6ca80638b9
Use more inclusive terms throughout the DSA subsystem by moving away from "master" which is replaced by "conduit" and "slave" which is replaced by "user". No functional changes. Acked-by: Rob Herring <robh@kernel.org> Acked-by: Stephen Hemminger <stephen@networkplumber.org> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Florian Fainelli <florian.fainelli@broadcom.com> Link: https://lore.kernel.org/r/20231023181729.1191071-2-florian.fainelli@broadcom.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
446 lines
21 KiB
ReStructuredText
446 lines
21 KiB
ReStructuredText
=========================
|
|
NXP SJA1105 switch driver
|
|
=========================
|
|
|
|
Overview
|
|
========
|
|
|
|
The NXP SJA1105 is a family of 10 SPI-managed automotive switches:
|
|
|
|
- SJA1105E: First generation, no TTEthernet
|
|
- SJA1105T: First generation, TTEthernet
|
|
- SJA1105P: Second generation, no TTEthernet, no SGMII
|
|
- SJA1105Q: Second generation, TTEthernet, no SGMII
|
|
- SJA1105R: Second generation, no TTEthernet, SGMII
|
|
- SJA1105S: Second generation, TTEthernet, SGMII
|
|
- SJA1110A: Third generation, TTEthernet, SGMII, integrated 100base-T1 and
|
|
100base-TX PHYs
|
|
- SJA1110B: Third generation, TTEthernet, SGMII, 100base-T1, 100base-TX
|
|
- SJA1110C: Third generation, TTEthernet, SGMII, 100base-T1, 100base-TX
|
|
- SJA1110D: Third generation, TTEthernet, SGMII, 100base-T1
|
|
|
|
Being automotive parts, their configuration interface is geared towards
|
|
set-and-forget use, with minimal dynamic interaction at runtime. They
|
|
require a static configuration to be composed by software and packed
|
|
with CRC and table headers, and sent over SPI.
|
|
|
|
The static configuration is composed of several configuration tables. Each
|
|
table takes a number of entries. Some configuration tables can be (partially)
|
|
reconfigured at runtime, some not. Some tables are mandatory, some not:
|
|
|
|
============================= ================== =============================
|
|
Table Mandatory Reconfigurable
|
|
============================= ================== =============================
|
|
Schedule no no
|
|
Schedule entry points if Scheduling no
|
|
VL Lookup no no
|
|
VL Policing if VL Lookup no
|
|
VL Forwarding if VL Lookup no
|
|
L2 Lookup no no
|
|
L2 Policing yes no
|
|
VLAN Lookup yes yes
|
|
L2 Forwarding yes partially (fully on P/Q/R/S)
|
|
MAC Config yes partially (fully on P/Q/R/S)
|
|
Schedule Params if Scheduling no
|
|
Schedule Entry Points Params if Scheduling no
|
|
VL Forwarding Params if VL Forwarding no
|
|
L2 Lookup Params no partially (fully on P/Q/R/S)
|
|
L2 Forwarding Params yes no
|
|
Clock Sync Params no no
|
|
AVB Params no no
|
|
General Params yes partially
|
|
Retagging no yes
|
|
xMII Params yes no
|
|
SGMII no yes
|
|
============================= ================== =============================
|
|
|
|
|
|
Also the configuration is write-only (software cannot read it back from the
|
|
switch except for very few exceptions).
|
|
|
|
The driver creates a static configuration at probe time, and keeps it at
|
|
all times in memory, as a shadow for the hardware state. When required to
|
|
change a hardware setting, the static configuration is also updated.
|
|
If that changed setting can be transmitted to the switch through the dynamic
|
|
reconfiguration interface, it is; otherwise the switch is reset and
|
|
reprogrammed with the updated static configuration.
|
|
|
|
Switching features
|
|
==================
|
|
|
|
The driver supports the configuration of L2 forwarding rules in hardware for
|
|
port bridging. The forwarding, broadcast and flooding domain between ports can
|
|
be restricted through two methods: either at the L2 forwarding level (isolate
|
|
one bridge's ports from another's) or at the VLAN port membership level
|
|
(isolate ports within the same bridge). The final forwarding decision taken by
|
|
the hardware is a logical AND of these two sets of rules.
