the PACA when doing hotplug)
|
|
*/
|
|
li r0,IRQS_DISABLED
|
|
stb r0,PACAIRQSOFTMASK(r13)
|
|
li r0,PACA_IRQ_HARD_DIS
|
|
stb r0,PACAIRQHAPPENED(r13)
|
|
|
|
/* Generic kernel entry */
|
|
bl CFUNC(start_kernel)
|
|
|
|
/* Not reached */
|
|
0: trap
|
|
EMIT_BUG_ENTRY 0b, __FILE__, __LINE__, 0
|
|
.previous
|