|
|
|
|
The hardware tags all traffic internally with a port-based VLAN (pvid), or it
|
|
decodes the VLAN information from the 802.1Q tag. Advanced VLAN classification
|
|
is not possible. Once attributed a VLAN tag, frames are checked against the
|
|
port's membership rules and dropped at ingress if they don't match any VLAN.
|
|
This behavior is available when switch ports join a bridge with
|
|
``vlan_filtering 1``.
|
|
|
|
Normally the hardware is not configurable with respect to VLAN awareness, but
|
|
by changing what TPID the switch searches 802.1Q tags for, the semantics of a
|
|
bridge with ``vlan_filtering 0`` can be kept (accept all traffic, tagged or
|
|
untagged), and therefore this mode is also supported.
|
|
|
|
Segregating the switch ports in multiple bridges is supported (e.g. 2 + 2), but
|
|
all bridges should have the same level of VLAN awareness (either both have
|
|
``vlan_filtering`` 0, or both 1).
|
|
|
|
Topology and loop detection through STP is supported.
|
|
|
|
Offloads
|
|
========
|
|
|
|
Time-aware scheduling
|
|
---------------------
|
|
|
|
The switch supports a variation of the enhancements for scheduled traffic
|
|
specified in IEEE 802.1Q-2018 (formerly 802.1Qbv). This means it can be used to
|
|
ensure deterministic latency for priority traffic that is sent in-band with its
|
|
gate-open event in the network schedule.
|
|
|
|
This capability can be managed through the tc-taprio offload ('flags 2'). The
|
|
difference compared to the software implementation of taprio is that the latter
|
|
would only be able to shape traffic originated from the CPU, but not
|
|
autonomously forwarded flows.
|
|
|
|
The device has 8 traffic classes, and maps incoming frames to one of them based
|
|
on the VLAN PCP bits (if no VLAN is present, the port-based default is used).
|
|
As described in the previous sections, depending on the value of
|
|
``vlan_filtering``, the EtherType recognized by the switch as being VLAN can
|
|
either be the typical 0x8100 or a custom value used internally by the driver
|
|
for tagging. Therefore, the switch ignores the VLAN PCP if used in standalone
|
|
or bridge mode with ``vlan_filtering=0``, as it will not recognize the 0x8100
|
|
EtherType. In these modes, injecting into a particular TX queue can only be
|
|
done by the DSA net devices, which populate the PCP field of the tagging header
|
|
on egress. Using ``vlan_filtering=1``, the behavior is the other way around:
|
|
offloaded flows can be steered to TX queues based on the VLAN PCP, but the DSA
|
|
net devices are no longer able to do that. To inject frames into a hardware TX
|
|
queue with VLAN awareness active, it is necessary to create a VLAN
|
|
sub-interface on the DSA conduit port, and send normal (0x8100) VLAN-tagged
|
|
towards the switch, with the VLAN PCP bits set appropriately.
|
|
|
|
Management traffic (having DMAC 01-80-C2-xx-xx-xx or 01-19-1B-xx-xx-xx) is the
|
|
notable exception: the switch always treats it with a fixed priority and
|
|
disregards any VLAN PCP bits even if present. The traffic class for management
|
|
traffic has a value of 7 (highest priority) at the moment, which is not
|
|
configurable in the driver.
|
|
|
|
Below is an example of configuring a 500 us cyclic schedule on egress port
|
|
``swp5``. The traffic class gate for management traffic (7) is open for 100 us,
|
|
and the gates for all other traffic classes are open for 400 us::
|
|
|
|
#!/bin/bash
|
|
|
|
set -e -u -o pipefail
|
|
|
|
NSEC_PER_SEC="1000000000"
|
|
|
|
gatemask() {
|
|
local tc_list="$1"
|
|
local mask=0
|
|
|
|
for tc in ${tc_list}; do
|
|
mask=$((${mask} | (1 << ${tc})))
|
|
done
|
|
|
|
printf "%02x" ${mask}
|
|
}
|
|
|
|
if ! systemctl is-active --quiet ptp4l; then
|
|
echo "Please start the ptp4l service"
|
|
exit
|
|
fi
|
|
|
|
now=$(phc_ctl /dev/ptp1 get | gawk '/clock time is/ { print $5; }')
|
|
# Phase-align the base time to the start of the next second.
|
|
sec=$(echo "${now}" | gawk -F. '{ print $1; }')
|
|
base_time="$(((${sec} + 1) * ${NSEC_PER_SEC}))"
|
|
|
|
tc qdisc add dev swp5 parent root handle 100 taprio \
|
|
num_tc 8 \
|
|
map 0 1 2 3 5 6 7 \
|
|
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
|
|
base-time ${base_time} \
|
|
sched-entry S $(gatemask 7) 100000 \
|
|
sched-entry S $(gatemask "0 1 2 3 4 5 6") 400000 \
|
|
flags 2
|
|
|
|
It is possible to apply the tc-taprio offload on multiple egress ports. There
|
|
are hardware restrictions related to the fact that no gate event may trigger
|
|
simultaneously on two ports. The driver checks the consistency of the schedules
|
|
against this restriction and errors out when appropriate. Schedule analysis is
|
|
needed to avoid this, which is outside the scope of the document.
|
|
|
|
Routing actions (redirect, trap, drop)
|
|
--------------------------------------
|
|
|
|
The switch is able to offload flow-based redirection of packets to a set of
|
|
destination ports specified by the user. Internally, this is implemented by
|
|
making use of Virtual Links, a TTEthernet concept.
|
|
|
|
The driver supports 2 types of keys for Virtual Links:
|
|
|
|
- VLAN-aware virtual links: these match on destination MAC address, VLAN ID and
|
|
VLAN PCP.
|
|
- VLAN-unaware virtual links: these match on destination MAC address only.
|
|
|
|
The VLAN awareness state of the bridge (vlan_filtering) cannot be changed while
|
|
there are virtual link rules installed.
|
|
|
|
Composing multiple actions inside the same rule is supported. When only routing
|
|
actions are requested, the driver creates a "non-critical" virtual link. When
|
|
the action list also contains tc-gate (more details below), the virtual link
|
|
becomes "time-critical" (draws frame buffers from a reserved memory partition,
|
|
etc).
|
|
|
|
The 3 routing actions that are supported are "trap", "drop" and "redirect".
|
|
|
|
Example 1: send frames received on swp2 with a DA of 42:be:24:9b:76:20 to the
|
|
CPU and to swp3. This type of key (DA only) when the port's VLAN awareness
|
|
state is off::
|
|
|
|
tc qdisc add dev swp2 clsact
|
|
tc filter add dev swp2 ingress flower skip_sw dst_mac 42:be:24:9b:76:20 \
|
|
action mirred egress redirect dev swp3 \
|
|
action trap
|
|
|
|
Example 2: drop frames received on swp2 with a DA of 42:be:24:9b:76:20, a VID
|
|
of 100 and a PCP of 0::
|
|
|
|
tc filter add dev swp2 ingress protocol 802.1Q flower skip_sw \
|
|
dst_mac 42:be:24:9b:76:20 vlan_id 100 vlan_prio 0 action drop
|
|
|
|
Time-based ingress policing
|
|
---------------------------
|
|
|
|
The TTEthernet hardware abilities of the switch can be constrained to act
|
|
similarly to the Per-Stream Filtering and Policing (PSFP) clause specified in
|
|
IEEE 802.1Q-2018 (formerly 802.1Qci). This means it can be used to perform
|
|
tight timing-based admission control for up to 1024 flows (identified by a
|
|
tuple composed of destination MAC address, VLAN ID and VLAN PCP). Packets which
|
|
are received outside their expected reception window are dropped.
|
|
|
|
This capability can be managed through the offload of the tc-gate action. As
|
|
routing actions are intrinsic to virtual links in TTEthernet (which performs
|
|
explicit routing of time-critical traffic and does not leave that in the hands
|
|
of the FDB, flooding etc), the tc-gate action may never appear alone when
|
|
asking sja1105 to offload it. One (or more) redirect or trap actions must also
|
|
follow along.
|
|
|
|
Example: create a tc-taprio schedule that is phase-aligned with a tc-gate
|
|
schedule (the clocks must be synchronized by a 1588 application stack, which is
|
|
outside the scope of this document). No packet delivered by the sender will be
|
|
dropped. Note that the reception window is larger than the transmission window
|
|
(and much more so, in this example) to compensate for the packet propagation
|
|
delay of the link (which can be determined by the 1588 application stack).
|
|
|
|
Receiver (sja1105)::
|
|
|
|
tc qdisc add dev swp2 clsact
|
|
now=$(phc_ctl /dev/ptp1 get | awk '/clock time is/ {print $5}') && \
|
|
sec=$(echo $now | awk -F. '{print $1}') && \
|
|
base_time="$(((sec + 2) * 1000000000))" && \
|
|
echo "base time ${base_time}"
|
|
tc filter add dev swp2 ingress flower skip_sw \
|
|
dst_mac 42:be:24:9b:76:20 \
|
|
action gate base-time ${base_time} \
|
|
sched-entry OPEN 60000 -1 -1 \
|
|
sched-entry CLOSE 40000 -1 -1 \
|
|
action trap
|
|
|
|
Sender::
|
|
|
|
now=$(phc_ctl /dev/ptp0 get | awk '/clock time is/ {print $5}') && \
|
|
sec=$(echo $now | awk -F. '{print $1}') && \
|
|
base_time="$(((sec + 2) * 1000000000))" && \
|
|
echo "base time ${base_time}"
|
|
tc qdisc add dev eno0 parent root taprio \
|
|
num_tc 8 \
|
|
map 0 1 2 3 4 5 6 7 \
|
|
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 \
|
|
base-time ${base_time} \
|
|
sched-entry S 01 50000 \
|
|
sched-entry S 00 50000 \
|
|
flags 2
|
|
|
|
The engine used to schedule the ingress gate operations is the same that the
|
|
one used for the tc-taprio offload. Therefore, the restrictions regarding the
|
|
fact that no two gate actions (either tc-gate or tc-taprio gates) may fire at
|
|
the same time (during the same 200 ns slot) still apply.
|
|
|
|
To come in handy, it is possible to share time-triggered virtual links across
|
|
more than 1 ingress port, via flow blocks. In this case, the restriction of
|
|
firing at the same time does not apply because there is a single schedule in
|
|
the system, that of the shared virtual link::
|
|
|
|
tc qdisc add dev swp2 ingress_block 1 clsact
|
|
tc qdisc add dev swp3 ingress_block 1 clsact
|
|
tc filter add block 1 flower skip_sw dst_mac 42:be:24:9b:76:20 \
|
|
action gate index 2 \
|
|
base-time 0 \
|
|
sched-entry OPEN 50000000 -1 -1 \
|
|
sched-entry CLOSE 50000000 -1 -1 \
|
|
action trap
|
|
|
|
Hardware statistics for each flow are also available ("pkts" counts the number
|
|
of dropped frames, which is a sum of frames dropped due to timing violations,
|
|
lack of destination ports and MTU enforcement checks). Byte-level counters are
|
|
not available.
|
|
|
|
Limitations
|
|
===========
|
|
|
|
The SJA1105 switch family always performs VLAN processing. When configured as
|
|
VLAN-unaware, frames carry a different VLAN tag internally, depending on
|
|
whether the port is standalone or under a VLAN-unaware bridge.
|
|
|
|
The virtual link keys are always fixed at {MAC DA, VLAN ID, VLAN PCP}, but the
|
|
driver asks for the VLAN ID and VLAN PCP when the port is under a VLAN-aware
|
|
bridge. Otherwise, it fills in the VLAN ID and PCP automatically, based on
|
|
whether the port is standalone or in a VLAN-unaware bridge, and accepts only
|
|
"VLAN-unaware" tc-flower keys (MAC DA).
|
|
|
|
The existing tc-flower keys that are offloaded using virtual links are no
|
|
longer operational after one of the following happens:
|
|
|
|
- port was standalone and joins a bridge (VLAN-aware or VLAN-unaware)
|
|
- port is part of a bridge whose VLAN awareness state changes
|
|
- port was part of a bridge and becomes standalone
|
|
- port was standalone, but another port joins a VLAN-aware bridge and this
|
|
changes the global VLAN awareness state of the bridge
|
|
|
|
The driver cannot veto all these operations, and it cannot update/remove the
|
|
existing tc-flower filters either. So for proper operation, the tc-flower
|
|
filters should be installed only after the forwarding configuration of the port
|
|
has been made, and removed by user space before making any changes to it.
|
|
|
|
Device Tree bindings and board design
|
|
=====================================
|
|
|
|
This section references ``Documentation/devicetree/bindings/net/dsa/nxp,sja1105.yaml``
|
|
and aims to showcase some potential switch caveats.
|
|
|
|
RMII PHY role and out-of-band signaling
|
|
---------------------------------------
|
|
|
|
In the RMII spec, the 50 MHz clock signals are either driven by the MAC or by
|
|
an external oscillator (but not by the PHY).
|
|
But the spec is rather loose and devices go outside it in several ways.
|
|
Some PHYs go against the spec and may provide an output pin where they source
|
|
the 50 MHz clock themselves, in an attempt to be helpful.
|
|
On the other hand, the SJA1105 is only binary configurable - when in the RMII
|
|
MAC role it will also attempt to drive the clock signal. To prevent this from
|
|
happening it must be put in RMII PHY role.
|
|
But doing so has some unintended consequences.
|
|
In the RMII spec, the PHY can transmit extra out-of-band signals via RXD[1:0].
|
|
These are practically some extra code words (/J/ and /K/) sent prior to the
|
|
preamble of each frame. The MAC does not have this out-of-band signaling
|
|
mechanism defined by the RMII spec.
|
|
So when the SJA1105 port is put in PHY role to avoid having 2 drivers on the
|
|
clock signal, inevitably an RMII PHY-to-PHY connection is created. The SJA1105
|
|
emulates a PHY interface fully and generates the /J/ and /K/ symbols prior to
|
|
frame preambles, which the real PHY is not expected to understand. So the PHY
|
|
simply encodes the extra symbols received from the SJA1105-as-PHY onto the
|
|
100Base-Tx wire.
|
|
On the other side of the wire, some link partners might discard these extra
|
|
symbols, while others might choke on them and discard the entire Ethernet
|
|
frames that follow along. This looks like packet loss with some link partners
|
|
but not with others.
|
|
The take-away is that in RMII mode, the SJA1105 must be let to drive the
|
|
reference clock if connected to a PHY.
|
|
|
|
RGMII fixed-link and internal delays
|
|
------------------------------------
|
|
|
|
As mentioned in the bindings document, the second generation of devices has
|
|
tunable delay lines as part of the MAC, which can be used to establish the
|
|
correct RGMII timing budget.
|
|
When powered up, these can shift the Rx and Tx clocks with a phase difference
|
|
between 73.8 and 101.7 degrees.
|
|
The catch is that the delay lines need to lock onto a clock signal with a
|
|
stable frequency. This means that there must be at least 2 microseconds of
|
|
silence between the clock at the old vs at the new frequency. Otherwise the
|
|
lock is lost and the delay lines must be reset (powered down and back up).
|
|
In RGMII the clock frequency changes with link speed (125 MHz at 1000 Mbps, 25
|
|
MHz at 100 Mbps and 2.5 MHz at 10 Mbps), and link speed might change during the
|
|
AN process.
|
|
In the situation where the switch port is connected through an RGMII fixed-link
|
|
to a link partner whose link state life cycle is outside the control of Linux
|
|
(such as a different SoC), then the delay lines would remain unlocked (and
|
|
inactive) until there is manual intervention (ifdown/ifup on the switch port).
|
|
The take-away is that in RGMII mode, the switch's internal delays are only
|
|
reliable if the link partner never changes link speeds, or if it does, it does
|
|
so in a way that is coordinated with the switch port (practically, both ends of
|
|
the fixed-link are under control of the same Linux system).
|
|
As to why would a fixed-link interface ever change link speeds: there are
|
|
Ethernet controllers out there which come out of reset in 100 Mbps mode, and
|
|
their driver inevitably needs to change the speed and clock frequency if it's
|
|
required to work at gigabit.
|
|
|
|
MDIO bus and PHY management
|
|
---------------------------
|
|
|
|
The SJA1105 does not have an MDIO bus and does not perform in-band AN either.
|
|
Therefore there is no link state notification coming from the switch device.
|
|
A board would need to hook up the PHYs connected to the switch to any other
|
|
MDIO bus available to Linux within the system (e.g. to the DSA conduit's MDIO
|
|
bus). Link state management then works by the driver manually keeping in sync
|
|
(over SPI commands) the MAC link speed with the settings negotiated by the PHY.
|
|
|
|
By comparison, the SJA1110 supports an MDIO slave access point over which its
|
|
internal 100base-T1 PHYs can be accessed from the host. This is, however, not
|
|
used by the driver, instead the internal 100base-T1 and 100base-TX PHYs are
|
|
accessed through SPI commands, modeled in Linux as virtual MDIO buses.
|
|
|
|
The microcontroller attached to the SJA1110 port 0 also has an MDIO controller
|
|
operating in master mode, however the driver does not support this either,
|
|
since the microcontroller gets disabled when the Linux driver operates.
|
|
Discrete PHYs connected to the switch ports should have their MDIO interface
|
|
attached to an MDIO controller from the host system and not to the switch,
|
|
similar to SJA1105.
|
|
|
|
Port compatibility matrix
|
|
-------------------------
|
|
|
|
The SJA1105 port compatibility matrix is:
|
|
|
|
===== ============== ============== ==============
|
|
Port SJA1105E/T SJA1105P/Q SJA1105R/S
|
|
===== ============== ============== ==============
|
|
0 xMII xMII xMII
|
|
1 xMII xMII xMII
|
|
2 xMII xMII xMII
|
|
3 xMII xMII xMII
|
|
4 xMII xMII SGMII
|
|
===== ============== ============== ==============
|
|
|
|
|
|
The SJA1110 port compatibility matrix is:
|
|
|
|
===== ============== ============== ============== ==============
|
|
Port SJA1110A SJA1110B SJA1110C SJA1110D
|
|
===== ============== ============== ============== ==============
|
|
0 RevMII (uC) RevMII (uC) RevMII (uC) RevMII (uC)
|
|
1 100base-TX 100base-TX 100base-TX
|
|
or SGMII SGMII
|
|
2 xMII xMII xMII xMII
|
|
or SGMII or SGMII
|
|
3 xMII xMII xMII
|
|
or SGMII or SGMII SGMII
|
|
or 2500base-X or 2500base-X or 2500base-X
|
|
4 SGMII SGMII SGMII SGMII
|
|
or 2500base-X or 2500base-X or 2500base-X or 2500base-X
|
|
5 100base-T1 100base-T1 100base-T1 100base-T1
|
|
6 100base-T1 100base-T1 100base-T1 100base-T1
|
|
7 100base-T1 100base-T1 100base-T1 100base-T1
|
|
8 100base-T1 100base-T1 n/a n/a
|
|
9 100base-T1 100base-T1 n/a n/a
|
|
10 100base-T1 n/a n/a n/a
|
|
===== ============== ============== ============== ==============
|